Search

This paper presents a 5-level inverter topology for open-end induction motor drives by using a single dc source. The open stator windings of the drive are supplied with a 3-level flying capacitor inverter from one end and capacitor-fed 2-level inverter from another end. The voltage ratio of the dc link to the capacitor in 2-level inverter is maintained at 4:1 ratio to generate five-level voltage output. The capacitor in 2-level inverter is balanced by the switching redundant vector combinations from both the inverters while the floating capacitors in the 3-level inverter are balanced by using redundant switching states. The proposed topology gives 5-level operation with less number of floating capacitors and power semiconductor switches compared to other existing topologies. Also, the balancing of the capacitors is independent of load power factor and modulation index. Further, the generalization of the proposed dual inverter scheme for any n-level inverter is also included in this paper. The experimental results and required analysis are also presented to validate the inverter scheme. [ABSTRACT FROM AUTHOR]

In this paper, many impedance-source inverters with coupled inductors have been investigated to obtain a high step-up boost ratio. However, the leakage inductors in these topologies induce great voltage spikes at the dc link, which will increase the voltage stress of switches. Thus, the power level of inverters is limited. Furthermore, the efficiency of the inverters can be degraded by the losses associated with leakage inductors. To address abovementioned issues, this paper proposes a family of low-spike high-efficiency Y-source inverters. The proposed inverters have the ability of eliminating voltage spikes at the dc link and recycling the leakage energy via the additional diode and capacitor. In order to show the excellent characteristics of the proposed topologies, this paper compares the performances of the proposed inverters and the improved-Y-source inverter in many aspects. Simulation and experimental results have verified the abilities of the proposed inverters. [ABSTRACT FROM AUTHOR]

Reduced switch active phase converters (APC) are cost-effective solutions for running three-phase loads from single-phase grids. This paper proposes a novel auxiliary-capacitor-based APC (AC-APC) for this application. The combination of the topological location of the auxiliary capacitor and the control of the AC-APC reduces current stress on the semiconductor devices. In this paper, a selection criterion for the optimal auxiliary capacitor value is formulated to reduce the device currents in such a way that the overall efficiency is enhanced. This paper presents a comparative analysis of converter volt-ampere (VA) rating and device power loss for conventional H-bridge active front-end and inverter-based topology, APC, and AC-APC. To evaluate the efficacy of the proposed AC-APC, an experimental study is conducted on the APC and the AC-APC feeding a 3-hp three-phase induction motor. At a full load of $\text{2.5}\,\text{kW}$ and $\text{0.8 } \text{power factor}$ , the measured maximum efficiency of the AC-APC is $2\%$ higher than that of the APC. Analytical evaluation of converter currents and device power loss are in close agreement with experimental observations. [ABSTRACT FROM AUTHOR]

This paper proposes a new dc–ac converter with a reduced number of semiconductor switches and gate drive and control circuit components. A salient feature of this inverter is its pure sinusoidal line-to-line voltages with no need for output filter. Also, the proposed inverter improves the voltage utilization factor of the input dc supply compared to the four-switch three-phase inverter (first best topology in the literature from the number of switches point of view) and standard six-switch inverter with sine pulsewidth modulation. The proposed inverter is capable of operating with a wide range of output voltages from zero to the full value of the dc input voltage by appropriately altering the instantaneous duty cycle. A three-phase universal inverter with only three power switch has been proposed in this paper for the first time ever, to our knowledge. For the purpose of providing a good compromise between fast transient response and stability, a model predictive controller is proposed. All the design expressions have been derived. A comparison with other dc–ac converters is given to show the merits of the proposed converter. Finally, satisfactory circuit operation is confirmed by experimental results from a laboratory prototype. [ABSTRACT FROM AUTHOR]

In this paper, two structures are proposed for the switched-inductor quasi-Z-source inverter. In the proposed structures to extend the voltage gain of inverter, two new switched-inductor structures are used. In the proposed structures, voltage across the capacitors in the Z-source network and in the switched-inductor is symmetric and small. The other advantage of proposed inverters is known as achieving higher voltage gain per smaller duty cycle ratio (of shoot-through). Compared with a conventional continuous input current switched-inductor quasi-Z-source inverter at the same gain voltage, there is less of a ripple of input current in the proposed inverters. In this paper, at first the both the conventional and the proposed switched-inductor Z-source inventers are thoroughly investigated to find out their governing relations. Then, the proposed Z-source inverters are compared with the conventional ones by simulating them to assess their performance efficiency. Next, applying the simple boost pulse width modulation the simulation is carried out with PSCAD/EMTDC software. After that, to evaluate the obtained results, the prototypes of the proposed inverters with 48 Vdc input voltage are used. [ABSTRACT FROM PUBLISHER]

This paper analyzes the combination in a cascaded H-bridge multilevel inverter (CHBI) based on transformers with the different turn ratios for increasing the voltage level and proposes the switching method for achieving the output voltage distribution among H-bridge cells (HBCs). The transformers used in this paper are connected to the output of the respective HBCs, and the secondary sides of all the transformers are connected in series for generating the final output voltage. Only one of the transformers, in particular, has a different turn ratio for increasing the output voltage level. In this paper, the possible turn ratio of the special transformer with a different turn ratio is discussed in detail, and a switching method based on the level-shifted switching method for the topology used in this paper is proposed. To verify the effectiveness of the proposed method, a three-phase 21-level CHBI is experimentally tested. [ABSTRACT FROM PUBLISHER]

This paper presents a new multilevel converter topology based on a variable or multilevel dc-link stage. This stage is shared by all inverter output phases, thus increasing the number of output voltage levels while reducing the overall number of active devices compared to traditional topologies; therefore, it is called a reduced multilevel converter (RMC). The converter is not capable of reducing the blocking voltage of the devices; hence, unlike other multilevel converters aimed at medium-voltage applications, this converter is interesting for low-voltage- and high-power-quality-demanding applications such as photovoltaic inverters, wind energy conversion systems, and uninterruptible power supplies. The main novelty behind the proposed concept is the basic dc cell used to generate the variable dc-link voltage, which includes a controlled path through the floating capacitors to provide the necessary degree of control to enable a shared multilevel dc link for all the output phases of the converter. The dc cells are connected in a multicell structure to increase the number of levels of the converter. A five-level version of the RMC topology is briefly compared to other five-level converters such as the five-level active neutral-point-clamped converter and the five-level flying capacitor converter. This paper presents the structure of the new topology with its operating principle, switching states, main characteristics, and experimental validation using finite-control-set model-predictive control. [ABSTRACT FROM PUBLISHER]

In this paper, new half-bridge and full-bridge topologies for a switched-boost inverter are proposed. These topologies have a high boost factor in comparison with conventional types. In addition, the proposed topologies have continuous input current and can generate zero-voltage level in output. In this paper, the operation of the proposed inverters in different operating modes is analyzed. Then, the values of inductors and capacitors are designed. Moreover, the used switching pattern and its logical diagram are introduced. A comprehensive comparison between the proposed and conventional topologies in terms of the boost factor, the number of elements, and the efficiency shows the good features of the proposed inverters. Finally, to verify correct operation of the proposed topologies and derived equations, simulation and experimental results are presented. [ABSTRACT FROM AUTHOR]

This paper proposes and validates model predictive control as an alternative control strategy for H-bridgeneutral-point-clamped (H-NPC) converters for single-phase grid-tied string photovoltaic (PV) systems. The presented control scheme achieves good quality current waveforms with unity power factor, dc-link voltage control, and neutral-point voltage minimization. Furthermore, the predictive controller has been further enhanced by including an average device switching frequency restriction and a $dv/dt$ mitigation. The main contribution of this paper is the avoidance of the potential leakage current due to parasitic capacitance of the PV modules by using a predictive model based control technique instead of modulated schemes and eliminating high-frequency common-mode voltage components. Experimental results during steady state and dynamic operation are presented to illustrate the behavior of the H-NPC converter commanded by the proposed control scheme. [ABSTRACT FROM AUTHOR]

In this paper, two topologies are presented for the enhanced-boost quasi-Z-source inverters (qZSI), namely continuous input current configuration and discontinuous input current configuration of enhanced-boost qZSI with two-switched impedance networks. Similar to enhanced-boost impedance-source inverters (ZSIs), these proposed inverter topologies possess very high boost voltage inversion at low shoot-through duty ratio and high modulation index to provide an improved quality output voltage. Compared to enhanced-boost ZSIs with two-switched Z-source impedance networks, these proposed inverter topologies share common ground with source and bridge inverter, overcome the starting inrush problem, and draw continuous input current and the lower voltage across the capacitors. Moreover, the input ripple current is negligible. This paper presents the operating principles and analysis of continuous input current configuration enhanced-boost qZSI with two-switched impedance networks and compares with ZSI, switched inductor ZSI, DA/CA-qZSI, and enhanced-boost ZSIs. The theoretical analysis is done and is validated through simulation and experimental results. [ABSTRACT FROM PUBLISHER]

This paper proposes an effective sliding mode controller (SMC) for a grid-connected 7-level packed U-cell (PUC7) inverter. The aim is to design a simple controller that deals effectively with the complex control problem of the PUC7 inverter (multiobjective control problem). The selection of the control actions is achieved according to the system state error at every sampling time, regardless of the previous values, which makes the control technique model-independent. The control algorithm evaluates online two cost functions (one for each state error), which are derived on the basis of sliding mode theory, and it selects the optimal control input in order to satisfy the reaching conditions of the two cost functions. Compared with the existing solutions, the proposed SMC technique ensures lower average switching frequency by tuning the hysteresis bandwidth of the capacitor-voltage error. The fast implementation, needless of gains tuning, and simple design procedure are the main features of the proposed algorithm. Simulation and experimental results are presented to prove the effectiveness of the proposed technique in controlling the PUC7 inverter with high dynamic performance and robustness against disturbances and parameters mismatch. [ABSTRACT FROM AUTHOR]

This paper proposes a new multilevel inverter (MLI) topology that utilizes trinary sequence for the dc sources. It gives maximum output voltage level with minimum dc source and switch count when compared to other sequences, such as symmetric, natural, binary, and quasi-linear. This is due to the fact that the trinary sequence generates of all additive and subtractive combinations of input dc levels in the output voltage waveform. The concept is implemented on a 9-level asymmetric MLI using only four active devices. Multicarrier unipolar pulsewidth modulation technique is adopted to create the switching pulses. Theoretical calculation of total harmonic distortion in both voltage and current waveforms has been performed using asymptotic time domain formula. These values are compared with simulation and experimental values for different modulation indices. Power loss calculation for proposed topology is discussed with appropriate mathematical equations. [ABSTRACT FROM AUTHOR]

The conventional three-level inverter only has voltage buck capability. The quasi-Z-source three-level T-type inverter (QZS 3LT $^2$ I) has been proposed to realize voltage buck–boost operation. In this paper, we further propose a novel modulation scheme for the QZS 3LT $^2$ I to realize voltage boosting, reduce the common-mode voltage (CMV), and control the neutral-point voltage balance simultaneously. The proposed scheme adopts a large vector, a medium vector, a small vector with low CMV magnitude, a zero vector, and a shoot-through vector to generate the output voltage. According to sector number and neutral-point voltage difference, a p-type or n-type small vector with low CMV magnitude is properly selected to balance the neutral-point voltage. Shoot-through states are inserted within zero vector to boost the dc input voltage without affecting the ac output voltage. Dwell times of basic vectors are calculated through the revised volt–second balance equation. Furthermore, a coordinate control strategy between neutral-point voltage balance and voltage boosting is proposed. Doing so, the CMV magnitude can be restricted within one-sixth of dc-link voltage and neutral-point voltage imbalance can be effectively mitigated. The effectiveness of the proposed scheme is verified by simulations and experiments. [ABSTRACT FROM AUTHOR]

A multilevel drive can be realized by using an open-ended machine, fed from dual two-level inverters. The topology supplied from isolated dc sources is suitable for transportation electrification. In vehicular systems, it is essential that the isolated dc sources, comprising of battery packs, should discharge uniformly and maintain balanced dc voltage at the dc-link terminal. A simple carrier-based pulsewidth modulation (PWM) technique is presented in this paper, which can effectively regulate the power drawn between the two two-level inverters while maintaining the multilevel operation of the drive. The modulation technique can balance the instantaneous state of charge of independent battery packs and dynamically equalize the power flow from the two inverters, based on drive requirement. This will enhance the reliability of the propulsion system in electric vehicles. The operation of the proposed PWM technique has been validated through detailed simulation and experimental tests. [ABSTRACT FROM AUTHOR]

This paper deals with the analysis of the input dc-link voltage ripple in multilevel inverter based on H-bridge and level doubling network (LDN). The LDN is basically a half-bridge fed by a floating capacitor, with voltage self-balancing capability, recalling the concept of a flying capacitor configuration. The amplitude of the LDN voltage ripple is analytically determined considering both the low-order and the switching harmonic components. In particular, peak-to-peak distributions of voltage ripples over the fundamental period are analytically determined, making possible the design of dc-link capacitor relying only on the dc-voltage ripple requirements. The case study makes reference to negligible switching ripple in the output current. It well represents either grid connection or passive load having almost sinusoidal currents. Numerical simulations carried out by MATLAB/Simulink and a complete set of experimental verifications are given to confirm the theoretical developments. [ABSTRACT FROM AUTHOR]

In this paper, a novel structure of switched capacitor converter (SCC) is proposed. First, the basic unit of the proposed SCC is presented. After that, a generalized structure of the proposed SCC is discussed. The presented SCC uses one dc source, several switches, diodes, and capacitors to produce multistep dc boosted output voltage. The capacitors in the SCC can be charged in trinary asymmetrical pattern. A detailed comparative study between the proposed and other recently developed SCC structures is presented. It is shown that the proposed SCC can produce an output voltage level with lower total standing voltage and lower maximum switch stress voltage as compared to most of the suggested SCC structures. Further, a switched capacitor multilevel inverter (SCMLI) based on cross-switched multilevel inverter has been developed and analyzed for symmetric and asymmetric dc source configurations. For fair comparison with the existing SCMLI structures, the overall cost of the structures is compared based on a cost function (CF). The proposed SCMLI provides lower cost function/output voltage level (CF/NL) in comparison with most of the other SCMLI structures for both symmetric and asymmetric dc source configurations. Extensive experimental studies validate the operation and performance of the proposed SCMLI structure. [ABSTRACT FROM AUTHOR]

In this paper, a new topology for half-bridge Z-source inverter is proposed. The proposed topology has only one impedance network. Unlike to the conventional half-bridge inverter, the proposed topology can provide zero voltage level at the output. It also increases output voltage level and stabilizes it in the desired value. Capacitor voltage stress in the proposed topology is low, and, therefore, nominal voltage of capacitor and cost decreases. In this paper, the steady-state analysis of the proposed inverter in two new operations which are named synchronous operation of diodes and asynchronous operation of diodes is conducted based on mathematics calculations. A method to obtain high-voltage gains by cascading the Z-network and combining middle inductors is presented that leads to cost, size, and weight reduction. Comparison among the proposed converter with conventional ones shows its excellent performance. The experimental results have good agreement with analytical analysis for the proposed topology. [ABSTRACT FROM PUBLISHER]

Zero-common-mode-voltage (CMV) operation of multilevel inverters results in reduced dc-bus utilization and reduced linear modulation range. In this paper, a method to increase the linear modulation range for zero-CMV operation without increasing the dc-bus voltage using a cascaded multilevel inverter with a single dc supply is presented. Using this method, the peak fundamental output voltage can be increased from 0.499 to 0.637  \textV\text{dc} with zero CMV inside the linear modulation range. Also, various pulse width modulation (PWM) switching sequences are analyzed in this paper, and the PWM sequence that gives minimum current ripple is used for the zero-CMV operation of the inverter. The inverter topology with single dc supply is realized by cascading a two-level inverter with two floating-capacitor-fed full-bridge modules. Simulation and experimental results for steady-state and dynamic operating conditions are presented to validate the proposed method. [ABSTRACT FROM AUTHOR]

This paper presents a model predictive control technique applied to a dual-active bridge inverter where one of the bridges is floating. The proposed floating bridge topology eliminates the need for isolation transformer in a dual inverter system and therefore reduces the size, weight, and losses in the system. To achieve multilevel output voltage waveforms, the floating inverter dc-link capacitor is charged to the half of the main dc-link voltage. A finite-set model predictive control technique is used to control the load current of the converter as well as the floating capacitor voltage. Model predictive control does not require any switching sequence design or complex switching time calculations as used for space vector modulation; thus, the technique has some advantages in this application. A detailed analysis of the converter as well as the predictive control strategy is given in this paper. Simulation and experimental results to validate the approach are also presented. [ABSTRACT FROM PUBLISHER]

This paper presents a three-phase open-end winding induction motor drive. The drive consists of a three-phase induction machine with open stator phase windings and dual-bridge inverter supplied from a single dc voltage source. To achieve multilevel output voltage waveforms, a floating capacitor bank is used for the second of the dual bridges. The capacitor voltage is regulated using redundant switching states at half of the main dc-link voltage. This particular voltage ratio (2:1) is used to create a multilevel output voltage waveform with three levels. A modified modulation scheme is used to improve the waveform quality of this dual inverter. This paper also compares the losses in the dual-inverter system in contrast with a single-sided three-level neutral point clamped converter. Finally, detailed simulation and experimental results are presented for the motor drive operating as an open-loop v /f controlled motor drive and as a closed-loop field-oriented motor controller. [ABSTRACT FROM PUBLISHER]

This paper presents a new reconfiguration module for asymmetrical multilevel inverters in which the capacitors are used as the dc links to create the levels for staircase waveforms. This configuration of the multilevel converter makes a reduction in dc sources. On the other hand, it is possible to generate 13 levels with lower dc sources. The proposed module of the multilevel inverter generates 13 levels with two unequal dc sources (2VDC and 1VDC). It also involves two chargeable capacitors and 14 semiconductor switches. The capacitors are self-charging without any extra circuit. The lower number of components makes it desirable to be used in wide range of applications. The module is schematized as two back-to-back T-type inverters and some other switches around it. Also, it can be connected as a cascade modular which leads to a modular topology with more voltage levels at higher voltages. The proposed module makes the inherent creation of the negative voltage levels without any additional circuit (such as H-bridge circuit). Nearest level control switching modulation scheme is applied to achieve high-quality sinusoidal output voltage. Simulations are executed in MATLAB/Simulink and a prototype is implemented in the power electronics laboratory in which the simulation and experimental results show a good performance. [ABSTRACT FROM AUTHOR]

This paper presents a high-efficiency inverter with the aid of the soft-switching technology, which is accomplished by the resonance of the in-series inductance with the snubber capacitance. The equivalent circuit of the quarter-phase ultrasonic motor is initially deduced, based on which the topology along with the operations of the novel inverter is subsequently presented. The configuration of the new quarter-phase inverter shows its uniqueness in terms of the shared arms and the especially designed snubber capacitance in comparison with the existing inverters. The circuit analysis infers that the dead time of the inverter is the key factor to arrive at the zero-voltage-switching or the zero-current-switching operations. Experimental measurements have demonstrated that the efficiency of the whole drive increases by a factor of 1.25 after replacing the traditional inverter with the proposed one. It should also be noted that the proposed inverter in association with the design method of the dead time not only can work for the quarter-phase ultrasonic motor, but also can be applicable for other kinds of quarter-phase devices. The soft-switching operations are achieved in the quarter-phase inverter for the first time, whose amplitudes of the output voltage and switching frequency are not required to be constant any more. [ABSTRACT FROM AUTHOR]

The development of a photovoltaic ac module composed of a high static gain nonisolated dc–dc converter with current source output characteristic followed by an unfolding low-frequency inverter is presented in this paper. The operation of the dc–dc converter with high static gain and with reduced switch voltage is obtained using the Cuk converter integrated with the switched-inductor technique. The nonisolated structure allows the elimination of the volume and losses of the power transformer and leakage inductance, and an output filter configuration is proposed to reduce the high-frequency ground leakage current. The grid-tied inverter operating in a discontinuous conduction mode (DCM) allows a sinusoidal output current with low harmonic distortion (THD = 3.72%) to be obtained without current control loop and without the use of a current sensor at the output. The maximum power point tracking operation is obtained without the use of the current sensor. The DCM operation increases the current stress, but the proposed converter presents two switches and two input inductors sharing the input current in these components. The theoretical analysis, design procedure, and experimental results are presented for a prototype with a dc input voltage Vi = 30 V, an ac output voltage Vo = 127 V, and output power Po = 180 W. [ABSTRACT FROM AUTHOR]

In this paper, a fixed switching frequency model predictive current controller is designed and implemented on a sensorless five-level packed U-cell (PUC5) inverter interfacing the utility. The predictive control methodology is based on a voltage vector generation technique for the cost function optimization by nullifying its derivative. The aim of the controller is to allow a fixed-frequency operation with no iterations while operating as a utility line current regulator. A pulsewidth modulator based on employing PUC5 redundant switching states fixes the PUC5 auxiliary dc bus capacitor voltage to its desired level with no necessity of a regulator; the overall technique reduces system complexity with less sensors and no loops in the predictive algorithm making it suitable for industrial applications. System discrete model is developed and experimental results verify the performance of the designed controller in making a fast response in regulating the grid current and balancing the capacitor voltage. [ABSTRACT FROM AUTHOR]

Conventional two-level as well as multilevel voltage-source-inverter topologies with a hexagonal voltage-space vector structure generate low-order harmonics in the machine terminal voltages when operated beyond the linear modulation range in variable speed drive application. Progressing from hexagonal to a higher sided polygonal voltage-space-vector structure (VSVS) suppresses significant low-order harmonics throughout the modulation range. In addition, the linear modulation range will also be enhanced very near to the base speed. In this paper, for the first time, the generation of a multilevel 24-sided VSVS using a single dc source for induction-motor drives is proposed. A cascaded topology with a dc-source-fed flying-capacitor inverter and two low-voltage capacitor-fed H-bridge cells forms the power circuit. The features and advantages of the proposed scheme are validated through experimental results and discussions. [ABSTRACT FROM AUTHOR]

Usually, the parallel-compensated inductive power transfer (IPT) topology fed by a current-source inverter is controlled through variable switching frequency and fixed 50% duty cycle method. This enables the system to operate at resonance frequency, which drifts due to load and other parameter variations. Owing to this control constraint, the load requirements are fulfilled by adding extra dc–dc chopper at the output. This paper presents a new control technique for a parallel–series/series IPT network, fed from a full-bridge current-source inverter to meet the load demand directly by an inverter. Therefore, the extra chopper stage at the output side of the converter is eliminated. The control goals are achieved through a two-loop control method, where the inner input current loop controls the source current and the outer output current loop meets the load requirements. The detailed steady-state operation, converter design, small-signal modeling, and control are reported, and experimental results obtained from a 1.6-kW lab prototype are included to verify the mathematical analysis. [ABSTRACT FROM AUTHOR]

This paper proposes a zero-sequence circulating current (ZSCC) control scheme for the multiparalleled three-level T-type inverters (3LT2Is). Based on the analysis with the proposed generalized model of multiparalleled 3LT2Is, it is seen that the ZSCC is influenced by the circuit parameters, duty cycles, and the circulating currents of the l th and first 3LT2I. To mitigate the circulating currents, a deadbeat control strategy for n-paralleled (n≥3) inverters is proposed, which is realized by adjusting the duty cycle of the small vectors in each PWM sampling period. Compared with the conventional PI control method, the ZSCC spike is mitigated with the proposed scheme, thus improving the quality of the output currents. Also, the reliability of the 3LT2Is system is improved because such a scheme only needs the information about the ZSCC and zero-sequence duty ratio in the l th and the first inverter. The proposed method can also be applied to the neutral-point-clamped converters. Simulation and experimental results verify the effectiveness of the theoretical analysis and the proposed method. [ABSTRACT FROM PUBLISHER]

Microinverters operating into the single-phase grid from new energy source with low-voltage output face the challenges of efficiency bottleneck and twice-line-frequency variation. This paper proposed a multilevel inverter based on bridge modular switched-capacitor (BMSC) circuits with its superiority in conversion efficiency and power density. The topology is composed of dc–dc and dc–ac stages with independent control for each stage, aiming to improve system stability and simplify the control method. The BMSC dc–dc stage, which can be expanded to synthesize more levels, not only features multilevel voltage gain but also partially replaces the original bulk input capacitor and functions as an active energy buffer to enhance power-decoupling ability between dc and ac sides. In dc–ac stage, the control strategy of optimized unipolar frequency doubling sine-wave pulse width modulation is proposed to improve the quality of output waveform. Meanwhile, the multilevel voltage phase has been optimized to further reduce the power loss. Finally, a prototype has been built and tested. Associated with the simulation, the experimental results validate the practicability of these analyses. [ABSTRACT FROM PUBLISHER]

A new pulsewidth modulation (PWM) strategy which is an alternative approach of the discontinuous PWM (DPWM) for a three-level neutral-point-clamped (NPC) inverter is proposed in this paper. A three-level NPC inverter is completely mature and very well-established topology in high-power applications. However, the three-level NPC inverter has an inheritance problem of the neutral-point voltage unbalancing due to the split dc-link capacitors. This structure can cause large neutral-point voltage ripple. Furthermore, output currents of the three-level NPC inverter are distorted by the neutral-point voltage ripple. Therefore, the neutral-point voltage must be controlled. In this paper, a new DPWM method using two different offsets for the neutral-point ripple reduction is proposed and the effectiveness of the proposed DPWM method is verified by using the simulation and the experimental results. [ABSTRACT FROM PUBLISHER]

A four-level five-phase open-end winding (OeW) drive topology is introduced in this paper. The drive comprises a five-phase induction machine with open-end stator windings, supplied using two two-level voltage-source inverters with isolated and unequal dc-link voltages, in the ratio 2 : 1. The topology offers the advantages of a modular structure with fewer semiconductor components and has a greater potential for fault tolerance, as compared with an equivalent single-sided four-level drive. Due to the large number of switching states, development of a suitable space vector pulsewidth-modulation (PWM) method can be challenging. Hence, this paper examines the implementation of two-level-shifted carrier-based PWM methods. The effect of dead time on the drive performance is discussed, and it is shown that simultaneous PWM switching of both inverters can lead to degraded output phase voltage waveforms. Detailed analysis of this phenomenon is presented, a solution is proposed, and the modified modulation techniques are incorporated in an experimental setup, at first in conjunction with $V/f$ control. Once the proof of concept has been provided, full field-oriented control is implemented in this OeW drive topology for the first time; detailed experimental testing is conducted, and results are reported. [ABSTRACT FROM AUTHOR]

Multiphase variable-speed drives and generation systems (systems with more than three phases) have become one of the mainstream research areas during the last decade. The main driving forces are the specific applications, predominantly related to the green agenda, such as electric and hybrid electric vehicles (EVs), locomotive traction, ship propulsion, “more-electric” aircraft, remote offshore wind farms for electric energy generation, and general high-power industrial applications. As a result, produced body of significant work is substantial, making it impossible to review all the major developments in a single paper. This paper therefore surveys the recent progress in two specific areas associated with multiphase systems, namely power electronic supply control and innovative ways of using the additional degrees of freedom in multiphase machines for various nontraditional purposes. [ABSTRACT FROM AUTHOR]

Multilevel inverters with dodecagonal (12-sided polygon) voltage space vector structure have advantages, such as complete elimination of fifth and seventh harmonics, reduction in electromagnetic interference, reduction in device voltage ratings, reduction of switching frequency, extension of linear modulation range, etc., making it a viable option for high-power medium-voltage drives. This paper proposes two power circuit topologies capable of generating multilevel dodecagonal voltage space vector structure with symmetric triangles (for the first time) with minimum number of dc-link power supplies and floating capacitor H-bridges. The first power topology is composed of two hybrid cascaded five-level inverters connected to either side of an open-end winding induction machine. Each inverter consists of a three-level neutral-point-clamped inverter, which is cascaded with an isolated H-bridge making it a five-level inverter. The second topology is for a normal induction motor. Both of these circuit topologies have inherent capacitor balancing for floating H-bridges for all modulation indexes, including transient operations. The proposed topologies do not require any precharging circuitry for startup. A simple pulsewidth modulation timing calculation method for space vector modulation is also presented in this paper. Due to the symmetric arrangement of congruent triangles within the voltage space vector structure, the timing computation requires only the sampled reference values and does not require any offline computation, lookup tables, or angle computation. Experimental results for steady-state operation and transient operation are also presented to validate the proposed concept. [ABSTRACT FROM PUBLISHER]

In this paper, the conventional I- and T-type three-level neutral-point-clamped (3L-NPC) inverter for low-voltage renewable energy systems is first investigated. Literature research shows that the T-type inverter improves I-type's insulated-gate bipolar transistor (IGBT) $+$ IGBT current paths. However, the IGBT $+$ diode paths are the same. The calculation in this paper further reveals that the IGBT $+$ diode current paths dominate the conduction losses and even the whole semiconductor losses. Based on the aforementioned recognitions, a novel T-type inverter is presented as an alternative to be applied in the low-voltage renewable energy systems. In the proposed 3L-NPC, four CoolMosfets replace the IGBT $+$ diode middle bidirectional switch. In the proposed topology, there is no diode involved in the current path supposing the unity power factor. In this way, the conduction loss is expected to be reduced compared with that from the conventional T-type 3L-NPC, particularly in the low and medium power ranges. [ABSTRACT FROM PUBLISHER]

A circuit configuration, a circuit topological family, a buck-mode active clamped circuit, and an instantaneous output voltage feedback control strategy of combined bidirectional buck–boost dc–dc chopper-mode inverter with high-frequency (HF) link (HFL) were proposed and fully investigated in this paper. The steady principle characteristic and the design criteria for the key circuit parameters were given in this paper. The circuit configuration is composed of two identical isolated bidirectional buck–boost dc–dc choppers with the same input and output filters. These two choppers in parallel at input end and in series at output end generate unipolarity sinusoidal pulsewidth modulation current waveforms with positive and negative half low-frequency cycles separately. The circuit topological family includes four circuit topologies, such as one-transistor mode. Taking the one-transistor mode circuit topology as an example, the 750VA48VDC/220V50HzAC prototype is designed and implemented. The theoretical analysis and principle test show the inverters have excellent performance. [ABSTRACT FROM PUBLISHER]

This paper proposes the combination of a novel modified quasi-Z-source (MqZS) inverter with a single-phase symmetrical hybrid three-level inverter in order to boost the inverter three-level output voltage. The proposed single-phase MqZS hybrid three-level inverter provides a higher boost ability and reduces the number of inductors in the source impedance, compared with both the single-phase three-level neural-point clamped quasi-Z-source inverter and the single-phase quasi-Z-source cascaded multilevel inverter. Additionally, it can be extended to obtain the nine-level output voltage by cascading two three-level pulse width modulation switching cells with a separate MqZS and a dc source, which herein is called a single-phase MqZS cascaded hybrid five-level inverter (MqZS-CHI). A modified modulation technique based on an alternative phase opposition disposition scheme is suggested to effectively control the shoot-through state for boosting the dc-link voltage and balancing the two series capacitor voltages of the MqZS. The performances of both the proposed MqZS-CHI and the modulation techniques are verified through simulation and experimental results. [ABSTRACT FROM PUBLISHER]

This paper presents a nine-level active-neutral-point-clamped (ANPC) based multilevel inverter (MLI) topology for grid-connected applications requiring only ten switches. The envisaged structure comprises two parts, namely five-level ANPC unit, and a two-level converter leg whose midpoint is used as another ac terminal. An ad hoc switching state redundancy based modulation strategy is used to ensure that the voltage across the flying capacitor is tightly balanced and is implemented using a look-up table further simplifies the control complexity. The performance and effectiveness of the proposed topology with its control scheme are validated through simulations and experimental tests. Comparison with other MLIs is included to highlight the merits of the proposed topology. From the results, it will be shown that the proposed inverter requires the least part count as compared to other topologies with the same performance and output quality. [ABSTRACT FROM PUBLISHER]

Cascaded H-bridge (CHB) multilevel inverters (MLIs) have been widely used for power electronics systems. While high-voltage blocking across power switches is not a constraint for low voltage applications, the research trend has been oriented to the design of more compact module topologies as an alternative for CHB. Despite the generation of more voltage levels with reduced switch count, the existing module topologies in recent literature take no account of the freewheeling current path during dead-time, thus, inducing multistep jumps in voltage levels and giving rise to undesirable voltage spikes. Addressing this concern, this paper proposes two symmetrical compact-module topologies for cascaded MLI, where freewheeling current path during dead-time is provided for smooth transition between voltage levels to prevent voltage spikes. The proposed 7-level and 13-level compact-modules demonstrated low number of conducting switches for all voltage levels. Comprehensive analysis and comparison with the latest module topologies are conducted. To validate the operation of the proposed compact-module topologies, simulation and experimental results are presented. [ABSTRACT FROM PUBLISHER]

Z-source networks are recently being employed to enhance the boosting capability of matrix converters. This paper concentrates on cascaded Z-source ultrasparse matrix converter (ZSUSMC), where the Z-source network is placed between the three-switch input rectifier stage and the six-switch output inverter stage. Two space vector modulation schemes, with and without a zero state in the rectifier stage modulation, are presented and their advantages and disadvantages are discussed. In addition, restrictions imposed on the converter operation in buck mode, which arise from unidirectional nature of the ultrasparse matrix converter, are discussed and a solution is proposed for offsetting those limitations. Furthermore, an optimal switching pattern, which results in minimum possible number of changes in the switching states as well as even distribution of the shoot-through state over the entire control period, is proposed. Also, common-mode voltages of the converter in all possible switching configurations are calculated. Hardware-in-the-loop studies of a ZSUSMC-based permanent magnet synchronous motor drive are carried out to evaluate the performance of the drive under the proposed modulation techniques. The obtained results are compared with a recent study and the superiority of the proposed method in terms of converter input/output current quality is demonstrated. [ABSTRACT FROM PUBLISHER]

This paper presents an optimized topology of 3-$\phi$ , multilevel inverter (MLI) configuration for five or higher level operation with reduced switch count. The proposed solution consists of two basic units (BUs) of multilevel converter and a T-structured 3-level inverter (3-LI). Both BUs are equally shared by the three phases maintaining symmetry among the phases. Moreover, for a higher level operation of the proposed MLI, the modifications required are at two BUs only and not at three legs of the inverter. It further helps in reducing the requirement of extra components for higher level operation compared to the conventional solutions. Furthermore, the topology also has the benefits of reduced switching and conduction loss. An algorithm is also devised to generate the switching pulses for the BUs and the 3-LI, using a carrier-based space vector modulation technique. Presented topology is compared with other existing topologies to prove its advantage. All the details regarding the operating modes and pulse width modulation techniques employed for the proposed system are given and supported by the simulation and experimental results. [ABSTRACT FROM AUTHOR]

Adding the auxiliary switches to the conventional H-bridge inverter is an effective way to eliminate the leakage current for transformerless PV systems, such as H5, H6, etc. Inspired by the newly developed embedded-switch H6 topology, a novel embedded-switch inverter (ESI) is proposed in this paper for three-phase transformerless PV systems. First, the operation principle and characteristics of the proposed ESI are analyzed. Second, the common-mode model of the three-phase ESI is established, based on which the main factors that affect the leakage current are discussed. The finding reveals that the switching states with conventional modulation strategy result in high-frequency common-mode voltage, which is the source of leakage current. In order to solve the problem, a new modulation strategy is presented for ESI to eliminate the high-frequency leakage current. Finally, the time-domain simulation and the experimental tests are carried out. The results verify the effectiveness of the proposed solution. [ABSTRACT FROM AUTHOR]

This paper proposes a family of novel flying capacitor transformerless inverters for single-phase photovoltaic (PV) systems. Each of the new topologies proposed is based on a flying capacitor principle and requires only four power switches and/or diodes, one capacitor, and a small filter at the output stage. A simple unipolar sinusoidal pulse width modulation technique is used to modulate the inverter to minimize the switching loss, output current ripple, and the filter requirements. In general, the main advantages of the new inverter topologies are: 1) the negative polarity of the PV is directly connected to the grid, and therefore, no leakage current; 2) reactive power compensation capability; and 3) the output ac voltage peak is equal to the input dc voltage (unlike neutral-point-clamped and derivative topologies, which requires twice the magnitude of the peak ac voltage). A complete description of the operating principle with modulation techniques, design guidelines, and comprehensive comparisons is presented to reveal the properties and limitations of each topology in detail. Finally, experimental results of 1-kVA prototypes are presented to prove the concept and theoretical analysis of the proposed inverter family for practical applications. [ABSTRACT FROM PUBLISHER]

This paper proposes a novel 49-level stacked inverter topology for drives. The 49 levels are achieved by stacking three 17-level inverters. Each of the 17-level inverter is developed by cascading a flying capacitor (FC) inverter with three capacitor-fed H-bridges. The device count can be reduced by making the FC and the three cascaded H-bridges common to the dc link in each phase using selector switches in between them. The selector switches need to operate at fundamental frequency only. Also, the devices need to block very low voltages. Hence, MOSFETs can be used. This topology requires three dc sources, each of V\text{dc} /6 only, which can be replaced with stacked batteries for electric vehicle applications. The reduction in the dc voltage requirement is achieved by using a normal symmetric six-phase induction motor with parallel connection of the opposite phase windings. All the floating capacitors in the topology can be balanced irrespective of any modulation index or load power factor. Due to the high number of voltage levels, nearest level control can be used instead of pulse width modulation, which reduces the switching losses. The $dv/dt$ during the inverter operation is also less. Detailed experimental results at different speeds of operation and during transients ensure that the novel topology can be a viable option for high-power adjustable speed drives. [ABSTRACT FROM PUBLISHER]

In this paper, an improved transformerless single-phase single-stage grid-tied flying inductor inverter is presented. The negative terminal of the photovoltaic (PV) array is grounded in the improved topology, which increases reliability and suppresses the leakage current. The proposed topology has buck–boost capability without increasing the number of required components and has a high efficiency. An improved control algorithm for proper operation of the proposed topology which decreases switching losses has been investigated. Moreover, a perturbation and observation maximum power point tracking (MPPT) algorithm has been adapted to the proposed inverter, which does not utilize proportional–integral (PI) controllers, for the purpose of the MPPT. Furthermore, a design procedure of the passive elements of the converter based on the corresponding operating has been demonstrated. Simulation in MATLAB Simulink plus an experimental prototype is developed to reconfirm the designed results. Finally, a comparison study has been investigated for better clarification of the advantages and disadvantages of the proposed inverter. [ABSTRACT FROM PUBLISHER]

For three-phase dual-output dc–ac conversion systems, the nine-switch inverter is one of the most versatile available topologies. Despite some disadvantages, recent studies show that the nine-switch inverter achieves efficiency values equivalent to or higher than its 12-switch counterpart, when operating in certain ranges of the modulation index and displacement angles. The use of proper pulse width modulation techniques is able to increase the efficiency even more, as well as to equalize the loss distribution among the switches, favoring an effective and low-cost thermal design. The available pulse width modulation techniques are complex and do not explore the full capacity of the nine-switch inverter to reduce its losses. For this reason, this paper proposes an unrestricted generalized scalar pulse width modulation for nine-switch inverters. Based on this new generalization, a current peak tracking technique is also proposed, achieving small average number of switchings and the highest overall efficiency when compared with other techniques, likewise a more balanced loss distribution among the switches. Experimental results are carried out to demonstrate the validity of the new generalization and the effectiveness of the proposed technique in reducing the switching losses. [ABSTRACT FROM PUBLISHER]

In this paper, a switching loss-free (SLF) concept for the first six-switches H-bridge inverter (H6-I) topology is proposed. SLF means that its switches are able to operate with soft turn-on and turn-off transitions. In order to implement the SLF goal, a new resonance-trajectory is proposed. Compared with the zero-current-transition H6-I (ZCT-H6-I) topology published in previous literature, the proposed resonance-trajectory can precisely compensate for losses of resonant tanks every switching period. With this intention, an implementing circuit is structured based on the H6-I topology, and its detailed operation principle and performance characteristics are analyzed. As a result, all active switches of the new circuit are switched under zero-current turn-on and zero-current turn-off conditions. Also, the reverse recovery problem of freewheeling diodes is alleviated owing to the zero-current turn-off property of diodes. The SLF target is realized in theory. Finally, experimental results from a 1 kW prototype at 50 kHz switching frequency are provided to verify the effectiveness of the proposed SLF concept in practice. Specifically, the conversion efficiency of the new circuit is over 95% in a wide load range, and there is roughly a 1.5% efficiency improvement compared with the hard-switching H6-I topology. [ABSTRACT FROM PUBLISHER]

Existing integrated chargers are configured to charge from single- or three-phase ac networks. With the rapid emergence of dc grids, there is growing interest in the development of high-efficiency low-cost integrated chargers interfaced with dc power outlets. This paper introduces a new integrated charger offering electric vehicle fast charging from emerging dc distribution networks. In absence of a dc grid, the charger can alternatively be fed from a simple uncontrolled rectifier. The proposed charger leverages the dual-inverter topology previously developed for high-speed drive applications. By connecting the charger inlet to the differential ends of the traction inverters, charging is enabled for a wide battery voltage range previously unattainable using an integrated charger based on the single traction drive. An 11-kW experimental setup demonstrates rapid charging using constant current control and energy balancing of dual storage media. To minimize the harmonic impact of the charger on the dc distribution network, a combination of complementary and interleaved switching methods is demonstrated. [ABSTRACT FROM PUBLISHER]

Photovoltaic (PV) microinverters dispense with the line frequency transformer, however at the cost of system grounding and ground leakage current problems. These have been erstwhile resolved by the topologies derived from buck, boost, buck–boost, Zeta, Watkins–Johnson, and Ćuk converters, or combinations of these. The Ćuk derived inverters, employing second-order input and output filters, offer the most efficient, lightweight, and economical solution in the class. This paper presents design and detailed operation of a Ćuk derived, common-ground PV microinverter in continuous conduction mode operation. The inverter is shown to be compatible with both linear and nonlinear loads, in stand-alone and grid-connected modes of operation. Optimal design rules of passive components are rigorously derived to ensure attenuation of input voltage ripples arising from the twin effects of switching and double-frequency output power oscillation. Additionally, the design rules also incorporate considerations of efficiency maximization and some aspects of easing control complexity. Inverter performance is experimentally validated with a 300 VA, 110 V, and 50/60 Hz laboratory prototype. [ABSTRACT FROM PUBLISHER]

Grid-connected power conversion systems for renewable energy sources must fulfill several requirements, e.g., the high efficiency, the reduced cost and complexity, and, quite often, the boost capabilities that is usually achieved using a front-end dc–dc boost converter before the inversion stage, leading to a two-stage architecture. Meanwhile, single-stage power conversion systems, which perform the boosting operation within the inversion one, offer some potential advantages, in terms of reducing the complexity and the volume of the whole system. Among several proposed options, the split-source inverter (SSI) has been recently proposed by Abdelhakim et al. as an alternative option with some interesting features to the commonly used Z-source inverter. Taking into account that the SSI is controlled by a single parameter, i.e., its dc and ac sides are controlled by the modulation index, it is of paramount importance to investigate its control scheme in grid-connected mode, which has never been studied yet. Hence, this paper models the SSI dc side and proposes a modified modulation scheme combined with the commonly used synchronous reference frame control technique to achieve a decoupled control scheme of the SSI in grid-connected mode, i.e., the dc and the ac sides of the SSI can be controlled independently, which is convenient for many applications. The introduced control scheme is analyzed and simulated using a MATLAB/Simulink model, where a reduced scale 1-kVA grid-connected SSI is designed and simulated for the sake of experimental validation. Finally, the designed system is implemented experimentally to validate and verify the reported analysis and simulations. [ABSTRACT FROM PUBLISHER]

In recent years, high photovoltaic array voltage up to 1000 V and transformerless grid-tied inverter have been increasingly researched and applied to elevate the inverter and the dc power collection efficiency. With the same reasons, a three-level neutral point clamped (3L-NPC) inverter featuring low power device voltage stress and low leakage current becomes increasingly attractive. In this paper, the operation and the features of a novel grid-tied 3L-NPC are presented. The proposed topology is a derivative of the three-level stacked neutral point clamped (3L-SNPC) structure. However, compared with the conventional 3L-SNPC and its pulse width modulation (PWM) strategy, the new topology with novel PWM strategy features completely inactive intrinsic body diodes. Furthermore, only two outer power devices are working with switching frequency, while the other four Insulated Gate Bipolar Transistors (IGBTs) are actually with the grid frequency. Therefore, the relatively high switching frequency is selected to reduce the inverter output filter inductance. A hybrid CoolMosfet and IGBT power module configuration is also proposed based on the new PWM strategy. The calculation shows that the total power device losses are reduced. The experimental results are illustrated in this paper to confirm the operation of the proposed topology and controller. [ABSTRACT FROM PUBLISHER]

A new approach for modulation of an 11-level cascade multilevel inverter using selective harmonic elimination is presented in this paper. The dc sources feeding the multilevel inverter are considered to be varying in time, and the switching angles are adapted to the dc source variation. This method uses genetic algorithms to obtain switching angles offline for different dc source values. Then, artificial neural networks are used to determine the switching angles that correspond to the real-time values of the dc sources for each phase. This implies that each one of the dc sources of this topology can have different values at any time, but the output fundamental voltage will stay constant and the harmonic content will still meet the specifications. The modulating switching angles are updated at each cycle of the output fundamental voltage. This paper gives details on the method in addition to simulation and experimental results. [ABSTRACT FROM PUBLISHER]