Search

A space vector modulation (SVM) technique of a dual-inverter system for an open-end winding motor drive is described in this paper, where one inverter has a battery power source and the other has an only capacitor across the dc bus. The SVM must be achieved to operate the motor with field-oriented control and simultaneously to control the capacitor voltage at a constant value by using redundant switching states of the dual-inverter system. The control of the capacitor voltage is carried out by selecting a charging or a discharging mode in each redundant switching state, taking the instantaneous motor power factor into account. In addition, it is also required to reduce the error voltage pulses, which are generated in output multilevel voltage waveforms during the dead time. The compensation method of the existing dead-time scheme and the improved SVM sequence to reduce the error voltage vectors are proposed in this paper. The proposed methods are examined through several experimental tests and are confirmed to generate superior output voltage waveforms from the viewpoint of the measured total harmonic distortion and dv/dt. [ABSTRACT FROM AUTHOR]

This paper analyzes the combination in a cascaded H-bridge multilevel inverter (CHBI) based on transformers with the different turn ratios for increasing the voltage level and proposes the switching method for achieving the output voltage distribution among H-bridge cells (HBCs). The transformers used in this paper are connected to the output of the respective HBCs, and the secondary sides of all the transformers are connected in series for generating the final output voltage. Only one of the transformers, in particular, has a different turn ratio for increasing the output voltage level. In this paper, the possible turn ratio of the special transformer with a different turn ratio is discussed in detail, and a switching method based on the level-shifted switching method for the topology used in this paper is proposed. To verify the effectiveness of the proposed method, a three-phase 21-level CHBI is experimentally tested. [ABSTRACT FROM PUBLISHER]

This paper proposes and validates model predictive control as an alternative control strategy for H-bridgeneutral-point-clamped (H-NPC) converters for single-phase grid-tied string photovoltaic (PV) systems. The presented control scheme achieves good quality current waveforms with unity power factor, dc-link voltage control, and neutral-point voltage minimization. Furthermore, the predictive controller has been further enhanced by including an average device switching frequency restriction and a $dv/dt$ mitigation. The main contribution of this paper is the avoidance of the potential leakage current due to parasitic capacitance of the PV modules by using a predictive model based control technique instead of modulated schemes and eliminating high-frequency common-mode voltage components. Experimental results during steady state and dynamic operation are presented to illustrate the behavior of the H-NPC converter commanded by the proposed control scheme. [ABSTRACT FROM AUTHOR]

For the purpose of improving the performances of T-type neutral point clamped (T-NPC) photovoltaic (PV) grid-connected inverter under large grid, a passivity-based decoupling control scheme is proposed in this paper. First, the Euler–Lagrange (EL) mathematical model of a T-NPC PV grid-connected inverter with an LC filter is built based on the power circuit and operating principles. Second, with this EL mathematical model and passivity of the inverter, the passivity-based controller is designed by the damping injecting method. Third, by adopting a proportional integral regulator to directly control direct current (dc) voltage, together with passivity-based indirect control, better performances of the dc voltage control can be further obtained. With the proposed passivity-based controller, the PV grid-connected inverter can achieve both dynamic current decoupling under the synchronous rotating dq coordinate and dc side voltage dynamic decoupling, which can improve the quality of the current connected into the power grid. The passivity-based PV grid-connected inverter is with strong robustness against parameters perturbations of resistors and attenuating the influence of delay in the inverter. Moreover, the passivity-based decoupling control scheme proposed in this paper for the T-NPC PV grid-connected inverter has a simple structure, and is easily debugged and realized in engineering. Experimental results under 10-kW prototype show that the proposed control scheme is effective. [ABSTRACT FROM PUBLISHER]

This paper proposes an effective sliding mode controller (SMC) for a grid-connected 7-level packed U-cell (PUC7) inverter. The aim is to design a simple controller that deals effectively with the complex control problem of the PUC7 inverter (multiobjective control problem). The selection of the control actions is achieved according to the system state error at every sampling time, regardless of the previous values, which makes the control technique model-independent. The control algorithm evaluates online two cost functions (one for each state error), which are derived on the basis of sliding mode theory, and it selects the optimal control input in order to satisfy the reaching conditions of the two cost functions. Compared with the existing solutions, the proposed SMC technique ensures lower average switching frequency by tuning the hysteresis bandwidth of the capacitor-voltage error. The fast implementation, needless of gains tuning, and simple design procedure are the main features of the proposed algorithm. Simulation and experimental results are presented to prove the effectiveness of the proposed technique in controlling the PUC7 inverter with high dynamic performance and robustness against disturbances and parameters mismatch. [ABSTRACT FROM AUTHOR]

The conventional three-level inverter only has voltage buck capability. The quasi-Z-source three-level T-type inverter (QZS 3LT $^2$ I) has been proposed to realize voltage buck–boost operation. In this paper, we further propose a novel modulation scheme for the QZS 3LT $^2$ I to realize voltage boosting, reduce the common-mode voltage (CMV), and control the neutral-point voltage balance simultaneously. The proposed scheme adopts a large vector, a medium vector, a small vector with low CMV magnitude, a zero vector, and a shoot-through vector to generate the output voltage. According to sector number and neutral-point voltage difference, a p-type or n-type small vector with low CMV magnitude is properly selected to balance the neutral-point voltage. Shoot-through states are inserted within zero vector to boost the dc input voltage without affecting the ac output voltage. Dwell times of basic vectors are calculated through the revised volt–second balance equation. Furthermore, a coordinate control strategy between neutral-point voltage balance and voltage boosting is proposed. Doing so, the CMV magnitude can be restricted within one-sixth of dc-link voltage and neutral-point voltage imbalance can be effectively mitigated. The effectiveness of the proposed scheme is verified by simulations and experiments. [ABSTRACT FROM AUTHOR]

This paper presents the current control design procedure of a single-phase grid-tied five-level packed U-cell inverter (PUC5) with an LCL output filter. The PUC5 inverter is used as an interface of renewable energy sources, such as solar applications. The LCL filter is calculated according to the grid-tied operation and converter ratings. An optimal controller, based on a linear quadratic regulator with integral action, is designed to inject a sinusoidal current with low harmonic distortion at unity power factor. For that design, the PUC5 inverter is modelled in the D–Q frame. The sensorless voltage control is incorporated into the switching technique to balance the PUC5 capacitor voltage and generate a five-level waveform at the output. Experimental tests are performed on a laboratory benchmark to confirm the theoretical design. The results prove the efficiency and accuracy of the adopted control strategy in a steady state and under transients of grid current, grid inductance, ac and dc voltage amplitudes. [ABSTRACT FROM AUTHOR]

Zero-common-mode-voltage (CMV) operation of multilevel inverters results in reduced dc-bus utilization and reduced linear modulation range. In this paper, a method to increase the linear modulation range for zero-CMV operation without increasing the dc-bus voltage using a cascaded multilevel inverter with a single dc supply is presented. Using this method, the peak fundamental output voltage can be increased from 0.499 to 0.637  \textV\text{dc} with zero CMV inside the linear modulation range. Also, various pulse width modulation (PWM) switching sequences are analyzed in this paper, and the PWM sequence that gives minimum current ripple is used for the zero-CMV operation of the inverter. The inverter topology with single dc supply is realized by cascading a two-level inverter with two floating-capacitor-fed full-bridge modules. Simulation and experimental results for steady-state and dynamic operating conditions are presented to validate the proposed method. [ABSTRACT FROM AUTHOR]

This paper presents a model predictive control technique applied to a dual-active bridge inverter where one of the bridges is floating. The proposed floating bridge topology eliminates the need for isolation transformer in a dual inverter system and therefore reduces the size, weight, and losses in the system. To achieve multilevel output voltage waveforms, the floating inverter dc-link capacitor is charged to the half of the main dc-link voltage. A finite-set model predictive control technique is used to control the load current of the converter as well as the floating capacitor voltage. Model predictive control does not require any switching sequence design or complex switching time calculations as used for space vector modulation; thus, the technique has some advantages in this application. A detailed analysis of the converter as well as the predictive control strategy is given in this paper. Simulation and experimental results to validate the approach are also presented. [ABSTRACT FROM PUBLISHER]

This paper presents a three-phase open-end winding induction motor drive. The drive consists of a three-phase induction machine with open stator phase windings and dual-bridge inverter supplied from a single dc voltage source. To achieve multilevel output voltage waveforms, a floating capacitor bank is used for the second of the dual bridges. The capacitor voltage is regulated using redundant switching states at half of the main dc-link voltage. This particular voltage ratio (2:1) is used to create a multilevel output voltage waveform with three levels. A modified modulation scheme is used to improve the waveform quality of this dual inverter. This paper also compares the losses in the dual-inverter system in contrast with a single-sided three-level neutral point clamped converter. Finally, detailed simulation and experimental results are presented for the motor drive operating as an open-loop v /f controlled motor drive and as a closed-loop field-oriented motor controller. [ABSTRACT FROM PUBLISHER]

This paper presents a novel model predictive control (MPC) for the T-type single-phase three-level inverters. The cumbersome procedure in tuning of weighting factors is eliminated so that the implementation of the proposed MPC becomes easy. The constant switching frequency is achieved during the control implementation in order to facilitate the filter design. In order to optimize the distribution of the output current harmonics, multiple voltage vectors are employed in each control cycle with their application times setting inversely proportion to the respective cost function. The redundant small voltage vectors are utilized to balance the neutral point voltage of the inverter by directly regulating the upper and lower dc-link capacitors voltages. Finally, the proposed MPC algorithm is experimentally evaluated and compared with other two unfixed switching frequency MPC algorithms in terms of the steady state, transient performance, and parameter sensitivity. [ABSTRACT FROM AUTHOR]

To reduce the common-mode voltage (CMV) and eliminate the CMV spikes for two-level voltage source inverters (2L-VSIs), an improved model predictive control (MPC) based CMV reduction method is proposed in this paper considering dead-time effects. First, an improved voltage vector (VV) preselection strategy is proposed to reduce the CMV spikes caused by the dead time. Second, a new hybrid VV preselection strategy based on a delay compensation strategy and a modified current sector division strategy is proposed to completely eliminate the CMV spikes. As the proposed hybrid VV preselection based MPC strategy makes full use of the six nonzero VVs of the 2L-VSI, the current total harmonic distortions and ripples are reduced. The simulation and experiments are carried out to verify the effectiveness of the proposed strategy. [ABSTRACT FROM AUTHOR]

In this paper, a fixed switching frequency model predictive current controller is designed and implemented on a sensorless five-level packed U-cell (PUC5) inverter interfacing the utility. The predictive control methodology is based on a voltage vector generation technique for the cost function optimization by nullifying its derivative. The aim of the controller is to allow a fixed-frequency operation with no iterations while operating as a utility line current regulator. A pulsewidth modulator based on employing PUC5 redundant switching states fixes the PUC5 auxiliary dc bus capacitor voltage to its desired level with no necessity of a regulator; the overall technique reduces system complexity with less sensors and no loops in the predictive algorithm making it suitable for industrial applications. System discrete model is developed and experimental results verify the performance of the designed controller in making a fast response in regulating the grid current and balancing the capacitor voltage. [ABSTRACT FROM AUTHOR]

Recently, a few fault-tolerant control strategies have been proposed for T-type three-level inverters to improve the reliability of the inverter system. However, the neutral-point (NP) voltage oscillations suppression is never considered in the previous fault-tolerant control strategies. In order to suppress the NP voltage oscillations when open-circuit fault occurs to NP switches, this paper proposes two novel fault-tolerant control strategies named as improved two-level switching tolerant control and hybrid switching tolerant control (HS-TC). Both methods are implemented by adding an optimal time-offset to the three-phase turn-ontimes. The corresponding time-offset value of each method is simply calculated considering the phase current and dwell time of [O] state. Moreover, an NP voltage balancing algorithm to eliminate the dc deviation and a dc bias to further reduce the NP voltage oscillations are used in the HS-TC. The performance and comparison of the tolerant controls with respect to the NP voltage oscillations, current total harmonic distortion, and dynamic response are illustrated and analyzed through the simulation and experimental results. [ABSTRACT FROM AUTHOR]

In this paper, performances on two kinds of aggregated flyback microinverters are compared in aspect of harmonic resonances, which are controlled by current feedback control and peak current control. Based on the Norton models of flyback microinverters obtained by a small-signal modeling approach, potential harmonic resonances with the grid are analyzed. Following that, an impedance-based stability criterion is proposed, where the resonance frequency can be calculated and predicted based on the derived Norton models and the system admittance matrix of aggregated microinverters. After comprehensive analysis and comparisons, it is found that the peak-current-control-based flyback microinverters has better performance on damping the harmonic resonances than the current feedback controlled one. Simulations and experiments are carried out for verifying the effectiveness of the presented models and the correctness of the analysis results. [ABSTRACT FROM AUTHOR]

In this paper, a three-level quasi-switched boost T-type inverter (3L qSBT2I) is proposed. A new pulse-width modulated (PWM) control method is presented to reduce the inductor current ripple of the qSBT2 I. In the introduced PWM technique, the shoot-through duty cycle is maintained constant to keep the modulation index as high as possible. Then, the only control parameters of the qSBT2I are the duty cycles of the two additional switches. By controlling the duty cycles of the two additional switches, the voltage gain of the proposed qSBT2 I can be improved to a value larger than that of the conventional 3L impedance source inverters. The steady-state analysis, operating principles, and comparisons with the impedance source-based 3L inverters are presented. A 1-kW prototype is constructed to verify the operating principle of the 3L qSBT2I. An indirect dc-link voltage regulator and a capacitor voltage-balance controller are applied to the proposed qSBT2I. Simulation and experimental results are presented. [ABSTRACT FROM AUTHOR]

Microinverters operating into the single-phase grid from new energy source with low-voltage output face the challenges of efficiency bottleneck and twice-line-frequency variation. This paper proposed a multilevel inverter based on bridge modular switched-capacitor (BMSC) circuits with its superiority in conversion efficiency and power density. The topology is composed of dc–dc and dc–ac stages with independent control for each stage, aiming to improve system stability and simplify the control method. The BMSC dc–dc stage, which can be expanded to synthesize more levels, not only features multilevel voltage gain but also partially replaces the original bulk input capacitor and functions as an active energy buffer to enhance power-decoupling ability between dc and ac sides. In dc–ac stage, the control strategy of optimized unipolar frequency doubling sine-wave pulse width modulation is proposed to improve the quality of output waveform. Meanwhile, the multilevel voltage phase has been optimized to further reduce the power loss. Finally, a prototype has been built and tested. Associated with the simulation, the experimental results validate the practicability of these analyses. [ABSTRACT FROM PUBLISHER]

A new pulsewidth modulation (PWM) strategy which is an alternative approach of the discontinuous PWM (DPWM) for a three-level neutral-point-clamped (NPC) inverter is proposed in this paper. A three-level NPC inverter is completely mature and very well-established topology in high-power applications. However, the three-level NPC inverter has an inheritance problem of the neutral-point voltage unbalancing due to the split dc-link capacitors. This structure can cause large neutral-point voltage ripple. Furthermore, output currents of the three-level NPC inverter are distorted by the neutral-point voltage ripple. Therefore, the neutral-point voltage must be controlled. In this paper, a new DPWM method using two different offsets for the neutral-point ripple reduction is proposed and the effectiveness of the proposed DPWM method is verified by using the simulation and the experimental results. [ABSTRACT FROM PUBLISHER]

Connecting legs in parallel in a voltage source inverter is a way to increase the output current and, thus, its rated power. The connection can be made using either coupled or uncoupled inductors, and achieving an even contribution to the output current from all the legs is a crucial issue. Circulating currents produce additional losses and stress to the power devices of the converter. Therefore, they should be controlled and minimized. An efficient technique to attain such balance when coupled inductors are used is presented in this paper. The proposed technique can also be used when the inductors are uncoupled, since it is a particular case where the coupling coefficients are zero. This technique does not include proportional–integral controllers and does not require any parameter tuning either. The exact control action needed to reach current balance is straightforwardly calculated and applied. Experimental results are shown in this paper to verify the efficiency of the proposed balancing method. [ABSTRACT FROM PUBLISHER]

Exploiting the rich switching redundancies of the dual inverter, new hybrid pulsewidth-modulation (PWM) switching methods are proposed in this paper using the degree of freedom of operating the individual inverters independently, in addition to exercising the degree of freedom of controlling the switching action of the individual legs independently. Two voltage entities, namely, common-mode voltage (CMV) and differential-mode voltage are identified in the dual inverter, and all hybrid PWMs are envisaged aimed at reducing and also eliminating the CMV in it. The effects of such attempts on motor shaft voltage and also the motor bearing currents are presented in detail. Furthermore, bearing current profiles of an open-end winding induction motor are also presented with both conventional and hybrid PWMs proposed in this paper. Electric discharge machining discharge currents are completely eliminated with the use of all hybrid PWM methods proposed in this paper. In addition, implications of completely eliminating the CMV are also presented in this paper. All hybrid PWMs proposed in this paper are first simulated using MATLAB and are experimentally verified on a dual two-level inverter feeding a 1.1-kW 415-V 3- $\phi$ open-end winding induction motor drive. [ABSTRACT FROM PUBLISHER]

A two-motor drive, supplied by a five-leg inverter, is considered in this paper. The independent control of machines with full dc-bus voltage utilization is typically achieved using an existing pulsewidth modulation (PWM) technique in conjunction with field-oriented control, based on PI current control. However, model predictive control (MPC), based on a finite number of control inputs [finite-control-set MPC (FCS-MPC)], does not utilize a pulsewidth modulator. This paper introduces three FCS-MPC schemes for synchronous current control in this drive system. The first scheme uses all of the available switching states. The second and third schemes are aimed at reducing the computational burden and utilize a reduced set of voltage vectors and a duty ratio partitioning principle, respectively. Steady-state and transient performances are analyzed and compared both against each other and with respect to the field-oriented control based on PI controllers and PWM. All analyses are experimental and use the same experimental rig and test conditions. Comparison of the predictive schemes leads to the conclusion that the first two schemes have the fastest transient response. The third scheme has a much smaller current ripple while achieving perfect control decoupling between the machines and is of low computational complexity. Nevertheless, at approximately the same switching loss, the PI-PWM control yields the lowest current ripple but with slower electrical transient response. [ABSTRACT FROM PUBLISHER]

This paper presents an advanced space vector modulation (SVM) strategy for a three-to-five-phase indirect matrix converter (IMC) to reduce common-mode voltage (CMV) with enhanced output performance. By replacing zero and medium voltage vectors with large voltage vectors to synthesize desired output voltage, the five-phase inverter stage modulation can reduce the CMV peak value by 47%, compared with the conventional SVM. In order to compensate the degraded output performance due to the absence of the zero voltage vectors, the rectifier stage modulation is modified by utilizing the two-vector and three-vector modulation techniques. Consequently, by combining the modulations of the rectifier and inverter stages, the proposed modulation strategy can suppress the CMV, as well as improve the output performance of the three-to-five-phase IMC. Simulation and experimental results are provided to verify the effectiveness of the proposed modulation strategy. [ABSTRACT FROM PUBLISHER]

In this paper, the remedial operation of switch faults will be investigated comprehensively for T-type-three-level-inverter-fed dual three-phase motor drives. The open-circuit switch faults in multiple phase legs are discussed at first. The faulty conditions are classified into five categories. Different remedial strategies, namely Type-I to Type-V schemes, are proposed for different faulty conditions. In particular, three kinds of Type-III fault-tolerant control schemes are proposed by using medium-voltage vectors to synthesize small-voltage vectors, in such a way that the mid-point voltage in a dc link can be stabilized well. Then, the short-circuit faults in both clamping switches and half-bridge switches are investigated. By analysis, their operation conditions are equivalent to conditions loss of both P and N voltage levels and open-phase faults, respectively. Thus, the corresponding remedial strategies can be applied accordingly. Particularly, a voltage compensation control method is proposed for conditions, where open-switch faults coexist with open-phase operation induced by short-circuit faults in half-bridge switches. The validity of all of theoretical analysis and the proposed remedial strategies has been verified by experiments. [ABSTRACT FROM PUBLISHER]

This paper proposes the combination of a novel modified quasi-Z-source (MqZS) inverter with a single-phase symmetrical hybrid three-level inverter in order to boost the inverter three-level output voltage. The proposed single-phase MqZS hybrid three-level inverter provides a higher boost ability and reduces the number of inductors in the source impedance, compared with both the single-phase three-level neural-point clamped quasi-Z-source inverter and the single-phase quasi-Z-source cascaded multilevel inverter. Additionally, it can be extended to obtain the nine-level output voltage by cascading two three-level pulse width modulation switching cells with a separate MqZS and a dc source, which herein is called a single-phase MqZS cascaded hybrid five-level inverter (MqZS-CHI). A modified modulation technique based on an alternative phase opposition disposition scheme is suggested to effectively control the shoot-through state for boosting the dc-link voltage and balancing the two series capacitor voltages of the MqZS. The performances of both the proposed MqZS-CHI and the modulation techniques are verified through simulation and experimental results. [ABSTRACT FROM PUBLISHER]

This paper presents a nine-level active-neutral-point-clamped (ANPC) based multilevel inverter (MLI) topology for grid-connected applications requiring only ten switches. The envisaged structure comprises two parts, namely five-level ANPC unit, and a two-level converter leg whose midpoint is used as another ac terminal. An ad hoc switching state redundancy based modulation strategy is used to ensure that the voltage across the flying capacitor is tightly balanced and is implemented using a look-up table further simplifies the control complexity. The performance and effectiveness of the proposed topology with its control scheme are validated through simulations and experimental tests. Comparison with other MLIs is included to highlight the merits of the proposed topology. From the results, it will be shown that the proposed inverter requires the least part count as compared to other topologies with the same performance and output quality. [ABSTRACT FROM PUBLISHER]

Cascaded H-bridge (CHB) multilevel inverters (MLIs) have been widely used for power electronics systems. While high-voltage blocking across power switches is not a constraint for low voltage applications, the research trend has been oriented to the design of more compact module topologies as an alternative for CHB. Despite the generation of more voltage levels with reduced switch count, the existing module topologies in recent literature take no account of the freewheeling current path during dead-time, thus, inducing multistep jumps in voltage levels and giving rise to undesirable voltage spikes. Addressing this concern, this paper proposes two symmetrical compact-module topologies for cascaded MLI, where freewheeling current path during dead-time is provided for smooth transition between voltage levels to prevent voltage spikes. The proposed 7-level and 13-level compact-modules demonstrated low number of conducting switches for all voltage levels. Comprehensive analysis and comparison with the latest module topologies are conducted. To validate the operation of the proposed compact-module topologies, simulation and experimental results are presented. [ABSTRACT FROM PUBLISHER]

In this paper, a dc-link voltage protection (DCVP) control method is proposed to address the dc-link overvoltage issue due to power backfeeding in a parallel uninterruptible power supply (UPS) system. The proposed control method is able to protect the inverter against the excessive dc-link voltage, which increases the system reliability and robustness. Moreover, a current sharing control strategy is proposed by online regulating the virtual resistance of each UPS module. The proposed current sharing control strategy is able to address the circulating fundamental and harmonic currents caused by the line impedance mismatching or power backfeeding issue in the UPS system. In addition, an improved consensus-based distributed controller is proposed to alleviate the overshoot issue during the transient process in voltage amplitude and frequency restoration. Finally, the feasibility of the proposed methods is verified by experimental results from the parallel UPS prototypes. [ABSTRACT FROM PUBLISHER]

This paper aims to investigate a disturbance-rejection-based model predictive control (MPC) with two flexible modes (i.e., unconstrained mode and constrained mode) for three-phase inverters with an $LC$ filter. A disturbance observer (DOB) is designed to both simplify the prediction model and achieve the robustness against uncertain parameters. First, the unconstrained mode is designed with a simple horizon-one MPC control law to precisely regulate the output voltage in the steady state. Next, the constrained mode is designed with long-horizon MPC to quickly drive the system to the unconstrained mode by further optimizing the modulation stage. Also, the proposed MPC ensures the robustness and optimality in all operating modes. Especially, the overall closed-loop stability with DOB dynamics is proven by using Lyapunov function. Unlike other MPC methods, the long-horizon MPC in the constrained mode is specialized by finite switching sequences of the sector-based space vector modulation. Comparative studies with the conventional linear quadratic regulator are conducted on a prototype test bed with a TI TMS320F28335 DSP. Then, the proposed MPC method verifies fast dynamic response and advanced voltage regulation (i.e., small steady-state errors and low total harmonic distortion) under various load conditions and uncertain parameters. [ABSTRACT FROM AUTHOR]

Several applications such as power supplies for electric precipitators, ozone generation, partial discharge, etc., require ac superimposed dc (ACsDC) voltage supply. Most of such applications use intransigent systems for producing ACsDC voltages. In this paper, three different kinds of flexible power electronic converters are proposed for producing ACsDC voltages. These converters have two power conversion stages: input and output. In the input stage, two isolated dc voltages are obtained by using an isolated three-port dc–dc converter or two isolated two-port dc–dc converters. In the output stage, one of the input-stage dc voltages is used to generate an ac voltage and the obtained ac voltage is added to the remaining input-stage dc voltage to obtain an ACsDC voltage. Based on the converters used in the input stage, the proposed ACsDC converters are named as a dual active bridge (DAB) converter-based ACsDC converter (DAB-ACsDC), triple port active bridge (TAB) converter-based ACsDC converter (TAB-ACsDC), and dual transformer-based asymmetrical triple port active bridge (DT-ATAB) converter-based ACsDC converter (DTATAB-ACsDC). A detailed analysis of these ACsDC converters and their verifications using simulations and experimental studies are presented, which depict that the proposed converters can be used effectively for producing ACsDC voltages. [ABSTRACT FROM AUTHOR]

Compared with multilevel space vector modulation, level-shifted multicarrier sinusoidal pulsewidth modulation (SPWM) for nested neutral point-clamped (NNPC) inverters requires much less calculations and implementation efforts, but the existing conventional SPWM cannot suppress the severe flying-capacitor (FC) voltage ripples under low output-frequency conditions. In order to solve this problem, a multicarrier-based PWM strategy with complete voltage balance control (VBC) capacity is proposed in this paper. For NNPC inverters operating under low output-frequency conditions, two preprocessing steps, the zero-sequence injection and the modulation-signal rearrangement, are proposed before the comparisons between level-shifted carriers and modulating signals. These preprocessing steps make the average currents flowing through FCs zero, which is beneficial to greatly reduce the FC voltage ripples under low output-frequency conditions. Together with additional VBC, the proposed modulation can assure the FC voltages balanced under the entire output-frequency conditions. Principles and implementation processes of proposed modulation techniques and VBC methodsare elaborated in detail and compared with conventional modulation methods. Both simulation results from a 5-MVA system and experimental results based on a 5-kVA platform are presented to verify the effectiveness. [ABSTRACT FROM AUTHOR]

This paper proposes a high-efficiency two-stage three-level grid-connected photovoltaic (PV) inverter. The proposed two-stage inverter comprises a three-level step-up converter and a three-level inverter. The three-level step-up converter not only improves the power-conversion efficiency by lowering the voltage stress but also guarantees the balancing of the dc-link capacitor voltages using a simple control algorithm; it also enables the proposed inverter to satisfy the VDE 0126-1-1 standard of leakage current. The three-level inverter minimizes the overall power losses with zero reverse-recovery loss. Furthermore, it reduces harmonic distortion, the voltage ratings of the semiconductor device, and the electromagnetic interference by using a three-level circuit configuration; it also enables the use of small and low-cost filters. To control the grid current effectively, we have used a feed-forward nominal voltage compensator with a mode selector; this compensator improves the control environment by presetting the operating point. The proposed high-efficiency two-stage three-level grid-connected PV inverter overcomes the low efficiency problem of conventional two-stage inverters, and it provides high-power quality with maximum efficiency of 97.4%. Using a 3-kW prototype of the inverter, we have evaluated the performance of the model and proved its feasibility. [ABSTRACT FROM PUBLISHER]

In this paper, a new nonisolated high-voltage-gain boost converter is proposed. The proposed converter is constructed by adding an additional inductor to a conventional three-level-boost (TLB) converter. When compared with the conventional boost and TLB converters, the proposed converter can achieve higher voltage conversion ratio with reduced voltage and current stresses in the switches. In particular, the proposed converter can reduce the losses of active devices by reducing the current of the switch compared to conventional converters, thus, can achieve high efficiency. In addition, the proposed converter automatically balances the output voltages for an unbalanced load without the need for any additional control strategy or auxiliary circuit. A 2-kW prototype converter was built and tested to verify performances of the proposed converter. [ABSTRACT FROM PUBLISHER]

Grid-connected power conversion systems for renewable energy sources must fulfill several requirements, e.g., the high efficiency, the reduced cost and complexity, and, quite often, the boost capabilities that is usually achieved using a front-end dc–dc boost converter before the inversion stage, leading to a two-stage architecture. Meanwhile, single-stage power conversion systems, which perform the boosting operation within the inversion one, offer some potential advantages, in terms of reducing the complexity and the volume of the whole system. Among several proposed options, the split-source inverter (SSI) has been recently proposed by Abdelhakim et al. as an alternative option with some interesting features to the commonly used Z-source inverter. Taking into account that the SSI is controlled by a single parameter, i.e., its dc and ac sides are controlled by the modulation index, it is of paramount importance to investigate its control scheme in grid-connected mode, which has never been studied yet. Hence, this paper models the SSI dc side and proposes a modified modulation scheme combined with the commonly used synchronous reference frame control technique to achieve a decoupled control scheme of the SSI in grid-connected mode, i.e., the dc and the ac sides of the SSI can be controlled independently, which is convenient for many applications. The introduced control scheme is analyzed and simulated using a MATLAB/Simulink model, where a reduced scale 1-kVA grid-connected SSI is designed and simulated for the sake of experimental validation. Finally, the designed system is implemented experimentally to validate and verify the reported analysis and simulations. [ABSTRACT FROM PUBLISHER]

This paper presents the design and implementation of a simple neutral point potential (NPP) regulator for a three-level diode-clamped inverter employing a sine-triangle regulator in conjunction with a closed-loop controller with reduced switching losses. The regulator principle is based on adding a continuous variable offset voltage which regulates the midpoint potential of the dc bus. The novelty of the proposed NPP regulator is in the determination of the magnitude of variable offset voltage based upon the average value, peak-to-peak amplitude, total harmonic distortions, and third harmonic content in NPP. Aside from maintaining dc-bus voltage balance, the proposed regulator leads to a significant reduction in the voltage distortion at the NP, resulting in the reduction of the required dc-bus capacitance. It also reduces the switching losses of the inverter by inserting the “no-switching” zone within each half cycle of the fundamental voltage wave. Analytical, computer simulation, and experimental results verifying the approach are presented in this paper for various load power factor angles. [ABSTRACT FROM AUTHOR]

Neutral-point (NP)-clamped three-level inverter, which is a widely used topology of multilevel converters, suffers from the NP voltage drift as its main technical drawback. The nearest-three-virtual-vector (\NTV^2) modulation method can control the NP voltage balance for any load over the full range of inverter output voltage. However, compared with the nearest-three-vector (NTV) modulation method, \NTV^2 increases the switching frequency. This paper combines \NTV^2 with NTV, and the two methods are used alternately in a fundamental cycle. The duty-cycle coefficients of the redundant small vectors are analyzed to explore the intervals where NTV can control the NP voltage balance in a fundamental cycle. The proportional parameter, which represents the combination of the two methods in hybrid space vector pulsewidth modulation, can be selected to achieve a high-performance NP balance control and low switching frequency. The steady- and transient-state behaviors of the proposed strategy are analyzed in this paper. The experimental results verify the validity of the proposed strategy. [ABSTRACT FROM PUBLISHER]

In recent years, high photovoltaic array voltage up to 1000 V and transformerless grid-tied inverter have been increasingly researched and applied to elevate the inverter and the dc power collection efficiency. With the same reasons, a three-level neutral point clamped (3L-NPC) inverter featuring low power device voltage stress and low leakage current becomes increasingly attractive. In this paper, the operation and the features of a novel grid-tied 3L-NPC are presented. The proposed topology is a derivative of the three-level stacked neutral point clamped (3L-SNPC) structure. However, compared with the conventional 3L-SNPC and its pulse width modulation (PWM) strategy, the new topology with novel PWM strategy features completely inactive intrinsic body diodes. Furthermore, only two outer power devices are working with switching frequency, while the other four Insulated Gate Bipolar Transistors (IGBTs) are actually with the grid frequency. Therefore, the relatively high switching frequency is selected to reduce the inverter output filter inductance. A hybrid CoolMosfet and IGBT power module configuration is also proposed based on the new PWM strategy. The calculation shows that the total power device losses are reduced. The experimental results are illustrated in this paper to confirm the operation of the proposed topology and controller. [ABSTRACT FROM PUBLISHER]

In the paper by Chen et al. (IEEE Trans. Ind. Electron., vol. 66, no. 4, pp. 2837–2846, Apr. 2019), the authors proposed two fault-tolerant control strategies for T-type three-level inverters considering neutral-point (NP) voltage oscillations. However, some basic problems are worth being discussed about the proposed fault-tolerant control methods. This letter presents some comments and results concerning the paper by Chen et al. [ABSTRACT FROM AUTHOR]

In this paper, an immune algorithm (IA) is developed for optimization of the harmonic performance of a three-phase inverter under the space-vector pulsewidth-modulation (SVPWM) control strategy. The presented algorithm employs the immune approach as the search method for finding the best optimal control vectors and action time of the three-phase inverter. As a result, the optimal control vectors and action time are calculated to minimize the objective function of the weighted total harmonic distortion of the output voltage waveforms. In addition, an experimental platform based on DSP and field-programmable gate array is built. This paper provides a detailed performance analysis of the method with comparison to the conventional SVPWM. The simulation and experimental results verify the superiority of the best control sequences generated by IA compared with the existing conventional control strategies. [ABSTRACT FROM PUBLISHER]

A new pulse width modulation (PWM) strategy which is an alternative approach of the discontinuous PWM (DPWM) for a three-level neutral-point-clamped (NPC) inverter is developed and presented in this paper. The proposed PWM scheme not only takes advantage of the special properties available in NPC inverters, but also reduces the switching loss of the inverter along with an inherent neutral point (NP) voltage control. Based on a circuit-level decoupling concept, the NPC inverter can be decoupled into two three-level Buck converters in every defined operating section, and thereby the controller design can be simplified. The salient features of the proposed scheme, as compared with the existing carrier-based DPWM strategies, are: 1) its reduced computational processing time, 2) its capability to balance the dc-link voltage without any additional control, and 3) its reduced complexity, e.g., only one carrier wave needed for pulse width modulating. Same as a space-vector modulation, the maximum modulation index, 1.1547, can be attainable by the proposed scheme. Moreover, compared to conventional continuous sinusoidal PWM, using this technique proposed here, the switching losses of the devices can be reduced by one third. In order to explain the operation of this topology properly, the decoupling principle including the driving signal synthesis and the NP potential variation are analyzed in detail in this paper. Finally, the viability and performance of the proposed modulation scheme are shown through simulation and experimental results in a laboratory prototype. [ABSTRACT FROM PUBLISHER]

This paper presents a novel soft-switching galvanically isolated buck-boost dc–dc converter as a module-integrated converter for photovoltaic (PV) applications. It features three major operating modes: boost, normal, and buck mode. Their proper distribution over the input voltage range enables wide voltage regulation capabilities, i.e., close to those of nonisolated power optimizers. The proposed control algorithm requires only one buck-boost switching stage that performs voltage regulation by means of the switching stage reconfiguration with smooth transition between the modes. The design guidelines and the digital control system for PV applications are provided. The module-integrated converter was verified experimentally with a solar array simulator. The converter showed good maximum power point tracking performance and a peak efficiency of nearly 97%. [ABSTRACT FROM PUBLISHER]

This paper proposes a unique carrier-based pulse width modulation strategy for a three-level neutral-point-clamped inverter that works satisfactorily and with uniform convergence time over the full power factor (PF) range of the load variation. It has excellent control over capacitor voltages and mitigates low-frequency oscillations in the neutral point for the full PF range. First, an investigation is made to see how the load currents get modulated to generate compensating neutral current causing charging and discharging of dc-link capacitors. It is observed that when an additional modulating voltage signal that is in phase with the corresponding phase current is added in each phase, a neutral current is produced in the right direction which can be used to compensate for any prior unbalance in capacitor voltages. It is demonstrated that the performance of this scheme is insensitive to the load PF variation (full range from zero to unity). It performs satisfactorily throughout the entire linear modulation range and eliminates any undesirable low-frequency harmonic component in the compensating neutral current. The effectiveness of the proposed scheme is verified through simulation and experimental results by varying load PF as well as modulation index with both passive and motor loads. [ABSTRACT FROM PUBLISHER]

The high number of power semiconductors in multilevel converters makes them susceptible to failure. Therefore, one of the main concerns in utilizing multilevel inverters is their reliability. This paper proposes a new simple fault-diagnosis and fault-handling method to increase the robustness and reliability of a flying capacitor multilevel inverter (FCMLI) which is one of the most prominent multilevel inverters. The proposed method is capable of diagnosing failed switch(es) and reconfiguring the switching sequence such that the output voltage is maintained similar to a normal operation condition. The proposed scheme identifies failed switch(es) by using the information about the charging state of the capacitors and the applied switching sequence. After identifying the failed switch(es), the algorithm bypasses the failed switch(es) and converts the control signals of the faulty leg from an M -cell L-level configuration to an (M-F)-cell L -level configuration (where F is the number of failed switches). The most attractive feature of the proposed control scheme is that any number of failed switches can be tolerated, as long as the number of functional switches is higher than the minimum number of cells required to build a full-binary L-level FCMLI. Simulation and experimental results are presented that verify the effectiveness of the proposed method. [ABSTRACT FROM PUBLISHER]

In this paper, the near-state pulse width modulation (NSPWM), adapted to be used in dual-voltage source inverter (VSI) fed open-end load, is introduced primarily aiming to appreciably minimize the voltage total harmonic distortion (THD). Within the framework of the proposed method, the active time of pulses at the second inverter is relatively adjusted within switching interval (compared to the first VSI). The phase voltage harmonics are formulated for dual-inverter modulated by NSPWM; then, optimal adjustment is identified via a three-dimensional curve of phase voltage THD versus modulation index (MI) and phase angle displacement (PAD). Due to the limitation of MI in NSPWM, the desired output voltage is synthesized with modifying not only MI but also PAD between references of two VSIs. Furthermore, NSPWM inherently takes advantage of better efficiency compared to conventional space vector modulation due to switching only two phases within an interval (by clamping one phase to positive/negative dc-rail). The dual-VSI supplied by two isolated dc sources is assembled in the laboratory to experimentally evaluate the THD reduction feature of the proposed method; also, the simulation results obtained by means of a MATLAB/Simulink environment show close agreement with experimental data. [ABSTRACT FROM PUBLISHER]

This paper presents a sampled-time-domain analysis to investigate the sampling effect on instantaneous switching frequency of a digitally implemented hysteresis current control (HCC) in a voltage source inverter (VSI). The generalized expression of the instantaneous switching frequency with the consideration of sampling frequency has been derived. The effect of variation in sampling frequency on effective hysteresis band and switching frequency has been analyzed. The difference between maximum to minimum switching frequency of a fixed-band HCC VSI depends on the sampling frequency of the digital controller. The sampling also generates a steady-state tracking error exceeding the fixed-band limit at the fundamental frequency for fixed hysteresis band operation. The analysis has been done to achieve fixed switching frequency with variable hysteresis band and with varying sampling period. The frequency spectrum of the load current is presented to show the effect of a digital controller. The sampling effect on the switching performance has been demonstrated for a single-phase VSI under different loading conditions. To verify the analytical results, the simulation and experimental results are obtained with the current controller implemented on a field programmable gate array-based digital controller. [ABSTRACT FROM PUBLISHER]

In grid-connected inverters, a feedforward controller accurately compensates for a large number of the harmonic components of the injected current. This controller is fast and directly tackles the grid dynamic voltage disturbances without doing any further harmonic analysis. A feedforward controller was introduced to a three-phase grid connection with a wye configuration; however, for the widespread delta connections, such a scheme is less established. Moreover, the nonsinusoidal profile of the grid voltage waveform makes the online conversion of line-to-line values into phase values impossible. In this paper, implicit zero-sequence discontinuous pulse width modulation (IZDPWM) based feedforward control is implemented on the two-level grid-connected inverter. Regardless of the grid topology, the IZDPWM-based controller ensures sinusoidal current injection to the grid under balanced, unbalanced, and distorted conditions. [ABSTRACT FROM PUBLISHER]

A novel flying-capacitor-clamped five-level inverter based on bridge modular switched-capacitor topology is proposed in this paper. The inverter features the switched-capacitor circuit with dc–dc boosting conversion ability and the multilevel inverter circuit with flying-capacitor-clamped performance. With the special composite structure, the number of components is cut down compared to the topology of the conventional cascaded multilevel inverter. Meanwhile, part of switches can be operated under line voltage frequency, resulting in switching loss reduction. Hence, the potential of system efficiency and power density is released due to embed switched-capacitor circuit. More importantly, the optimized carrier-based phase disposition pulse width modulation method is employed as a control strategy. Under this control strategy, the capacitor voltage self-balance can be realized and quality of output waveforms can be improved significantly. After simulation, the prototype is built to validate the correctness and practicability of the analysis. [ABSTRACT FROM AUTHOR]

Compensation of nonlinear effects generated by dead-time and semiconductors voltage drop has been widely studied in the literature about two-level converters. This paper takes a closer look at those analyses for multilevel converters, specifically for a cascaded H-bridge (CHB) converter modulated with phase-shifted pulse width modulation. The interaction between the cells is analyzed for a generic $n$ -cell converter, from which a general expression for the distortion generated by the nonlinearities has been obtained. Based on this expression, a compensation signal for the overall converter is calculated on each sample time, which is a fraction of the triangular carrier used to modulate each cell, thus significantly improving the quality of the output voltage signals. Experimental validation of the proposed compensation method is presented using a three-phase four-cell CHB converter prototype of 5.5 kW. [ABSTRACT FROM AUTHOR]

This paper presents a closed-loop space vector modulation (SVM)-based sliding mode controller (SMC) for a three-level grid-connected neutral point clamped (3L-NPC) inverter. The nonlinear SMC based on Gao's reaching law has been designed to control the grid current and inject desired amount of active and reactive power into the network. Due to using single dc source at the NPC inverter dc bus, neutral point voltage is controlled through redundant switching states and instantaneous dc voltage feedback integrated into SVM technique. Meanwhile, there is no external voltage controller involved, thus no associated fine tuning issues are existed. The performance of the proposed hybrid controller to inject a desired active/reactive power to the grid is investigated through external perturbations such as change in the line current amplitude/phase shift, ac voltage fluctuation, as well as dc voltage variation. Full converter state-space model was developed and simulated. Experimental results are provided to verify the fast dynamic performance, low content of line current THD%, and good voltage balancing of dc bus capacitors of the NPC inverter. [ABSTRACT FROM AUTHOR]

This paper proposes a new configuration for static ground power unit (GPU) based on the novel 25-level hybrid active neutral-point-clamped (HANPC) converter. The superiority of the proposed converter, as compared with conventional and other suggested multilevel converters, is significant decreasing the number of switches and minimizing the number of flying capacitors (FC) in converter. This improvement is possible by using suggested low-voltage submodule converter to the ANPC converter and proposed modulation method. This results in reduction of the size and cost of converter and makes it more feasible and reliable. Applying the active voltage balancing method for FC in the proposed HANPC converter guaranties fast charging and voltage-level regulation of FC without using balance booster circuit. Improving output voltage spectrum leads to inductance reduction of output L–C filter which enhances static GPU performance. The simulation and experimental results verify the validity and feasibility of the proposed converter. [ABSTRACT FROM AUTHOR]

In this paper, a novel topology of six-level inverters for a medium-voltage high-power applications is proposed, which consists of inner flying-capacitor inverter (FCI) units and outer two-level inverter units. The proposed topology can reduce the number of devices, components, and isolated sources compared with the existing ones in the case of the same number of output voltage steps, which result in a reduction of the size and weight of the inverters. Also, the total power loss of the proposed topology is lower than that of the diode-clamped inverter (DCI) and FCI. Besides, the estimated cost of the proposed topology is about 60.5% and 81.3% compared with the DCI and FCI, respectively. In addition, the modulation technique and the control strategy for the dc-link capacitor and flying-capacitor voltages are developed for the proposed topology. The effectiveness of the proposed six-level inverter for the medium-voltage applications has been verified by simulation results. Also, the feasibility of the proposed inverter has been proved by experimental results for the prototype at the laboratory. [ABSTRACT FROM AUTHOR]