Search

A multi-level boost topology based on a flying capacitor is compared in this work with the hybrid, multi-level, partial power processing topology already presented in the literature for use as a highly efficient and compact dc/dc stage in 1500-V, two-stage, grid-connected PV systems. Different variations of the resonant stage of the hybrid topology are analyzed and compared in terms of losses, volume and complexity. Full multivariable optimization is conducted for the multi-level boost topology with different number of levels and for all the analyzed variations of the resonant stage of the hybrid topology. Appropriately rated new classes of 650-V and 900-V WBG devices are included in the optimization algorithm. It is concluded that due to the dominant conduction losses and gap in the voltage rating of the commercially available WBG devices between 650V and 200V, increase of the number of levels over 4 leads to the deteriorated loss and volume performances. All the analysis related to the resonant stage of the hybrid topology is confirmed by detailed and comprehensive measurements of two prototypes of 4kW of nominal and 7kW of maximal power. Additionally, all the loss models applied in the optimization algorithms presented in this paper are confirmed by detailed measurements, thermal calibration and finite element thermal simulations of the wide bandgap devices and inductor designs employed in this work. [ABSTRACT FROM AUTHOR]

With the rapid development of photovoltaic and fuel cell stacks, high voltage gain converters are urgently demanded. Conventional boost is limited by the exaggerated duty cycle, it is impossible to obtain a high voltage gain while ensuring efficiency. Therefore, a zero-voltage switching (ZVS)-modified SEPIC converter that combines a voltage multiplier cell with traditional SEPIC is proposed in this paper. With detailed parameters design process, this presented converter works at zero voltage switching (ZVS), while obtaining high voltage gain without extremely high duty cycle. Besides, voltage stress is also reduced and low-voltage component with lower parasitic parameters can be used, thus efficiency is maintained. In order to further improve the power density, an integrated inductor scheme is adopted in this paper without changing intrinsic working states of the two inductors. A 36-W prototype is built, and experiments are conducted to verify the advantages of the proposed converter. The efficiency is up to 91.5% at full load. [ABSTRACT FROM AUTHOR]

This paper proposes a soft-switched modulation technique with synchronous rectification for an isolated single-stage single-phase matrix-type dc–ac converter. The dc side consists of a full bridge inverter, and the ac side is a 2×2 matrix converter-based cycloconverter. The proposed unipolar modulation strategy provides zero current switching/zero voltage switching (ZVS) for the ac side devices and ZVS-on for the dc side devices. It also allows natural commutation of the current flowing through the secondary side leakage inductor of the isolation transformer and the grid inductor during unity power factor (UPF) condition, thus eliminates the requirement of snubber circuit. An improved soft-switched flyback-based regenerative snubber circuit is also presented for non-UPF operation. Proposed snubber circuit recycles the energy stored in the snubber capacitors in every switching cycle. A guideline to design snubber circuit along with a comparative study is discussed in this paper. Performance of the proposed hybrid modulation technique is evaluated in an SiC mosfet based 1.2-kW dc–ac converter prototype. A detailed analysis of the converter performance has been presented in this paper considering the circuit non-idealities. [ABSTRACT FROM AUTHOR]

A high-frequency high voltage gain discontinuous conduction mode coupled-inductor boost LED driver based on planar component is presented in this paper. GaN switch is adopted with lower conducting resistance and higher switching speed. Zero voltage switching (ZVS) is achieved at the same time to reduce high switching loss caused by high switching frequency. Compared with the previous work, the voltage gain is higher and efficiency is higher because of ZVS. This paper focuses on high efficiency; therefore, resonant gate driver is adopted and efficiency is increased by 0.6%. In terms of the coupled-inductor, planar component is used and parameter optimization is also proposed to realize lower loss, including wingding loss and fringing loss caused by the air gap. A 500 kHz 36 W prototype has been designed to demonstrate theoretical analysis. In addition, comparison of drive loss between the resonant gate driver used in this paper and conventional driver implemented by Si8271 is made, revealing advantages of the resonant driver. Obtained efficiency was up to 92.1% at full load. [ABSTRACT FROM AUTHOR]

The use of electronic equipment and other dc-compatible appliances in homes and offices is increasing at a very fast rate, as well as the distributed generation of energy. These two statements will most likely trigger, in a near future, the adoption of district-scale dc grids, connecting dc microgeneration plants and consumers, in an effort to cut the number of conversion steps required to deliver power to dc appliances. DC–DC converters will be fundamental in these systems, allowing the establishment of several voltage levels. The reliability of these converters plays a critical role, ensuring service continuity of the loads connected to them. With the increment of reliability in mind, this paper proposes a simple yet effective open-circuit fault diagnostic method suitable for interleaved dc–dc boost converters, but equally functional for other dc–dc converter topologies. The improvements introduced in this paper greatly simplify the diagnostic action, while making the correct diagnostic of faults independent of the switching duty cycle. Moreover, an alternative reconfiguration scheme is proposed to mitigate the adverse impacts of such faults. To prove the effectiveness of these strategies, a three-phase interleaved boost converter prototype was used in the experiments. [ABSTRACT FROM AUTHOR]

Multioutput converters with single input source are currently studied as an alternative to conventional dc–dc topologies in order to improve power density in low-power multiload applications. This paper reviews three different ways in which a boost topology can be customized to supply multiple outputs. The first way uses a charge-sharing approach using individual switches to distribute inductor energy to different capacitors. The second method of creating a multiport converter (MPC) combines two converters with similar front end to generate two outputs using only one controlled switch. Using this method, a boost converter can be combined with single–ended primary–inductor converter (SEPIC), Cuk, and current source converter topologies. The third method uses time multiplexing of switches to produce two regulated ports and is referred to as switched-boost action. This method uses relatively less number of switches and allows regulation and control of all the outputs. Practical utility of switched-boost action based MPC is reported in this paper. This switched-boost MPC is applied to a renewable power converter system to interface a solar panel, a battery, and home loads to produce a 12-V and a 48-V bus. The 12-V bus is interfaced to battery and capable of optimally charging the battery in constant current–constant voltage (CC-CV) mode. The converter is demonstrated to operate with solar panel as it supplies a 12-V battery and a 48-V load bus. When the solar power is not available, the converter automatically goes into a mode in which the 12-V battery supplies the loads on the 48-V bus. [ABSTRACT FROM AUTHOR]

This paper presents a study of the losses in the integrated buck–flyback converter (IBFC) used as high-power-factor LED driver. The aim of the study is to investigate the possibilities of increasing the efficiency of the IBFC converter. The procedure of the improvement is done by obtaining the equations of the current through each component in terms of converter parameters. The current is found in an average value or rms value, depending on the type of the parasitic component, whether it is modeled by a parasitic forward voltage source or by a parasitic resistance, respectively. Using these equations and the parasitic model, the losses of each element of the converter are estimated. This paper proposes a technique to increase the efficiency of the IBFC by redesigning the converter parameters. Furthermore, this paper presents a case of study with a step-by-step efficiency enhancement process of an existing driver. The driver is operating under universal input conditions, and 38 V output, supplying an LED luminary of 26.5 W. The new design shows an improvement of the efficiency from 82% in the old design to 89% in the proposed one. Moreover, the new design shows an improvement in the power factor and the THD and a 50% reduction in the output current ripple. Furthermore, a reduction in the number of components has been achieved, as it is found by the analysis that by adjusting the converter parameters, one diode can be removed. Finally, the presented methodology is explained in detail so that it can easily be applied to other dc–dc converters. [ABSTRACT FROM AUTHOR]

The pump-back test is widely adopted in the industry for characterizing and qualifying high-power converters. One popular pump-back test configuration is to tie the dc links of two converters together and circulate the current through the inductor connected between the ac terminals. In this configuration, one of the converters operates in the voltage mode to generate the virtual grid and the other converter regulates the circulating current, where hysteresis control could be applied. However, the switching characteristics of hysteresis control are unique due to the pulsewidth modulation type voltage being the virtual grid. This paper contributes to analyzing the switching frequency characteristics of the hysteresis control in this pump-back test configuration. The switching frequency tracking phenomenon is revealed and reported in this paper for the first time. Theoretical analysis, simulation validation, and experimental demonstration are provided to support the major conclusions. [ABSTRACT FROM AUTHOR]

This paper presents a single-stage nonisolated switched capacitor ac–dc converter for power-factor correction (PFC). This converter features reduced passive components, single switch, transformerless high voltage gain, and improves the power factor, reduces total harmonic distortion, and voltage stress across the switch. The peak current mode with a dynamic resonant perturbation scheme compensates the subharmonics that exist at zero crossing of the source current is implemented for PFC. In this paper, the principle of operation, large signal modeling of the circuit, and control method for the proposed PFC converter are provided. [ABSTRACT FROM PUBLISHER]

In this paper, it is described how the circulating current flows between inverters that have isolated dc link such as cascaded H-bridge (CHB) topology when they are operating in parallel. In this case, zero sequence circulating current, which normally flows through shared dc link, cannot flow between inverters in parallel. However, circulating current is provoked by asynchronous switching instant of devices, difference of dc-link voltages of parallel inverters, and unbalanced impedance. The circulating current should be suppressed by a sharing inductor that is inserted between inverters. Generally, all of the inverters should synthesize the same output voltage reference for load current control to minimize the size of this sharing reactor. However, this conventional method cannot guarantee diminishing circulating current in the transient state and even in the steady state. In this paper, in order to reduce sharing reactance, after deriving circulating current model from general case of n-parallel operation, circulating current control method is devised based on the model. This proposed algorithm is applied to active front end five-level-CHB inverter system for medium voltage drive. Simulation and experimental results are provided to verify the effectiveness of the proposed control scheme. [ABSTRACT FROM AUTHOR]

In this paper, an electric vehicle (EV) battery charger with interleaved Landsman converter (ILC) followed by a flyback converter, is designed and evaluated for improved power quality (PQ) charging of battery. A built-in wave-shaping is obtained at the charger front-end due to improved PQ characteristics of ILC. This PFC converter consists of two Landsman converter cells, which are designed in discontinuous conduction mode (DCM) to share the input and output currents. The current sharing at input results into lower input current ripple as well as peak current stress through the switch, is reduced. This, further improves the input current harmonics profile. Moreover, the reduced output voltage ripple gives reduced rms current in the output capacitor. A phase shift PWM scheme (PSPWM) is used for ILC and the duty cycle for the switches is selected below 50%. This allows the ripple cancellation at line and load sides. The interleaving at PFC stage as well as DCM based design ensures a low cost charging solution as compared to the conventional Landsman converter (CLC) based chargers in this power range. However, the flyback converter provides the current control during the charging of the battery in constant current (CC) and constant voltage (CV) regions. The harmonics spectrum of mains current follows the recommended PQ regulations over a range of varying line voltages and loadings. [ABSTRACT FROM AUTHOR]

This paper presents a new configuration of high gain (HG) single ended primary inductor converter (SEPIC) with a ripple-free input current to maximize the efficiency of the PV panel for standalone water pumping system (WPS). The ripple eliminating circuit combined with the HG SEPIC converter to achieve reduced ripples in photovoltaic (PV) current is independent to the duty cycle control and hence, it can be easily integrated to the main power circuit of configuration. This circuit does not need any active switches, control, or drive circuit for its execution. The ripple eliminating circuit yields a complete removal of the electrolytic capacitor connected across the PV array and significantly reduces the inductance of the HG SEPIC converter. It also improves the response and power density of the dc–dc converter. The large gain of dc–dc converter enables the use of low-voltage PV panel and minimizes the partial shading and parasitic capacitance effects on PV array source. Due to the substantial compatibility between natural characteristics of switched reluctance motor (SRM) drive and WPS, a four-phase SRM drive is utilized in the proposed scheme. In addition, a single current sensor based maximum power point tracking technique is utilized in the proposed system, which helps to reduce the cost and improve the accuracy of the overall system. Analytical, simulated, and experimental results of the developed system are presented to demonstrate the performance of the system. [ABSTRACT FROM AUTHOR]

A modular quasi-resonant bidirectional dc–dc converter composed of half-bridge gallium nitride modules (HBGM) with reduced switch voltage stress is proposed in this paper. By using an auxiliary capacitor, a resonant circuit is formed to shape the current and voltage so that zero-voltage switching at turn-on instant is achieved. Since the switching loss dominates the power losses in a high-frequency dc–dc converter, the soft-switching performance leads to a noticeable reduction in the total loss; so, the operating temperature will decrease, and consequently, size of the heatsink will be reduced. The proposed circuit takes advantage of enhancement-mode gallium nitride (eGaN) switches regarding their small on-resistance RDS(on), low gate charge, and fast switching speed to improve both efficiency and power density. The main performance issue of adopting GaN switches in a bidirectional dc–dc converter is the high voltage stress of GaN devices, which is handled by connecting the HBGM in the active-clamped stacked configuration, as well as optimizing printed circuit board layout design. Finally, a 1 kW, 600 V laboratory prototype operating at 100 kHz is implemented to validate the proposed concept. [ABSTRACT FROM AUTHOR]

Unipolar-pulsewidth modulation (UP-PWM) inverter takes advantages of high power efficiency and small output chokes which is widely used in the industry. However, UP-PWM inverters cannot be used in parallel operation due to a current unbalance problem. This paper studies the current unbalance problem of paralleled UP-PWM inverters with common dc bus and ac bus. First, the problem of unbalanced inductor current is defined and analyzed. Second, a technique to eliminate unbalanced currents is proposed. The proposed current balancing technique only requires one more current sensor in an inverter module rather than changing converter topology or modulation method, which makes it possible to apply UP-PWM inverters in parallel-operation while keeping the advantages of unipolar switching. The proposed current balancing method is verified by both simulation and hardware experiment. Experimental verification is performed on two 1 kW, 400 V input, and 120 V/60 Hz output prototypes, which shows a good agreement to the analytical study. [ABSTRACT FROM AUTHOR]

DC microgrid is gaining attraction and a recent trend in distribution power generation system due to penetration of renewables (especially photovoltaic or fuel cell). In this paper, a new triple-switch-triple-mode high step-up converter (TSTM-HS converter) is presented for dc microgrid applications. In the proposed converter, voltage lift technique is employed and range of duty cycle is extended by incorporating an additional switch in converter circuitry. By doing this, high voltage conversion ratio is achieved without using a transformer, coupled inductor, and multiple stages of switched capacitors. Moreover, the TSTM-HS converter operated in three modes with two types of the duty cycles to achieve low to high voltage conversion without using high duty cycle for each switch. The effects of difference in the inductance values on the regulation and operating behavior of the TSTM-HS converter are discussed. The continuous conduction mode and discontinuous conduction mode characteristics of the TSTM-HS converter are discussed in detail with steady-state analysis and boundary condition. The comparison is provided to highlight the benefits of the TSTM-HS converter. The selection of semiconductor devices and the design of reactive components are discussed for the TSTM-HS converter. The experimental results of the proposed converter are provided which validate the theoretical approach, performance, and feasibility of converter. [ABSTRACT FROM AUTHOR]

Parallel interleaved two-level (2L) three-phase voltage source inverters (VSIs) are widely used due to their distinct advantages of high power delivery, modularity, low current rating devices, etc. Along with these advantages, the parallel interleaved 2L VSIs could also be analyzed as a single three-level (3L) VSI. Conventionally parallel interleaved 2L VSIs are modulated using the 2L pulsewidth modulation (PWM) techniques. However, implementation of parallel interleaved 2L VSIs using the 2L PWM techniques may generate a higher ac side current ripple as compared to implementing the parallel interleaved 2L VSIs using 3L PWM techniques. This paper proposes a carrier-based method for implementing different 3L discontinuous PWM (DPWM) techniques for parallel interleaved 2L three-phase VSIs. Comparison of different 2L switching sequences for implementing a 3L DPWM switching sequence based on circulating current, line current ripple, and switching loss is also carried out. Simulation and experimental results are also displayed to validate the proposal. [ABSTRACT FROM AUTHOR]

An improved bridgeless (BL) Cuk converter-based electric vehicle (EV) battery charger with high power factor and increased efficiency is designed and developed in this paper. It provides low cost and high-power-density-based charging solution for the EV. This charger incorporates less number of devices operating over one switching cycle, which reduces the additional conduction loss incurred by a diode bridge rectifier of the conventional charger. Hence, it improves the charger's efficiency. The added advantage of the proposed topology is that the unwanted capacitive coupling loop is removed, as well as the unwanted conduction through the body diode of the inactive switch in the previously developed BL Cuk converter is avoided. This significantly improves the charger's efficiency. For the constant current and constant voltage charging, the commands are synchronized by a flyback converter. The proposed charger draws a sinusoidal current from ac mains and the total harmonic distortion in the supply current is reduced to the limits specified by the IEC 61000-3-2 guidelines. The improved efficiency and power quality indices of the proposed charger are investigated to demonstrate its satisfactory charging operation at all operating conditions. [ABSTRACT FROM AUTHOR]

Usually, the high-gain high-efficiency dc–dc converters consist of many passive components, which increases the order of the system. As the order increases, system modeling and control become more complex. Thus, there is a need for the simplification of the small signal modeling process of such converters. This paper presents a generalized small signal model and equivalent circuit for an $n$ th-order coupled-inductor-based high-voltage gain converters (CIHVGC) that can be conveniently used for the control design. The state variable representation of a generalized coupled inductor with p windings is included. A simplified step by step procedure to obtain small signal model using visual inspection is presented. Analysis is included and verified using simulations and experiments for the output voltage regulation of high-voltage gain converters. The usefulness and versatility of the proposed model is verified with three examples of high gain converters belonging to the CIHVGC family. All the analytical, simulation, and experimental details of this paper are presented. [ABSTRACT FROM AUTHOR]

This paper proposes a novel single-switch dc/dc converter for the future renewable electric energy delivery and management system to implement the distributed renewable energy resources (DRER). The DRER is responsible for the maximum power point tracking of the photovoltaic panel (PV) module and also for the control of central energy storage device. Due to the characteristics of the PV module and the dc-bus, the single power stage must provide low current ripple in the input and output terminals, must operate with output current and voltage regulation, and present a high-voltage conversion ratio. To achieve such features, this paper proposes a novel integrated Boost–Zeta converter. To avoid a complex modeling and control, we propose a disaggregation concept for this. Experimental results are presented for the purpose of operating the converter and also for the operation of the system. [ABSTRACT FROM PUBLISHER]

Compared with the conventional hard switching battery equalizers, hierarchical battery equalizer based on the bipolar continuous-conduction mode buck–boost units could effectively reduce the switching loss and improve the conversion efficiency. This paper mainly addresses the key technical challenges associated with the optimal design of this battery equalizer. The inductor current is controlled to enter into the negative region. Thus, the mosfet body diode provides a freewheeling path for the inductor current during the dead band. This ensures zero-voltage switching turn-on of both power mosfets in each buck–boost unit without auxiliary snubbers. Therefore, the switching losses are significantly reduced. Meanwhile, the integral of the inductor negative current is precisely controlled to minimize the circulating current. This guarantees both minimized conduction losses and suitable equalization speed. Furthermore, an equalization algorithm, which compensates the battery internal resistance induced state-of-charge error, is proposed to improve the equalization accuracy. The operating principles and design considerations are analyzed in detail. An experimental prototype to balance four series-connected lithium-ion battery cells is implemented. The experimental results validate the design of the equalizer and demonstrate obvious efficiency enhancement over the conventional method. [ABSTRACT FROM AUTHOR]

This paper introduces a three-phase grid-connected inverter for commercial-scale photovoltaic systems. The circuit topology combines an ac-inductor-less active bridge with a parallel-connected pulsewidth modulation inverter acting as an instantaneous reactive power compensator. The active bridge, called a 120° conduction inverter, operates at a switching frequency equal to the grid frequency and outputs a 120° rectangular current, while the compensator eliminates the harmonic currents included in the rectangular current. The main advantage of this strategy is the reduction in size of the required ac inductor by a factor of 4, as well as the reduction of power losses in the switching devices. The theoretical analysis clearly shows that the compensator can synthesize a sinusoidal output current by controlling only instantaneous reactive power, thus eliminating the need for electrolytic capacitors. A 5-kW experimental setup validates the operating principle and the control method of the proposed inverter and exhibits an inverter efficiency as high as 99.2% with Si superjunction mosfets. [ABSTRACT FROM AUTHOR]

This paper proposes a switching strategy for the Z-source inverter (ZSI), which has unequal short-through intervals to reduce the current ripple in the inductor of its impedance source. A size reduction of the inductor of the ZSI is one of the important issues in improving the power density of the ZSI, and the inductor current ripple reduction is required to achieve it. The proposed method can reduce the inductor current ripple by 27.8% compared with the conventional method that has equal short-through intervals without increasing the number of inverter switching. The proposed operation and ripple reduction were confirmed in experiments with a 3-kW-class laboratory prototype. Its result agreed to the calculated results, and it was confirmed that there is no increase in circuit losses caused by the application of the proposed method. [ABSTRACT FROM AUTHOR]

The utilization of wide band gap devices has enabled high frequency operation of totem pole bridgeless PFC rectifier. However, most of the designs reported in the literature with frequency higher than 100 kHz operate under discontinuous conduction mode or critical mode to reduce the switching loss. This paper proposes a zero-voltage-transition (ZVT) technique for totem-pole PFC rectifier under continuous conduction mode operation which enables efficient operation at switching frequencies well above 100 kHz. A simple auxiliary circuit consisting of a small auxiliary inductor and two active switches is placed in parallel with the main input filter inductor to achieve zero-voltage-switching of the main switches. The auxiliary switches operate with zero-current-switching (ZCS) and conduct current as short resonant pulses only during the critical turn-on transition which results in very low losses in the auxiliary circuit. The timing of the auxiliary switches is adaptively controlled with respect to the grid voltage angle for optimized overall efficiency. The effectiveness of the proposed ZVT scheme has been validated through experiments based on a 2.4 kW 400 kHz hardware prototype with 98.35% peak efficiency. [ABSTRACT FROM AUTHOR]

A switching-capacitor-based buck–boost converter (with common ground) for point of load applications is proposed in this paper. It is capable of operating in stand-alone buck or boost mode in addition to its primary operation of performing the buck–boost conversion. The striking feature of the proposed converter is low source current ripple content irrespective of its mode of operation (buck–boost, buck, or boost). First, feasible pulsewidth modulation schemes for the proposed converter are identified and thereafter the corresponding circuit performance analysis, steady-state analysis, and state-space modelling is established. Through steady-state analysis, voltage gain expressions are formulated and equations defining L-C components are derived in terms of their ripple quantities. The state-space models are used to formulate small-signal analysis and to obtain the relevant transfer functions required in the controller design. A voltage-mode/current-mode controller is designed, with a tradeoff in bandwidth, to control the proposed converter and transit it from buck to boost mode or vice versa seamlessly. A 30–55 W, 100 kHz, prototype point of load converter with 36-V input dc source is built to supply power at constant load voltage of either 48 or 28 V. The proposed converters’ effectiveness is demonstrated experimentally in terms of reduced source current ripple along with seamless transition from buck to boost mode and vice versa. [ABSTRACT FROM AUTHOR]

In this paper, a fifth-order boost point-of-load converter is developed by cascading a modified fourth-order boost converter with a combination of L–C and diode. This topology has the following salient features: Single-switch topology, common ground between source and load, low-voltage stress across intermediate capacitors, and voltage gain same as other reported fifth-order boost converters with no common ground. Steady-state and dynamic analyses demonstrate the proposed converter's boosting feature and dynamic performance, respectively. A contoured robust Bode plot methodology is employed to design the robust voltage-mode controller to ensure load voltage regulation in the presence of uncertainties. The necessary and sufficient conditions under which the designed controller guarantees the load voltage regulation and robust stability are obtained. A step-by-step robust controller design procedure is outlined. The salient features of the proposed converter and its robust performance are studied analytically, using the MATLAB platform, and validated experimentally on a 60-W prototype module. [ABSTRACT FROM AUTHOR]

This paper presents a dual output power factor correction (PFC) converter for switched reluctance motor (SRM) drives. Here, a modified single-ended primary inductance converter (SEPIC) is proposed for a wide range of speed control and to achieve PFC at ac mains. The switching frequency of the converter is considered to be 20 kHz. The converter is designed to operate in the discontinuous conduction mode (DCM) of operation, which reduces the size of the output inductor. The DCM mode to obtain PFC also reduces the sensor requirement as compared to the continuous conduction mode (CCM), where two voltage sensors and one current sensor add to the drive cost. The drive is proposed for universal ac mains (90–270 V ac). Simulated and experimental results are demonstrated to validate the performance of the drive during different operating conditions. The input current total harmonic distortion is reduced to comply with an IEC 61000-3-2 standard. [ABSTRACT FROM AUTHOR]

This paper presents a step in microlevel photovoltaic (PV) summation technology for combining unsymmetrical PV modules with differences in specification and age, relocation on nonfertile land, or multilocation mounting by designing an add-on modular hardware interface to a multi-input single-output (MISO) dc bus, using an MISO controller employing a suitable maximum power point (MPP) tracker under partial shading/long distance/mismatching PV module conditions along with a sensor-less PV vector control inverter (PV–VCI) driving a three-phase asynchronous squirrel cage induction motor dedicated to irrigation, with the facility of autoconfiguration/autotuning at the beginning. A PV source gets automatically added/removed in a ramp profile in proportion to the load in steps, thus keeping on only when required, enabling high efficiency, minimum heating, and prolonged life as that of a PV module. The contribution includes a reduced PV energy cost per watt by 24.10%, improved return on investment by 27.48%, improved water discharge yield by 11.06%, and improved MPP tracker impact by 14.59% with 90.88% MISO system efficiency compared to a normal scheme. [ABSTRACT FROM AUTHOR]

Flyback/forward derived power converters offer operational simplicity, but require active clamping circuits to reduce switch voltage stress and improve the converter efficiency. This paper presents an active clamping circuit technique, which additionally ensures enhancement in the converter voltage gain. This is enabled by the proposed auxiliary circuit, which introduces a charged capacitor in series with the primary source during the energizing interval. Two circuits are designed on this principle, and design and operation of both are presented for discontinuous conduction modes. It is shown that the voltage gain of these circuits increases with increase in the leakage inductance, which is an improvement over existing converters. Also, in one circuit primary (secondary) winding, rms current is similar to (lower than) that in a typical ideal flyback converter, leading to improvement in power density. Operation and analyses of this variant are experimentally verified with a 400-V laboratory prototype. [ABSTRACT FROM AUTHOR]

This paper investigates a multilevel inverter composed of series/parallel-connected H-bridges. The presented structure can be used for applications in which the use of semiconductor switches with low-voltage and low-current ratings is intended. A comprehensive system model, an overall control strategy to adjust the output voltage with constant magnitude and frequency, and a level-shifted PWM (LS-PWM) strategy based on a voltage vectors unidimensional analysis and a plane analysis are presented. The LS-PWM is capable of mitigating the low-frequency circulating current, thus generating multilevel voltage signals with low harmonic distortion, maximum number of levels, and low dv/dt. In addition, considering a wide range of values of voltages and currents and various power levels, the total converter losses are reduced compared with the conventional multilevel converters. Two multilevel conventional inverters with the same number of semiconductor switches are used for comparison. Simulation and experimental results demonstrate the feasibility of the studied converter. [ABSTRACT FROM AUTHOR]

Pollution problems caused by fossil fuels have led to more investigations on renewable energy systems. Photovoltaic cells and fuel cells output low-level voltage than required; therefore, high gain dc–dc converters are used to boost this low voltage. The Z-source converter can be employed as dc–dc converter to boost the photovoltaic panel voltages. It also offers other advantages, such as clamped switched voltage, high voltage gain, isolation of energy source from the load, and positive polarity for output voltage; therefore, this is a good choice for high step-up applications. This paper presents analysis of a novel high step-up Z-source based dc–dc converter that has higher voltage gain than the Z-source converter. Furthermore, high efficiency, low device voltage stress, and wide voltage gain range make it a good candidate for photovoltaic and high voltage step-up applications. The proposed dc–dc converter is evaluated experimentally for converting 24-V dc input to 300-V dc output at 100 W and to validate the simulation results. [ABSTRACT FROM AUTHOR]

This paper proposes a multilevel flying capacitor dc/dc boost converter (FCBC) with a small capacitance of the flying capacitor for the reduction of converter size. In this paper, the design methods for the boost inductor and the flying capacitor in the n-level FCBC are principally and experimentally confirmed. Furthermore, the boost inductor is designed based on maximum product of voltage-time, regardless the number of level. Meanwhile, the minimum capacitance of the flying capacitor is designed based on the maximum switching device voltage stress, regardless of the output voltage ripple influences. Moreover, the achieved maximum efficiency of the designed three-level FCBC is 98.5% at the output power of 1 kW. Finally, the effectiveness of small capacitances of the flying capacitor in the three-level and five-level FCBCs is analyzed. The characteristics of the distorted voltage across the input voltage source and the boost inductor, and the distorted current to the output side (output capacitor and load) are investigated with several capacitances of the flying capacitors in the three-level and five-level FCBCs. As a result, it is experimentally confirmed that the distorted voltage is drastically reduced by increasing the number of level. Besides, the distorted current is almost the same although the number of level is increased. Therefore, based on the experimental results, it is shown that small capacitance of the flying capacitor can be used in the n-level FCBC without compromising the stability of converter operation. [ABSTRACT FROM PUBLISHER]

Parallel ac-link universal power converters are a relatively new class of power converters that can be configured as dc–dc, dc–ac, ac–dc, and ac–ac. These converters are extensions of a buck–boost converter in which the current of the inductor is alternating and the input and output can have any number of phases with any forms, voltage amplitude, or frequency. By placing a small capacitor in parallel with the link inductor, all the switches can benefit from soft switching. The main limitation of the parallel ac-link universal power converter is its large number of switches. A three-phase ac–ac configuration requires 24 unidirectional switches. This paper proposes two topologies based on the parallel ac-link universal power converters that significantly reduce the number of switches. One of the proposed topologies reduces the number of switches in a three-phase ac–ac configuration to 16. The other topology reduces the number of switches to 10. The latter can offer galvanic isolation with only a single-phase high-frequency transformer. This paper presents the principles of the operation of the proposed topologies and evaluates them through simulation and experiments. [ABSTRACT FROM AUTHOR]

This paper proposes a single-stage single-switch light-emitting diode (LED) driver that integrates a buck–boost circuit with a Class-E resonant converter by sharing single-switch device. The buck–boost circuit, working as a power-factor correction (PFC) stage, operates in the discontinuous conduction mode (DCM) to shape the input current. The Class-E converter steps down the voltage to drive the LED. For specific component parameters, the Class-E converter can achieve soft-switching on the power switch and two rectifier diodes, and reduce switch losses at high frequencies. Electrolytic capacitors are used in the proposed converter to achieve a lower cost, but the system reliability decreases. To overcome this disadvantage, film capacitors can be used, but the current ripple increases. Neglecting the cost, multilayered film capacitors are the best option, if higher reliability and lower current ripple are required. The proposed driver features high efficiency (90.8%), and a high power factor (PF) (0.995). In this paper, analytical results and design considerations at 100 kHz are presented, and a 100-W prototype with 110 \textV\text{AC} input was built to validate the theoretical analysis. [ABSTRACT FROM AUTHOR]

A dual active bridge (DAB) converter promises high power density. The highest power transfer can be achieved by phase shift modulation inside the zero-voltage switching boundaries. This paper analyzes the transients of DAB commutation. Although commutation has been previously analyzed for DAB with the linear turn-off snubbers, in today's industries, the output capacitors of the switches are utilized as the snubberless approach. The presence of these time-variant capacitors leads to nonlinear equations. This paper applies a piecewise linear model for analyzing the commutation of the ac-link current into the switches. The study is inspired by practical experiments, and the results are experimentally verified. [ABSTRACT FROM PUBLISHER]

A single-phase bridgeless Cuk ac/dc power factor correction (PFC) rectifier with positive output voltage is proposed in this paper. For low output voltage product applications, the rectifier is designed to convert high input voltage to low output voltage. Due to no bridge diodes required and thus decreased input conduction losses, the proposed rectifier efficiency can be improved. The proposed rectifier operates in discontinuous conduction mode, and the current-loop circuit is hence not needed. In addition, only a single switch is used in the rectifier to simplify the control circuit design. A simple translation method to have the positive output voltage in the Cuk converter is presented in the rectifier to reduce the component counts and the cost. The operational principles, steady-state analysis, and design procedure of the proposed rectifier are addressed in detail in this paper. Simulation and experimental results obtained from a 150-W rated prototype circuit with input of 90–130 Vrms, 60 Hz, and output of 48 Vdc have verified the validity of the proposed rectifier. [ABSTRACT FROM PUBLISHER]

This paper proposes a novel bidirectional inverter, named series ac-link inverter. This three-phase inverter belongs to a new class of partial resonant ac-link converters in which the link is formed by a series ac inductor/capacitor (LC) pair having low reactive ratings. The input and output of this converter can be either dc, ac, single-phase, or multiphase. Therefore, they can appear as dc–dc, dc–ac, ac–dc, and ac–ac configurations. In all of these configurations, the ac capacitor is the main energy-storage element, and the inductor is merely added to facilitate the zero-current turnoff of the switches and their soft turn-on. Due to the zero-current turnoff of the switches in the proposed converter, the use of SCRs with natural commutation is possible as well. Since the current and voltage of the link are both alternating, no bulky dc-electrolytic capacitors are required in this converter. This paper mainly focuses on bidirectional dc to three-phase ac conversion. This single-stage inverter can step up or step down the voltage in a wide range. If galvanic isolation is required a single-phase high-frequency transformer can be added to the link. In the proposed inverter, the power can flow in both directions, and therefore, it is an excellent candidate for battery-utility interface and electric vehicle applications. In this paper, the principles of the operation of the proposed inverter, along with its design and analysis, are studied. Moreover, the performance of the proposed configuration is evaluated in this paper. Both simulation and experimental results are included. [ABSTRACT FROM AUTHOR]

This paper proposes a new circuit configuration and a control scheme for a single-phase current-source inverter with a power decoupling circuit which is called as the active buffer. The proposed inverter achieves a low-dc-input voltage ripple and also provides a sinusoidal current that can achieve unity power factor, without large passive components in the dc bus such as smoothing inductors and electrolytic capacitors. These components are conventionally required in order to decouple the power pulsation caused by the single-phase power source. In this paper, the fundamental operations of the proposed inverter are demonstrated experimentally. From the experimental results, the input voltage ripple is 8.87%, and the output current total harmonic distortion is 4.24%. In addition, an output power factor of 99% and a maximum efficiency of 94.9% are obtained. Finally, it is confirmed that the maximum power densities of the conventional circuit and the proposed circuit are 2.75 kW/L at the switching frequency of 70 kHz and 4.86 kW/L at the switching frequency of 80 kHz, respectively. [ABSTRACT FROM AUTHOR]

Soft-switching ac-link universal power converters, also called partial resonant converters and ac-link buck–boost converters, have received noticeable attention during the last few years. In these converters, each of the inputs and outputs can be dc, single-phase ac, or multiphase ac; therefore, they can be used for dc–dc, dc–ac, ac–dc, or ac–ac power conversion systems. The soft-switching ac-link universal power converters are compact, reliable, and expected to offer longer lifetime compared with the other types of converters. However, they require more switches, which make the control process more involved. The sparse ac-link buck–boost converters were proposed to partially solve this problem. The sparse configuration reduces the number of switches from 24 to 20 in a three-phase ac–ac configuration. This paper proposes a modified configuration, which further reduces the number of switches without changing the principles of operation. This converter, which is named ultrasparse ac-link buck–boost converter, reduces the number of switches from 24 to 16, in a three-phase ac-to-ac case, and from 20 to 10, in a dc-to-three-phase-ac configuration. The proposed converter is applicable to systems with unidirectional flow of power, such as PV and wind power generation systems. This converter is expected to offer higher reliability compared with the original converter and higher reliability and efficiency compared with the sparse configuration. Another important feature of this configuration is that it can be fabricated by insulated-gate bipolar transistor modules, which are more compact and more cost effective compared with discrete devices. This paper presents the principles of the operation of this configuration and compares the efficiency, the failure rate, and the current rating of the switches in the ultrasparse, sparse, and original configurations. Moreover, it evaluates the performance of the proposed converter through simulation and experiment. [ABSTRACT FROM AUTHOR]

This paper presents a novel dc–dc converter configuration, which successfully integrates two technologies, including a switched capacitor and a switched coupled inductor, into one converter. By adopting a coupled inductor to charge a switched capacitor, the voltage gain can be effectively increased, and the turns ratio of the coupled inductor can be also reduced. Not only lower conduction losses but also higher power conversion efficiency is benefited from a lower part count and lower turns ratios. The proposed converter is simply composed of six components, which can be further derived to varied converters for different purposes, such as a bidirectional converter. The operating principle and steady-state analysis are discussed in this paper. A 250-W laboratory hardware prototype is completed and verified. The voltage gain is up to 11. The highest efficiency is 97.2%, and the full-load efficiency is kept at 93.6%. [ABSTRACT FROM AUTHOR]

This paper proposes a single-stage high-power-factor (HPF) LED driver with coupled inductors for street-lighting applications. The presented LED driver integrates a dual buck–boost power-factor-correction (PFC) ac–dc converter with coupled inductors and a half-bridge-type $LLC$ dc–dc resonant converter into a single-stage-conversion circuit topology. The coupled inductors inside the dual buck–boost converter subcircuit are designed to be operated in the discontinuous-conduction mode for obtaining high power-factor (PF). The half-bridge-type $LLC$ resonant converter is designed for achieving soft-switching on two power switches and output rectifier diodes, in order to reduce their switching losses. This paper develops and implements a cost-effective driver for powering a 144-W-rated LED street-lighting module with input utility-line voltage ranging from 100 to 120 V. The tested prototype yields satisfying experimental results, including high circuit efficiency ( $>$ 89.5%), low input-current total-harmonic distortion ( $<$ 5.5%), high PF ( $>$ 0.99), low output-voltage ripple ( $<$ 7.5%), and low output-current ripple ( $<$ 5%), thus demonstrating the feasibility of the proposed LED driver. [ABSTRACT FROM PUBLISHER]

Paralleled inverters are not only a suitable approach to increase the power capacity, but also have the capability of common mode voltage (CMV) reduction, or even elimination. The original zero CMV modulation scheme for paralleled inverters suffers from the current jump problem in phase-leg currents. This current jump phenomenon amplifies the peak values of differential-mode circulating current (DMCC) and zero-sequence circulating current (ZSCC), which is adverse for the design of coupled inductor and common-mode inductor. This paper introduces the modified modulation scheme, which can keep volt-seconds balance in whole fundamental period and mitigate the current jump in phase-leg currents. In addition, the reduction effect of the DMCC and ZSCC can be achieved. To verify the analysis, both the simulation and experimental results are presented, which validates the proposed methods and show that they are beneficial for DMCC and ZSCC reduction. [ABSTRACT FROM AUTHOR]

This paper reports an elegant approach to address two major challenges of transformerless grid-connected microinverters, common-mode earth leakage current and double-frequency power pulsation across the photovoltaic (PV) terminal. The proposed solution uses an embedded decoupling capacitor in a doubly grounded boost–buck ( $\acute{\mathrm{C}}$ uk) derived topology. An intelligent switching scheme ensures that a large swing of the decoupling capacitor voltage is easily accommodated. Thus, film capacitors can be used instead of electrolytic capacitors, which helps increase equipment lifetime. Details of circuit operation are provided along with dynamic modeling and controller design for close-loop operation. Simulation and experimental results are presented for performance validation of the microinverter. [ABSTRACT FROM AUTHOR]

In this paper, a novel nonisolated bidirectional soft-switching dc–dc converter based on series power units (PU-BDC) with unipolar and bipolar structure for dc networks interconnection is proposed. All semiconductor devices in the PU-BDC operate under soft-switching conditions in both directions with low voltage stress. By operating in the discontinuous conduction mode, all switches and diodes are turned on naturally under zero current. By introducing an auxiliary zero-current-transition commutation cell in each power unit, zero current turn-off of all switches and diodes is achieved to reduce the turn-off loss. Besides, the PU-BDC has a transformerless structure with small volume and low cost, which makes it more suitable for small-scale or medium-scale dc networks and distributed generation systems. In addition, two types of bipolar PU-BDC are proposed to extend its application to bipolar dc networks interconnection. The control system was also optimized for grid-connection applications by providing an output voltage control strategy, a voltage gain control strategy, and a power control strategy to maintain the voltage level or keep a constant voltage gain of the networks and performing precise power control. Finally, simulations of a unipolar PU-BDC and a bipolar PU-BDC with three power units were implemented, and a 1.6-kW experimental prototype of the unipolar PU-BDC with three power units was developed to verify the effectiveness of the converter. [ABSTRACT FROM PUBLISHER]

In this paper, a modified single-phase current source inverter (CSI) with improved multiloop control is proposed for a transformerless grid–photovoltaic interface application. A split capacitor arrangement with the middle point connected to the grid neutral and a common mode choke are used to modify the conventional CSI structure to attenuate the ground leakage current. The proposed control method permits the use of reduced value of dc side inductor by maintaining the quality of the grid current as if a high value of input inductor is used. Furthermore, virtual resistance damping is incorporated in the control loop to reduce the effect of LC resonance without compromising the efficiency, thus proving the feasibility of using CSI for the grid interface. Rigorous study, analysis, and validation of the modified CSI structure with the proposed control technique are carried out with exhaustive simulations and experiments. The experimental results on a 250 W laboratory prototype using the controller TMS320F28335 prove the effectiveness of the proposed CSI structure and its control. [ABSTRACT FROM PUBLISHER]

This paper proposes a new high-gain soft-switching dc–dc topology based on a switched inductor boost converter (SIBC). A conventional SIBC as a high gain boost topology has the issues of high conduction loss in switching diodes and high switching loss in the main switches. Also, it has severe electromagnetic interference (EMI) issue due to high-frequency ringing formed by parasitic inductance and diode junction capacitors. The new topology is derived with the objective of achieving zero voltage switching (ZVS) turn on of the main switch. Instead of adding extra active clamp zero voltage transition (ZVT) path at the switching node, the proposed topology augments the auxiliary ZVT path to the switching diode path. This is achieved by replacing the switching diodes with synchronous switches. The new topology can achieve soft switching for all the switches and alleviate the EMI issue. All the diodes achieve zero current switching (ZCS) turn off without reverse recovery. Auxiliary switches have ZCS turn on and ZVS turn off, and the main switches have ZVS turn on. The soft-switching SIBC also reduces the conduction loss in the switching diodes. A numerical simulation in PLECS and a prototype hardware are built corresponding to a micro-inverter application with 100 kHz switching frequency. Peak power conversion efficiency of 94.76% is achieved in the hardware prototype with Si devices. [ABSTRACT FROM PUBLISHER]

This paper proposes an interleaved hybrid converter (IHC) with simultaneous dc and ac outputs for dc microgrid applications. The IHC is realized by interleaving two conventional boost converters and replacing the active switch of lower boost converter by an H-bridge voltage source inverter. This arrangement enables the proposed IHC to operate at the condition where the sum of duty ratio (\boldsymbolD ) and modulation index (\boldsymbolM ) can be more than or equal to one, i.e., \boldsymbolD + \boldsymbolM \geq 1, unlike the conventional hybrid converters. The proposed IHC is capable of giving dc with high voltage gain and improved ac with reduced harmonic distortion. Due to interleaving nature of the IHC, input current is shared between the power converters and thus enables the use of low current rated switching devices and lower values of inductors. This results in reduced power losses and increased efficiency as compared to the conventional hybrid converters. The IHC also has inherent shoot-through protection capability, better electromagnetic interference immunity, and reliability. A modified unipolar sinusoidal pulse width modulation technique is used to control the power flow of the IHC. Detailed mathematical modeling of the proposed IHC is carried out and its steady-state behavior is validated through experimental results on a 500 W laboratory prototype. [ABSTRACT FROM PUBLISHER]

In this paper, a hybrid bidirectional dc–dc converter is presented, which is a combination of a switched-capacitor converter and an inductor-based converter with low component counts. The input current ripple and peak charging current are small with the help of the inductor. The proposed converter is applicable in the battery charge/discharge systems, such as the distributed renewable energy systems, battery equalizer, auxiliary power supplies, traction drive system, and dual-voltage automotive systems based in new electrical architecture concept, where common ground is not required and within the voltage-gain range of 2–6. A comprehensive analysis of the steady-state operation, small-signal model, and component stress is given. The comparison with an alternative topology shows the advantages of low component counts, low total capacitor voltage stress, low inductor current, and low total active switch stress for the 42/14 V voltage level. A 42/14 V prototype rated at 20–120 W with a peak efficiency of 97.8% in boost mode and 97.62% in buck mode was built to verify the analysis. [ABSTRACT FROM AUTHOR]

This paper presents a single-stage light-emitting diode (LED) driver based on a bridgeless power factor correction (PFC) converter and a half-bridge CLCL resonant converter for street lighting applications. The proposed single-stage topology integrates the PFC converter and the CLCL resonant converter by sharing active power switches. The bridgeless PFC converter adopts two buck–boost circuits operating in discontinuous-conduction mode to achieve input-current shaping. It uses two diodes instead of a rectifier bridge to reduce the power loss caused by the diodes. Owing to its superior soft-switching characteristics, the CLCL resonant converter is used. The proposed LED driver has superior features, such as high efficiency, near unity power factor, low total harmonic distortion, and relatively few diodes. A 100-W lab prototype is successfully implemented, and the experimental results verify the effectiveness and feasibility of the proposed LED driver. [ABSTRACT FROM AUTHOR]

This paper presents a variable switching point predictive current control (VSP $^2$CC) for the quasi-Z-source inverter (qZSI). The proposed VSP $^2$CC aims to remove the output current error on the ac side, as well as the inductor current and capacitor voltage errors of the quasi-Z-source network on the dc side of the converter. Unlike the previously presented direct model predictive control (MPC) strategies for the qZSI, the proposed control scheme can directly apply the switching signals not only at the discrete time instants, but at any time instant within the sampling interval. Consequently, the shoot-through state can be applied for a shorter time than the sampling interval, resulting in lower output and inductor currents ripples. Experimental results based on field programmable gate array are provided to verify the effectiveness of the introduced control method. As it is shown, the proposed method leads to lower inductor current ripples and less output current total harmonic distortion when compared with the conventional direct MPC. [ABSTRACT FROM AUTHOR]

A trend for low-power conversion system is to integrate every component to a single chip. Magnetic component has been the key to determine the power density of the integrated switching power converter. In this paper, a hybrid resonant buck-type converter with an ultracompact custom-designed coupled inductor is presented for low-power integrated on-chip applications. This converter achieves zero-voltage switching for the high-side switch and near zero-voltage zero-current switching for low-side and auxiliary switches. The soft-switching condition allows the circuit operating at high switching frequencies. An ultracompact planar coupled inductor with a dimension of 5.25 mm × 1.95 mm × 3.86 mm is designed and customized for future integrated on-chip applications. The high-power density of this magnetics component is achieved by high switching frequency and optimized printed circuit board (PCB) windings design. A hardware prototype with 24 to 60-V input and 3.3 to 5-V, 3-A output operating at 2–3 MHz is presented to verify the circuit operation. The prototype achieves a peak efficiency of 90.7% using silicon devices at 2-MHz switching frequency. [ABSTRACT FROM PUBLISHER]