Search

Multilevel inverters (MLIs) are playing a pivotal role in the power sector with potential applications, such as interfacing renewable energy sources with the grid and several industrial drive applications. MLIs with a smaller number of switching devices are more promising due to their compact size, reduced cost, and higher efficiency compared with their traditional counterparts. This paper, therefore, presents a new three-phase seven-level inverter. This topology is a combination of two cascade-connected two-level voltage-source inverters (VSIs) and H-bridge cells with flying capacitors (FCs). This paper presents the operating principle and the balancing technique for the dc-link capacitors and FCs. The generation of various output voltage levels and the limitation of the sinusoidal pulsewidth modulation control for FC voltage balancing is also presented. The number of components in the proposed circuit configuration and their voltage ratings are considerably lower compared with the recently proposed topologies. The behavior of the proposed circuit configuration is first assessed with simulation studies and is then tested with a laboratory prototype. The simulation and experimental results validate the effectiveness of the proposed topology and the voltage balancing technique. [ABSTRACT FROM AUTHOR]

An improved bridgeless (BL) Cuk converter-based electric vehicle (EV) battery charger with high power factor and increased efficiency is designed and developed in this paper. It provides low cost and high-power-density-based charging solution for the EV. This charger incorporates less number of devices operating over one switching cycle, which reduces the additional conduction loss incurred by a diode bridge rectifier of the conventional charger. Hence, it improves the charger's efficiency. The added advantage of the proposed topology is that the unwanted capacitive coupling loop is removed, as well as the unwanted conduction through the body diode of the inactive switch in the previously developed BL Cuk converter is avoided. This significantly improves the charger's efficiency. For the constant current and constant voltage charging, the commands are synchronized by a flyback converter. The proposed charger draws a sinusoidal current from ac mains and the total harmonic distortion in the supply current is reduced to the limits specified by the IEC 61000-3-2 guidelines. The improved efficiency and power quality indices of the proposed charger are investigated to demonstrate its satisfactory charging operation at all operating conditions. [ABSTRACT FROM AUTHOR]

This paper proposes a novel open-winding brushless doubly-fed reluctance generator (OW-BDFRG) with dual two-level converters in order to reduce the converter rating and switching frequency for large-scale wind turbine applications. The new converter topology is equivalent to a three-level converter directly connected to the control winding of typical BDFRG. The OW-BDFRG system with this topology structure requires lower converter rating and switching frequency, and has a more flexible control mode, better operation performance, and fault redundancy capability. For the OW-BDFRG, this paper also proposes a new control scheme combining direct power control (DPC) with sliding mode variable structure (SMVS) control to implement the power tracking. The voltage-vector switching table of DPC is redesigned according to the error signals of active and reactive powers of the power winding, as well as the sector location of control winding flux. The active and reactive powers of the OW-BDFRG can be directly decoupled and independently controlled by properly selecting the switching voltage vectors. The novelty of this paper lies in an OW-BDFRG topology driven by dual two-level converters to improve the system characteristics, and the use of SMVS control to improve the DPC accuracy and robustness to parameter variations. Finally, the effectiveness of the proposed system is verified through simulation and experimental studies. [ABSTRACT FROM AUTHOR]

The hybrid modular multilevel converter with cascaded full bridges (HMMC-CFB) is a recently proposed dc fault tolerant converter topology for high-power applications. It has a director part (DP) consisting of a series of connected half-bridge submodules, and a wave-shaping part (WSP) composed of a series of connected full-bridge submodules (FBSMs). The submodules in DP avoid high voltage stresses and improve synchronization between DP and WSP by slowing down the change rate of DP output voltage. This slowdown is achieved by using a trapezoidal reference signal for DP. The WSP attenuates the voltage harmonics produced by DP. However, the energy exchanged by WSP changes with modulation index, which may cause improper voltage regulation of the submodule capacitors. This paper proposes a new control technique to regulate the energy exchanged by WSP, which uses a variable slope trapezoidal reference signal of DP. To obtain this slope, the feedforward and feedback controllers are used. The feedforward controller gives the value of slope depending on the modulation index (mv) to keep the energy exchanged by WSP nearly equal to zero, whereas the losses and nonideality of the converter are taken care of by the feedback controller. This technique guarantees proper voltage regulation of the submodule capacitors for all modulation indices. The efficacy of the proposed technique is confirmed using simulations and experimentations. This paper also presents a circulating current suppressing controller for HMMC-CFB. The proposed control schemes and dc fault tolerant capability of HMMC-CFB are tested on a grid-connected model built in PSCAD. [ABSTRACT FROM AUTHOR]

This paper presents an isolated auxiliary power supply for medium-voltage power electronics systems. The proposed converter comprises two stages: a non-isolated ac/dc stage that connects directly to the medium-voltage line, and an isolated dc/dc stage that provides 100-W output power at 24 V, with 10 kV isolation. The proposed modular ac/dc stage uses just one active semiconductor device per module, features an internal capacitor voltage balancing, and achieves power factor correction by employing predictive current control. High switching frequency operation of both converter stages enable a reduction in system size and weight when compared to traditional low-frequency transformer-based approach. The proposed converter is simulated and its operation is validated experimentally on a 100-W prototype. [ABSTRACT FROM AUTHOR]

In this paper, a highly reliable back-to-back (BTB) power converter is proposed for doubly fed induction generator-based wind turbines (DFIG-WTs). When a power switch open-circuit fault is encountered in either the grid-side converter (GSC) or the rotor-side converter (RSC), a four-switch three-phase (FSTP) topology is formed to avoid using redundant bridge arms, which reduces the power circuit complexity and minimizes the conduction and switching losses. A simplified space vector pulsewidth modulation technique is used to eliminate sector identification and complex trigonometric calculations. In addition, the influence of dc-bus capacitor voltage unbalance on the electromagnetic torque is analyzed in detail. The offset current components are calculated, and they are deducted from the reference values in the modified control strategies to suppress the dc-bus voltage deviation. Moreover, the power loss model of a BTB converter is analyzed in detail, and the efficiency study is performed in various post-fault situations. Simulations in MATLAB/Simulink are carried out to verify the performance of a DFIG-WT based on a FSTP BTB converter. Furthermore, the control hardware-in-the-loop setup with RSC and GSC separately simulated in a digital real-time simulator is applied for experimental verification of the proposed control strategy. [ABSTRACT FROM AUTHOR]

Low-voltage dc distribution systems have gained significant attention over the last years, since they provide simpler and more efficient integration of distributed generators and storage devices, establishing a pathway to net zero energy buildings. In low-power units, transformerless utility interface is preferred to reduce footprint and losses. However, the lack of galvanic isolation introduces a common-mode (CM) path between the dc distribution bus and the utility service grounding, leading to the presence of high CM voltages at the dc bus feeders. The attenuation of the CM voltage reduces the touch voltage amplitude and leakage current, contributing to a safer environment. In this paper, a feed-forward active compensation of the CM voltage is proposed. It relies on utility voltage parameters, estimated by a phase locked loop, to generate a counter CM voltage; hence, it does not require previous knowledge of the system CM path model or the addition of voltage sensors. Experimental results show that this technique can attenuate the CM voltage to non-dangerous magnitudes without interfering with the microgrid differential mode behavior. [ABSTRACT FROM AUTHOR]

Many of the renewable energy resources, like offshore wind, utility PV farms, are located far away from the load centers, which requires dc power transmission system to efficiently deliver power. Voltage-source converter solution is required in many applications due to the stability and compensation requirement. This paper presents a new voltage source converter topology for medium to high voltage dc application, named modular embedded multilevel converter (MEMC). MEMC is based on a three-level topology structure and consists of series-connected insulated-gate bipolar transistor (IGBT) bridge stacks, like the popular modular multilevel converter (MMC) and series-connected thyristor or press-pack high voltage integrated gate-commutated thyristor or IGBT stacks. The basic operation principle, control solutions, and the methods to commutate the thyristors are explained in detail. Due to the three-level structure, the total number of IGBT stacks are reduced by half compared with MMC, leading to much lower energy storage, weight, volume, and system complexity. Also by replacing part of the IGBT stack in MMC with thyristor stack, both of the system conduction loss and switching loss can be further reduced. There are other topology variations of MEMC with a similar operational principle but different characteristics. [ABSTRACT FROM AUTHOR]

An adaptive control of DPWM implementable in clamped-three-level inverters with two strings of photovoltaic (PV) panels in cascaded connection is proposed in this paper. The proposed modulation is developed based on the so-called circuit-level decoupling concept. It is able to provide balance line voltage even under unbalanced dc links. The unequal dc voltages appeared due to asymmetric maximum point of power trackings (MPPTs) are controlled by proper injection of zero-sequence voltage to the common mode voltage, while the total dc voltage is regulated based on the voltage commands generated by the MPPT of each string. Thus, both PV strings are able to be operated based on their MPPTs while there is almost no low-order harmonic distortion at the inverter output current. Compared with the previous methods, the high capability of the proposed method is evaluated by simulation study and experimental tests. [ABSTRACT FROM AUTHOR]

This paper investigates ac–dc–ac multilevel topologies for three-phase four-wire applications obtained from an interconnection of three-leg voltage-source converters. The topologies can be applied in line voltage regulators, universal active power filters, and uninterrupted power supplies. Operating principles, a pulsewidth modulation (PWM) technique, and an overall control strategy are developed. The PWM and control strategies are suitable to regulate the dc-link voltages and to reduce the harmonic distortion, switching stress, and power losses. Simulation results are used to compare the proposed configurations with a conventional solution in terms of harmonic distortion, semiconductor losses, and others characteristics. Experimental results are presented to validate the theoretical considerations and were obtained by using insulated-gate bipolar transistors with dedicated drives and a digital signal processor with appropriated plug-in boards and sensors. [ABSTRACT FROM AUTHOR]

In this paper, a fifth-order boost point-of-load converter is developed by cascading a modified fourth-order boost converter with a combination of L–C and diode. This topology has the following salient features: Single-switch topology, common ground between source and load, low-voltage stress across intermediate capacitors, and voltage gain same as other reported fifth-order boost converters with no common ground. Steady-state and dynamic analyses demonstrate the proposed converter's boosting feature and dynamic performance, respectively. A contoured robust Bode plot methodology is employed to design the robust voltage-mode controller to ensure load voltage regulation in the presence of uncertainties. The necessary and sufficient conditions under which the designed controller guarantees the load voltage regulation and robust stability are obtained. A step-by-step robust controller design procedure is outlined. The salient features of the proposed converter and its robust performance are studied analytically, using the MATLAB platform, and validated experimentally on a 60-W prototype module. [ABSTRACT FROM AUTHOR]

This paper investigates an ac–dc–ac multilevel power converter. The studied configuration is composed of two single-phase ac–dc–ac three-leg modules and series-connected H-bridges in the shared part of system. Because the proposed converter has shared legs between the input and output, it is employed in applications with same input and output frequency. Uninterrupted power supply and unified power quality conditioner are application examples for this converter. Such multilevel topology has lower dc-link voltage rating, which, consequently, presents low switch blocking voltages when compared to conventional topologies. System model, a space-vector pulsewidth modulation (PWM) strategy to symmetrical and asymmetrical dc-link voltages, and an overall control strategy to adjust the system variables are presented. A power flux analysis shows the operation zone in which the individual dc-link voltage balancing is possible. PWM and control strategies are developed to reduce the semiconductor total losses, harmonic distortion, and switching stress. Two ac–dc–ac multilevel conventional structures are used for comparison. Simulation and experimental results demonstrate the feasibility of the studied converter. [ABSTRACT FROM AUTHOR]

This paper investigates a multilevel inverter composed of series/parallel-connected H-bridges. The presented structure can be used for applications in which the use of semiconductor switches with low-voltage and low-current ratings is intended. A comprehensive system model, an overall control strategy to adjust the output voltage with constant magnitude and frequency, and a level-shifted PWM (LS-PWM) strategy based on a voltage vectors unidimensional analysis and a plane analysis are presented. The LS-PWM is capable of mitigating the low-frequency circulating current, thus generating multilevel voltage signals with low harmonic distortion, maximum number of levels, and low dv/dt. In addition, considering a wide range of values of voltages and currents and various power levels, the total converter losses are reduced compared with the conventional multilevel converters. Two multilevel conventional inverters with the same number of semiconductor switches are used for comparison. Simulation and experimental results demonstrate the feasibility of the studied converter. [ABSTRACT FROM AUTHOR]

This paper presents an improved dc-link voltage balancing algorithm for a three-level neutral-point-clamped inverter by considering phase current direction. Detailed studies on the effects of change in load current direction on the dc-link capacitor voltages are presented. A maximum value of power factor is numerically derived, above which it affects the capacitor voltage balancing capability. Compared with the previously presented research work, the inputs to the space-vector pulsewidth-modulation block are the three phase currents and the difference between the two capacitor voltages. Depending on the states of the two dc-link capacitor voltages and phase current direction, redundant voltage vector sequences are selected. The selected vectors keep the capacitor voltage deviations within 5% of the total dc-link voltage. Two zero switching vectors (i.e., PPP and NNN) are also removed from all subsectors of the earlier proposed strategy, which one used to produce higher common-mode voltages. Detailed simulation and experimental results are presented in this paper for a 6.0-kW surface permanent-magnet synchronous machine. Both the simulation and experimental results show the required performance of the proposed system. [ABSTRACT FROM AUTHOR]

Multilevel converters are a proven solution for medium-voltage and high-power applications, including renewable energy conversion. Developing 6.6-kV converters is a key goal for the wind turbines industry. Considering the voltage rating of commercially available semiconductors, five-level converters are necessary to reach 6.6 kV. The five-level active neutral-point-clamped converter (5L-ANPC) is one of the most advantageous topologies among five-level multilevel converters. This paper presents a new 5L-ANPC topology that overcomes the features of the previously employed 5L-ANPC topology. Along this paper, the properties and working principle of this new 5L-ANPC are explained. Finally, the validity of the new converter is validated via simulation and experimental results. [ABSTRACT FROM AUTHOR]

This paper discusses the use of a cascaded multilevel converter for flexible power conditioning in smart-grid applications. The main feature of the proposed scheme is the use of independent dc links with reduced voltages, which makes such a topology an ideal candidate for medium- and high-power applications with increased reliability. The developed control strategy regulates independent dc-link voltages in each H-bridge cell, and allows the selective and flexible compensation of disturbing currents under a variety of voltage conditions without requiring any reference frame transformation. The selective control strategies are based on the decompositions proposed in the conservative power theory, which result in several current-related terms associated with specific load characteristics. These current components are independent of each other and may be used to define different compensation strategies, which can be selective in minimizing particular effects of disturbing loads. Experimental results are provided to validate the possibilities and performance of the proposed control strategies, considering ideal and deteriorated voltage conditions. [ABSTRACT FROM PUBLISHER]

This paper presents a dc/dc buck–boost converter topology with high-voltage gain and dual outputs. Unlike many of the high step-down/step-up dc/dc converters, this topology uses a relatively ower number of LC components and three active semiconductor devices switched in a nonoverlapping way. Due to the duty cycle limitation, high gain (typically more than 4) is very difficult to achieve in a single-stage regular buck–boost dc/dc converter. In the proposed converter, the overall gains at both the output ports are nonlinear functions of duty-cycles of the power devices, which help achieve an overall step-down/step-up gain of 10–15. An experimental prototype converting 48 V dc to ±5 V dc at 100 W with closed loop control is developed in order to verify the operation and effectiveness of the proposed converter structure. An output voltage ripple of ±1% and a conversion efficiency of 94% are achieved according to the experimental results. [ABSTRACT FROM PUBLISHER]

This paper proposes a new nine-level inverter for medium- and high-power applications. The proposed topology comprises of a three-level (3L) active neutral-point-clamped (ANPC) inverter connected in series with a floating capacitor (FC) fed H-bridge. Besides, two additional switches operating at line frequency are appended across the dc link of the 3L ANPC structure. Compared with conventional hybrid cascaded inverters, the primary advantage of this addition is doubling of the resulting root mean square output voltage. This amelioration is achieved while preserving the standard 3L ANPC and H-bridge structures with minimum topological modification. A simple logic-gate-based voltage balancing scheme is developed to regulate the FC voltage. The proposed voltage balancing method is independent of load power factor, inverter modulation index, and can balance the voltage across FC instantaneously. The step-by-step formulation of logical expressions for the generation of gating pulses is deliberated in detail and can be generalized for any $n$-level inverter. Further, simulation results as well as the experimental measurements obtained from the laboratory prototype are presented to validate the effectiveness and practicability of the proposed configuration. Finally, the notable merits of the proposed inverter over the prior art topologies is established through a comprehensive comparative study. [ABSTRACT FROM PUBLISHER]

This paper presents a single-stage solar photovoltaic (SPV) system utilizing an adaptive control scheme. The SPV system includes SPV array, voltage source converter (VSC), ripple filter, nonlinear loads, and a distribution network. The proposed SPV system feeds the active power to the distribution system, provides an effective use of SPV array and mitigation of load harmonics currents. The SPV system with an incremental conductance based control scheme is used for obtaining the maximum power from the SPV array and an adaptive control scheme to control the switching pulses of the VSC. In addition, it utilizes a SPV feed-forward loop to improve the dynamic response and reduces the burden on the proportional-integral controller by regulating dc bus voltage. Test results are presented to validate the control, design, and response of SPV system with various states. [ABSTRACT FROM PUBLISHER]

This paper investigates the utilization of two different six-leg configurations of single-phase to three-phase converters. One of the topologies is transformerless and the other is transformer based. The studied converters allow feeding the load voltage with sinusoidal voltages with constant amplitude and frequency, and to operate with sinusoidal grid current with high power factor. The system model and pulse-width modulation techniques for one of the topologies are given. Control strategies for both topologies are provided. The studied topologies are compared with the conventional in terms of dc-link specification, voltages harmonic distortions, semiconductor losses, and other characteristics. Simulation and experimental results are provided to illustrate the operation of the systems. [ABSTRACT FROM PUBLISHER]

A novel hybrid five-level voltage-source converter for high-efficiency applications is investigated in this paper. Compared with traditional multilevel converters, this hybrid multilevel converter generates desired staircase voltage levels with a reduced number of power devices and isolated drivers at higher voltage levels. It has redundant switching state combinations in hybrid multilevel converter, which makes it easy to balance flying capacitor voltages and realize fault-tolerant operation. A voltage-balancing control strategy based on switching state redundancies is presented for the hybrid multilevel converter to generate desired levels and also keep voltage balance of flying capacitors at the same time. The performance of the hybrid multilevel converter under various operating conditions is investigated in MATLAB/Simulink. The effectiveness of the proposed hybrid multilevel converter is validated by experiment results. [ABSTRACT FROM AUTHOR]

This paper proposes and investigates a new three-phase ac–dc–ac multilevel conversion system obtained from cascaded three-leg converters. Such configuration presents advantages in terms of reduced switch blocking voltages and consequently lower dc-link voltage rating. Operating principles, a pulse-width modulation (PWM) technique based on vector approach, and a control strategy are presented. The operation with different dc-link voltage values and a balancing method are discussed, and is supported by simulation and experimental results. The PWM technique is able to generate multilevel voltage waveforms, which permits reducing the switching frequency stress leading to reduced semiconductor losses. Simulation results are used to compare the proposed configuration with a conventional solution in terms of harmonic distortion and semiconductor losses. Experimental results demonstrate the feasibility of the studied converter, and were obtained by using a downscaled prototype with insulated gate bipolar transistors with dedicated drives and a digital signal processor with appropriated plug-in boards and sensors. [ABSTRACT FROM PUBLISHER]

This paper proposes three dynamic voltage restorer (DVR) topologies. Such configurations are able to compensate voltage sags/swells in three-phase four-wire (3P4W) systems under balanced and unbalanced conditions. The proposed systems use two independent dc links. Proposed configurations present advantages in terms of switch blocking voltages and consequently lower dc-link voltage rating. The complete control system, including the pulsewidth modulation (PWM) technique, is developed, and comparisons between the proposed configurations and a conventional one are performed. Simulation and experimental results are provided to validate the theoretical approach. [ABSTRACT FROM AUTHOR]

This paper presents a carrier-based pulsewidth modulation (PWM) method that reduces the common-mode voltage (CMV) of a three-level four-leg converter. Based on an analysis of space vector PWM (SVPWM) and sinusoidal-PWM switching patterns, the fourth-leg pole voltage of a three-phase converter, known as the “f pole voltage,” is manipulated to reduce the CMV. To synthesize the f pole voltage for the suppression of the CMV, positive and negative pole voltage references of the f leg are calculated. In addition, the offset voltage to prevent distortion of the a, b, and c phase voltages regarding the neutral point is deduced. The proposed PWM strategy can be easily implemented in the software of a DSP-based converter control. The three-level four-leg converter with the proposed PWM algorithm results in a remarkable reduction in the peak-to-peak value of the CMV. From the simulation and the experimental results, the peak-to-peak value of the CMV when using the proposed PWM method is 33% compared to that when using the SVPWM method, while the number of CMV transitions during the switching period in the proposed PWM method is only 25% of that when using the SVPWM method. [ABSTRACT FROM PUBLISHER]

This paper presents a new nonisolated buck/boost-type multilevel dc–dc converter suitable for high-power and medium/high-voltage application. The main features of the proposed topology are as follows: low voltage across the semiconductors, low switching losses, and reduced volume of the output filter. The theoretical analysis is carried out for a five-level bidirectional structure of the proposed converter, operating in Buck mode. The proposed topology presents some capacitors, and their voltage must be balanced for proper operation of the converter. Thus, a capacitor voltage balancing active control using a feedforward technique is proposed and analyzed in detail. In order to validate the theoretical analysis, a prototype with 10 kW output power capability, 1.3 kV to 800 V input-to-output voltage, and 20 kHz of switching frequency was built and experimented. The results attest the advantages of the new dc–dc topology, as well as the new capacitor voltage control technique. [ABSTRACT FROM AUTHOR]

This paper introduces a novel isolated hybrid resonant converter with smooth transition between multiple operating modes. With the simple addition of a bidirectional ac switch, the highly efficient series resonant converter operating in the discontinuous conduction mode is combined with a phase-shifted full-bridge buck converter and a pulsewidth-modulated boost converter in order to provide high power conversion efficiency over a wide input-voltage operating range utilizing a simple topology and simple control techniques. First, the topology is introduced, and the converter's operating modes are discussed. Next, closed-loop input-voltage controllers are designed for the different operating modes, and a smooth transition technique is introduced using a two-carrier modulation scheme. Experimental results are provided to verify the proposed system using a 300-W prototype that achieved a 97.5% California Energy Commission weighted efficiency with a 30-V input including all auxiliary and control losses. [ABSTRACT FROM AUTHOR]