Search

This paper discusses a novel methodology to increase the voltage droop compensation range in generalized solid-state bipolar high-voltage Marx modulators with one resonant stage. To maintain the modularity characteristic of bipolar Marx modulators, the imbedding of additional resonant stages is not straightforward. Nevertheless, this paper proposes to add a second resonant stage to the already existing resonant-type voltage droop compensation stage. This second stage increases the voltage droop compensation percentage of a generalized solid-state bipolar Marx generator. The compensation of the bipolar pulse voltage droop is now achieved by adding two auxiliary synchronous compensation resonant voltages, to the output capacitive decaying voltage. Simulation and experimental results are presented for six Marx plus two resonant stages, 16% voltage droop, with 3-kV pulse amplitude, 100- $\mu \text{s}$ pulsewidth, 40-ms relaxation time, and 10-Hz pulse repetition rate. [ABSTRACT FROM AUTHOR]

This paper presents the effect of stray capacitances in bipolar (negative and/or positive) pulses generated by the two different topologies of the solid-state Marx modulators. According to the analysis, the stray capacitances influence the energy transfer from the Marx modulator capacitors to the load affecting the bipolar (negative and/or positive) pulse rise time. This paper deals with the structure design to reduce the influence of the stray capacitance and to improve the pulse rise time of these bipolar solid-state Marx modulators. A four-stage laboratory prototype of the two topologies has been assembled using 1200-V insulated gate bipolar transistors and diodes, operating with 1000-V dc input voltage and 1-kHz frequency, producing 4-kV bipolar pulses, with 5- \mu \texts pulse duration and 120-ns rise time, into a resistive load. [ABSTRACT FROM PUBLISHER]

Superconducting pulsed-power supply (SPPS) provides an efficient method for both high-density inductive energy storage and high current pulse generation. An SPPS consisting of eight high-temperature superconducting pulsed-power transformer (HTSPPT) modules with XRAM methodology was designed and simulated in preliminary studies. It recycled the leakage flux energy and reduced the voltage across the opening switch with a capacitor in primary. However, the SPPS with XRAM methodology has two problems. The first one is that it can provide high pulse amplitude, but cannot provide enough width. The other one is that the ratio of the maximum capacitive energy over the total inductive energy is relatively large, which cuts down the overall system energy density. This paper proposes a modified topology of SPPS with capacitor reuse methodology. Multiple HTSPPT modules are divided into several groups. Each group shares the same capacitor. The procedure of the modified SPPS is presented in detail. A 270-kJ SPPS with capacitor reuse methodology is designed and simulated to illustrate the modified topology. With the load parameters of a small railgun, the peak value of the load current is 207.15 kA and the pulse half-height width is 5.56 ms, the ratio of the maximum capacitive energy over the total inductive energy is 11%. The characteristics of the modified topology are also described in detail in this paper. [ABSTRACT FROM PUBLISHER]

This paper shows how to use modular Marx multilevel converter diode ( \textM^3 CD) modules to apply unipolar or bipolar high-voltage pulses for pulsed power applications. The \textM^3 CD cells allow the assembly of a multilevel converter without needing complex algorithms and parameter measurement to balance the capacitor voltages. This paper also explains how to supply all the modular cells in order to ensure galvanic isolation between control circuits and power circuits. The experimental results for a generator with seven levels, and unipolar and bipolar pulses into resistive, inductive, and capacitive loads are presented. [ABSTRACT FROM AUTHOR]

This paper proposed the use of a ringer, a self-switched inductive storage system, for applications involving reluctance accelerators, a kind of electromagnetic launcher, and compatible with applications where portability is a requirement. There will be shown three different useful approximations for the analysis of the ringer, employed as a power source for a reluctance accelerator. First, it described the equations governing the que behavior of an ideal unloaded ringer, and then the equations for the ringer with an uncoupled inductive load, and ultimately a Lagrangian model for the ringer as an inductive power source for a reluctance accelerator, capable to make predictions about the currents through the circuits and the exit speed of the projectile for a given firing. The accuracy of the predictions made with the third approximation, the Lagrangian model, was tested experimentally. [ABSTRACT FROM AUTHOR]

Recently, inductive energy storage systems have attracted interests due to high energy densities. The high-temperature superconducting pulsed-power supply (HTSPPS) is one inductive PS topology for electromagnetic launching system. The topology can achieve a high amplitude load current and cut down the electrical losses due to the zero resistance characteristic of superconducting inductors. However, in this topology, the integrated gated commuted thyristor is used as a switch and cannot withstand high current, which limits the expansion of the system. Besides, it has significant current amplification ability as a single unit, but one module cannot provide sufficient amplitude and appropriate pulsewidth for the load current of the electromagnetic launching. In this paper, by applying the principle of inverse current commutation with semiconductor devices (ICCOS) in the HTSPPS, a novel circuit topology called HTSPPS with ICCOS is presented. This topology is analyzed and the multiple modules system is established. Simulation results show that the HTSPPS with ICCOS exceeds the current limitations of the original one and ensures the reliable cutting off of the main switch. It has potential applications in the future of high-energy systems while reducing the cost greatly. By asynchronous cooperative triggered discharge of the multiple HTSPPS with ICCOS modules in parallel, the appropriate amplitude and flat shape current of the load can be achieved through the careful design of the trigger time. [ABSTRACT FROM AUTHOR]

This paper presents a new capacitor bank topology for a pulsed power system to improve the efficiency of multistage synchronous induction coilgun. In the proposed method, a switch, such a gate turn-off thyristor, is inserted in parallel to a crowbar diode and load to generate an attractive force between the next stator and the armature. A mathematical model was developed, and finite-element method simulations were conducted to verify the proposed topology. The results show that the proposed method improves the energy efficiency and launch velocity. The improvement in energy efficiency is confirmed from the simulation results of a three-stage synchronous induction coilgun. [ABSTRACT FROM AUTHOR]

Slow transfer of energy through capacitive hybrid (STRETCH) meat grinder circuit, which was proposed by the Institute for Advanced Technology, added a capacitor into the traditional meat grinder circuit. Even though its energy density is slightly less than the corresponding pure inductance system, it can reduce the voltage across the opening switch and maintain the high multiplication factor of the opening current. The performance of the STRETCH meat grinder circuit depends on multiple parameters. The inductance ratio ( n=L1 / L2) and the capacitance (C) are the two vital factors, which have a crucial influence on the system performance, such as the voltage over the opening switch ( V_{\rm Sopm}) , the current multiplication factor ( m$ ), and the ratio of the maximum capacitive energy over the total inductive energy ( $\eta )$ . Thorough studies have been carried out in this paper on the relationship between the above two factors and the three performance criteria. This paper also discusses and analyzes the chosen of the key parameters ( $n$ and $C$ ) for a single-stage STRETCH meat grinder with 2-mH total inductance, which is made up of two serial coils with 0.95 coupling factor. The opening current of the main switch is 1 kA, which constitutes a 1-kJ inductive pulsed-power supply. It fully takes the advantage of the STRETCH meat grinder topology, intensifies the study of the inductive pulsed-power supply with higher energies, and is easy to be utilized for practical application. [ABSTRACT FROM PUBLISHER]

The STRETCH meat grinder is one typical inductive pulsed-power supply topology for electromagnetic launch system. It has remarkable current amplification ability as a single unit, but one module cannot provide enough amplitude and width for the load current of the railgun launching. This paper discusses the effects of different triggering delays on the load current with two STRETCH meat grinder modules. To reduce the magnetic field coupling between the two modules, the two main switches are opened simultaneously. To make the load current waveform with no notch, the thyristor of the first module is triggered when its pulse-forming capacitor is fully reversely charged. For the thyristor of the second module, we consider several time points of triggering delay. Because of the practical constraint for the maximum rail current that ensures no rail erosion, the rectangular waveform is the most appropriate load current waveform. Therefore, the comparing criterion can be defined as the ratio of the load current waveform area and its maximum rectangle area at different current levels. Higher ratio means that the current is more like a rectangular wave and is better accordingly. Based on the above criterion and extensive simulation research, we found that the best delay time is the moment when the capacitor is reversely charging the inductor completely. This paper and the result are of great theoretical significance for the further study on the collaborative triggering of multiple STRETCH meat grinder modules. [ABSTRACT FROM PUBLISHER]

In this paper, a compact circuit topology is presented for pulsed power generation with a semiconductor opening switch (SOS). Such circuits require the generation of a fast forward current through the diode, followed by a reverse current that activates the recovery process. In general, magnetic switches are used to switch the diode current from forward to reverse. Therefore, adjustment of the output voltage of an SOS pulser is difficult. This paper introduces a circuit that allows an adjustable output voltage of the pulser. A solution is realized with a premagnetizing circuit on the primary winding of a pulse transformer (PT), so that a third winding is not needed. The primary capacitor voltage can now be varied while maintaining proper saturation of the PT. [ABSTRACT FROM PUBLISHER]

This paper describes a high-frequency pulsed-power generator for various industrial applications such as water treatment, food and medical apparatus for sterilization, or polluted gas treatment. The system is made of silicon-controlled rectifier as a main trigger switch, capacitors, two-stage magnetic pulse compression stages, and a linear transformer to generate a maximum of 120-kV, 5-kA pulse. The parameters obtained through the development are: output voltage: 120 kV (maximum), pulse repetition ration: 300 pulse per second, pulsewidth: 0.25~\mu \texts , and mean power: 30 kW. The designed pulsed-power generator is confirmed to be used effectively for many high-voltage pulsed-power applications related to environmental industry by simulation and experiments. [ABSTRACT FROM AUTHOR]

This paper describes the design, implementation, and comparison of high-voltage capacitor chargers for a solid-state pulsed power modulator (SSPPM). The three different converter topologies are a series resonant converter operating at a discontinuous conduction mode with switching frequency control (SRC_DCM_SFC), a series resonant converter operating at a continuous conduction mode with phase shifted pulse width modulation control (SRC_CCM_PSPWMC), and a series–parallel resonant converter operating at the CCM with SFC (SPRC_CCM_SFC). On the basis of these converter topologies, 10\-kW\rm{average} high-voltage capacitor chargers are designed for the three types of SSPPMs, which have the following maximum output specifications: 1) SRC_DCM_SFC: 60 kV, 300 A, 3 kpps, and 50 \mus; 2) SRC_CCM_PSPWMC: 10 kV, 50 A, 50 kpps, and 10 \mus; and 3) SPRC_CCM_SFC: 40 kV, 150 A, 7 kpps, and 10 \mus. Although the pulse output specifications are different, it is worth comparing the resonant inverter topologies and the control methods from the viewpoint of the losses, control characteristics, and merits and demerits of the high-voltage capacitor chargers. From the analysis and investigation of the three resonant inverters, the design procedure, including the determination of the resonant tank parameters, is provided, which considers the design of the high-voltage capacitor charger. PSPICE simulation is used to elucidate the effects of the resonant tank structure and its parameters, and the resonant current waveform and losses of the Insulated Gate Bipolar Transistor are compared. Finally, experiments for each charger are performed under various load conditions, and the comparison results of the three capacitor chargers, including the conduction and switching losses, control characteristics, and overall efficiency, are discussed in this paper. [ABSTRACT FROM AUTHOR]

A 200 kJ pulsed power system (PPS) has been built up to drive pulsed plasma devices. This PPS consists of two 100 kJ capacitor bank modules, each comprising of five capacitors of each 178~\mu \textF , a discharge switch, and a pulse-shaping unit. When both the banks are charged simultaneously to −15 kV using full charging technique, it delivers a peak current 100 kA at the load (damping resistor and pulse-shaping inductor). Later on, a plasma system will be attached at the load which will also have an inductive and resistive effect. A fiber-optic triggering unit controls both the modules and there exists a flexibility of sometimes operating a single module only, besides there are provisions for further up gradation of the PPS to a targeted 600 kJ. Prior to this development, PSpice simulation was carried out to estimate the parameters of the circuit components to achieve the required wave pulse with precision. Using these parameters, a design of the PPS was made keeping into account about the critical issues involved and the ratings of the components, some of which were fabricated in house. This paper basically includes the criticality surrounding the operation of a high-energy long-pulse PPS under negative operating voltage. [ABSTRACT FROM AUTHOR]

With inherent strengths in energy density and power density, the inductive pulsed power supplies (IPPS) have become an attractive option for the power supplies in electromagnetic launch systems. The meat grinder circuits, including the slow transfer of energy through capacitive hybrid (STRETCH) meat grinder circuit, the STRETCH meat grinder with inverse current commutation with semiconductor devices circuit, and the meat grinder with self-charged capacitor and thyristors circuit, constitute one major branch among the IPPS circuits. This paper summarizes the fundamental research work and contributions of the meat grinder circuits from the perspectives of circuit improvements, performance analysis, inductor design, module collaboration, and efficiency promotion. The future directions of single IPPS module are higher energy level, larger energy density, and higher efficiency. [ABSTRACT FROM PUBLISHER]

This paper presents a novel technique for the voltage droop compensation of long pulses in solid-state bipolar high-voltage Marx generators. Considering the modularity of Marx generators the compensation consists in adding one extra stage to perform as a pulsewidth modulation circuit. This stage voltage is added to the output positive or negative pulses, and an output LfCf filter is included to smooth the voltage pulse waveform. A five-stage laboratory prototype of this circuit has been assembled using 1200-V Insulated Gate Bipolar Transistors and diodes with 1000-V dc input voltage. The circuit was operated at 50-Hz bipolar pulse rate, giving 4-kV bipolar pulses, into a resistive load, with 100- \mu \texts pulsewidth and 9.5-ms relaxation time. The circuit was able to compensate 10% of bipolar pulse voltage droop. [ABSTRACT FROM PUBLISHER]

This paper presents a power electronics converter to generate bipolar high-voltage pulses using low-voltage dc source. Converter is designed based on charging of different capacitors by a predetermined switching pattern and their discharging on the load for pulsed power applications. Low number of power electronics devices and bulky transformer elimination are main advantages of the proposed converter. According to new findings, bipolar high-voltage pulses may lead to higher efficiency in many applications, such as food sterilization industry. The proposed pulse generator generates bipolar controllable pulses with a modular circuit structure based on a capacitor-switched network. Experimental results are presented to verify the analysis. [ABSTRACT FROM AUTHOR]

The series configuration of fast semiconductor switches seems to be the key component in the high-voltage and fast rising time pulse generation. In this approach, two important issues must be considered. The first is to provide a safe operating condition for the switches in transient intervals. The second is to design a gate drive system with the capability of driving a large number of discrete devices simultaneously. The aim of this paper is to obviate these two requirements. First, different factors affecting the unbalanced voltage sharing between the series switches are discussed. In this investigation, the switch-to-ground parasitic capacitance effect has been recognized as the major effect on the unbalanced voltage sharing in the transient interval. Two schemes for abating this effect are proposed. To solve the unbalanced voltage distribution, the structure with a snubber circuit in the clamp mode operation is suggested. This scheme can be used for any number of switches without destructively affecting their behavior. In addition, the output pulse with a fast rising time could be obtained by the proposed gate drive system. In order to evaluate the operation of the proposed structure, a stacked switch with the voltage capability of 36 kV is tested experimentally. The characteristics of the obtained pulse are the fast rising time (69.5 ns) with the dV/dt of 460 kv/ \mu \texts and the wide range of the pulsewidth adjusting to 0.5–15 \mu \texts . In addition, the voltage variance of the switches level in the series structure is about 10%. [ABSTRACT FROM AUTHOR]

This paper details the experimental evaluation and simulation of a 4-kV n-type gate turn-OFF thyristor (GTO) designed for pulsed power applications. The primary criteria of evaluation are rate of current rise ( dI/dt ), turn-ON delay time ( T_{D}) , and resistance of the device during turn-ON transients [ R_{\mathrm{\scriptscriptstyle ON}}(t)$ ]. The device under test (DuT) is an n-type asymmetric-blocking GTO manufactured by Silicon Power (Part No. 14N40A10) with a rated dc blocking voltage of 4 kV. A test circuit was specifically designed to minimize stray inductance in order to capitalize on the dI/dt$ capabilities of the DuT. Experimental data collected from resistance measurements are used to develop a single-switch approximate model for use in simulation. The results of dI/dt$ experiments provide a profile of DuT dI/dt$ operation beyond rated values; specifically dI/dt were readily achieved. The turn-ON delay time of the DuT is also characterized and determined to be $\sim 225$ ns on average. [ABSTRACT FROM AUTHOR]

The superconducting inductive pulsed-power supply (SPPS) circuit consists of a high-temperature superconducting pulsed-power transformer (HTSPPT) and an auxiliary capacitor. The electrical losses and the power of the primary source can be cut down with the superconducting inductive energy storage. Although its energy density is slightly less than a purely superconducting inductive system, it can reduce the maximum voltage of the opening switch by the capacitor and achieve a high degree of current amplification factor. However, during the discharge process, the magnetic leakage flux energy stored in the primary of the HTSPPT requires the capacitor to have a certain capacity. The higher the ratio of the capacitive stored energy over the total inductive stored energy, the more the dominant position of inductive energy storage reduces. The current amplification factor ( \gamma ), the maximum voltage of the opening switch ( V_{S\max } ), and the ratio of capacitive stored energy ( \eta ) are the three main properties of the SPPS circuit, which depends on several intertwined critical parameters, such as the inductance ratio n = L2 /( L2+LL ) and the capacitance ( $C_{{\mathbf {1}}}$ ). This paper studies the influence of the critical parameters on the main circuit performance with a 1-kJ SPPS system. The detailed selection method of the critical parameters for the specific system is also discussed with a coupling coefficient of 0.95. Such a system is easy to be utilized for the basic experimental study of a small railgun. [ABSTRACT FROM PUBLISHER]

Many approaches exist for energy storage and delivery to the load, including high-power relativistic applications. One of the best solutions for the driver of high-power relativistic applications is the Marx generator. This paper describes the design, fabrication, and experimental validation of a Marx generator consisting of capacitors, spark-gap switches, and resistors. It is designed as an eight-stage Marx circuit to reach an output voltage level as low as −500 kV, and it is directly connected to the Blumlein pulse-forming line (PFL) to achieve more than 100 ns of the full-width at half-maximum. Experiments are performed with a solution load in a manner similar to having a coaxial structure in a high vacuum with a pressure of below 0.5\, \times \, 10^-5 torr, to prevent breakdown and measure the amplitude of the negative high-voltage pulse waveform. The solution load is designed to capture the short-pulse output of the PFL with a rise time of less than 25 ns and a voltage level of approximately −500 kV. The experimental results show that the output pulse can be used as a source to generate an intense relativistic electron beam at the gun for high-power relativistic applications. [ABSTRACT FROM PUBLISHER]

High-performance trigger generators with high amplitude, fast rise time, low jitter are essential for large-scaled pulsed-power systems. Most of the trigger generators are also tiny multistage pulsed-power systems with complicated structures. In this paper, a high-performance trigger generator was proposed by combining the advantages of low-jitter semiconductor switch and high-power gas switch. An avalanche transistor Marx circuit was developed. It was used to trigger a two-stage Marx generator based on trigatron switch. The output characteristics of the Marx circuit based on avalanche transistors and the two-stage Marx generator were studied. The experimental results show that a subnanosecond jitter, nanosecond rise time, high-voltage trigger generator can be achieved by triggering trigatron switch with an avalanche transistor circuit. [ABSTRACT FROM PUBLISHER]

Two-electrode graphite spark gap switch (TGSGS) is used as the main discharge switch and triggered by a reliable trigger generator in pulsed power conditioning system (PPCS). There would be 108 energy modules in PPCS working at the same time. The reliable operating and jitters of the trigger generators will have impact on the PPCSs performance. In this paper, the working modes of the TGSGS are discussed and the performance of trigger generators in PPCS is tested and presented. A protection strategy of the trigger generator in PPCS is introduced, and effect of the blocking capacitor on the trigger pulse transmission is analyzed and tested. The protection strategy of the trigger generator based on blocking capacitor and fuse can effectively prevent the energy anti-irrigation failure when the pulse transformer core saturated. The blocking capacitor has some effect on the trigger pulse transmission, and has the larger capacitance, getting the higher peak amplitude on the cathode of the TGSGS. It is tried to discuss the working characteristics of the thyristors, and proposes a selection reference of the thyristors in this and other similar applications. The combination of analysis and measurement would be useful for the selection of thyristors and other components. [ABSTRACT FROM PUBLISHER]

A repetitive 0.6 MV, 10 GW Tesla-driven Blumlein pulsed power generator, with an overall energy efficiency in excess of 90%, has been designed, manufactured and demonstrated by the Pulsed Power Group at Loughborough University. This paper describes the application of various numerical techniques used to design a successful generator, such as filamentary modeling and electrostatic and transient circuit analysis. All the major parameters of both the Tesla transformer and the Blumlein pulse-forming line were determined, enabling accurate modeling of the overall unit to be performed. The wide-bandwidth embedded sensors used to monitor the dynamic characteristics of the overall system are also presented. Experimental results obtained during this major experimental program are compared with theoretical predictions and the way ahead toward generating faster output voltage impulses is considered. [ABSTRACT FROM PUBLISHER]

Utilization of power electronics converters in pulsed power applications introduced a new series of reliable, long life, and cost-effective pulse generators. However, these converters suffer from the limited power ratings of semiconductor switches, which necessitate introduction of a new family of modular topologies. This paper proposes a modular power electronics converter based on voltage multiplier as a high voltage pulsed power generator. This modular circuit is able to generate flexible high output voltage from low input voltage sources. Circuit topology and operational principles of proposed topology are verified via experimental and simulation results as well as theoretical analysis. [ABSTRACT FROM PUBLISHER]

Starting from the updated requirements of an advanced laser system, a switch–trigger system for a 2.0-MJ pulsed power supply (PPS) module is developed. This paper discusses the design, construction, and testing of this switch–trigger system. The two-electrode construction for the spark gap switch is selected because of its superiority in terms of long working life, high peak currents, and fast rise time of currents. The trigger generator based on resonant charging of a pulse transformer is constructed. A magnetic isolator and a pressure controller are the auxiliary equipment of this system. In the section based on mathematical principles, the equations of the lifetime and stability of this spark gap switch with graphite electrodes are given. These expressions can be regarded as the design basis of the same type of switch. As for the trigger generator, the analysis states that an appropriate ratio can be obtained when using the resonant charging based on a core-type pulse transformer. The charging time is dependent on the leakage inductance and the capacitance of the primary and secondary capacitors. Extensive testing proves the operating parameters of the switches and the trigger generator. The measured discharge current waveform of the 2.0-MJ capacitive PPS module is demonstrated to be over 500 kA peak current and 500 \mus pulse width. The life test proves that the switch–trigger system can support more than 200 kC transfer charge. By replacing the electrodes, the lifetime of this switch can be extended furthrer. [ABSTRACT FROM PUBLISHER]

In this paper, we describe a novel multiple-switch pulsed-power technology. The basic idea is that the heavy switching duty is shared by multiple switches. The multiple switches are interconnected via a transmission line transformer, in such a way that all switches can be synchronized automatically and no special external synchronization trigger circuit is required. It can produce either exponential or square pulses, with various voltage and current gains and with a high degree of freedom in choosing output impedances. The topology has been implemented on a prototype with ten spark-gap switches. Pulses with a rise time of 10 ns, a width of 55 ns, a peak power up to 810 MW, a peak voltage of 77 kV, and a peak current of 11 kA have been achieved at a repetition rate of 300 pps. The energy efficiency of the circuit is about 93%. In addition to spark gaps, any overvoltage-controlled switch can be applied in this topology. As an example, we demonstrate the synchronous switching of multiple thyristor switches for current multiplication. The proposed multiple-switch topology can also be applied in a Blumlein configuration for an inductive voltage adder and a linear transformer driver. [ABSTRACT FROM AUTHOR]

In this paper, starting from the project requirements, a 1.2-MJ pulsed power supply (PPS) module for a high-power laser system has been developed. The main circuit of this module consists of a high energy density capacitor bank, a spark gap switch, a magnetic switch, a trigger generator, and a load subsystem. Due to the superiority in the stability and service life, the two-electrode construction for the spark gap switch, high peak currents, and rise time of the currents is selected. Since a two-electrode spark gap switch has no separate trigger electrode and must be directly overvolted by the trigger generator, a small Marx generator has been designed and constructed for the advantage of the proven compactness and electrical performance. The effect of the magnetic switch represents a couple of functions. One is to block the triggering pulse produced by the Marx generator. Another is to permit the discharging current coming from the main capacitor bank. Finally, the measured discharge current waveform of the 1.2-MJ capacitive PPS module is demonstrated to be over a 300-kA peak current and a 500- \mu\s pulsewidth. Moreover, the life test has proved that the switch–trigger system can support more than 1500 discharging processes. [ABSTRACT FROM AUTHOR]

This paper presents a novel crowbar system of 10/350-\mu\s pulse current. The crowbar pulse current system includes a crowbar pulse current waveform forming circuit, a controlling unit, and a measuring unit. The crowbar pulse current circuit consists of a main air triggered switch, a triggered vacuum switch (TVS) which is used as the crowbar switch, and two trigger signal generators. A kind of TVS is designed and fabricated. Its triggering characteristics are tested, and experimental results show that, compared with other reported similar switches, the TVS has excellent characteristics such as wide operating voltage scope from 1.3 to 120 kV, short discharging delay time with maximum delay time at 400 ns, and its jitter at \pm10 ns. Based on the TVS, the crowbar 10/350- \mu\s pulse current circuit and its controlling circuit are designed. With a 36-\mu\F storage capacitor C and a 6-\mu\H waveform forming inductance L, a 10/350- \mu\s pulse current waveform with a maximum of 150 kA can be generated. [ABSTRACT FROM AUTHOR]