Search

This paper analyzes priority-based distributed access control in vehicular networks. Characterizing the spatial correlation between vehicles, users, and roads, this paper uses Cox point processes to model vehicles and users, respectively. Then, this paper proposes that each vehicle transmits if it has the highest priority among all of its neighbors. Using the stochastic geometry framework, this paper derives the probability that a typical vehicle is retained to transmit. Then, this paper derives a second-order moment measure of the retained point process to evaluate the signal-to-interference (SIR) distribution of a typical user. The derived SIR distribution is compared to the system-level simulation of the SIR distribution of a typical user. [ABSTRACT FROM AUTHOR]

To exploit richer spectrum resources for even better service quality, millimeter wave (mmWave) communication has been considered for high-speed railway (HSR) communication systems. In this paper, we focus on scheduling as many flows as possible while satisfying their QoS requirements. Due to interference, eavesdropping, or other problems, some flows may not be directly transmitted from the track-side BS. In this paper, we propose an UAV-assisted scheduling scheme which utilizes a UAV to serve as relay for such flows. The proposed scheme also utilize two mmWave bands, one for the BS links and the other for the UAV links. The proposed algorithm aims to maximize the number of flows with their QoS requirements satisfied. Simulations demonstrate that the proposed scheme achieves a superior performance on the number of completed flows and the system throughput over two baseline schemes. [ABSTRACT FROM AUTHOR]

The aspects of sum rate and fairness for dirty paper coding (DPC) based MIMO downlink communications are investigated in this paper. We first apply the $\ell _{1}$ -norm fairness measure to formulate the problem of fairness maximization for a given sum rate as an optimization problem. The problem is unfortunately nonconvex and cannot be efficiently solved. To overcome the difficulty, we invoke the uplink-downlink duality to transform the problem back and forth between uplink and downlink communications. An efficient, iterative waterfilling based algorithm is then proposed to yield achievable rates with the best possible fairness values. Simulation results show that the proposed approach offers an enormous gain in the achievable sum rates for a wide range of fairness values, when compared to the popular successive zero-forcing DPC-based and block diagonalization based coding schemes. [ABSTRACT FROM AUTHOR]

The explosive growth of Internet-of-Things (IoT) applications such as smart cities and Industry 4.0 have led to drastic increase in demand for wireless bandwidth, hence motivating the rapid development of new techniques for enhancing spectrum utilization needed by new generation wireless communication technologies. Among others, dynamic spectrum access (DSA) is one of the most widely accepted approaches. In this paper, as an enhancement of existing works, we take into consideration of inter-node collaborations in a dynamic spectrum environment. Typically, in such distributed circumstances, intelligent dynamic spectrum access almost invariably relies on self-learning to achieve dynamic spectrum access improvement. Whereas, this paper proposes a DSA scheme based on deep reinforcement learning to enhance spectrum and access efficiency. Unlike traditional Q-learning-based DSA, we introduce the following to enhance the spectrum efficiency in dynamic IoT spectrum environments. First, deep double Q-learning is adopted to perform local self-spectrum-learning for IoT terminals in order to achieve better dynamic access accuracy. Second, to accelerate learning convergence, federated learning (FL) in edge nodes is used to improve the self-learning. Third, multiple secondary users, who do not interfere with each other and have similar operation condition, are clustered for federated learning to enhance the efficiency of deep reinforcement learning. Comparing with the traditional distributed DSA with deep learning, the proposed scheme has faster access convergence speed due to the characteristic of global optimization for federated learning. Based on this, a framework of federated deep reinforcement learning (FDRL) for DSA is proposed. Furthermore, this scheme preserves privacy of IoT users in that FDRL only requires model parameters to be uploaded to edge servers. Simulations are performed to show the effectiveness of theproposed FDRL-based DSA framework. [ABSTRACT FROM AUTHOR]

Absolute time synchronization is a basic issue in wireless communication. With the advent of 5G, many emerging vertical industry applications have put forward demands for timing accuracy over air interface. High Precision Timing method over Air Interface based on PHY Layer Signals (TAP) is proposed for mobile networks. It is designed to provide microsecond level timing accuracy at a relatively low cost compared to the existing timing methods, such as GNSS, NTP, PTP, etc. The purpose of this paper is to comprehensively improve TAP, including timing accuracy, stability and compatibility, so as to promote its practical application. This paper proposes improvements to TAP from four aspects: timing algorithm, timing pilot signal, terminal timing process and timing parameters determination. We improve the TAP’s deficiencies in delay estimation, delay compensation accuracy and real-time matching of timing information. We implement the workflow of TAPv2 for UE based on FPGA. Finally, we settle the problem of TAP parameters determination by applying a DQN method. The simulations and tests not only show that the DQN model can effectively determine the TAP parameters, but also show TAPv2 can achieve higher accuracy and stability than TAP in multiple scenarios based on the interaction with baseband. [ABSTRACT FROM AUTHOR]

Due to the non-uniform geographic distribution and time-varying characteristics of the ground traffic request, how to make full use of the limited beam resources to serve users flexibly and efficiently is a brand-new challenge for beam hopping satellite systems. The conventional greedy-based beam hopping methods do not consider the long-term reward, which is difficult to deal with the time-varying traffic demand. Meanwhile, the heuristic algorithms such as genetic algorithm have a slow convergence time, which can not achieve real-time scheduling. Furthermore, existing methods based on deep reinforcement learning (DRL) only make decisions on beam patterns, lack of the freedom of bandwidth. This paper proposes a dynamic beam pattern and bandwidth allocation scheme based on DRL, which flexibly uses three degrees of freedom of time, space and frequency. Considering that the joint allocation of bandwidth and beam pattern will lead to an explosion of action space, a cooperative multi-agents deep reinforcement learning (MADRL) framework is presented in this paper, where each agent is only responsible for the illumination allocation or bandwidth allocation of one beam. The agents can learn to collaborate by sharing the same reward to achieve the common goal, which refers to maximize the throughput and minimize the delay fairness between cells. Simulation results demonstrate that the offline trained MADRL model can achieve real-time beam pattern and bandwidth allocation to match the non-uniform and time-varying traffic request. Furthermore, when the traffic demand increases, our model has a good generalization ability. [ABSTRACT FROM AUTHOR]

This paper provides a comprehensive performance comparison between a current robust military waveform; namely, MIL-STD-188-110D, Waveform 0, and a filter bank multicarrier spread-spectrum (FBMC-SS) waveform proposed for communications through ionospheric/skywave HF channels. Waveform 0 is effectively a direct sequence spread spectrum waveform that uses Walsh multi-codes to enhance the information transmission rate. It may thus be referred to as Walsh-DSSS. FBMC-SS, on the other hand, makes use of filter banks to provide excellent performance when the received signal is subject to partial band interference. Successful application of FBMC-SS for communications across skywave HF channels has been previously demonstrated, both theoretically and through experimental work. However, very little has been done to contrast FBMC-SS against Walsh-DSSS. The goal of this paper is to first add new features to FBMC-SS to bring it on par with Walsh-DSSS. These features include: (i), introduction of multi-codes that achieve a comparable (or better) data rate to Walsh-DSSS; and (ii), addition of a scrambling step applied to the multi-codes to make the receiver detection robust against widely spread multipaths. With this established, in the second part of the paper, we examine the performance of the developed FBMC-SS against Walsh-DSSS when both are applied for communications across skywave HF channels. The two waveforms are compared both through a theoretical study and through experimental works across several skywave channels ranging from hundreds to thousands of kilometers. [ABSTRACT FROM AUTHOR]

The paper studies a reconfigurable intelligent surface (RIS)-assisted multi-user uplink massive multiple-input multiple-output (MIMO) system with imperfect hardware. At the RIS, the paper considers phase noise, while at the base station, the paper takes into consideration the radio frequency impairments and low-resolution analog-to-digital converters. The paper derives approximate expressions for the ergodic achievable rate in closed forms under Rician fading channels. For the cases of infinite numbers of antennas and infinite numbers of reflecting elements, asymptotic data rates are derived to provide new design insights. The derived power scaling laws indicate that while guaranteeing a required system performance, the transmit power of the users can be scaled down at most by the factor $\frac{1}{M}$ when $M$ goes infinite, or by the factor $\frac{1}{MN}$ when $M$ and $N$ go infinite, where $M$ is the number of antennas and $N$ is the number of the reflecting units. Furthermore, an optimization algorithm is proposed based on the genetic algorithm to solve the phase shift optimization problem with the aim of maximizing the sum rate of the system. Additionally, the optimization problem with discrete phase shifts is considered. Finally, numerical results are provided to validate the correctness of the analytical results. [ABSTRACT FROM AUTHOR]

In complex indoor environments, there is often no Line of Sight (LOS) path between the transmitter and the receiver due to walls, moving people, and many other obstacles. Traditional localization method based on LOS measurement is no longer available which provides lower localization accuracy in Non-Line of Sight (NLOS) environments. In response to this problem, this paper proposes a joint localization algorithm for scatterers and target user based on indoor prior information in NLOS scenarios. The algorithm makes use of the prior localization information of the access point (AP) and the wall to determine the position of the scatterers and target user simultaneously. Since the established constrained optimization problem is non-convex which is a difference of convex (DC) problem, it is transformed into a convex one based on a Taylor series expansion (TSE) method before it is solved. At the same time, as only a single AP signal can be received normally, the proposed method is then extended to the scenario with only one AP. Simulation and real-world testing results both show that not only the proposed method based on multiple APs, but also the method based on a single AP achieve high positioning accuracy, which are better than the existing positioning methods mentioned in this article as well. [ABSTRACT FROM AUTHOR]

Radio signal recognition has a wide application in future communication systems and the vehicular communication, whose core is the extraction of signal features such as electromagnetic fingerprints. With the rapid development of artificial intelligence technology, deep learning has made amazing breakthroughs in image recognition, speech recognition and other fields. Deep learning is applied to electromagnetic fingerprint extraction in this paper. Firstly, thousands of the downlink aircraft communications addressing and reporting system (ACARS) signals used for communication between civil aircraft and airport tower are collected and generated. Then a pre-transformation network suitable for electromagnetic signals is constructed to convert one-dimensional signals into two-dimensional feature maps, and afterwards the feature maps are input into the convolutional neural network (CNN) for classification. By adopting the attention modules, the classification results were improved by a few percentage points over the baseline with a little cost. The method proposed in this paper achieves an accuracy rate of 94.1% and can obtain the aircraft type in a shorter time than traditional method. Moreover, the robustness of the proposed model in response to additive Gaussian white noise (AWGN) and phase deviation is studied and tested. [ABSTRACT FROM AUTHOR]

Millimeter-wave rotary-wing (RW) unmanned aerial vehicle (UAV) air-to-ground (A2G) links face unpredictable Doppler effect arising from the inevitable wobbling of RW UAV. Moreover, the time-varying channel characteristics during transmission lead to inaccurate channel estimation, which in turn results in the deteriorated bit error probability performance of the UAV A2G link. This paper studies the impact of mechanical wobbling on the Doppler effect of the millimeter-wave wireless channel between a hovering RW UAV and a ground node. Our contributions of this paper lie in: i) modeling the wobbling process of a hovering RW UAV; ii) developing an analytical model to derive the temporal autocorrelation function (ACF) for the millimeter-wave RW UAV A2G link in a closed-form expression; and iii) investigating how RW UAV wobbling impacts the Doppler effect on the millimeter-wave RW UAV A2G link. Numerical results show that different RW UAV wobbling patterns impact the amplitude and the frequency of ACF oscillation in the millimeter-wave RW UAV A2G link. For UAV wobbling, the temporal ACF decreases quickly and the impact of the Doppler effect is significant on the millimeter-wave A2G link. [ABSTRACT FROM AUTHOR]

The use of antenna arrays is indispensable in radar and multiple-input multiple-output (MIMO) wireless communications areas, as it permits the treatment of wavefronts in the spatial domain, enabling important applications such as beamforming and target detection. Spatial information is commonly given in terms of spatial correlation functions (SCFs), but its representation in terms of angular domain, such as the power azimuth spectrums (PASs), is sometimes more convenient. Therefore, transforming from SCF to PAS, and vice versa, is often required. This is commonly done by employing so-called beamformers, where the Bartlett beamformer (BB) is the most commonly utilized. However, the use of beamformers alone is not enough for retrieving PAS information from a given SCF. Particularly, this paper shows that a non-linear operation is missing in relating SCFs to PASs as provided by current beamformers. The paper also shows the mathematical expressions that correctly relate SCFs to PASs and wavenumber spectrums (WNSs) for the general case of systems with antenna arrays. The developed theory results in two new beamformers, which, corroborated by simulation results, solve any previous inconsistency in estimating PASs from SCFs. [ABSTRACT FROM AUTHOR]

Factor graph optimization (FGO) is a well-known approach in the robotics field. Due to multiple iterations and application of large amounts of data, it usually could superior performance than the Kalman Filter (KF) under complex scenarios. However, it is rarely used in the underwater environment, especially for applications based on fiber-optic inertial navigation. Taking the ultra-short baseline system (USBL) as the application background, a novel inertial navigation system (INS)/USBL integrated navigation scheme based on FGO is presented in this paper. The traditional pre-integration factor simplifies the earth rotation and coordinate system, which limits its application in high-precision sensors. This paper proposed an improved pre-integration model using the high precision measurements of fiber optics gyroscope in FGO. Simulation and field tests proved that, with the FGO method, improved accuracy of INS/USBL integration was obtained compared to the traditional KF method. It confirms the potential of FGO in the applications of underwater navigation and positioning. [ABSTRACT FROM AUTHOR]

In order to achieve the purpose of extending the speed range and reducing power electronics devices for the permanent-magnet linear motor drive system, a half-centralized open-end winding (OEW) topology is studied for rail transit applications in this paper. In this topology, compared with the traditional OEW topology, the number of voltage-source-inverters (VSIs) can be reduced from four to three to drive two OEW movers and all these VSIs share a common dc bus voltage. In order to improve the steady-state performances, a four-vector phase model predictive voltage control (FV-PMPVC) is proposed in this paper. Due to the spatial distribution of phase voltage vector (PVV), an orthometric synthesis principle (OSP) is proposed to calculated the duration time for the vector synthesis, which reduces the computation burden and enhances the robustness. Comparing the existing control method, FV-PMPVC can get similar dynamic performances but better steady-state performances. Additionally, the half-centralized topology using FV-PMPVC can have same speed range while less VSIs are required. The effectiveness of FV-PMPVC is verified by experimental results. [ABSTRACT FROM AUTHOR]

Wireless channel characterization and modeling is the foundation of vehicular communication systems. However, most of the existing researches on vehicle-to-vehicle (V2V) channel are aimed at the traditional scenarios such as urban and suburban, and the researches on some complicated vehicular scenarios are insufficient. For example, little attention is paid to viaduct, tunnel, and cutting scenarios in vehicular communications, and these complex scenarios often become the high-incidence area of communication interruption, and then affect the overall performance of the vehicular communication system due to the bad and unique channel characteristics. In this paper, to fill this gap, time-varying characteristics of V2V channels in viaduct, tunnel, and cutting scenarios are investigated. Specifically, based on 5.9 GHz channel measurements, channel non-stationarity is quantitatively evaluated and compared. Further, a detailed analysis of time-varying power and delay of multipath components (MPCs) is presented. Based on the obtained results, the mechanism of physical environment affecting channel characteristics is analyzed, and the impacts of vehicular scenarios are quantified. Besides, the impacts of scenarios on the spatial distribution of MPCs are investigated. The angular distributions of MPCs in the three typical V2V scenarios are revealed, and the corresponding statistical characteristics are presented. Moreover, the characteristics of MPC clusters in different scenarios are further quantified and analyzed, such as MPC number in each cluster and cluster lifetime. It is revealed that the non-stationarity of the V2V channel originates from the birth-death process of MPC clusters, and the birth-death process is modeled statistically. The results in the paper show the V2V channel propagation mechanism and can be used for the design of vehicular communication systems in complicated scenarios. [ABSTRACT FROM AUTHOR]

The article presents the discussion on predictive energy management strategy of plug-in hybrid electric vehicles by real-time optimization and data-driven calibration. Topics include relating to road vehicles, the electrification of railway vehicles, air and water vehicles requiring fast development in combating the global climate change; and criteria for fuel cell operation finding the best trade-off between hydrogen consumption and number of start-ups.

This paper proposes on-driving experience sharing algorithms at junctions in infrastructure-assisted vehicles-to-everything networks. For the purpose, a millimeter-wave (mmWave) technology is used because it provides multi-Gbps data rates which is helpful for handling users’ short stay times at junctions and spatial reuse due to high beam directionality which is helpful for interference-avoidance among densely deployed vehicles at junctions. To realize on-driving experience sharing, the proposed algorithms focus on joint resource allocation and scheduling for 3GPP-compliant multiple unicast vehicle-to-vehicle (V2V) communications where the vehicles are group leaders (GLs) in 3GPP Mode 4(d). The resource allocation stands for the roadside unit (RSU) allocation to scheduled V2V GL links where RSU is essentially required for overcoming blockage by establishing two-hop relaying. Because vehicles stay for short times at junctions, this paper designs two algorithms without or with delay considerations. Without delay considerations, the joint optimization of RSU allocation and scheduling was originally formulated as mixed 0-1 non-convex optimization. However our proposed algorithm reformulates the problem into mixed 0-1 convex optimization, which is computationally easier to solve. With delay considerations, our proposed algorithm dynamically controls video contents frame rates for time-average on-driving video sharing quality maximization subject to delay constraints, inspired by Lyapunov optimization. Extensive simulation results demonstrate that our algorithms can significantly outperform in a variety of scenarios. Furthermore, we conduct the cost analysis for the proposed algorithms in terms of capital expenditure (CAPEX) and operating expenditure (OPEX). [ABSTRACT FROM AUTHOR]

The age of information (AoI) is a key performance metric for data freshness in real-time systems, measuring the time elapsed between status updates received at a remote destination. This paper addresses the analysis of both the AoI and the delay for a system demanding timely status updates, consisting of an internet of things (IoT) community, and a multi-core edge computing node (EN). The IoT devices perform channel contention according to a slotted aloha non-orthogonal multiple access scheme with two transmission power levels to access the EN. The objective of the paper is the dynamic selection of both the EN computation capabilities and the suitable access probability for the two power levels, aiming at maximizing the time-average system utility, while guaranteeing the queues stability. The device end-to-end delay is analyzed by resorting to the martingale theoretical approximation under the condition that the Lyapunov optimization framework is performed on a time slot basis, hence leading to a novel instantaneous mixed integer problem formulation. Furthermore, the generalized benders decomposition method is employed to provide a suboptimal solution for the formulated problem. Finally, the accuracy of the proposed framework is validated by comparing the obtained analytical predictions with simulation results. [ABSTRACT FROM AUTHOR]

In this paper, we consider an energy efficient resource allocation technique for a hybrid time division multiple access (TDMA) - non-orthogonal multiple access (NOMA) system. In such a hybrid system, the available time for transmission is divided into several sub-time slots, and a sub-time slot is allocated to serve a group of users (i.e., cluster). Furthermore, signals for the users in each cluster are transmitted based on the NOMA approach. With NOMA, multiple users can be served simultaneously through utilizing power domain multiplexing at transmitter and successive interference cancellation (SIC) at receiver. In this paper, to maximize the energy efficiency (EE), we jointly allocate both the available time slots and the available transmit power in the hybrid TDMA-NOMA system. In particular, we formulate an EE maximization (EE-Max) problem aiming to maximize the overall EE of the system with a per-user minimum rate and transmit power constraints. However, this joint optimization problem is non-convex in nature, and thus, cannot be solved directly. Therefore, we develop an iterative algorithm by approximating the original problem into a convex one with sequential convex approximation (SCA) and a novel second-order cone (SOC) approach. Simulation results demonstrate that the performance of the proposed hybrid TDMA-NOMA system with joint resource allocation outperforms the system with equal time allocation in terms of the overall EE. Simulation results further confirm that the proposed iterative approaches with SCA and SOC techniques converge within a few number of iterations while yielding the solution to the original non-convex problem. [ABSTRACT FROM AUTHOR]

With the advancement of wireless communication technologies and rich embedded sensors in smart mobile devices, mobile crowdsensing has become an attractive paradigm for collecting sensing data from surrounding environments. Effective incentive mechanisms often play an important role in guaranteeing high quality of services and wide involvement of workers. Much work has been carried out in this aspect to encourage workers to strenuously and truthfully provide high quality data. However, task quality does not only depend on workers’ subjective effort or truthfulness, but also workers’ distribution and task quality growth law. In this paper, we consider a scenario where worker arrivals are unevenly distributed and the growth of task quality conforms to the law of diminishing margin of workers’ efforts. We propose a Quality-driven Online Task-Bundling-based incentive mechanism (QOTB). The design objective is to maximize the social welfare while maximally satisfying the task quality requirements. In QOTB, we introduce Mental accounting Theory to build accounts for task execution profit and bonus, respectively, which are then used to derive the participation willingness of workers. We adopt task bundling to stimulate workers to change their original travel schedules for balancing the task participations according to the popularities of task locations and also the traveling cost. We present the detailed mechanism design of QOTB. We prove that the QOTB mechanism has desired properties of willingness truthfulness, individual rationality, and computation efficiency. We conduct extensive simulations and the results show that QOTB can effectively improve the social welfare while satisfying the task quality requirements. [ABSTRACT FROM AUTHOR]

Future communication networksrequire higher bandwidth, greater coverage, and better throughput. The Space-Air-Ground Integrated Network (SAGIN) has the advantage of wide-area coverage and can cover global communications. It can meet the needs of network resources for maritime activities and remote mountainous areas, which is of great significance to the realization of a new generation of communications networks. With the development of the network and the emergence of delay-sensitive applications such as the Internet of Things, improving the delay performance of the system has received extensive attention. SAGIN involves multiple networks and is more complex than other networks. If there is no reasonable management between different networks, it is easy to lead to difficult link deployment and high time delay. On the basis of research and customization of SFC technology, it can provide a wide range of services and other advantages. It has significant performance in application scenarios involving multi network integration. In order to solve the above problems, this paper studies the SAGIN architecture of SFC based on business types. A service function chain mapping method based on delays prediction is proposed. Calculate the delay of the deployment path and select the path with the lowest delay as the SFC mapping path. The service model is constructed according to the mapping path, and the network slices are divided based on the service type. The simulation results show that the SFC mapping algorithm based on time delay prediction is compared with the traditional SFC mapping scheme. The algorithm does not affect other indicators, the CPU resource utilization rate is 27.8 $\%$ higher, and the link resource utilization rate is 22.7 $\%$ higher. The service acceptance rate increased by 21.5 $\%$ , the latency performance increased by 38.2 $\%$ , and the total resource consumption is reduced by 25.2 $\%$. [ABSTRACT FROM AUTHOR]

This paper proposes a traction unit that combines an interior permanent magnet motor and a PM-assisted synchronous reluctance motor for electric vehicles to improve traction performance, enhance energy efficiency, and reduce cost. The characteristics of three traction units are analyzed and compared, including (a) rear-wheel-drive configuration using one IPM motor; (b) all-wheel-drive configuration using two interior permanent magnet motors; and (c) all-wheel-drive with a combination of one interior permanent magnet motor and one PM-assisted synchronous reluctance as proposed in this paper. The operational characteristics of each motor to achieve a wide constant power speed range are first investigated. Then, the Urban Dynamometer Driving Schedule is utilized to compare and evaluate the operational characteristics, energy consumption, and most importantly, the efficiency of the traction units. Simulation results reveal that the overall efficiency of the proposed traction unit can be improved compared to the other configurations. The advantages and drawbacks of the proposed traction unit are also investigated. Finally, experiments are conducted to validate the analysis. [ABSTRACT FROM AUTHOR]

In the controller development process, it is required to verify whether control functions operate normally, without fault or anomaly. Many control functions with complex system structures require various actual tests and test data analysis for verification. This paper presents an anomaly detection algorithm to verify control functions and to more efficiently analyze test data of a hybrid control unit (HCU) of a hybrid electric vehicle (HEV). The anomaly detection algorithm automatically detects anomaly of control functions from the test data, instead of manual labor by engineers. The examined target HCU control functions in this paper are the engine clutch engagement/disengagement control function and the engine start cooperative control function, which are crucial functions of transmission mounted electric drive (TMED) HEVs. A data-driven approach using a one-class support vector machine (SVM) is used to make it easy to apply various control functions. Actual vehicle test data is examined by the algorithm to verify the control functions at an actual vehicle level. The developed anomaly detection algorithm demonstrates feasibility and effectiveness of the proposed algorithm in detecting not only prior-known anomalies but also prior-unknown anomalies. Because other vehicle control functions have similar characteristics with the target functions of this paper, this algorithm is expected to be successfully applied to other HCU control functions. [ABSTRACT FROM AUTHOR]

In concurrent spectrum sharing scenarios between radars and wireless communication systems, one strict approach to protect the radar from undesired interference is locating the base stations outside a guard (or exclusion) zone of the radar. As a result, users inside that zone experience bad communication coverage. This paper uses Reconfigurable Intelligent Surfaces (RISs) to improve the base station coverage of users in the radar exclusion zone. The paper shows, through analysis and simulation, that joint optimization of base station and RIS locations improves the probability of coverage in the exclusion zone over the shared spectrum without disturbing the radar operation. [ABSTRACT FROM AUTHOR]

This paper proposes a model predictive current control (MPCC) method based on current augmenter prediction model (CAPM) appropriate for interior permanent magnet synchronous motor (IPMSM) under high-speed condition. The accuracy of CAPM is improved by considering rotor movement during one control period especially under high-speed condition. Meanwhile, the use of the permanent magnetic flux linkage is eliminated. In order to further improve the robustness of the MPCC method, an adaptive observer based on CAPM is designed to estimate the model error. The proposed adaptive observer also eliminates the use of the permanent magnetic flux linkage, so the whole implementation process of the MPCC method with adaptive observer is independent of the permanent magnetic flux linkage. Moreover, since the adaptive observer with fixed adaptive integral gain cannot achieve satisfactory performance under different operating conditions of the motor, this paper designs a calculation method for the variable adaptive integral gains by considering the current estimation error, the amplitude of current and the angular velocity of the IPMSM. Finally, the proposed method is validated by means of the experimental results on a 20-kW test platform. [ABSTRACT FROM AUTHOR]

In this paper, we develop a novel visual-inertial navigation system with motion constraint (VINS-Motion), which extends the visual-inertial navigation system (VINS) to incorporate vehicle motion information for improving the autonomous vehicles localization accuracy. We introduce the vehicle stop detection module in the pre-processing measurement procedure. During the back-end processing, if the vehicle is detected to be in a stopping state, we perform optimization based on the stop constraint to help eliminate the abnormal jitter of the estimated pose, thus ensuring the reasonability of the trajectory. Otherwise, besides the prior information, IMU measurement residual, and visual measurement residual utilized in VINS, vehicle orientation/velocity constraint built by Ackerman steering model is first exploited to constitute residuals. We minimize the sum of priors and Mahalanobis norms of three kinds of residuals to obtain a maximum posterior estimation, thus increasing system consistency and accuracy. The proposed approach is validated on public datasets and compared with state-of-the-art algorithms, which demonstrates that the motion constraint proposed in this paper improves the standard VINS performance and achieves significantly higher positioning accuracy. [ABSTRACT FROM AUTHOR]

Fixed Satellite Services (FSS) used to be alone at the C-Band spectrum in most countries. Since the deployment of 5G in many countries (i.e., 3.3–3.6 GHz), FSS is not the exclusive system in the C-Band anymore. In order to minimize the detrimental interference for the FSS to allowable levels, regional exclusion zones of maximum radiated power in 5G base stations (BS) are proposed and evaluated. In this paper, a measurement campaign has been carried out, and an analysis of the interference has been studied. A filtering model, namely Filter to Remove Broadband Interference 5G (FIREBRING), is proposed and analyzed concerning the carrier-to-noise ratio (C/N). Moreover, this paper focuses on the evaluation of the 5G interference into the FSS. The proposed solution deployed an Low-Noise Block (LNB) with a band frequency of 3.7 to 4.2 GHz to test the satellite down-conversion signal at the receiver. The paper offered a complete analysis of the 5G signal, taking into account the implications of out-of-band emissions, potentially LNB saturation into FSS receiver, and the repercussions of the deployment of the 5G BS active antenna systems. With the LNB and down-converter in place, it can be found that the signal interference between 1.450 GHz and 1.550 GHz, is nearly 18 dB. [ABSTRACT FROM AUTHOR]

This paper presents a decomposed co-design optimization framework for an electric vehicle powertrain equipped with a Continuously Variable Transmission (CVT). We jointly design the sizes of the powertrain components and the energy management strategy, considering the design and the dynamics of the transmission. Specifically, we divide the resulting nonlinear optimization problem into separate hierarchical optimization subproblems leveraging the concept of Analytical Target Cascading (ATC). Furthermore, we compare the proposed decomposition-based strategy with a centralized approach, in which we solve the same problem, and show that the method presented in this paper can be a potential alternative to a centralized optimization formulation for solving the large-scale, complex integrated plant and control system design. Finally, we compare the resulting performance of using a CVT on the vehicle total-cost-of-ownership with that equipped with a Fixed-Gear Transmission (FGT), which is what is commonly implemented in current electric vehicles. Our results show that by jointly optimizing the design of the transmission along with the control strategy, the CVT yields a lower energy consumption and total-cost-of-ownership compared to that of the FGT. [ABSTRACT FROM AUTHOR]

An editorial is presented on Cybertwin supporting advanced vehicle-to-everything (V2X) applications in the future intelligent and securing vehicular 6G network. Topics include becoming the personal AI assistant and acting as a security agent through customizing the visibility of recorded data; and proposing scheme good security performances in terms of symbol error rate (SER) and secrecy outage probability.

As more and more people choose high-speed rail (HSR) as a means of transportation for short trips, there is ever growing demand of high quality of multimedia services. With its rich spectrum resources, millimeter wave (mm-wave) communications can satisfy the high network capacity requirements for HSR. Also, it is possible for receivers (RXs) to be equipped with antenna arrays in mm-wave communication systems due to its short wavelength. However, as HSRs run with high speed, the received signal power (RSP) varies rapidly over a cell and it is the lowest at the edge of the cell compared to other locations. Consequently, it is necessary to conduct research on RX beamforming for HSR in mm-wave band to improve the quality of the received signal. In this paper, we focus on RX beamforming for a mm-wave train-ground communication system. To improve the RSP, we propose an effective RX beamforming scheme based on deep reinforcement learning (DRL), and develop a deep Q-network (DQN) algorithm to train and determine the optimal RX beam direction with the purpose of maximizing average RSP. Through extensive simulations, we demonstrate that the proposed scheme has better performance than the four baseline schemes in terms of average RSP at most positions on the railway. [ABSTRACT FROM AUTHOR]

Mechanical elastic wheel (MEW) has the advantage of explosion-proof, which helps to guarantee the safety and maneuverability of the automobile. Aiming to improve the stability of vehicles matching with MEW, this paper proposes an integrated control strategy that combines the active front steering and the active suspension systems. The integrated controller consists of feed-forward and feedback controllers. Firstly, the differential flatness system of the vehicle is constructed concerning the coupling among yaw, lateral, and roll motion. And the flatness based feed-forward control inputs of the desired front wheel angle and active roll moment are derived. At the same time, the backstepping-adaptive feedback controllers for yaw rate and roll angle are designed. Then, the feed-forward and feedback controllers are coordinated and their weight coefficients are adjusted according to the sideslip angle. Furthermore, this paper also adopts a nonlinear disturbance observer to estimate the vertical load of MEW. The influence of the vertical load is fully considered when estimating the equivalent cornering stiffness of each MEW, so as to realize the online adjustment of the controller parameters. Finally, the maneuver tests of step input steering and double lane change are simulated, respectively. The results show that the proposed control strategy yields a better control effect than the fuzzy-PID controller, and the performance of the vehicle matching with MEW has been significantly improved. [ABSTRACT FROM AUTHOR]

Indoor location-based services have become more and more important due to their potential applications in a wide range of personalized services in recent years. The accuracy of smartphone based 3D indoor localization is subjected to the poor performance of low-cost sensors and limited coverage of location sources. In order to solve these problems, this paper proposes a precise 3D indoor localization and trajectory optimization framework that uses the combination of sparse Wi-Fi Fine Time Measurement (FTM) anchors and built-in sensors (3D-LOWS). The inertial navigation system (INS) mechanization, multi-level constraints and observed values are integrated by the adaptive unscented Kalman filter to eliminate effects of cumulative error, indoor magnetic interference, and diversity of handheld modes. The Wi-Fi based ranging and landmark detection information is used to provide an accurate absolute reference to the built-in sensors based method. In addition, this paper proposes and evaluates two different trajectory optimization algorithms and compares the improved localization performance. The comprehensive experiments indicate that the proposed 3D-LOWS is proved to achieve accurate and stable 3D indoor positioning and trajectory optimization performance under complex indoor environments using sparse wireless stations. [ABSTRACT FROM AUTHOR]

The pantograph-catenary system is used in modern electrified railways to power electric trains. Common sense is that the increase of train speed leads to a deterioration of the interaction performance. But recent studies indicate that a higher speed may result in a better performance in some local speed regions. This paper is the first attempt to provide a theoretical explanation for this phenomenon. A validated pantograph-catenary model is built to reproduce this phenomenon. Referring the definition of critical speed in moving load problems, the catenary's critical speed is defined. The wavelength components can be extracted through the Fourier transformation to the contact wire's vertical mode shape. The speed that satisfies the resonance condition can be regarded as the potential critical speed. The corresponding contact wire amplitude is further evaluated to determine the critical speeds at a given mode. The analysis indicates that a good interaction performance happens when the speed falls in the transition procedure between the critical two speeds. Based on this idea, a simple indicator that describes the overall contribution of all modes subjected to a moving pantograph at a given speed is proposed to facilitate the determination of the local optimal speed. The variation of the proposed indicator with respect to the speed shows good consistency with the trend of the simulation results. The main finding in this paper can be used in the design phase to determine the optimal speed of the pantograph-catenary system in a local speed range. [ABSTRACT FROM AUTHOR]

Cooperative Intelligent Transportation Systems (C-ITS) will change the modes of road safety and traffic management, especially at intersections without traffic lights, namely unsignalized intersections. Existing researches focus on vehicle control within a small area around an unsignalized intersection. This paper expands the control domain to a large area with multiple intersections. In particular, a Multi-intersection Vehicular Cooperative Control (MiVeCC) is proposed to enable cooperation among vehicles in a large area with multiple unsignalized intersections. Firstly, a vehicular end-edge-cloud computing framework is proposed to facilitate end-edge-cloud vertical cooperation and horizontal cooperation among vehicles. Under the framework, a two-stage reinforcement learning is implemented to obtain the optimal policy for vehicle control. To support RL in the proposed framework, a multi-vehicle state representation method and a safety-oriented value representation method are designed. The former structures the collected vehicle information, and the latter evaluates the traffic condition. A multi-intersection simulation platform is developed to evaluate the proposed scheme. Simulation results show that the proposed MiVeCC can improve travel efficiency at multiple intersections by up to 4.59 times without collision compared with benchmark methods. [ABSTRACT FROM AUTHOR]

Uncertain cut-in maneuver of vehicles from adjacent lanes makes it difficult for vehicle's automatic speed control strategy to make judgments and effective control decisions. In this paper, an intelligent speed control strategy for uncertain cut-in scenarios is established based on a basic autonomous driving system. This strategy judges cut-in maneuver from surrounding vehicles and outputs adaptive control action under current environment according to Q value of state-action pair based on a Q network. In addition, according to the analysis of cut-in scenarios, the Q network is trained based on a novel reinforcement learning method named as experience screening deep Q-learning network (ES-DQN). The proposed ES-DQN is an extension of double deep Q-learning network (DDQN) algorithm, and includes two parts: experience screening and policy learning. Based on the experience screened from the experience screening part, the proposed learning method can train an intelligent speed control strategy which has stronger adaptability and control effect in uncertain cut-in scenarios. According to simulation results, the proposed intelligent speed control strategy trained by ES-DQN has better performance under uncertain cut-in scenarios than DDQN method and traditional ACC strategy. Meanwhile, by adjusting weight value in reward function, the system can realize different control target. [ABSTRACT FROM AUTHOR]

Electric vehicles (EVs) have attracted enormous attention in recent years due to their potentials in mitigating energy crisis and air pollutions. However, the long battery charging time and lack of sufficient charging infrastructure highly restrict the popularization of EVs. In this context, it is promising to establish battery charging and swapping systems (BCSSs) based on the concept of battery swapping services. To optimally achieve the combined operation of BCSSs, this paper proposes a hybrid swapped battery charging and logistics dispatch model in continuous time domain. Identifying the special structure of the mathematical models of the two problems, this paper innovatively formulated the swapped battery charging strategy as the rectangle packing problem and the battery logistics model as the vehicle routing problem. The two models are closely linked by the delivery time of transporting the well-charged batteries from battery charging stations to battery swapping stations. A hybrid optimal operation model of BCSSs is further formulated as a mixed-integer linear programming model by incorporating the interaction between the battery charging and battery logistics. Finally, case studies are conducted on several BCSSs and numerical results validate the effectiveness of the proposed model. [ABSTRACT FROM AUTHOR]

The performance of the recently proposed orientational beamforming (OBF) system for ultra-wideband (UWB) signals degrades seriously in multiuser situation. Although various techniques have been proposed in the literature to suppress multiuser interference in the time-hopping UWB system, there has been no research on interference suppression in the OBF UWB system. In this paper, we propose a nonlinear OBF system via a modified radial basis function (RBF) neural network, named the RBF-OBF system, to reject orientational UWB interferences caused by multiuser transmission in the OBF system. The RBF neural network is selected mainly because of its simple structure, convenient training process, and fast convergence speed. However, the conventional Euclidean-distance-based RBF neural network is not suitable for the training process used in this work, as the training samples are noiseless orientational steering vectors in frequency domain. Therefore, a modified RBF neural network is proposed in this paper, which evaluates the similarity between an input vector and the center vector of a hidden layer neuron by their signed complex correlation coefficient. Numerous simulations demonstrate that compared to the conventional OBF system, the proposed RBF-OBF system can significantly reduce the bit error rates (BERs) under different noise and interference situations. The BER reduction rate of the proposed RBF-OBF system is higher than 92% in additive white Gaussian noise channel and higher than 89% in line-of-sight multipath channel. [ABSTRACT FROM AUTHOR]

Positioning technology is an important component of environmental perception and the basis of decision-making and motion control for intelligent vehicles. Current independent positioning methods inevitably have defects and poor environmental adaptability. To improve positioning accuracy and stability using low-cost sensors, a multi-sensor fusion positioning strategy for intelligent vehicles using global pose graph optimization is proposed in this paper. This strategy complements the advantages of multiple sensors to obtain global optimal positioning results, and it can cope with a variety of challenging working conditions. Considering the fast response of the inertial measurement unit (IMU) and the advantages of a camera without drift, this strategy realizes the tightly coupled fusion of vision and the IMU to obtain the optimal pose of visual-inertial odometry (VIO) by nonlinear optimization. Moreover, this strategy refines the modeling of the IMU, and proposes a keyframe selection strategy to deal with driving in a straight line without obvious feature changes, turning, and other driving conditions. Taking into account the versatility of the global positioning system (GPS) and the low cost of the network real-time kinematic (NRTK) positioning, the output of VIO and GPS/NRTK is adaptively fused through global pose graph optimization to maintain global consistency. Finally, the multi-sensor fusion positioning strategy is verified using the KITTI dataset on the ROS simulation platform. The results show that the multi-sensor fusion positioning strategy for intelligent vehicles has better accuracy and environmental adaptability at a lower cost than state-of-the-art strategies. [ABSTRACT FROM AUTHOR]

The ongoing growth of Internet of Things (IoT) traffic increasesthe emergence of Multi-Access Edge Computing (MEC), which can serve IoT devices to process edge missions properly. The power supply for IoT devices is addressed by energy harvesting (EH) technology. However, the energy arrival model obeys the unknown energy arrival process. In addition, due to the dynamical changes of network state, it is crucial to study the access control in the MEC-based green IoT system. In this paper, we propose an MEC-based access control strategy to maximize the system utility for the green IoT system, considering the spectral efficiency and the successful access ratio from the perspective of operators and users respectively. Specifically, we model the access control problem as a Constrained Markov Decision Process (CMDP), and develop a novel centralized reward-based experience replay deep convolutional Q network algorithm (RCQN) to attain the optimal access control for EH IoT devices. Additionally, to enrich the prior knowledge of access control strategy, we design a Long Short-Term Memory (LSTM) based energy prediction module to predict the energy state of IoT devices by learning the historical energy arrival information, whose output is taken as the state information of RCQN. Simulation results demonstrate that the proposed LSTM-based RCQN access control algorithm significantly improves the system utility with a proper reward design and training mechanism. [ABSTRACT FROM AUTHOR]

This paper proposes a deep reinforcement learning-based video streaming scheme for mobility-aware vehicular networks, e.g., vehicles on the highway. We consider infrastructure-assisted and mmWave-based scenarios in which the macro base station (MBS) cannot directly provide the streaming service to vehicles due to the short range of mmWave beams so that small mmWave base stations (mBSs) along the road deliver the desired videos to users. Motivated by the fact that a video stream consists of sequential chunks and smooth streaming has to be provided while users pass through multiple mBSs at high speed, the MBS proactively pushes some video chunks of the desired contents to mBSs. This is done to support vehicles that are currently covered and/or will be by each mBS. We formulate the dynamic video delivery scheme that adaptively determines 1) which content, 2) what quality and 3) how many chunks to be proactively delivered from the MBS to mBSs using Markov decision process (MDP). Since it is difficult for the MBS to track all the channel conditions and the network states have extensive dimensions, we adopt the deep deterministic policy gradient (DDPG) algorithm for the DRL-based video delivery scheme. This paper finally shows that the DRL agentlearns a streaming policy that pursues high average quality while limiting packet drops, avoiding playback stalls, reducing quality fluctuations and saving backhaul usage. [ABSTRACT FROM AUTHOR]

The heterogeneous fog radio access networks (Fog-RAN), the integration of fog computing, and traditional heterogeneous radio access networks can be implemented through the next-generation wireless communication networks. However, most of the solutions are limited to the spectrum efficiency optimization, and cross-tier interference existing in the fog access points (F-APs) could affect the network performance seriously. In this paper, the user association, resource allocation (including bandwidth and power), and caching deployment are investigated in the heterogeneous Fog-RAN to consider energy efficiency and cross-tier interference mitigation. Specifically, the user association, resource allocation, and caching strategy are formulated as a non-convex optimization problem and then transformed into a convex problem, which can be solved by a proposed algorithm based on the concept of the alternating direction method of multipliers (ADMM). Then an ADMM-based algorithm is proposed to enhance the energy efficiency of the Fog-RAN. Compared with the current solutions, simulation results illustrate the proposed algorithm’s convergence and effectiveness. [ABSTRACT FROM AUTHOR]

In nonsaturated 802.11 distributed coordination function (DCF) networks, existing studies had observed a salient phenomenon: the maximum stable throughput may be far higher than the saturation throughput and last for a long duration (say, months). Such a maximum stable throughput is called the presaturation throughput peak. The long-duration peak suggests that 802.11 DCF networks may provide a far higher stable throughput than what we generally believe, without worrying about a sudden deterioration of quality of service (QoS). This paper is devoted to developing a general theoretical framework to predict the peak. In the framework, we define a backoff entropy to quantify the uncertainty of the inherent random backoff process of 802.11 DCF networks, and then innovatively introduce a BackoffEntropy-Peak linearity property (i.e., the peak is linearly proportional to the backoff entropy) for the peak prediction. This framework is applicable for a general configuration of contention windows (CWs). It enables us to reveal the most essential dependency of the peak on the initial CW size and the number of network nodes. Further, we design peak-based call admission control (CAC) schemes that can be performed quickly and easily, without requiring network performance measurements and complex calculations. We verify our framework and CAC schemes via widely adopted 802.11 DCF ns2 and ns3 simulators (mostly with typical 802.11 standard settings). Extensive simulations show that our framework and CAC schemes trade within 9% peak prediction errors for making 802.11 DCF networks provide high stable throughput with good QoS (such as short delay and low collision probability). This paper is the first to propose applying the information entropy to study the throughput-stability problem. We believe that this study makes a crucial breakthrough in thoroughly investigating nonsaturated performance and network stability of random access wireless networks. [ABSTRACT FROM AUTHOR]

Indoor drone or Unmanned Aerial Vehicle (UAV) operations, automated or with pilot control, are an upcoming and exciting subset of drone use cases. Automated indoor flights tighten the requirements of stability and localization accuracy in comparison with the classic outdoor use cases which rely primarily on (RTK) GNSS for localization. In this paper the effect of multiple sensors on 3D indoor position accuracy is investigated using the flexible sensor fusion platform OASE. This evaluation is based on real-life drone flights in an industrial lab with mm-accurate ground truth measurements provided by motion capture cameras, allowing the evaluation of the sensors based on their deviation from the ground truth in 2D and 3D. The sensors under consideration for this research are: IMU, sonar, SLAM camera, ArUco markers and Ultra-Wideband (UWB) positioning with up to 6 anchors. The paper demonstrates that using this setup, the achievable 2D (3D) indoor localization error varies between 4.4 cm and 21 cm (4.9 cm and 67.2 cm) depending on the selected set of sensors. Furthermore, cost/accuracy trade-offs are included to indicate the relative importance of different sensor combinations depending on the (engineering) budget and use case. These lab results were validated in a Proof of Concept deployment of an inventory scanning drone with more than 10 flight hours in a 65 000 m2 warehouse. By combining lab results and real-life deployment experiences, different subsets of sensors are presented as a minimal viable solution for three different indoor use cases considering accuracy and cost: a large drone with little weight- and cost restrictions, one or more medium sized drones, and a swarm of weight and cost restricted nano drones. [ABSTRACT FROM AUTHOR]

The critical nature of vehicular communications requires their extensive testing and evaluation. Analytical models can represent an attractive and cost-effective approach for such evaluation if they can adequately model all underlying effects that impact the performance of vehicular communications. Several analytical models have been proposed to date to model vehicular communications based on the IEEE 802.11p (or DSRC) standard. However, existing models normally model in detail the MAC (Medium Access Control), and generally simplify the propagation and interference effects. This reduces their value as an alternative to evaluate the performance of vehicular communications. This paper addresses this gap, and presents new analytical models that accurately model the performance of vehicle-to-vehicle communications based on the IEEE 802.11p standard. The models jointly account for a detailed modeling of the propagation and interference effects, as well as the impact of the hidden terminal problem. The model quantifies the PDR (Packet Delivery Ratio) as a function of the distance between transmitter and receiver. The paper also presents new analytical models to quantify the probability of the four different types of packet errors in IEEE 802.11p. In addition, the paper presents the first analytical model capable to accurately estimate the Channel Busy Ratio (CBR) metric even under high channel load levels. All the analytical models are validated by means of simulation for a wide range of parameters, including traffic densities, packet transmission frequencies, transmission power levels, data rates and packet sizes. An implementation of the models is provided openly to facilitate their use by the community. [ABSTRACT FROM AUTHOR]

Mobile edge computing has been an important supplement for traditional cloud computing architecture to offer low-delay computing services to mobile users. However, it is in general impossible for edge service providers to overdeploy so much edge resources to satisfy the rapidly increasing while diverse user demands. In this paper, we study a mobile edge computing system consisting of a service platform, cloudlets joining the system, and mobile users. In this study, we focus on a profit-driven perspective such that the service platform purchases computation resource from the resource-rich cloudlets and makes profit by processing tasks from user side. The design objective is to maximize the platform profit subject to budget constraint and stringent delay requirements for task processing. We formulate this problem as a mixed integer programming problem. Due to the NP-hardness of the problem, we design a logic based Benders decomposition algorithm as the offline solution. We further study the scenario where the task arrivals from user side and resource availability at the cloudlets are both stochastic and unknown in advance. We accordingly propose a Multi-Armed Bandit learning based resource purchasing and greedy task scheduling algorithm for the online scenario. Simulations results show the high performance of our proposed algorithms. [ABSTRACT FROM AUTHOR]

This paper considers the $\mathscr{L}_{2}$ string stability analysis and controller synthesis for vehicle platooning under jamming attacks and interferences from other communication channels. Jamming attacks and interferences for vehicle platooning systems are modeled as periodic denial of service attacks. Further, the vehicle platooning with denial of service attacks is modeled as a distributed switching system where an average dwell time approach is adopted for the stability analysis. Under the distributed switching system framework, this paper presents a co-design paradigm for the vehicle platooning. The distributed event-triggered method (ETM) and controllers are presented to guarantee $\mathscr{L}_{2}$ string stability, which can ensure that the output cannot be amplified along the vehicle platooning. Sufficient conditions for $\mathscr{L}_{2}$ string stability are then provided to guide the co-design of the ETM and controllers, which can be efficiently obtained by solving LMIs. Simulation results are presented to demonstrate the efficacy of the proposed co-design approach in addressing the denial of service attacks for vehicle platooning systems. [ABSTRACT FROM AUTHOR]

This paper proposes a path tracking controller to assist the electronic-four-wheel drive (e-4WD) vehicle in following the desired path profile. It utilizes only readily available in-vehicle sensors and a standalone global positioning system (GPS). Noteworthy, both the lateral distance error and the heading angle error between the desired path profile and the vehicle are calculated using only a standalone GPS. Therefore, the proposed algorithm can be easily applied to mass-produced e-4WD vehicles. A model predictive control (MPC) is selected as the controller type, which derives optimal control input considering both state and input constraints of in-wheel motor (IWM) in the e-4WD vehicle. Due to the advantage of this MPC predicting the vehicle's future dynamic behavior in advance, it is possible to output a more preemptive and stable yaw moment for vehicle path tracking. Finally, a weighted least square (WLS) allocation that is suitable for redundant actuator configuration is utilized to distribute the optimal IWM torques to the front left and right wheels of the e-4WD vehicle. The major contributions of the proposed control algorithm are as follows. 1) It is the first time in this paper that the MPC is applied to path tracking of e-4WD vehicles. 2) The condensed constraint matrix of the proposed MPC has a structure that can be easily applied to the linear programming. Using the CarSim simulation and the real-car based experiment, the effectiveness of the proposed MPC algorithm is verified by a comparative analysis. Thus, the high path tracking accuracy of the proposed algorithm is confirmed. [ABSTRACT FROM AUTHOR]

Lithium-ion batteries (LIBs) charging at low temperatures will easily accelerate the aging of LIBs and reduce the useful life. This paper applies advanced multi-factors coupling aging model and bi-objective particle swarm optimization (PSO) algorithm to derive suitable charging patterns for LIBs at low temperatures. Based on the results of orthogonal experiments, which consider the effects of charging rate, charging temperature and charging cut-off voltage on battery aging, the low-temperature capacity degradation model was established. Furthermore, two important yet competing charging objectives, including battery health and charging time, are taken into account simultaneously. These two conflicting charging objectives are traded off by solving a bi-objective optimization problem based on battery electrothermal and aging behavior. Combined with PSO algorithm, the optimal low-temperature charging strategy is obtained. As a result, the three-stage constant current and constant voltage (CC-CV) charging strategy is optimized to balance various combinations of charging objectives. Different tradeoffs are compared and analyzed based on the Pareto frontiers. The verification results show that the optimized three-stage CC-CV charging strategy can effectively offer feasible health-conscious charging with desirable tradeoffs among charging speed and battery health under low-temperature charging conditions. [ABSTRACT FROM AUTHOR]

Aiming at the low-frequency oscillation (LFO) phenomenon in high-speed railways, this paper proposes a feedback linearized virtual inertia control (VIC) strategy of the traction converter based on a sliding mode observer (SMO) to improve the robustness of the system and suppress the occurrence of LFO. First, to optimize the total harmonic distortion of the traction grid-side current, the inner loop controller is designed as the feedback linearization control. Then, the voltage outer loop is designed as a combination of the VIC designed in this paper and SMO, which enhances the system inertia and reduces the impact of external interference on the system, while reducing the controller's demand for electrical power on the DC-side. Furthermore, a small-signal model is established to analyze the stability of the single-phase vehicle-grid system under the proposed control. The influence of the control parameters on stability is discussed in detail. Finally, the comparison of software simulation and hardware-in-the-loop experimental results between traditional PI control, feedback linearization control, feedback+SMO, feedback+VIC and the proposed control method shows that the proposed control has better dynamic and static characteristics, and can effectively inhibit the occurrence of LFO. [ABSTRACT FROM AUTHOR]

Multiple signal classification (MUSIC) has been widely applied in multiple-input multiple-output (MIMO) receivers for direction-of-arrival (DOA) estimation. To reduce the cost of radio frequency (RF) chains at millimeter-wave bands, hybrid analog-digital structure has been adopted in massive MIMO transceivers. In this situation, received signals at the antennas are unavailable to the digital receiver, and as a consequence, the spatial covariance matrix (SCM), which is essential in MUSIC algorithm, cannot be obtained using traditional sample average approach. Based on our previous work, we propose a novel algorithm for SCM reconstruction in hybrid massive MIMO systems with multiple RF chains in this paper. By switching the analog beamformers to a group of predetermined DOAs, SCM can be reconstructed through the solutions of a set of linear equations. Furthermore, a low-complexity algorithm, as well as a careful selection of the predetermined DOAs, will be also presented in this paper. Simulation results show that the proposed algorithms can reconstruct the SCM accurately so that MUSIC algorithm can be well used in hybrid massive MIMO systems with multiple RF chains. [ABSTRACT FROM AUTHOR]