47 results on '"Lu, Ruochen"'
Search Results
2. Nanoscale imaging of super-high-frequency microelectromechanical resonators with femtometer sensitivity
- Author
-
Lee, Daehun, Jahanbani, Shahin, Kramer, Jack, Lu, Ruochen, and Lai, Keji
- Published
- 2023
- Full Text
- View/download PDF
3. Thin-Film Lithium Niobate Acoustic Resonator with High Q of 237 and k2 of 5.1% at 50.74 GHz
- Author
-
Kramer, Jack, Chulukhadze, Vakhtang, Huynh, Kenny, Barrera, Omar, Liao, Michael, Cho, Sinwoo, Matto, Lezli, Goorsky, Mark S., and Lu, Ruochen
- Subjects
Signal Processing (eess.SP) ,FOS: Electrical engineering, electronic engineering, information engineering ,Electrical Engineering and Systems Science - Signal Processing - Abstract
This work reports a 50.74 GHz lithium niobate (LiNbO3) acoustic resonator with a high quality factor (Q) of 237 and an electromechanical coupling (k2) of 5.17% resulting in a figure of merit (FoM, Q x k2) of 12.2. The LiNbO3 resonator employs a novel bilayer periodically poled piezoelectric film (P3F) 128 Y-cut LiNbO3 on amorphous silicon (a-Si) on sapphire stack to achieve low losses and high coupling at millimeter wave (mm-wave). The device also shows a Q of 159, k2 of 65.06%, and FoM of 103.4 for the 16.99 GHz tone. This result shows promising prospects of P3F LiNbO3 towards mm-wave front-end filters., 4 pages, 5 figures, published in 2023 Joint Conference of the IEEE International Frequency Control Symposium & European Frequency and Time Forum (IEEE IFCS 2023)
- Published
- 2023
4. A Frequency Independent Framework for Synthesis of Programmable Non-reciprocal Networks
- Author
-
Lu, Ruochen, Krol, Jack, Gao, Liuqing, and Gong, Songbin
- Published
- 2018
- Full Text
- View/download PDF
5. Thin-Film Lithium Niobate Acoustic Delay Line Oscillators
- Author
-
Li, Ming Huang, Lu, Ruochen, Manzaneque Garcia, T., Gong, Songbin, Cheung, Karen, and Horsley, David
- Subjects
Materials science ,Amplifier ,lithium niobate ,Lithium niobate ,dBc ,020206 networking & telecommunications ,02 engineering and technology ,piezoelectric transducers ,01 natural sciences ,phase noise ,Frequency comb ,chemistry.chemical_compound ,MEMS ,chemistry ,0103 physical sciences ,Negative feedback amplifier ,Phase noise ,oscillator ,0202 electrical engineering, electronic engineering, information engineering ,Insertion loss ,Center frequency ,Atomic physics ,010301 acoustics ,acoustic delay lines - Abstract
In this work, thin-film lithium niobate (LiNbO 3 ) acoustic delay line (ADL) based oscillators are experimentally investigated for the first time for the application of single-mode oscillators and frequency comb generation. The design space for the ADL-based oscillator is first analyzed, illustrating that the key to low phase noise lies in high center frequency ( $f_{o}$ ), large delay ( $\tau_{G}$ ), and low insertion loss (IL) of the delay. Therefore, two self-sustained oscillators employing low noise amplifiers (LNA) and a low IL, long delay ( $f_{o}=157\ \mathrm{MHz},\ \mathrm{IL} =2.9\ \mathrm{dB},\ \tau_{G}= 200-440\mathrm{ns}$ ) SH 0 mode ADLs are designed for a case study. The two SH 0 ADL oscillators show measured phase noise of −109 dBc/Hz and −127 dBc/Hz at 10-kHz offset while consuming 16 mA and 48 mA supply currents, respectively. Although the carrier power of the proposed oscillator is lower than published state-of-the-art ADL oscillators, competitive phase noise performance is still attained thanks to the low IL. Finally, frequency comb generation is also demonstrated with the same delay line and a commercial RF feedback amplifier, showing a comb spacing of 3.4 MHz that matches the open-loop characterization.
- Published
- 2020
6. Acoustic Loss of GHz Higher-Order Lamb Waves in Thin-Film Lithium Niobate: A Comparative Study.
- Author
-
Lu, Ruochen, Yang, Yansong, and Gong, Songbin
- Subjects
- *
LAMB waves , *SOUND-wave attenuation , *LITHIUM niobate , *DELAY lines , *QUALITY factor , *COMPARATIVE studies - Abstract
This work reports a comparative study of acoustic loss between different Lamb waves at GHz in thin-film lithium niobate (LiNbO3). The propagation loss (PL) of higher-order Lamb waves in thin-film LiNbO3 is studied for the first time using acoustic delay line (ADL) testbeds. The acoustic wave attenuation and quality factors ($Q$) of different Lamb waves are extracted, showing higher $Q\text{s}$ for higher-order Lamb modes than fundamental modes in air and vacuum at room temperature. The extracted $Q\text{s}$ are higher than those reported in thin-film LiNbO3 resonators, implying the electrode and anchor-induced loss as the dominant loss factors. The ADL-based loss analysis framework is readily extendable to acoustic damping study in other microwave acoustic platforms. [2021-0165] [ABSTRACT FROM AUTHOR]
- Published
- 2021
- Full Text
- View/download PDF
7. Visualization of acoustic power flow in suspended thin-film lithium niobate phononic devices.
- Author
-
Lee, Daehun, Meyer, Shawn, Gong, Songbin, Lu, Ruochen, and Lai, Keji
- Subjects
ELECTRICAL load ,PIEZOELECTRIC thin films ,LITHIUM niobate ,FAST Fourier transforms ,VISUALIZATION ,SOUND waves ,FLOW visualization ,OPTICAL diffraction - Abstract
We report direct visualization of gigahertz-frequency acoustic waves in lithium niobate phononic circuits. Primary propagation parameters, such as the power flow angle and propagation loss, are measured by transmission-mode microwave impedance microscopy. Using a fast Fourier transform, we can separately analyze forward and backward propagating waves and quantitatively evaluate the propagation loss. Our work provides insightful information on the propagation, diffraction, and attenuation in piezoelectric thin films, which is highly desirable for designing and optimizing phononic devices for microwave signal processing. [ABSTRACT FROM AUTHOR]
- Published
- 2021
- Full Text
- View/download PDF
8. RF acoustic microsystems based on suspended lithium niobate thin films: advances and outlook.
- Author
-
Lu, Ruochen and Gong, Songbin
- Subjects
- *
LITHIUM niobate , *THIN films , *ACOUSTIC wave propagation , *RADIO frequency , *PIEZOELECTRIC devices - Abstract
This paper presents a review of the radio frequency thin-film lithium niobate (LiNbO3) based acoustic microsystems. Thanks to their high electromechanical coupling (k 2), low loss, and great frequency scalability, thin-film LiNbO3 has outperformed state-of-the-art acoustic technologies in the past decade. This paper first reviews the acoustic wave transduction and propagation in thin-film LiNbO3 and then showcases the emerging acoustic applications. Outlook for further platform development and more functions is offered for future thin-film LiNbO3 based acoustic microsystems development. [ABSTRACT FROM AUTHOR]
- Published
- 2021
- Full Text
- View/download PDF
9. Stock Trend Prediction Algorithm Based on Deep Recurrent Neural Network.
- Author
-
Lu, Ruochen and Lu, Muchao
- Subjects
RECURRENT neural networks ,ARTIFICIAL neural networks ,LOGICAL prediction ,DEEP learning ,PROBLEM solving ,STOCK prices - Abstract
With the return of deep learning methods to the public eye, more and more scholars and industry researchers have tried to start exploring the possibility of neural networks to solve the problem, and some progress has been made. However, although neural networks have powerful function fitting ability, they are often criticized for their lack of explanatory power. Due to the large number of parameters and complex structure of neural network models, academics are unable to explain the predictive logic of most neural networks, test the significance of model parameters, and summarize the laws that humans can understand and use. Inspired by the technical analysis theory in the field of stock investment, this paper selects neural network models with different characteristics and extracts effective feature combinations from short-term stock price fluctuation data. In addition, on the basis of ensuring that the prediction effect of the model is not lower than that of the mainstream models, this paper uses the attention mechanism to further explore the predictive K -line patterns, which summarizes usable judgment experience for human researchers on the one hand and explains the prediction logic of the hybrid neural network on the other. Experiments show that the classification effect is better using this model, and the investor sentiment is obtained more accurately, and the accuracy rate can reach 85%, which lays the foundation for the establishment of the whole stock trend prediction model. In terms of explaining the prediction logic of the model, it is experimentally demonstrated that the K -line patterns mined using the attention mechanism have more significant predictive power than the general K -line patterns, and this result explains the prediction basis of the hybrid neural network. [ABSTRACT FROM AUTHOR]
- Published
- 2021
- Full Text
- View/download PDF
10. Acoustic Loss in Thin-Film Lithium Niobate: An Experimental Study.
- Author
-
Lu, Ruochen, Yang, Yansong, and Gong, Songbin
- Subjects
- *
DELAY lines , *QUALITY factor , *THIN films , *LITHIUM niobate , *CRYSTAL resonators , *MICROFABRICATION - Abstract
This work reports an experimental study of acoustic loss in thin-film lithium niobate (LiNbO3) using acoustic delay lines (ADLs). Unlike prior resonator-based quality factor (Q) studies, this approach directly extracts the damping in thin-film LiNbO3, avoiding the influence of other intricate loss mechanisms, e.g., anchor loss and electrode-induced loss. Acoustic attenuation of fundamental symmetric (S0) and shear horizontal (SH0) waves are studied in suspended LiNbO3 thin films of different thicknesses. The attenuation is significantly higher in thinner LiNbO3 films, suggesting the LiNbO3 crystal degradation during the microfabrication as the primary loss origin. Nevertheless, the extracted equivalent Q in thin-film LiNbO3 is still higher than reported values, suggesting that anchor design and electrode quality remain the bottlenecks for higher Q. The proposed loss extraction framework is readily extendable to other acoustic thin-film structures. [2021-0107] [ABSTRACT FROM AUTHOR]
- Published
- 2021
- Full Text
- View/download PDF
11. Near-Zero Drift and High Electromechanical Coupling Acoustic Resonators at > 3.5 GHz.
- Author
-
Hassanien, Ahmed E., Lu, Ruochen, and Gong, Songbin
- Subjects
- *
ACOUSTIC resonators , *ACOUSTIC couplers , *LAMB waves , *SOUND waves , *ACOUSTIC surface waves , *LITHIUM niobate - Abstract
In this article, near-zero drift and high electromechanical coupling acoustic resonators have been designed and demonstrated. The acoustic resonator is based on Lamb acoustic waves in a bimorph composed of lithium niobate on silicon dioxide. Our approach breaks through a performance boundary in conventional Lamb-wave resonators by introducing the bimorph while operating at higher order resonant modes. This enables the resonator to achieve frequency scalability, a low-temperature coefficient of frequency, and high electromechanical coupling altogether. The electromechanical coupling and temperature coefficient of the resonator were analytically optimized for the A3 mode through adjusting the thicknesses of different materials in the bimorph. Resonators with different dimensions and stack thickness were fabricated and measured, resulting in a temperature coefficient of frequency ranging from −17.6 to −1.1 ppm/°C, high electromechanical coupling ranging from 13.4% to 18%, and quality factors up to 800 at 3.5 GHz. The achieved specifications are adequate for fifth-generation (5G) sub-6-GHz frequency bands n77 and n78. [ABSTRACT FROM AUTHOR]
- Published
- 2021
- Full Text
- View/download PDF
12. Gigahertz Low-Loss and High Power Handling Acoustic Delay Lines Using Thin-Film Lithium-Niobate-on-Sapphire.
- Author
-
Lu, Ruochen, Yang, Yansong, Hassanien, Ahmed E., and Gong, Songbin
- Subjects
- *
DELAY lines , *ACOUSTIC surface waves , *GROUP velocity , *SAPPHIRES , *PHASE velocity , *LITHIUM niobate , *INSERTION loss (Telecommunication) - Abstract
In this work, we present the first group of gigahertz low-loss, wideband, and high power handling delay lines (ADLs) using a thin-film lithium niobate (LiNbO3)-on-sapphire platform. The ADLs leverage a single-phase unidirectional transducer (SPUDT) to efficiently excite the shear horizontal surface acoustic wave (SH-SAW) in the film stack. The fabricated miniature SH-SAW ADL at 1.1 GHz shows a low insertion loss (IL) of 2.8 dB, a wide fractional bandwidth (FBW) of 6.14%, and a fast phase velocity of 5127 m/s. The device also features a high 1-dB compression point (P1dB) of 30.4 dBm. The temperature coefficient of frequency is −45 ppm/K. ADLs with delays between 12 and 172 ns have been implemented, with IL between 2.8 and 8.3 dB. SH-SAW propagation characteristics are extracted, showing a group velocity of 4747 m/s and a propagation loss of 6.73 dB/mm or 31.9 dB/ $\mu \text{s}$. The simultaneous low-loss and high power handling illustrate the great potential of LiNbO3-on-sapphire for RF and cross domain applications at gigahertz. [ABSTRACT FROM AUTHOR]
- Published
- 2021
- Full Text
- View/download PDF
13. Lateral Spurious Mode Suppression in Lithium Niobate A1 Resonators.
- Author
-
Yang, Yansong, Gao, Liuqing, Lu, Ruochen, and Gong, Songbin
- Subjects
LITHIUM niobate ,LAMB waves ,RESONATORS ,QUALITY factor ,LITHIUM cell electrodes ,ELECTRICAL load ,MEMS resonators - Abstract
This work presents an improved design that exploits dispersion matching to suppress the spurious modes in the lithium niobate first-order antisymmetric (A1) Lamb wave mode resonators. The dispersion matching in this work is achieved by micro-machining the lithium niobate thin film to balance the electrical and mechanical loadings of electrodes. In this article, the dispersion matchings of the A1 mode in lithium niobate based on different metals are analytically modeled and validated with finite-element analysis. The fabricated devices exhibit spurious-free responses with a quality factor of 692 and an electromechanical coupling coefficient of 28%. The demonstrated method herein could overcome a significant hurdle that is currently impeding the commercialization of A1 devices. [ABSTRACT FROM AUTHOR]
- Published
- 2021
- Full Text
- View/download PDF
14. Low-Loss 5-GHz First-Order Antisymmetric Mode Acoustic Delay Lines in Thin-Film Lithium Niobate.
- Author
-
Lu, Ruochen, Yang, Yansong, Link, Steffen, and Gong, Songbin
- Subjects
- *
DELAY lines , *SOUND waves , *INSERTION loss (Telecommunication) , *LITHIUM niobate , *THIN films , *MICROELECTROMECHANICAL systems - Abstract
In this work, we present the low-loss acoustic delay lines (ADLs) at 5 GHz, using the first-order antisymmetric (A1) mode in 128° Y-cut lithium niobate thin films. The ADLs use a single-phase unidirectional transducer (SPUDT) design with a feature size of quarter acoustic wavelength. The design space is analytically explored and experimentally validated. The fabricated miniature A1 ADLs with a feature size of $0.45~\mu \text{m}$ show a high operating frequency at 5.4 GHz, a minimum insertion loss (IL) of 3 dB, a fractional bandwidth (FBW) of 1.6%, and a small footprint of 0.0074 mm2. The low IL and high operating frequency have significantly surpassed the state-of-the-art performance of ADLs. The propagation characteristics of A1 acoustic waves have also been extracted. The demonstrated designs can lead to low-loss and high-frequency transversal filters for future 5G applications in the sub-6-GHz bands. [ABSTRACT FROM AUTHOR]
- Published
- 2021
- Full Text
- View/download PDF
15. Low-Loss Unidirectional Acoustic Focusing Transducer in Thin-Film Lithium Niobate.
- Author
-
Lu, Ruochen, Yang, Yansong, and Gong, Songbin
- Subjects
- *
ACOUSTIC transducers , *DELAY lines , *INSERTION loss (Telecommunication) , *LITHIUM niobate , *MICROELECTROMECHANICAL systems , *ENHANCED magnetoresistance , *TRANSDUCERS - Abstract
In this work, we present gigahertz low-loss unidirectional acoustic focusing transducers in thin-film lithium niobate. The design follows the anisotropy of fundamental symmetric (S0) waves in X-cut lithium niobate. The implemented acoustic delay line testbed consisting of a pair of the proposed transducers shows a low insertion loss of 4.2 dB and a wide fractional bandwidth of 7.5% at 1 GHz. The extracted transducer loss is 1.46 dB, and the propagation loss of the S0 waves is 0.0126 dB/ $\mu \text{m}$. The design framework is readily extendable to other acoustic modes, given consideration on the optimal orientation for power flow and electromechanical transduction. [ABSTRACT FROM AUTHOR]
- Published
- 2020
- Full Text
- View/download PDF
16. 10–60-GHz Electromechanical Resonators Using Thin-Film Lithium Niobate.
- Author
-
Yang, Yansong, Lu, Ruochen, Gao, Liuqing, and Gong, Songbin
- Subjects
- *
MEMS resonators , *ELECTROMECHANICAL devices , *RESONATORS , *LAMB waves , *MICROELECTROMECHANICAL systems , *WIRELESS communications , *LITHIUM niobate , *LEAD zirconate titanate - Abstract
This work presents a new class of microelectromechanical system (MEMS) resonator toward 60 GHz for the fifth-generation (5G) wireless communications. The wide range of the operating frequencies is achieved by resorting to different orders of the antisymmetric Lamb wave modes in a 400-nm-thick Z-cut lithium niobate thin film. The resonance of 55 GHz demonstrated in this work marks the highest operating frequency for piezoelectric electromechanical devices. The fabricated device shows an extracted mechanical $Q$ of 340 and an $f\times Q$ product of $1.87\times 10^{13}$ in a footprint of $2 \times 10^{-3}$ mm2. The performance has shown the strong potential of LiNbO3 antisymmetric mode devices for front-end applications in 5G high-band. [ABSTRACT FROM AUTHOR]
- Published
- 2020
- Full Text
- View/download PDF
17. Enabling Higher Order Lamb Wave Acoustic Devices With Complementarily Oriented Piezoelectric Thin Films.
- Author
-
Lu, Ruochen, Yang, Yansong, Link, Steffen, and Gong, Songbin
- Subjects
- *
PIEZOELECTRIC thin films , *LAMB waves , *SOUND waves , *ACOUSTIC devices , *LITHIUM niobate - Abstract
In this work, we present a new paradigm for enabling gigahertz higher-order Lamb wave acoustic devices using complementarily oriented piezoelectric (COP) thin films. Acoustic characteristics are first theoretically explored with COP lithium niobate (LiNbO3) thin films, showing their excellent frequency scalability, low loss, and high electromechanical coupling ($k^{2}$). Acoustic resonators and delay lines are then designed and implemented, targeting efficient excitation of higher-order Lamb waves with record-breaking low loss. The fabricated resonator shows a $2^{\mathbf {nd}}$ -order symmetric (S2) resonance at 3.05 GHz with a high quality factor ($Q$) of 657, and a large $k^{2}$ of 21.5% and a $6^{\mathbf {th}}$ -order symmetric (S6) resonance at 9.05 GHz with a high $Q$ of 636 and a $k^{2}$ of 3.71%, both among the highest demonstrated for higher-order Lamb wave devices. The delay lines show an average insertion loss (IL) of 7.5 dB and the lowest reported propagation loss of 0.014 dB/ $\mu \text{m}$ at 4.4 GHz for S2. Notable acoustic passbands up to 15.1 GHz are identified. Upon further optimizations, the proposed COP platform can lead to gigahertz low-loss wideband acoustic components. [2020-0127] [ABSTRACT FROM AUTHOR]
- Published
- 2020
- Full Text
- View/download PDF
18. A Wideband Oscillator Exploiting Multiple Resonances in Lithium Niobate MEMS Resonator.
- Author
-
Kourani, Ali, Lu, Ruochen, and Gong, Songbin
- Subjects
- *
LITHIUM niobate , *PHASE noise , *VOLTAGE-controlled oscillators , *MEMS resonators , *RESONANCE , *QUALITY factor , *RADIO frequency - Abstract
This article presents a comprehensive guide to codesign lithium niobate (LiNbO3) lateral overtone bulk acoustic resonators (LOBARs) and voltage-controlled oscillators (VCOs) using discrete components on a printed circuit board (PCB). The analysis focuses on understanding the oscillator-level tradeoffs between the number of locked tones, frequency stability, tuning range, power consumption, and phase noise. Moreover, this article focuses on understanding the relationship between the abovementioned specifications and the different LOBAR parameters, such as electromechanical coupling (${k}_{t}^{{2}}$), quality factor (${Q}$), transducer design, and the resonator size. As a result of this study, the first voltage-controlled MEMS oscillator (VCMO) based on LiNbO3 LOBAR is demonstrated. Our LOBAR excites over 30 resonant modes in the range of 100–800 MHz with a frequency spacing of 20 MHz. The VCMO consists of an LOBAR in a closed loop with two amplification stages and a varactor-embedded tunable LC tank. By adjusting the bias voltage applied to the varactor, the tank can be tuned to change the closed-loop gain and phase responses of the oscillator so that the Barkhausen conditions are satisfied for a particular resonant mode. The tank is designed to allow the proposed VCMO to lock to any of the ten overtones ranging from 300 to 500 MHz. These ten tones are characterized by average ${Q}\text{s}$ of 2100, ${k}_{t}^{{2}}$ of 1.5%, figure of merit ($\text {FOM} = {Q} {k}_{t}^{{2}}$) of 31.5 enabling low phase noise, and low-power oscillators crucial for Internet of Things (IoT). Due to the high ${Q}\text{s}$ of the LiNbO3 LOBAR, the measured VCMO shows a close-in phase noise of −100 dBc/Hz at 1-kHz offset from a 300-MHz carrier and a noise floor of −153 dBc/Hz while consuming 9 mW. With further optimization, this VCMO can lead to direct radio frequency (RF) synthesis for ultralow-power transceivers in multimode IoT nodes. [ABSTRACT FROM AUTHOR]
- Published
- 2020
- Full Text
- View/download PDF
19. GHz Low-Loss Acoustic RF Couplers in Lithium Niobate Thin Film.
- Author
-
Lu, Ruochen, Yang, Yansong, Li, Ming-Huang, and Gong, Songbin
- Abstract
We present the first group of GHz low-loss acoustic radio frequency (RF) couplers using the fundamental symmetric (S0) mode in X-cut lithium niobate thin films. The demonstrated multistrip couplers (MSCs) significantly surpass the insertion loss (IL) and the operating frequency of the previous works in more compact structures, thanks to the large electromechanical coupling and low loss of S0 in lithium niobate. The design space of S0 MSCs is first explored. Devices with different coupling factors are fabricated using different numbers of strips. Based on the S0 testbed with an IL of 4.5 dB at 1 GHz, the hybrid coupler shows an IL of 7.5 dB, while the track changer shows an IL of 5.1 dB, over a 3-dB fractional bandwidth of 8%. Couplers at different frequencies (between 0.75 and 1.55 GHz) are also investigated. Upon further optimizations, the S0 MSC platform can potentially enable low-loss wideband signal processing functions toward an RF acoustic component kit. [ABSTRACT FROM AUTHOR]
- Published
- 2020
- Full Text
- View/download PDF
20. A Unidirectional Transducer Design for Scaling GHz AlN-Based RF Microsystems.
- Author
-
Lu, Ruochen, Link, Steffen, and Gong, Songbin
- Subjects
- *
ALUMINUM nitride , *TRANSDUCERS , *SIGNAL processing , *INSERTION loss (Telecommunication) , *DELAY lines , *RADIO frequency - Abstract
In this work, we present a novel unidirectional transducer design for frequency scaling aluminum nitride (AlN)-based radio frequency (RF) microsystems. The proposed thickness-field-excited single-phase unidirectional transducers (TFE-SPUDT) adopt 5/16 wavelength electrodes and, thus, enable efficient piezoelectric transduction with better frequency scalability. The design space of the TFE-SPUDT is theoretically explored and validated using the acoustic delay line (ADL) testbeds. The ADL testbeds with a large feature size of ${3}~\mu \text{m}$ show a center frequency of 1 GHz, a minimum insertion loss (IL) of 4.9 dB, and a fractional bandwidth (FBW) of 5.3%, significantly surpassing the IL and frequency scalability of the previously reported AlN transducers. The design approach can potentially contribute to various AlN-based RF microsystems for signal processing, physical sensing, optomechanical interaction, and quantum acoustic applications, and are readily extendable to other piezoelectric platforms. [ABSTRACT FROM AUTHOR]
- Published
- 2020
- Full Text
- View/download PDF
21. A1 Resonators in 128° Y-cut Lithium Niobate with Electromechanical Coupling of 46.4%.
- Author
-
Lu, Ruochen, Yang, Yansong, Link, Steffen, and Gong, Songbin
- Subjects
- *
RESONATORS , *QUALITY factor , *THIN films , *LITHIUM niobate , *MICROELECTROMECHANICAL systems , *PIEZOELECTRIC devices - Abstract
In this work, we present first-order antisymmetric (A1) mode resonators in 128° Y-cut lithium niobate (LiNbO3) thin films with electromechanical coupling coefficients ($k^{2}$) as large as 46.4%, exceeding the state-of-the-art. The achievable $k^{2}$ of A1 in LiNbO3 substrates of different orientations is first explored, showing X-axis direction in 128° Y-cut LiNbO3 among the optimal combinations. Subsequently, A1 resonators with spurious mode mitigation are designed and fabricated. In addition to the large $k^{2}$ , the implemented devices show a maximum quality factor ($Q$) of 598 at 3.2 GHz. Upon further optimization, the reported platform can potentially deliver a wideband acoustic-only filtering solution in 5G New Radio. [2020–0003] [ABSTRACT FROM AUTHOR]
- Published
- 2020
- Full Text
- View/download PDF
22. High Q Antisymmetric Mode Lithium Niobate MEMS Resonators With Spurious Mitigation.
- Author
-
Yang, Yansong, Lu, Ruochen, and Gong, Songbin
- Subjects
- *
MEMS resonators , *ACOUSTIC surface waves , *LAMB waves , *ACOUSTIC resonators , *LITHIUM niobate , *WIRELESS communications , *THIN films - Abstract
This paper reports on the demonstrations of first-order antisymmetric Lamb wave (A1) mode resonator as a new platform for front-end filtering of the fifth-generation (5G) wireless communication. The sub-6 GHz resonance in this work is achieved by employing the A1 mode in the micromachined Y-cut Lithium Niobate (LiNbO3) thin films. The spurious modes mitigation is achieved by optimizing the distribution of the electric field. The demonstrated figure-of-merit (FoM = Q ⋅ kt2) of 435 marks the first time that a new resonator technology with the FoMs exceeds those of surface acoustic wave (SAW) resonators and thin-film bulk acoustic resonators (FBARs) in the sub-6 GHz (1–6 GHz) frequency range. [2019-0241] [ABSTRACT FROM AUTHOR]
- Published
- 2020
- Full Text
- View/download PDF
23. GHz Broadband SH0 Mode Lithium Niobate Acoustic Delay Lines.
- Author
-
Lu, Ruochen, Yang, Yansong, Li, Ming-Huang, Manzaneque, Tomas, and Gong, Songbin
- Subjects
- *
DELAY lines , *INSERTION loss (Telecommunication) , *SIGNAL processing , *THIN films , *LITHIUM niobate , *MICROELECTROMECHANICAL systems - Abstract
We present the first group of GHz broadband SH0 mode acoustic delay lines (ADLs). The implemented ADLs adopt unidirectional transducer designs in a suspended X-cut lithium niobate thin film. The design space of the SH0 mode ADLs at GHz is first theoretically investigated, showing that the large coupling and sufficient spectral clearance to adjacent modes collectively enable the broadband performance of SH0 delay lines. The fabricated devices show 3-dB fractional bandwidth ranging from 4% to 34.3% insertion loss between 3.4 and 11.3 dB. Multiple delay lines have been demonstrated with center frequencies from 0.7 to 1.2 GHz, showing great frequency scalability. The propagation characteristics of SH0 in lithium niobate thin film are experimentally extracted. The demonstrated ADLs can potentially facilitate broadband signal processing applications. [ABSTRACT FROM AUTHOR]
- Published
- 2020
- Full Text
- View/download PDF
24. 5-GHz Antisymmetric Mode Acoustic Delay Lines in Lithium Niobate Thin Film.
- Author
-
Lu, Ruochen, Yang, Yansong, Li, Ming-Huang, Breen, Michael, and Gong, Songbin
- Subjects
- *
DELAY lines , *THIN films , *INSERTION loss (Telecommunication) , *FINITE element method , *PHASE velocity , *LITHIUM niobate - Abstract
We present the first group of acoustic delay lines (ADLs) at 5 GHz using the first-order antisymmetric (A1) mode in Z-cut lithium niobate thin films. The demonstrated ADLs significantly surpass the operation frequencies of the prior art with similar feature sizes because of their simultaneously fast phase velocity, large coupling coefficient, and low loss. In this article, the propagation characteristics of the A1 mode in lithium niobate are analytically modeled and validated with finite element analysis. The design space of A1 ADLs is then investigated, including both the fundamental design parameters and those introduced from the practical implementation. The implemented ADLs at 5 GHz show a minimum insertion loss of 7.9 dB, an average insertion loss (IL) of 9.1 dB, and a fractional bandwidth around 4%, with group delays ranging between 15 and 109 ns and the center frequencies between 4.5 and 5.25 GHz. The propagation characteristics of A1 mode acoustic waves have also been extracted for the first time. The A1 ADL platform can potentially enable wideband high-frequency passive signal processing functions for future 5G applications in the sub-6-GHz spectrum bands. [ABSTRACT FROM AUTHOR]
- Published
- 2020
- Full Text
- View/download PDF
25. Temperature Stability Analysis of Thin-Film Lithium Niobate SH0 Plate Wave Resonators.
- Author
-
Li, Ming-Huang, Chen, Chao-Yu, Lu, Ruochen, Yang, Yansong, Wu, Tao, and Gong, Songbin
- Subjects
LAMB waves ,RESONATORS ,MEMS resonators ,LITHIUM niobate ,FINITE element method ,MECHANICAL properties of condensed matter - Abstract
This work presents an extensive study on the temperature coefficient of frequency (TCF) for thin-film lithium niobate (LiNbO3) resonators. To capture the temperature-frequency behavior for each vibration mode, a one-dimensional (1D) multi-section TCF model is proposed and verified by both the finite-element method (FEM) and experiments. By partitioning the metallized and non-metallized sections of the interdigitated transducers (IDT) as distinct TCF blocks and properly considering the spatial energy distribution, the TCF of each mode can be accurately predicted. Two higher lateral-order resonators based on the fundamental shear-horizontal mode (SH0) are designed and fabricated on a LiNbO3-on-SiO2 wafer to provide odd- and even-order harmonics. TCFs of the first 6 overtones (from 84 to 515 MHz) are calculated using the material properties given in the literature, exhibiting a maximum TCF difference of 3 ppm/K between the theoretical prediction and measurement results. Although only SH0 resonators are selected for experimental verification, the proposed multi-section TCF model can be applied to other plate wave MEMS resonators. [2019-0112] [ABSTRACT FROM AUTHOR]
- Published
- 2019
- Full Text
- View/download PDF
26. MTT-S Technical Committee: RF MEMS and Microwave Acoustics Committee [MTT-S Society News].
- Author
-
Lu, Ruochen
- Abstract
Presents information on the MMTS RF MEMS and Microwave Acoustics Committee. [ABSTRACT FROM AUTHOR]
- Published
- 2022
- Full Text
- View/download PDF
27. Gigahertz Low-Loss and Wideband S0 Mode Lithium Niobate Acoustic Delay Lines.
- Author
-
Lu, Ruochen, Manzaneque, Tomas, Yang, Yansong, Li, Ming-Huang, and Gong, Songbin
- Subjects
- *
LITHIUM niobate , *DELAY lines - Abstract
We present the first group of gigahertz S0 mode low loss and wideband acoustic delay lines (ADLs). The ADLs use a single-phase unidirectional transducers (SPUDT) design to launch and propagate the S0 mode in an X-cut lithium niobate thin film with large electromechanical coupling and low damping. In this work, the theoretical performance bounds of S0 mode ADLs are first investigated, significantly surpassing those in state-of-the-art. The design tradeoffs of S0 mode ADLs, when scaled to the gigahertz frequency range, are also discussed. The fabricated miniature ADLs show a fractional bandwidth (FBW) of 4% and a minimum insertion loss (IL) of 3.2 dB, outperforming the incumbent surface acoustic wave (SAW) counterparts, and covering a wide range of delays from 20 to 900 ns for digitally addressable delay synthesis. Multiple ADLs with center frequencies from 0.9 to 2 GHz have been demonstrated, underscoring their great frequency scalability. The propagation properties of S0 waves in lithium niobate at the gigahertz range are experimentally extracted. The demonstrated ADLs can potentially enable wide-range and high-resolution delay synthesis that is highly sought after for the self-interference cancellation in full-duplex radios. [ABSTRACT FROM AUTHOR]
- Published
- 2019
- Full Text
- View/download PDF
28. Accurate Extraction of Large Electromechanical Coupling in Piezoelectric MEMS Resonators.
- Author
-
Lu, Ruochen, Li, Ming-Huang, Yang, Yansong, Manzaneque, Tomas, and Gong, Songbin
- Subjects
- *
MEMS resonators , *QUALITY factor , *MICROELECTROMECHANICAL systems , *CRYSTAL resonators , *LITHIUM niobate , *OPTOMECHANICS , *EXTRACTION techniques , *RESONATORS - Abstract
Recent advancements in the field of piezoelectric micro-resonators have produced devices, such as lithium niobate laterally vibrating resonators, with very high electromechanical coupling factors ($k_{t}^{2}$) and respectable quality factors (${Q}$). As a result, the records of the figure of merit (FoM) for radio-frequency MEMS resonators have been broken several times in the past five years. As exciting as these high FoMs are, they impose unique caveats in accurately extracting the electromechanical coupling often due to the presence of spurious modes. It is a less noted issue for micro-resonators with moderate ${k} _{t}^{2}$ , as spurious modes either are absent or do not significantly affect the common extraction technique based on identifying resonances and anti-resonances. This paper will first theoretically analyze how disregarding spurious modes can potentially lead to inaccurate extraction of ${k} _{t}^{2}$ of the intended mode and then offer a framework that accounts for spurious modes and accurately extracts electromechanical coupling using a multi-resonance recursive fitting. [2018-0209] [ABSTRACT FROM AUTHOR]
- Published
- 2019
- Full Text
- View/download PDF
29. Low-Loss and Wideband Acoustic Delay Lines.
- Author
-
Manzaneque, Tomas, Lu, Ruochen, Yang, Yansong, and Gong, Songbin
- Subjects
- *
ACOUSTIC delay lines , *THIN-film circuits , *BANDWIDTHS , *TRANSDUCERS , *FLUCTUATIONS (Physics) - Abstract
This paper demonstrates low-loss acoustic delay lines (ADLs) based on shear-horizontal waves in thin-film LiNbO3 for the first time. Due to its high electromechanical coupling, the shear-horizontal mode is suited for producing devices with large bandwidths. Here, we show that shear-horizontal waves in LiNbO3 thin films are also excellent for implementing low-loss ADLs based on unidirectional transducers. The high acoustic reflections and large transducer unidirectionality induced by the mechanical loading of the electrodes on a LiNbO3 thin film provide a great tradeoff between delay line insertion loss and bandwidth. The directionality for two different types of unidirectional transducers has been characterized. Delay lines with variations in the key design parameters have been designed, fabricated, and measured. One of our fabricated devices has shown a group delay of 75 ns with an IL below 2 dB over a 3-dB bandwidth of 16 MHz centered at 160 MHz (fractional bandwidth = 10%). The measured insertion loss for other devices with longer delays and different numbers of transducer cells are analyzed, and the loss contributing factors and their possible mitigation are discussed. [ABSTRACT FROM AUTHOR]
- Published
- 2019
- Full Text
- View/download PDF
30. A Radio Frequency Nonreciprocal Network Based on Switched Acoustic Delay Lines.
- Author
-
Lu, Ruochen, Manzaneque, Tomas, Yang, Yansong, Gao, Liuqing, Gao, Anming, and Gong, Songbin
- Subjects
- *
ACOUSTIC delay lines , *CIRCULATORS (Electrical engineering) , *DESIGN , *INSERTION loss (Telecommunication) , *LITHIUM niobate - Abstract
This paper demonstrates the first nonreciprocal network based on switched low-loss acoustic delay lines. The four-port circulator is built upon a recently reported frequency-independent, programmable, nonreciprocal framework based on switched delay lines. The design space for such a system, including the origins of the insertion loss (IL) and harmonic responses, is theoretically investigated, illustrating that the key to better performance and low-cost modulation signal synthesis lies in a large delay. To implement a large delay, we resort to in-house fabricated low-loss, wideband lithium niobate (LiNbO3)SH0 mode acoustic delay lines employing single-phase unidirectional transducers. The four-port circulator, consisting of two switch modules and one delay line module, has been modularly designed, assembled, and tested. The design process employs time-domain full circuit simulation, and the results match well with measurements. An 18.8-dB nonreciprocal contrast between IL (6.6 dB) and isolation (25.4 dB) has been achieved over a fractional bandwidth of 8.8% at a center frequency 155 MHz, using a record low switching frequency of 877.19 kHz. The circulator also shows 25.9-dB suppression for the intramodulated tone and 30 dBm for IIP3. Upon further development, such a system can potentially lead to future wideband, low-loss chip-scale nonreciprocal radio frequency systems with unprecedented programmability. [ABSTRACT FROM AUTHOR]
- Published
- 2019
- Full Text
- View/download PDF
31. Nanowatt-Level Wakeup Receiver Front Ends Using MEMS Resonators for Impedance Transformation.
- Author
-
Bassirian, Pouyan, Moody, Jesse, Roy, Abhishek, Scott Barker, N., Calhoun, Benton H., Bowers, Steven M., Lu, Ruochen, Gao, Anming, Manzaneque, Tomas, and Gong, Songbin
- Subjects
CMOS transceivers ,MICROELECTROMECHANICAL systems ,LITHIUM niobate ,ELECTRIC potential ,BANDWIDTHS - Abstract
This paper presents the first demonstration of nanowatt-level CMOS wakeup receiver (WuRx) front ends (FEs) that utilize microelectromechanical system (MEMS)-based matching networks (MNs). The first FE uses a fully MEMS-based MN (MMN) that operates at 88.8 MHz. It consists of a large array of lithium niobate resonators that are fabricated on the same die. Measurements of the integrated WuRx FE with the MMN indicate that its loaded voltage gain achieves a bandwidth of 0.78 MHz with a quality factor of 114. The second FE uses a hybrid MN (HMN) that operates at 457 MHz. It consists of an aluminum nitride laterally vibrating resonator as well as eight discrete inductors and capacitors surrounding the MEMS device. Measurements of the integrated WuRx FE with the HMN indicate that it achieves a sensitivity of −54 dBm with 7 nW of average dc power consumption without a digital correlator. [ABSTRACT FROM AUTHOR]
- Published
- 2019
- Full Text
- View/download PDF
32. RF Filters with Periodic Passbands for Sparse Fourier Transform-Based Spectrum Sensing.
- Author
-
Lu, Ruochen, Manzaneque, Tomas, Yang, Yansong, Zhou, Jin, Hassanieh, Haitham, and Gong, Songbin
- Subjects
- *
FOURIER transforms , *RESONATORS , *ACOUSTICS , *MICROELECTROMECHANICAL systems , *PIEZOELECTRICITY - Abstract
This paper demonstrates a passive low-insertion-loss (IL) RF filter with periodic passbands and capable of sparsifying the spectrum from 238 to 526 MHz for sparse Fourier transform (SFT)-based spectrum sensing. The demonstrated periodic filter employs LiNbO3 lateral overtone bulk acoustic resonators (LOBARs) with high-quality factors (Qs), large electromechanical coupling ($k_{t}^{2}$), and multiple equally spaced resonances in a ladder topology. To demonstrate the periodic filter, the LOBARs is first modeled to predict $k_{t}^{2}$ of various tones accurately. The fabricated LOBARs show $k_{t}^{2}$ larger than 1.5% and figure of merits ($Q\cdot k_{t}^{2}$) more than 30 for over 10 tones simultaneously, which agree with our modeled response, and are both among the highest demonstrated in overmoded resonators. The multi-band filter centered at 370 MHz has then been obtained with a passband span of 291 MHz, a spectral spacing of 22 MHz, an IL of 2 dB, FBWs around 0.6%, and a sparsification ratio between 7 and 15. An out-of-band rejection around 25 dB has also been achieved for more than 14 bands. The great performance demonstrated by the RF filter with 14 useable periodic passbands will serve to enable future SFT-based spectrum sensing. [2018-0155] [ABSTRACT FROM AUTHOR]
- Published
- 2018
- Full Text
- View/download PDF
33. A Piezoelectric Micromachined Ultrasonic Transducer Using Thin-Film Lithium Niobate.
- Author
-
Lu, Ruochen, Breen, Michael, Hassanien, Ahmed E., Yang, Yansong, and Gong, Songbin
- Subjects
- *
THIN films , *ULTRASONIC transducers , *LITHIUM niobate , *QUALITY factor , *PIEZOELECTRIC transducers , *TRANSDUCERS , *VACUUM - Abstract
This letter presents the first piezoelectric micromachined ultrasonic transducer (PMUT) based on thin-film lithium niobate (LiNbO3). The figures of merit (FoMs) of LiNbO3 as ultrasound sensors and transducers are first studied, showing great prospective as a balanced transceiver platform. Efficient flexural mode excitation is achieved using a proposed lateral-field-excitation (LFE) structure. The implemented device shows a flexural mode at 7.6 MHz, with a high electromechanical coupling ($k^{2}$) of 4.2%. Measured quality factor ($Q$) in vacuum is 2605, indicating the low structural loss, while measured $Q$ in air is 264, suggesting the ultrasound radiation. A dynamic displacement sensitivity of 20.2 nm/V is measured. Upon further optimizations, LiNbO3-based PMUTs are promising candidates for miniature ultrasound applications. [2020-0287] [ABSTRACT FROM AUTHOR]
- Published
- 2020
- Full Text
- View/download PDF
34. Low Phase Noise RF Oscillators Based on Thin-Film Lithium Niobate Acoustic Delay Lines.
- Author
-
Li, Ming-Huang, Lu, Ruochen, Manzaneque, Tomas, and Gong, Songbin
- Subjects
- *
PHASE noise , *LITHIUM niobate , *DELAY lines , *ACOUSTIC surface waves , *LAMB waves , *NONLINEAR oscillators - Abstract
An RF oscillator has been demonstrated using a wideband SH0 mode lithium niobate acoustic delay line (ADL). The design space of the ADL-based oscillators is theoretically investigated using the classical linear time-invariant (LTI) phase noise model. The analysis reveals that the key to low phase noise is low insertion loss (IL), large delay (τG), and high carrier frequency (ƒo). Two SH0 ADL oscillators based on a single SH0 ADL (fo = 157 MHz, IL = 3.2 dB, ƒG = 270 ns) but with different loop amplifiers have been measured, showing low phase noise of −114 dBc/Hz and −127 dBc/Hz at 10-kHz offset with a carrier power level of −8 dBm and 0.5 dBm, respectively. These oscillators not only have surpassed other Lamb wave delay oscillators but also compete favorably with surface acoustic wave (SAW) delay line oscillators in performance. [2019-0223] [ABSTRACT FROM AUTHOR]
- Published
- 2020
- Full Text
- View/download PDF
35. Lithium Niobate Phononic Crystals for Tailoring Performance of RF Laterally Vibrating Devices.
- Author
-
Lu, Ruochen, Manzaneque, Tomas, Yang, Yansong, and Gong, Songbin
- Subjects
- *
LITHIUM niobate crystallography , *PHONONIC crystals , *BAND gaps , *RADIO frequency , *VIBRATION (Mechanics) - Abstract
This paper reports the first demonstration of phononic crystals (PnCs) in suspended lithium niobate thin films, which exhibit band gaps for tailoring the performance of laterally vibrating devices. Transmission and reflection properties of lithium niobate PnCs for both shear-horizontal (SH0) and length-extensional (S0) modes have been investigated and subsequently explored in two applications. In the first case, PnC-embedded delay lines were designed for filtering with stopbands, while in the second case, PnC-bounded resonators were implemented for spurious mode suppression. Equivalent circuit models incorporating acoustic scattering parameters of the designed PnCs and Mason’s model of the transducers have been built for each application. Benchmarked to reference devices without PnCs, the measured PnCs embedded in delay lines show 20-dB attenuation in the stopbands and less than 2-dB loss in the passbands for the SH0 mode, and 30-dB attenuation in the stopbands and less than 10-dB loss in the passbands for the S0 mode. The fabricated piezoelectric PnC-bounded resonator has shown a quality factor of 434 at 142.7 MHz with undesired spurious modes significantly suppressed. These demonstrations show that lithium niobate PnCs for laterally vibrating devices can potentially lead to wideband and low-loss acoustic functions for radio frequency signal processing. [ABSTRACT FROM AUTHOR]
- Published
- 2018
- Full Text
- View/download PDF
36. Lithium Niobate MEMS Chirp Compressors for Near Zero Power Wake-Up Radios.
- Author
-
Manzaneque, Tomas, Lu, Ruochen, Yang, Yansong, and Gong, Songbin
- Subjects
- *
RADIO frequency , *TRANSDUCERS , *ELECTRONICS , *BANDWIDTHS , *SIGNAL processing - Abstract
This paper presents the first demonstration of chirp compressors based on laterally vibrating modes in suspended lithium niobate thin films. Both shear-horizontal and length-extensional modes have been explored and demonstrated with the electromechanical coupling coefficients of 30% and 39%, respectively, in a double-dispersive delay line structure. The high electromechanical coupling, along with the low propagation loss in the suspended thin film, produces a low insertion loss of 10 dB over a large fractional bandwidth of 50%. The best fabricated device demonstrates a delay-bandwidth product of 100, and provides a voltage gain of 5 to the corresponding chirp signals. Moreover, significant signal-to-noise ratio enhancements (>100), collectively enabled by the processing gain and filtering characteristics of the chirp compressors, have been demonstrated. The measured devices, in this paper, greatly outperform state-of-the-art chirp compressors based on surface acoustic waves in insertion loss for a comparable TB. As a result, signal-to-noise ratio enhancement and voltage gain have been simultaneously demonstrated for the first time in a passive device and the analog domain. The high performance can be harnessed to greatly enhance the sensitivity of near zero power wake-up radio receivers and enable low-power wireless connectivity for Internet of Things applications. [2017–0126] [ABSTRACT FROM PUBLISHER]
- Published
- 2017
- Full Text
- View/download PDF
37. Deciphering intermodulation in AlN laterally vibrating resonators.
- Author
-
Lu, Ruochen, Gao, Anming, and Gong, Songbin
- Published
- 2016
- Full Text
- View/download PDF
38. 4.5 GHz Lithium Niobate MEMS Filters With 10% Fractional Bandwidth for 5G Front-Ends.
- Author
-
Yang, Yansong, Lu, Ruochen, Gao, Liuqing, and Gong, Songbin
- Subjects
- *
SUBSTRATE integrated waveguides , *LITHIUM niobate , *FILTERS & filtration , *BANDWIDTHS - Abstract
This paper presents a new class of micro-electro-mechanical system (MEMS) C-band filters for 5G front-ends. The filter is comprised of resonators based on the first-order asymmetric Lamb wave (A1) mode in thin-film lithium niobate. Two filters have been demonstrated at 4.5 GHz with sharp roll-off, flat in-band group delay, and spurious-free response over a wide frequency range. The first design shows a 3-dB fractional bandwidth (FBW) of 10%, an insertion loss (IL) of 1.7 dB, an out-of-band (OoB) rejection of −13 dB, and a compact footprint of 0.36 mm2, while the second design shows a 3-dB FBW of 8.5%, an IL of 2.7 dB, an OoB rejection of −25 dB, and a footprint of 0.9 mm2. The demonstrations herein mark the largest FBW achieved for acoustic-only filters at 5G frequencies. [2019-0083] [ABSTRACT FROM AUTHOR]
- Published
- 2019
- Full Text
- View/download PDF
39. Aluminum Nitride Lamb Wave Delay Lines With Sub-6 dB Insertion Loss.
- Author
-
Lu, Ruochen, Link, Steffen, Zhang, Shibin, Breen, Michael, and Gong, Songbin
- Subjects
- *
ALUMINUM nitride , *DELAY lines , *INSERTION loss (Telecommunication) , *LAMB waves , *EWES - Abstract
We present a group of low-loss Lamb mode acoustic delay lines in an aluminum nitride (AlN) thin film. The low-loss acoustic delay lines are enabled by the thickness-field-excited single-phase unidirectional transducers. The fabricated miniature acoustic delay lines show a fractional bandwidth of 4.5%, a minimum insertion loss of 5.9 dB, outperforming the previously reported aluminum nitride delay platforms. The demonstrated delay ranges from 105 ns to 165 ns with center frequencies from 175 MHz to 255 MHz. The design approach and the significantly lower insertion loss described herein are expected to open new horizons for hybridized signal processing based on AlN and CMOS. [2019-0094] [ABSTRACT FROM AUTHOR]
- Published
- 2019
- Full Text
- View/download PDF
40. Study of thermal nonlinearity in lithium niobate-based MEMS resonators.
- Author
-
Lu, Ruochen and Gong, Songbin
- Published
- 2015
- Full Text
- View/download PDF
41. Analysis and Removal of Spurious Response in SH0 Lithium Niobate MEMS Resonators.
- Author
-
Song, Yong-Ha, Lu, Ruochen, and Gong, Songbin
- Subjects
- *
RESONATORS , *LITHIUM niobate , *MICROELECTROMECHANICAL systems , *ELECTRODES , *QUALITY factor - Abstract
This paper reports on the analysis and removal of transverse spurious modes in shear horizontal (SH0) mode lithium niobate (LiNbO3) laterally vibrating resonators (LVRs). A length-controlled electrode configuration that employs an optimized overlapping length between the adjacent electrodes has been developed to subdue the spurious modes. The technique modifies the stress and electric field distribution in the resonator body, consequently enabling near zero electromechanical coupling ( kt^{2} ) for the higher order transverse spurious modes. The length-controlled electrode configuration also reduces the loss at the interface between the metal electrodes and the piezoelectric layer, demonstrating a more than 2\times enhancement in quality factors {Q} . The fabricated LiNbO3 LVR with the length-controlled electrode configuration has shown an unprecedented spectral range (100–200 MHz) of spurious-free response, a high \mathit {k}_{t}^{2}$ value of 20.1%, a {Q} value of 1150, and, thereby, a remarkably high figure of merit of 230. [ABSTRACT FROM AUTHOR]
- Published
- 2016
- Full Text
- View/download PDF
42. A Laterally Vibrating Lithium Niobate MEMS Resonator Array Operating at 500 °C in Air.
- Author
-
Eisner, Savannah R., Chapin, Cailin A., Lu, Ruochen, Yang, Yansong, Gong, Songbin, and Senesky, Debbie G.
- Subjects
MEMS resonators ,LITHIUM niobate ,QUALITY factor ,ACOUSTIC couplers ,PIEZOELECTRIC materials ,CRYSTAL resonators - Abstract
This paper reports the high-temperature characteristics of a laterally vibrating piezoelectric lithium niobate (LiNbO
3 ; LN) MEMS resonator array up to 500 °C in air. After a high-temperature burn-in treatment, device quality factor (Q) was enhanced to 508 and the resonance shifted to a lower frequency and remained stable up to 500 °C. During subsequent in situ high-temperature testing, the resonant frequencies of two coupled shear horizontal (SH0) modes in the array were 87.36 MHz and 87.21 MHz at 25 °C and 84.56 MHz and 84.39 MHz at 500 °C, correspondingly, representing a −3% shift in frequency over the temperature range. Upon cooling to room temperature, the resonant frequency returned to 87.36 MHz, demonstrating the recoverability of device performance. The first- and second-order temperature coefficient of frequency (TCF) were found to be −95.27 ppm/°C and 57.5 ppb/°C2 for resonant mode A, and −95.43 ppm/°C and 55.8 ppb/°C2 for resonant mode B, respectively. The temperature-dependent quality factor and electromechanical coupling coefficient (kt 2 ) were extracted and are reported. Device Q decreased to 334 and total kt 2 increased to 12.40% after high-temperature exposure. This work supports the use of piezoelectric LN as a material platform for harsh environment radio-frequency (RF) resonant sensors (e.g., temperature and infrared) incorporated with high coupling acoustic readout. [ABSTRACT FROM AUTHOR]- Published
- 2021
- Full Text
- View/download PDF
43. A non-resonant, gravity-induced micro triboelectric harvester to collect kinetic energy from low-frequency jiggling movements of human limbs.
- Author
-
Lu, Yingxian, Wang, Xiaohong, Wu, Xiaoming, Qin, Jin, and Lu, Ruochen
- Subjects
MICROELECTROMECHANICAL systems ,ENERGY conversion ,TRIBOELECTRICITY ,ELECTROSTATIC induction ,HUMAN locomotion ,EXTREMITIES (Anatomy) - Abstract
This paper presents a non-resonant, gravity-induced micro triboelectric harvester with high internal resistance. The device collects kinetic energy from low-frequency jiggling movements for the power supply of portable electric devices such as wristwatches. It includes a friction module to produce triboelectric charge and an electrostatic induction module to export energy. The friction that transfers charge is induced by jiggling movements, with gravity and inertia of an internal slider, instead of with external direct force. The non-resonant structure allows the device to respond to low frequencies of 1.5–5.5 Hz, covering the frequencies of human motion. Load resistance sweeping shows that the optimal load resistance is about 1.1 GΩ, with the peak output voltage of about 260 V, and the output power of 60 µW. The proposed harvester responds to low-frequency kinetic energy in jiggling movements matching that of a human limb's running motion; so it has potential to convert the mechanical energy of arm swings or strides into electric energy. [ABSTRACT FROM AUTHOR]
- Published
- 2014
- Full Text
- View/download PDF
44. Near Spurious-Free Thickness Shear Mode Lithium Niobate Resonator for Piezoelectric Power Conversion.
- Author
-
Nguyen K, Chulukhadze V, Stolt E, Braun W, Segovia-Fernandez J, Chakraborty S, Rivas J, and Lu R
- Abstract
Piezoelectric power converters, where acoustic resonators replace the inductors as energy storage elements, promise much higher power density and higher efficiency compared to conventional circuits. Recently, lithium niobate (LiNbO3) piezoelectric resonators have been integrated within power converter circuits, showing good conversion efficiency, thanks to their high quality factor ( Q ) and electromechanical coupling ( k
t 2 ). However, the converter output power range is limited by large spurious modes near resonance. This work reports a near-spurious-free LiNbO3 thickness shear (TS) resonator, demonstrating a high Q of 3500 and kt 2 of 45% at 5.94 MHz, with a fractional suppressed region of 35%. First, we identify the best LiNbO3 crystal orientation for efficient TS resonators. Then, we propose a novel acoustic design without busbars for spurious suppression, which is extensively simulated, fabricated, and characterized. Further analysis is done to identify existing spurious modes in our proposed design, specifically the effect of dicing on our TS resonator design. Upon optimization, LiNbO3 TS resonators could potentially empower a new design space for low-loss and compact power converters.- Published
- 2023
- Full Text
- View/download PDF
45. A Laterally Vibrating Lithium Niobate MEMS Resonator Array Operating at 500 °C in Air.
- Author
-
Eisner SR, Chapin CA, Lu R, Yang Y, Gong S, and Senesky DG
- Abstract
This paper reports the high-temperature characteristics of a laterally vibrating piezoelectric lithium niobate (LiNbO
3 ; LN) MEMS resonator array up to 500 °C in air. After a high-temperature burn-in treatment, device quality factor ( Q ) was enhanced to 508 and the resonance shifted to a lower frequency and remained stable up to 500 °C. During subsequent in situ high-temperature testing, the resonant frequencies of two coupled shear horizontal (SH0) modes in the array were 87.36 MHz and 87.21 MHz at 25 °C and 84.56 MHz and 84.39 MHz at 500 °C, correspondingly, representing a -3% shift in frequency over the temperature range. Upon cooling to room temperature, the resonant frequency returned to 87.36 MHz, demonstrating the recoverability of device performance. The first- and second-order temperature coefficient of frequency (TCF) were found to be -95.27 ppm/°C and 57.5 ppb/°C2 for resonant mode A, and -95.43 ppm/°C and 55.8 ppb/°C2 for resonant mode B, respectively. The temperature-dependent quality factor and electromechanical coupling coefficient ( kt 2 ) were extracted and are reported. Device Q decreased to 334 and total kt 2 increased to 12.40% after high-temperature exposure. This work supports the use of piezoelectric LN as a material platform for harsh environment radio-frequency (RF) resonant sensors (e.g., temperature and infrared) incorporated with high coupling acoustic readout.- Published
- 2020
- Full Text
- View/download PDF
46. Using Functionalized Graphene Oxide as Carrier for Immobilization of Glutaryl-7-Aminocephalosporanic Acid Acylase.
- Author
-
Tan Q, Qiu J, Luo X, Chen Y, Liu Y, Wei H, Lu R, and Wu D
- Subjects
- Enzyme Stability, Enzymes, Immobilized, Graphite, Hydrogen-Ion Concentration, Kinetics, Temperature, Amidohydrolases metabolism, Cephalosporins
- Abstract
Graphene oxide has been widely used in biological applications because of good biocompatibility. In the present work, graphene oxide was synthesized successfully and was employed to immobilize glutaryl-7-aminocephalosporanic acid acylase (GLA). The immobilization conditions like pH, temperature, immobilization time, and enzyme/carrier ratio were investigated. Under the optimal immobilization conditions, the immobilization yield and efficiency were 86% and 52%, respectively. The characterization of the immobilized GLA was performed and compared with the free enzyme. The results indicated that the stability of the immobilized GLA was 1.7-folds than that of the free enzyme, and the kinetic parameters were also calculated. All these results show the potential industrial applications of the immobilized GLA in the production of 7-aminocephalosporinal acid (7-ACA).
- Published
- 2019
- Full Text
- View/download PDF
47. Study of cross-resistance mediated by antibiotics, chlorhexidine and Rhizoma coptidis in Staphylococcus aureus.
- Author
-
Wu D, Lu R, Chen Y, Qiu J, Deng C, and Tan Q
- Subjects
- Coptis chinensis, Microbial Sensitivity Tests, Anti-Bacterial Agents pharmacology, Chlorhexidine pharmacology, Drug Resistance, Multiple, Bacterial, Drugs, Chinese Herbal pharmacology, Staphylococcus aureus drug effects
- Abstract
This study aimed to determine whether selection by antibiotics, chlorhexidine (CHX) and Rhizoma coptidis extract (RCE) would lead to cross-resistance or decreased susceptibility in Staphylococcus aureus. The S. aureus reference strain ATCC 25923 as well as 14 clinical isolates were exposed to antibiotics, CHX and RCE at sublethal doses for up to 14 days. Changes in susceptibility were determined by analysis of minimum inhibitory concentrations (MICs). All isolates were cross-resistant to more than one other antibiotic following tetracycline exposure, and increased resistance (≥4-fold MIC increase) to RCE and CHX was observed in six and three isolates, respectively. Following selection by CHX, most of the treated strains showed no significant change in sensitivity to CHX. However, all strains developed cross-resistance to at least one antibiotic, and decreased susceptibility (≥4-fold MIC increase) to RCE appeared in seven strains. Following exposure to RCE, 11 isolates showed cross-resistance to at least one antibiotic. In addition, three RCE-exposed strains showed reduced susceptibility to CHX (4- or 8-fold MIC increase). The results obtained in this study imply that antibiotics, biocides and antimicrobial Chinese herbs might employ some of the same mechanisms of action against bacteria, triggering mutual cross-resistance to further foster the development of bacterial resistance., (Copyright © 2016 International Society for Chemotherapy of Infection and Cancer. Published by Elsevier Ltd. All rights reserved.)
- Published
- 2016
- Full Text
- View/download PDF
Catalog
Discovery Service for Jio Institute Digital Library
For full access to our library's resources, please sign in.