Search

This paper presents the digital implementation of a boundary controller with unipolar switching characteristic for single-phase voltage source full-bridge inverters. This paper expands the application of a second-order switching surface-based control method to unipolar switching of single-phase voltage source inverters (VSIs) using a finite-state machine. The finite-state machine has been formulated considering four different states of the inverter; positive,zero1, negative, andzero2. The second-order boundary control governs the current state of the system and provides proper switching action to keep the system within the desired reference. The control law is implemented digitally in F28m35x digital control card. A full-bridge inverter topology is used to achieve the three-level voltage switching. Various simulations and experiments were performed in a 550 VA, 120 V, 60 Hz VSI with a digitally implemented controller to verify the theoretical predictions. A high-quality voltage output was obtained for various loading conditions. The transient performance of the controller was investigated using a reference and load changes. A comparison of the implementation was made with the existing classical controllers to verify the fast-dynamic response of the system. [ABSTRACT FROM AUTHOR]

This paper proposes a new high-efficiency photovoltaic (PV) converter for grid connection through a high-leg delta transformer. The converter is composed of a symmetrically connected boost converter and three half-bridge inverters. One of the three half-bridge inverters is connected to the boost converter, and the others are directly connected to the PV terminals. As a result, this circuit configuration enables to reduce the power losses in both boost converter and inverters. This paper also proposes a new cooperative control method between the symmetrically connected boost converter and inverter. The control method can reduce the average switching frequency to 75% of that in a conventional one, resulting in a great reduction in the switching power loss. Experimental results confirm that the proposed circuit configuration makes it possible to improve its European efficiency from 91.6% to 94.5%. Moreover, system performance is evaluated on the assumption of maximum power point tracking operation. [ABSTRACT FROM AUTHOR]

This paper proposes generation of a 15-level (14 concentric) dodecagonal voltage space vector structure (DVSVS) for a star connected induction motor drive. The proposed multilevel DVSVS is obtained by cascading two inverters, namely a primary and secondary inverter. The primary inverter is a five-level (5L) structure formed by stacking two three-level flying capacitors with individual reduced dc sources and the secondary inverter is also a 5L structure formed by cascading two capacitor-fed cascaded H-bridges (CHB). The active power is supplied by the primary inverter, while the secondary inverter acts as switched capacitor harmonics filter, and capacitors in the secondary inverter are balanced naturally irrespective of load power factor for entire modulation index. The high-voltage dc supply fed primary inverter is operated in quasi-square wave mode, while the high frequency switching is applied to low voltage CHBs, thus, reducing the overall switching loss. The proposed scheme gives the advantages of both DVSVS and multilevel structure, thus, making it one of the solutions for battery or stacked dc-fed applications. The paper also presents the experimental results as well as comparison study with the existing topologies to support the advantages of proposed scheme. [ABSTRACT FROM AUTHOR]

To support the development of high-frequency ac microgrids in terms of compact design, high-voltage gain and low total harmonic distortion (THD), a buck–boost dual-leg-integrated step-up inverter is proposed in this paper. The inverter is formed by integrating a buck–boost converter into a conventional single-phase full-bridge inverter by sharing the upper switch and the body diode of the lower switch in both bridge-legs. Consequently, the component count is significantly reduced over the step-up inverter counterparts. In addition, to address the drawbacks of hybrid modulation methods adopted by existing dual-leg-integrated inverters, such as double-variable control, and high THD of output voltage/current at high input voltage and heavy load conditions, unipolar frequency doubling sinusoidal pulse width modulation scheme is adopted in this inverter. As a result, the modulation ratio M becomes the only control variable to regulate the output voltage/current and the control is simplified. The THD of the proposed inverter output can remain low throughout the entire input voltage range and load power range. This paper presents the topology derivation procedure, operation principle, and steady-state characteristics of the proposed inverter. To validate the effectiveness of theory, experimental results of a 400 W hardware prototype, where the output voltage frequency is at 500 Hz, are reported. [ABSTRACT FROM PUBLISHER]

This paper analyzes the combination in a cascaded H-bridge multilevel inverter (CHBI) based on transformers with the different turn ratios for increasing the voltage level and proposes the switching method for achieving the output voltage distribution among H-bridge cells (HBCs). The transformers used in this paper are connected to the output of the respective HBCs, and the secondary sides of all the transformers are connected in series for generating the final output voltage. Only one of the transformers, in particular, has a different turn ratio for increasing the output voltage level. In this paper, the possible turn ratio of the special transformer with a different turn ratio is discussed in detail, and a switching method based on the level-shifted switching method for the topology used in this paper is proposed. To verify the effectiveness of the proposed method, a three-phase 21-level CHBI is experimentally tested. [ABSTRACT FROM PUBLISHER]

In this paper, direct torque control (DTC) of five-phase induction motor (FPIM) is implemented using three-level neutral point clamped (TL-NPC) inverter. One of the advantages of three-level inverter over two-level one for DTC operation is the low torque ripple. Also TL-NPC inverter through space vector modulation technique gives low $ dv/dt$ transition with better voltage waveform. By applying conventional lookup table for DTC, the TL-NPC inverter does not ensures lower $dv/dt$ transition. In this paper, a novel switching scheme for DTC of FPIM using TL-NPC inverter is proposed that ensures the low $ dv/dt$ transition and balancing of dc-link capacitor voltages of TL-NPC inverter. To form the lookup table for DTC operation, instead of using voltage vectors directly, virtual vectors (VVs) are utilized. Two switching states are used in one sample time to generate a VV in $\alpha \beta$ plane, which gives zero resultant voltage in $ xy$ plane. The switching strategy ensures low number of transitions to reduce the switching losses. The switching state redundancies are used in a novel way to balance the dc-link capacitor voltages without using any additional hardware. The proposed technique to balance the dc-link capacitor voltage gives lower switching frequency. The MATLAB/Simulink environment is used for the simulation and the results are validated through experiments. [ABSTRACT FROM AUTHOR]

This paper proposes and validates model predictive control as an alternative control strategy for H-bridgeneutral-point-clamped (H-NPC) converters for single-phase grid-tied string photovoltaic (PV) systems. The presented control scheme achieves good quality current waveforms with unity power factor, dc-link voltage control, and neutral-point voltage minimization. Furthermore, the predictive controller has been further enhanced by including an average device switching frequency restriction and a $dv/dt$ mitigation. The main contribution of this paper is the avoidance of the potential leakage current due to parasitic capacitance of the PV modules by using a predictive model based control technique instead of modulated schemes and eliminating high-frequency common-mode voltage components. Experimental results during steady state and dynamic operation are presented to illustrate the behavior of the H-NPC converter commanded by the proposed control scheme. [ABSTRACT FROM AUTHOR]

This paper proposes an effective sliding mode controller (SMC) for a grid-connected 7-level packed U-cell (PUC7) inverter. The aim is to design a simple controller that deals effectively with the complex control problem of the PUC7 inverter (multiobjective control problem). The selection of the control actions is achieved according to the system state error at every sampling time, regardless of the previous values, which makes the control technique model-independent. The control algorithm evaluates online two cost functions (one for each state error), which are derived on the basis of sliding mode theory, and it selects the optimal control input in order to satisfy the reaching conditions of the two cost functions. Compared with the existing solutions, the proposed SMC technique ensures lower average switching frequency by tuning the hysteresis bandwidth of the capacitor-voltage error. The fast implementation, needless of gains tuning, and simple design procedure are the main features of the proposed algorithm. Simulation and experimental results are presented to prove the effectiveness of the proposed technique in controlling the PUC7 inverter with high dynamic performance and robustness against disturbances and parameters mismatch. [ABSTRACT FROM AUTHOR]

Recent technical advances in control, protection and interconnection of distributed power generation units imply that it is practically viable and economically profitable to keep them as backup generators in isolated operating modes. Therefore, along with the development of islanding detection techniques, seamless operation in transition between islanded and grid connected modes is required and more sophisticated control strategies are needed to recognize the existing working condition and adjust the performance to meet the strict standards of grid interconnection. This paper presents a new adaptive control structure, based on internal model control (IMC), which uses multiple models and an inherent islanding detection method through an optimized switching mechanism to tune the operation of a three-phase inverter under transitions between islanded and grid-tied conditions. By applying a power synchronization method, the system emulates the operation of a synchronous machine which is needless to rely on a phase-locked loop to synchronize during the transitions. Hardware co-simulation environment in Simulink/PLECS and Xilinx System Generator have been utilized to evaluate the transient behavior of the controller in discretized domain and verify its robustness during parameter variations and load switching conditions. Various switching rules have been applied and a comparison of their effect in transient response is demonstrated. The results, taken from several case studies, confirm the significant robustness of the proposed control methodology. [ABSTRACT FROM AUTHOR]

Reliability of power systems can be improved by the use of voltage source inverters (VSIs) with fast dynamic control, which can handle uncertainties induced by renewable energy resources and nonlinear loads. To ensure fast-dynamic response and simplified controller design, various model predictive control (MPC) methods are investigated in this paper. In the conventional MPC design for three-level VSIs, the cost function requires an additional term to ensure the balance of the neutral-point voltage (NP-V), which however can considerably impact the main goal of the MPC. To address this issue, an enhanced MPC using virtual space vectors is proposed, which allows the use of a significantly reduced weighting factor for the term in the cost function for NP-V balancing, while retaining fast-dynamic response. Additionally, the proposed MPC leads to reduced harmonic distortion in the VSI output voltage and current. Both simulation and controller hardware-in-the-loop studies are performed to demonstrate the effectiveness of the proposed enhanced MPC in an operating microgrid under both steady-state and fast-transient conditions. [ABSTRACT FROM AUTHOR]

Three-level inverter has an outstanding performance and is more advantageous in the switching vector selection than two-level inverter. In particular, the neutral-point voltage unbalance and common-mode voltage (CMV) reduction of three-level inverter should be carefully regulated for the appropriate operation, both of which, however, are mutually coupled resulting that the conventional space vector modulation (SVM) scheme cannot deal with them properly. To overcome this limitation, this paper proposes an improved space vector modulation (ISVM) technique to reduce the CMV and neutral-point voltage imbalance simultaneously. The generating mechanism of neutral-point voltage oscillation is derived. Based on the analysis, the proposed ISVM method adopts four voltage vectors (large, medium, small, and zero vectors) with adjusted dwell times to eliminate the ac unbalance of the neutral-point voltage. Considering the occurrence of neutral-point voltage disturbances, the dc neutral-point unbalance voltage is controlled by selecting the P-type or N-type small vector and adjusting the dwell times of small vectors for neutral-point voltage recovery. In addition, a novel switching sequence arrangement method with the minimal number of switches transition in one switching cycles and between switching cycles is proposed to reduce the total switching loss. Theoretical analysis and verification results show that the proposed ISVM scheme can reduce the magnitude of CMV to half of value using the conventional SVM, and an accurate control of ac and dc unbalanced neutral-point voltage can be obtained. [ABSTRACT FROM AUTHOR]

In this paper, a new space vector pulse width modulation method to extend the linear modulation range of a cascaded five level inverter topology with a single dc supply is presented. Using this method, the inverter can be controlled linearly and the peak phase fundamental output voltage of the inverter can be increased from 0.577 to 0.637 V\text{dc} without increasing the dc bus voltage and without exceeding the induction motor voltage rating. This new technique makes use of cascaded inverter pole voltage redundancy and property of the space vector structure for its operation. Using this, the induction motor drive can be operated till the full speed range (0–50 Hz) with the elimination of lower order harmonics in the phase voltage and phase current. The five-level topology presented in this paper is realized by cascading a two-level inverter and two full bridge modules with floating capacitors. The inverter topology and its operation for extending the modulation range is analyzed extensively. Simulation and experimental results for both steady-state and dynamic operating conditions are presented in this paper. [ABSTRACT FROM AUTHOR]

Zero-common-mode-voltage (CMV) operation of multilevel inverters results in reduced dc-bus utilization and reduced linear modulation range. In this paper, a method to increase the linear modulation range for zero-CMV operation without increasing the dc-bus voltage using a cascaded multilevel inverter with a single dc supply is presented. Using this method, the peak fundamental output voltage can be increased from 0.499 to 0.637  \textV\text{dc} with zero CMV inside the linear modulation range. Also, various pulse width modulation (PWM) switching sequences are analyzed in this paper, and the PWM sequence that gives minimum current ripple is used for the zero-CMV operation of the inverter. The inverter topology with single dc supply is realized by cascading a two-level inverter with two floating-capacitor-fed full-bridge modules. Simulation and experimental results for steady-state and dynamic operating conditions are presented to validate the proposed method. [ABSTRACT FROM AUTHOR]

This paper presents a model predictive control technique applied to a dual-active bridge inverter where one of the bridges is floating. The proposed floating bridge topology eliminates the need for isolation transformer in a dual inverter system and therefore reduces the size, weight, and losses in the system. To achieve multilevel output voltage waveforms, the floating inverter dc-link capacitor is charged to the half of the main dc-link voltage. A finite-set model predictive control technique is used to control the load current of the converter as well as the floating capacitor voltage. Model predictive control does not require any switching sequence design or complex switching time calculations as used for space vector modulation; thus, the technique has some advantages in this application. A detailed analysis of the converter as well as the predictive control strategy is given in this paper. Simulation and experimental results to validate the approach are also presented. [ABSTRACT FROM PUBLISHER]

This paper presents a three-phase open-end winding induction motor drive. The drive consists of a three-phase induction machine with open stator phase windings and dual-bridge inverter supplied from a single dc voltage source. To achieve multilevel output voltage waveforms, a floating capacitor bank is used for the second of the dual bridges. The capacitor voltage is regulated using redundant switching states at half of the main dc-link voltage. This particular voltage ratio (2:1) is used to create a multilevel output voltage waveform with three levels. A modified modulation scheme is used to improve the waveform quality of this dual inverter. This paper also compares the losses in the dual-inverter system in contrast with a single-sided three-level neutral point clamped converter. Finally, detailed simulation and experimental results are presented for the motor drive operating as an open-loop v /f controlled motor drive and as a closed-loop field-oriented motor controller. [ABSTRACT FROM PUBLISHER]

This paper presents a novel model predictive control (MPC) for the T-type single-phase three-level inverters. The cumbersome procedure in tuning of weighting factors is eliminated so that the implementation of the proposed MPC becomes easy. The constant switching frequency is achieved during the control implementation in order to facilitate the filter design. In order to optimize the distribution of the output current harmonics, multiple voltage vectors are employed in each control cycle with their application times setting inversely proportion to the respective cost function. The redundant small voltage vectors are utilized to balance the neutral point voltage of the inverter by directly regulating the upper and lower dc-link capacitors voltages. Finally, the proposed MPC algorithm is experimentally evaluated and compared with other two unfixed switching frequency MPC algorithms in terms of the steady state, transient performance, and parameter sensitivity. [ABSTRACT FROM AUTHOR]

This paper introduces a new configuration of bidirectional multilevel converter in electric vehicle (EV) applications. It has multilevel dc–dc converter with a dc link capacitor voltage balance feature. The multilevel dc–dc converter operates in a bidirectional manner, which is a fundamental requirement in EVs. Compared to the conventional configurations, the proposed one only implements two extra power switches and a capacitor to balance the voltage of the T-type multilevel inverter (MLI) capacitor over a complete drive cycle or at fault conditions. Therefore, no extra isolated sensor, control loops, and/or special switching pattern are required. Moreover, the proposed configuration due to the high-frequency cycle-by-cycle voltage balance between ${C_N}$ and ${C_P}$ , the bulky electrolytic capacitors used in T-type MLI, are replaced with more reliable longer life film capacitors. This will result in a size and weight reduction of the converter by 20%. This allows more real estate for the EV battery in the chassis’ space envelope to increase its capacity. The proposed configuration is tested and validated using a matlab/Simulink simulation model. A laboratory prototype of 1 kW is built to provide the proof of concept results as well. [ABSTRACT FROM AUTHOR]

The new IEEE 1547-2018 standard includes dynamic Volt/VAr control for photovoltaic (PV) smart inverters. While recent research has addressed the problem of optimal inverter dispatch, the interaction between inverters and the classical Volt/VAr control (VVC) regulation system needs further study. This paper proposes an approach that builds on the classical VVC solution with PVs, by computing for each inverter a rule that modulates the smart inverter reactive power in function of its real power. Two approaches are presented for computing the inverter's reactive power equation slope: the first approach is based on the robust minimization of the absolute voltage magnitude deviation via a linear program, whereas the second approach yields closed-form solutions inspired from distributionally robust chance constraints. Numerical results are presented on weakly meshed distribution networks having up to 3146 nodes; they demonstrate that the voltage violations due to intermittent real power variations are significantly reduced by the decision rules as compared to maintaining the last computed VVC set-points, even when the inverters operate at constant power factor or with default Volt/VAr settings proposed in the literature; additionally, the reactive power decision rules maintain a network loss level that is close to the average from a centralized solution. [ABSTRACT FROM AUTHOR]

This paper proposes a switching strategy for the Z-source inverter (ZSI), which has unequal short-through intervals to reduce the current ripple in the inductor of its impedance source. A size reduction of the inductor of the ZSI is one of the important issues in improving the power density of the ZSI, and the inductor current ripple reduction is required to achieve it. The proposed method can reduce the inductor current ripple by 27.8% compared with the conventional method that has equal short-through intervals without increasing the number of inverter switching. The proposed operation and ripple reduction were confirmed in experiments with a 3-kW-class laboratory prototype. Its result agreed to the calculated results, and it was confirmed that there is no increase in circuit losses caused by the application of the proposed method. [ABSTRACT FROM AUTHOR]

To reduce the common-mode voltage (CMV) and eliminate the CMV spikes for two-level voltage source inverters (2L-VSIs), an improved model predictive control (MPC) based CMV reduction method is proposed in this paper considering dead-time effects. First, an improved voltage vector (VV) preselection strategy is proposed to reduce the CMV spikes caused by the dead time. Second, a new hybrid VV preselection strategy based on a delay compensation strategy and a modified current sector division strategy is proposed to completely eliminate the CMV spikes. As the proposed hybrid VV preselection based MPC strategy makes full use of the six nonzero VVs of the 2L-VSI, the current total harmonic distortions and ripples are reduced. The simulation and experiments are carried out to verify the effectiveness of the proposed strategy. [ABSTRACT FROM AUTHOR]

In this paper, a fixed switching frequency model predictive current controller is designed and implemented on a sensorless five-level packed U-cell (PUC5) inverter interfacing the utility. The predictive control methodology is based on a voltage vector generation technique for the cost function optimization by nullifying its derivative. The aim of the controller is to allow a fixed-frequency operation with no iterations while operating as a utility line current regulator. A pulsewidth modulator based on employing PUC5 redundant switching states fixes the PUC5 auxiliary dc bus capacitor voltage to its desired level with no necessity of a regulator; the overall technique reduces system complexity with less sensors and no loops in the predictive algorithm making it suitable for industrial applications. System discrete model is developed and experimental results verify the performance of the designed controller in making a fast response in regulating the grid current and balancing the capacitor voltage. [ABSTRACT FROM AUTHOR]

Recently, a few fault-tolerant control strategies have been proposed for T-type three-level inverters to improve the reliability of the inverter system. However, the neutral-point (NP) voltage oscillations suppression is never considered in the previous fault-tolerant control strategies. In order to suppress the NP voltage oscillations when open-circuit fault occurs to NP switches, this paper proposes two novel fault-tolerant control strategies named as improved two-level switching tolerant control and hybrid switching tolerant control (HS-TC). Both methods are implemented by adding an optimal time-offset to the three-phase turn-ontimes. The corresponding time-offset value of each method is simply calculated considering the phase current and dwell time of [O] state. Moreover, an NP voltage balancing algorithm to eliminate the dc deviation and a dc bias to further reduce the NP voltage oscillations are used in the HS-TC. The performance and comparison of the tolerant controls with respect to the NP voltage oscillations, current total harmonic distortion, and dynamic response are illustrated and analyzed through the simulation and experimental results. [ABSTRACT FROM AUTHOR]

An isolated single sourced multi-output dc/dc converter with a high-frequency link was proposed before to feed different cells of the Asymmetrical Cascaded H-bridge (ACHB) inverter. One of the fundamental advantages of the ACHB is that the main H-bridge is commutated with fundamental frequency, passing the majority of the inverter power. However, the isolated dc/dc converter needs to be connected to the main voltage source with high-voltage/high-frequency switches, which limits the power capability and the efficiency of the converter. In this paper, a switching pattern based on nearest level modulation method is proposed to command all the power to be transferred through the main H-bridge. Therefore, the power circulates between the auxiliary H-bridges with no need for high-voltage switches. As a result, a single-input single-output auxiliary converter is needed with only 5% of the power rating. This solution reduces cost and size while it improves the efficiency of the converter. Furthermore, the architecture makes the inverter more suitable for high power and high-voltage applications. The inverter switching strategy is based on programmable firing angles. The main dc-link of the grid connected inverter is controlled to achieve maximum power point tracking, while the dc/dc isolated converter is controlled to regulate the auxiliary dc-links. The proposed topology is verified by simulation and experimental results using a 1.5 kW hardware prototype. [ABSTRACT FROM AUTHOR]

A 1-φ hybrid nine-level inverter (H9LI) topology has been proposed in this paper. The proposed H9LI topology uses a simple phase disposition pulsewidth modulation strategy to generate nine-voltage levels in the output. The main advantage of this topology is that it has a low switch count (ten switches) compared to the existing nine-level inverter topologies. To regulate the voltage across auxiliary capacitor, two innovative control techniques are proposed, which are integrated with the inverter modulation technique itself. Hence, it does not require any extra voltage balancing circuits to maintain the voltage across the auxiliary capacitor and input dc capacitors. A major advantage of these control techniques is that they eliminate the sensing of the coupled inductor current. Another significant advantage of H9LI is that loss distribution among all the power switches is more uniform compared to existing nine-level inverters. Due to low part count and absence of extra voltage balancing circuits, the H9LI achieves higher efficiency (η ≍ 94.5%) and lower cost. Furthermore, the requirement of filter size reduces due to the presence of coupled inductor in H9LI. The proposed 1-φ grid connected H9LI is verified through MATLAB/Simulink simulations and validated through experiments on a laboratory prototype of 400-VA rating. [ABSTRACT FROM AUTHOR]

In this paper, capacitor current sensorless control by using an observer is applied in a seamless transfer single-phase inverter. The proposed control system is a multiloop control system. The control loop is composed of a capacitor voltage outer control loop and capacitor current inner control loop for stand-alone mode. For on-grid mode, the grid current outer loop controller is combined with the stand-alone control structure to form a simple controller structure for mode switching. The capacitor current feedback signal is calculated using the observer in the discrete-time domain and thus sensors are not required. Use of the proposed observer for the inverter with capacitor current control has many advantages, such as sensorless capacitor current calculation, one-sample-ahead data prediction for sampling delay compensation, and an average capacitor current without ripple components. Verification of the theoretical analysis is presented through simulation and experiment. A 5-kW single-phase inverter prototype combined with a Li-ion battery is set up with a digital controller using a TI TMS320F28377D microcontroller unit to confirm the feasibility of the system. [ABSTRACT FROM AUTHOR]

In this paper, a novel space-vector pulsewidth modulation technique for a five-level active neutral-point clamped (5L-ANPC) inverter is proposed to eliminate the common-mode voltage (CMV). For the 5L-ANPC inverter, which produces a good output voltage performance and lowdv/dt, the total 125 voltage vectors can be generated, among which the proposed scheme employs only 19 voltage vectors producing a zero CMV. Due to the limitation of voltage vectors selected, the dc-link capacitor voltages of the 5L-ANPC inverter cannot be balanced by themselves. Therefore, the capacitor voltages of the inverter should be controlled by choosing the redundant switching states appropriately. The validity of the proposed modulation scheme has been verified by simulation and experimental results. [ABSTRACT FROM AUTHOR]

This paper proposes a control method for a five-level hybrid flying-capacitor (5L-HFC) inverter, of which structure stems from the conventional five-level active neutral-point-clamped (5L-ANPC) topology by dividing the dc-link stage into three series-connected capacitors. In this inverter, the voltage stress on the power switches connected to the dc link is reduced by a half compared with that of the 5L-ANPC topology, thus the lower number of equally voltage-rated power devices can be employed. Also, the power losses in the 5L-HFC inverter are more evenly distributed than in the 5L-ANPC. In order to balance the dc-link capacitor voltages, a third-order harmonic offset injection is applied. When a diode rectifier is used to supply the dc bus voltage, the balancing method is not effective if the modulation index is higher than 0.64. Thus, an auxiliary circuit is needed to support the balancing of the dc-link capacitor voltages. However, the unbalancing problem can be overcome in a full-range operation without the auxiliary circuit if the back-to-back configuration is utilized. Finally, simulation and experiment results have verified the performance of the 5L-HFC inverter with the proposed control method. [ABSTRACT FROM AUTHOR]

This paper proposes the new clamping angle control (CAC) pulse width modulation (PWM) method to restore its maximum linear modulation range of voltage source inverters (VSIs) reduced by the duty ratio limitation in hardware implementation, which makes the VSIs to operate nonlinearly in the high modulation range. The deadtime and the bootstrap gate driver circuit mainly cause this duty ratio limitation in practice. In particular, the bootstrap gate driver circuit is used in many industrial applications by avoiding the additional power supply to apply the gate-source voltage of power switches, and therefore making the VSIs to be small size with the low cost. First, the proposed CACPWM method is theoretically analyzed. Then, it is applied in the high modulation range to overcome the limitation of the duty ratio due to the use of the bootstrap gate driver circuit. Thereafter, its practical effectiveness is verified by both simulation and experimental tests. Also, the resulting harmonic distortions are compared with those by the conventional PWM methods. [ABSTRACT FROM AUTHOR]

An adaptive control of DPWM implementable in clamped-three-level inverters with two strings of photovoltaic (PV) panels in cascaded connection is proposed in this paper. The proposed modulation is developed based on the so-called circuit-level decoupling concept. It is able to provide balance line voltage even under unbalanced dc links. The unequal dc voltages appeared due to asymmetric maximum point of power trackings (MPPTs) are controlled by proper injection of zero-sequence voltage to the common mode voltage, while the total dc voltage is regulated based on the voltage commands generated by the MPPT of each string. Thus, both PV strings are able to be operated based on their MPPTs while there is almost no low-order harmonic distortion at the inverter output current. Compared with the previous methods, the high capability of the proposed method is evaluated by simulation study and experimental tests. [ABSTRACT FROM AUTHOR]

In this paper, a three-level quasi-switched boost T-type inverter (3L qSBT2I) is proposed. A new pulse-width modulated (PWM) control method is presented to reduce the inductor current ripple of the qSBT2 I. In the introduced PWM technique, the shoot-through duty cycle is maintained constant to keep the modulation index as high as possible. Then, the only control parameters of the qSBT2I are the duty cycles of the two additional switches. By controlling the duty cycles of the two additional switches, the voltage gain of the proposed qSBT2 I can be improved to a value larger than that of the conventional 3L impedance source inverters. The steady-state analysis, operating principles, and comparisons with the impedance source-based 3L inverters are presented. A 1-kW prototype is constructed to verify the operating principle of the 3L qSBT2I. An indirect dc-link voltage regulator and a capacitor voltage-balance controller are applied to the proposed qSBT2I. Simulation and experimental results are presented. [ABSTRACT FROM AUTHOR]

This paper investigates a multilevel inverter composed of series/parallel-connected H-bridges. The presented structure can be used for applications in which the use of semiconductor switches with low-voltage and low-current ratings is intended. A comprehensive system model, an overall control strategy to adjust the output voltage with constant magnitude and frequency, and a level-shifted PWM (LS-PWM) strategy based on a voltage vectors unidimensional analysis and a plane analysis are presented. The LS-PWM is capable of mitigating the low-frequency circulating current, thus generating multilevel voltage signals with low harmonic distortion, maximum number of levels, and low dv/dt. In addition, considering a wide range of values of voltages and currents and various power levels, the total converter losses are reduced compared with the conventional multilevel converters. Two multilevel conventional inverters with the same number of semiconductor switches are used for comparison. Simulation and experimental results demonstrate the feasibility of the studied converter. [ABSTRACT FROM AUTHOR]

An optimal current control strategy for asymmetrical hybrid multilevel inverters (MLIs) is proposed in this paper enabling their use on motor drives, static synchronous compensators, and photovoltaic and wind generators, where a fast and precise current regulation is required. A key feature of these highly efficient converters is that an ac machine (motor or transformer) operates according to an open-end winding configuration, connected on one side to a main MLI and, on the other side, to an auxiliary two-level inverter (TLI). The first efficiently controls the main power stream operating at a low switching frequency, while the TLI acts as an active power filter, exploiting a conventional high-frequency two-level pulsewidth modulation (PWM) technique. The proposed control scheme optimally exploits the key features of the two inverters by suitably sharing the control task. In fact, a predictive current control is assigned to the MLI, which can be accomplished by low switching frequency operations, while the high switching frequency of the PWM-operated TLI is exploited to accomplish a fast and precise closed-loop current control, processing only a part of the power stream flowing through the system, thus producing low power losses. Simulations and experimental results confirm the consistency of the proposed approach. [ABSTRACT FROM AUTHOR]

Microinverters operating into the single-phase grid from new energy source with low-voltage output face the challenges of efficiency bottleneck and twice-line-frequency variation. This paper proposed a multilevel inverter based on bridge modular switched-capacitor (BMSC) circuits with its superiority in conversion efficiency and power density. The topology is composed of dc–dc and dc–ac stages with independent control for each stage, aiming to improve system stability and simplify the control method. The BMSC dc–dc stage, which can be expanded to synthesize more levels, not only features multilevel voltage gain but also partially replaces the original bulk input capacitor and functions as an active energy buffer to enhance power-decoupling ability between dc and ac sides. In dc–ac stage, the control strategy of optimized unipolar frequency doubling sine-wave pulse width modulation is proposed to improve the quality of output waveform. Meanwhile, the multilevel voltage phase has been optimized to further reduce the power loss. Finally, a prototype has been built and tested. Associated with the simulation, the experimental results validate the practicability of these analyses. [ABSTRACT FROM PUBLISHER]

Three-phase three-leg inverter is one of the most popular topologies for inverters. When short-circuit fault occurs, the inverter is generally switched to the current-controlled mode from voltage-controlled mode to limit the fault currents. In this situation, the inverter becomes equivalent to a symmetric, three-phase, positive sequence current source. However, the voltage limiting may occur under asymmetrical fault. In this paper, a closed-loop model based on time-domain is originally developed as a means to investigate the fault current characteristics under asymmetrical fault. Based on the proposed model, a more intuitive insight into fault currents is presented as follows. 1) The positive sequence fundamental component of three-phase currents can still track the symmetric current references. 2) The magnitude of fault phase currents (ignoring the harmonics) will vary between 1 and $\sqrt 3 $ times of magnitude of current limiting references. Based on the conclusion, although the magnitudes of fault phase currents can be reduced by adopting smaller current limiting references, the actual magnitudes of fault phase currents will still vary in a range depending on the load impendence of healthy phase. Therefore, the reliable action of the protection devices is greatly affected and the selective protection cannot be realized. Furthermore, in order to achieve completely controllable fault currents under asymmetrical fault, two alternative current limiting strategies are presented with reverse current limiting references, and with current limiting references based on the introduced phase angle regulation. The theoretical results are validated by simulations and experimental results. [ABSTRACT FROM AUTHOR]

A new pulsewidth modulation (PWM) strategy which is an alternative approach of the discontinuous PWM (DPWM) for a three-level neutral-point-clamped (NPC) inverter is proposed in this paper. A three-level NPC inverter is completely mature and very well-established topology in high-power applications. However, the three-level NPC inverter has an inheritance problem of the neutral-point voltage unbalancing due to the split dc-link capacitors. This structure can cause large neutral-point voltage ripple. Furthermore, output currents of the three-level NPC inverter are distorted by the neutral-point voltage ripple. Therefore, the neutral-point voltage must be controlled. In this paper, a new DPWM method using two different offsets for the neutral-point ripple reduction is proposed and the effectiveness of the proposed DPWM method is verified by using the simulation and the experimental results. [ABSTRACT FROM PUBLISHER]

This paper presents a new application of power and voltage balance control schemes for the cascaded H-bridge multilevel inverter (CHMI)-based solid-state transformer (SST) topology. To reduce load on the controller and simplify modulation algorithm, a master–slave control (MSC) strategy is designed for the dual active bridge (DAB) stage. The master controller executes all control and modulation calculations, and the slave controllers manage only device switching and protection. Due to the inherent power and dc-link voltage unbalance in cascaded H-bridge-based SST, this paper presents a compensation strategy based on three-phase dq decoupled current controller. An optimum zero-sequence component is injected in the modulation scheme so that the three-phase grid currents are balanced. Furthermore, to tightly regulate the output voltage of all the DAB modules to target value, a dynamic reference voltage method is also implemented. With this proposed control method, the three-phase grid currents and dc-link voltage in each module can be simultaneously balanced. Finally, simulation and experimental results are presented to validate the performance of the controller and its application to microgrid SST. [ABSTRACT FROM PUBLISHER]

In this paper, a modulation and control method for the new transformerless unified power flow controller (UPFC) is presented. As is well known, the conventional UPFC that consists of two back-to-back inverters requires bulky and often complicated zigzag transformers for isolation and reaching high power rating with desired voltage waveforms. To overcome this problem, a completely transformerless UPFC based on an innovative configuration of two cascade multilevel inverters has been proposed. The new UPFC offers several advantages over the traditional technology, such as transformerless, light weight, high efficiency, low cost and fast dynamic response. This paper focuses on the modulation and control for this new transformerless UPFC, including optimized fundamental frequency modulation for low total harmonic distortion and high efficiency, independent active and reactive power control over the transmission line, dc-link voltage balance control, etc. The new UPFC with proposed control method is verified by experiments based on 4160-V test setup. Both the steady-state and dynamic-response results will be shown in this paper. [ABSTRACT FROM PUBLISHER]

This paper presents an improved dc-link voltage balancing algorithm for a three-level neutral-point-clamped inverter by considering phase current direction. Detailed studies on the effects of change in load current direction on the dc-link capacitor voltages are presented. A maximum value of power factor is numerically derived, above which it affects the capacitor voltage balancing capability. Compared with the previously presented research work, the inputs to the space-vector pulsewidth-modulation block are the three phase currents and the difference between the two capacitor voltages. Depending on the states of the two dc-link capacitor voltages and phase current direction, redundant voltage vector sequences are selected. The selected vectors keep the capacitor voltage deviations within 5% of the total dc-link voltage. Two zero switching vectors (i.e., PPP and NNN) are also removed from all subsectors of the earlier proposed strategy, which one used to produce higher common-mode voltages. Detailed simulation and experimental results are presented in this paper for a 6.0-kW surface permanent-magnet synchronous machine. Both the simulation and experimental results show the required performance of the proposed system. [ABSTRACT FROM AUTHOR]

In order to solve the neutral-point voltage unbalancing problem for three-level inverters, this paper proposes a method to balance the neutral-point voltage for three-level inverters with variable modulation wave offset sinusoidal pulse-width modulation (SPWM) control. Based on the mathematical expressions of neutral-point voltage unbalancing, the factors are studied, which affect the fluctuation of neutral-point voltage. Theoretically the mathematical expressions of the neutral-point voltage with the proposed method are derived, and the mathematical relationship between the fluctuation of neutral-point voltage and the adjusting offset of modulation wave is studied. This proposed method realizes controlling the neutral-point voltage balance by dynamically calculating the offset superimposed to the modulation wave based on SPWM (DCOSPWM). This DCOSPWM method is very simple, which has good steady-state performance and is easy for digital implementation. The simulation results verify the correctness of the theoretical analysis in this paper, and the feasibility and effectiveness of this method is verified by the experiments in the experimental platform of neutral point clamped three-level inverters based on digital signal processor (DSP)-complex programmable logic device (CPLD). [ABSTRACT FROM AUTHOR]

According to the number of segments, the space vector modulation (SVM) can divide into conventional SVM sequence (CSVMS) and special SVM sequence (SSVMS). It is well known that SVM can be equivalently realized by carrier-based pulse width modulation (CBPWM) with a zero component injection in both two-level and three-level inverters. For eight segment CSVMS in three-level inverters, many papers have ever got the injected zero component equation. But similar approach does not work for SSVMS, which has more than eight segments, e.g., 10, 12, or 14. What more, the accurate injected zero component has never been achieved so far. To solve above problems, therefore, a generated decomposition method of modulation wave has been proposed in this paper. By strict theoretical derivation, the same correlation can be extended to SSVMS and the corresponding zero component expression can be acquired. Based on this method, this paper puts a lot attention on the essential feature explanation, mathematical proof, and gives a detailed process to get the zero component equation, using it can realize SSVMS by CBPWM. The simulation and experimental results illustrate that the generated decomposition method of modulation wave is correct, and the unified theory of CBPWM and SVM is verified. [ABSTRACT FROM AUTHOR]

In this paper, we propose model predictive control methods to reduce the common-mode voltage of three-phase voltage source inverters (VSIs). In the reduced common-mode voltage-model predictive control (RCMV-MPC) methods proposed in this paper, only nonzero voltage vectors are utilized to reduce the common-mode voltage as well as to control the load currents. In addition, two nonzero voltage vectors are selected from the cost function at every sampling period, instead of using only one optimal vector during one sampling period. The two selected nonzero vectors are distributed in one sampling period in such a way as to minimize the error between the measured load current and the reference. Without utilizing the zero vectors, the common-mode voltage controlled by the proposed RCMV-MPC algorithms can be restricted within ±Vdc/6. Furthermore, application of the two nonzero vectors with optimal time sharing between them can yield satisfactory load current ripple performance without using the zero vectors. Thus, the proposed RCMV-MPC methods can reduce the common-mode voltage as well as control the load currents with fast transient response and satisfactory load current ripple performance compared with the conventional model predictive control method. Simulation and experimental results are included to verify the effectiveness of the proposed RCMV-MPC methods. [ABSTRACT FROM AUTHOR]

This paper proposes a novel bidirectional inverter, named series ac-link inverter. This three-phase inverter belongs to a new class of partial resonant ac-link converters in which the link is formed by a series ac inductor/capacitor (LC) pair having low reactive ratings. The input and output of this converter can be either dc, ac, single-phase, or multiphase. Therefore, they can appear as dc–dc, dc–ac, ac–dc, and ac–ac configurations. In all of these configurations, the ac capacitor is the main energy-storage element, and the inductor is merely added to facilitate the zero-current turnoff of the switches and their soft turn-on. Due to the zero-current turnoff of the switches in the proposed converter, the use of SCRs with natural commutation is possible as well. Since the current and voltage of the link are both alternating, no bulky dc-electrolytic capacitors are required in this converter. This paper mainly focuses on bidirectional dc to three-phase ac conversion. This single-stage inverter can step up or step down the voltage in a wide range. If galvanic isolation is required a single-phase high-frequency transformer can be added to the link. In the proposed inverter, the power can flow in both directions, and therefore, it is an excellent candidate for battery-utility interface and electric vehicle applications. In this paper, the principles of the operation of the proposed inverter, along with its design and analysis, are studied. Moreover, the performance of the proposed configuration is evaluated in this paper. Both simulation and experimental results are included. [ABSTRACT FROM AUTHOR]

Exploiting the rich switching redundancies of the dual inverter, new hybrid pulsewidth-modulation (PWM) switching methods are proposed in this paper using the degree of freedom of operating the individual inverters independently, in addition to exercising the degree of freedom of controlling the switching action of the individual legs independently. Two voltage entities, namely, common-mode voltage (CMV) and differential-mode voltage are identified in the dual inverter, and all hybrid PWMs are envisaged aimed at reducing and also eliminating the CMV in it. The effects of such attempts on motor shaft voltage and also the motor bearing currents are presented in detail. Furthermore, bearing current profiles of an open-end winding induction motor are also presented with both conventional and hybrid PWMs proposed in this paper. Electric discharge machining discharge currents are completely eliminated with the use of all hybrid PWM methods proposed in this paper. In addition, implications of completely eliminating the CMV are also presented in this paper. All hybrid PWMs proposed in this paper are first simulated using MATLAB and are experimentally verified on a dual two-level inverter feeding a 1.1-kW 415-V 3- $\phi$ open-end winding induction motor drive. [ABSTRACT FROM PUBLISHER]

This paper presents a new multilevel selective harmonic elimination pulse-width modulation (MSHE-PWM) technique for transformerless static synchronous compensator (STATCOM) system employing cascaded H-bridge inverter (CHI) configuration. The proposed MSHE-PWM method optimizes both the dc-voltage levels and the switching angles, enabling more harmonics to be eliminated without affecting the structure of the inverter circuit. The method provides constant switching angles and linear pattern of dc-voltage levels over the modulation index range. This in turns eliminates the tedious steps required for manipulating the offline calculated switching angles and therefore, easing the implementation of the MSHE-PWM for dynamic systems. Although the method relies on the availability of the variable dc-voltage levels which can be obtained by various topologies, however, the rapid growth and development in the field of power semiconductor devices led to produce high-efficiency dc-dc converters with a relatively high-voltage capacity and for simplicity, a buck dc-dc converter is considered in this paper. Current and voltage closed loop controllers are implemented for both the STATCOM and the buck converter to meet the reactive power demand at different loading conditions. The technique is further compared with an equivalent conventional carrier-based pulse-width modulation to illustrate its enhanced characteristics. The effectiveness and the theoretical analysis of the proposed approach are verified through both simulation and experimental studies. [ABSTRACT FROM AUTHOR]

A two-motor drive, supplied by a five-leg inverter, is considered in this paper. The independent control of machines with full dc-bus voltage utilization is typically achieved using an existing pulsewidth modulation (PWM) technique in conjunction with field-oriented control, based on PI current control. However, model predictive control (MPC), based on a finite number of control inputs [finite-control-set MPC (FCS-MPC)], does not utilize a pulsewidth modulator. This paper introduces three FCS-MPC schemes for synchronous current control in this drive system. The first scheme uses all of the available switching states. The second and third schemes are aimed at reducing the computational burden and utilize a reduced set of voltage vectors and a duty ratio partitioning principle, respectively. Steady-state and transient performances are analyzed and compared both against each other and with respect to the field-oriented control based on PI controllers and PWM. All analyses are experimental and use the same experimental rig and test conditions. Comparison of the predictive schemes leads to the conclusion that the first two schemes have the fastest transient response. The third scheme has a much smaller current ripple while achieving perfect control decoupling between the machines and is of low computational complexity. Nevertheless, at approximately the same switching loss, the PI-PWM control yields the lowest current ripple but with slower electrical transient response. [ABSTRACT FROM PUBLISHER]

In this paper, the remedial operation of switch faults will be investigated comprehensively for T-type-three-level-inverter-fed dual three-phase motor drives. The open-circuit switch faults in multiple phase legs are discussed at first. The faulty conditions are classified into five categories. Different remedial strategies, namely Type-I to Type-V schemes, are proposed for different faulty conditions. In particular, three kinds of Type-III fault-tolerant control schemes are proposed by using medium-voltage vectors to synthesize small-voltage vectors, in such a way that the mid-point voltage in a dc link can be stabilized well. Then, the short-circuit faults in both clamping switches and half-bridge switches are investigated. By analysis, their operation conditions are equivalent to conditions loss of both P and N voltage levels and open-phase faults, respectively. Thus, the corresponding remedial strategies can be applied accordingly. Particularly, a voltage compensation control method is proposed for conditions, where open-switch faults coexist with open-phase operation induced by short-circuit faults in half-bridge switches. The validity of all of theoretical analysis and the proposed remedial strategies has been verified by experiments. [ABSTRACT FROM PUBLISHER]

This paper proposes the combination of a novel modified quasi-Z-source (MqZS) inverter with a single-phase symmetrical hybrid three-level inverter in order to boost the inverter three-level output voltage. The proposed single-phase MqZS hybrid three-level inverter provides a higher boost ability and reduces the number of inductors in the source impedance, compared with both the single-phase three-level neural-point clamped quasi-Z-source inverter and the single-phase quasi-Z-source cascaded multilevel inverter. Additionally, it can be extended to obtain the nine-level output voltage by cascading two three-level pulse width modulation switching cells with a separate MqZS and a dc source, which herein is called a single-phase MqZS cascaded hybrid five-level inverter (MqZS-CHI). A modified modulation technique based on an alternative phase opposition disposition scheme is suggested to effectively control the shoot-through state for boosting the dc-link voltage and balancing the two series capacitor voltages of the MqZS. The performances of both the proposed MqZS-CHI and the modulation techniques are verified through simulation and experimental results. [ABSTRACT FROM PUBLISHER]

This paper presents a nine-level active-neutral-point-clamped (ANPC) based multilevel inverter (MLI) topology for grid-connected applications requiring only ten switches. The envisaged structure comprises two parts, namely five-level ANPC unit, and a two-level converter leg whose midpoint is used as another ac terminal. An ad hoc switching state redundancy based modulation strategy is used to ensure that the voltage across the flying capacitor is tightly balanced and is implemented using a look-up table further simplifies the control complexity. The performance and effectiveness of the proposed topology with its control scheme are validated through simulations and experimental tests. Comparison with other MLIs is included to highlight the merits of the proposed topology. From the results, it will be shown that the proposed inverter requires the least part count as compared to other topologies with the same performance and output quality. [ABSTRACT FROM PUBLISHER]

Cascaded H-bridge (CHB) multilevel inverters (MLIs) have been widely used for power electronics systems. While high-voltage blocking across power switches is not a constraint for low voltage applications, the research trend has been oriented to the design of more compact module topologies as an alternative for CHB. Despite the generation of more voltage levels with reduced switch count, the existing module topologies in recent literature take no account of the freewheeling current path during dead-time, thus, inducing multistep jumps in voltage levels and giving rise to undesirable voltage spikes. Addressing this concern, this paper proposes two symmetrical compact-module topologies for cascaded MLI, where freewheeling current path during dead-time is provided for smooth transition between voltage levels to prevent voltage spikes. The proposed 7-level and 13-level compact-modules demonstrated low number of conducting switches for all voltage levels. Comprehensive analysis and comparison with the latest module topologies are conducted. To validate the operation of the proposed compact-module topologies, simulation and experimental results are presented. [ABSTRACT FROM PUBLISHER]

This paper discusses the use of a cascaded multilevel converter for flexible power conditioning in smart-grid applications. The main feature of the proposed scheme is the use of independent dc links with reduced voltages, which makes such a topology an ideal candidate for medium- and high-power applications with increased reliability. The developed control strategy regulates independent dc-link voltages in each H-bridge cell, and allows the selective and flexible compensation of disturbing currents under a variety of voltage conditions without requiring any reference frame transformation. The selective control strategies are based on the decompositions proposed in the conservative power theory, which result in several current-related terms associated with specific load characteristics. These current components are independent of each other and may be used to define different compensation strategies, which can be selective in minimizing particular effects of disturbing loads. Experimental results are provided to validate the possibilities and performance of the proposed control strategies, considering ideal and deteriorated voltage conditions. [ABSTRACT FROM PUBLISHER]