Search

The nine-arm modular multilevel converter (9A-MMC) has been recently proposed as a reduced MMC topology variation for six-phase drive applications, with 25% reduction in the number of employed arms and associated components, compared to a standard dual three-phase MMC, however with a limited output voltage amplitude. This paper proposes a hybrid 9A-MMC comprised of half-bridge submodules (SMs) in both the upper and lower arms, and full-bridge SMs in the middle arms. By employing the negative-voltage state of the full-bridge SMs, the hybrid 9A-MMC avoids the limitations imposed on the dc-link voltage utilization, while achieving further reduction in the component count, compared to a standard 9A-MMC with identical half-bridge SMs. The operating principles of the proposed hybrid 9A-MMC are illustrated with mathematical analysis, whereas its characteristics are verified through both simulation and experimentation. An assessment of the proposed topology quantifying its employed components is also provided, in comparison to other MMC-based six-phase machine drives. [ABSTRACT FROM AUTHOR]

In this study, a cost‐effective HVDC shunt tap with low‐number of relatively low‐voltage semiconductor devices and small‐sized passive components is proposed. The proposed architecture is based on employing three single‐phase half‐bridge Modular Multilevel Converters (MMCs), where the DC sides of MMCs are connected in series across the total DC‐link voltage. The MMCs are adopted instead of conventional Two‐Level Voltage Source Converters (2L‐VSCs) to avoid the complications of series connection of Insulated Gate Bipolar Transistors (IGBTs). The involved MMCs in the suggested architecture are operated with the conventional 2L modulation, which results in insignificant arm inductors and Sub‐Modules (SMs) capacitances (in range of µH and µF, respectively). This, in turn, affects positively the converter cost and footprint. Each arm of the involved MMCs can be considered as a high‐voltage valve of a 2L‐VSC. To maintain the balance of SMs capacitors, each arm of the involved (N + 1)‐level MMC has an extra SM (a balancing SM) to select N out of N + 1 SMs during the turn‐off condition. The operational concept, design, and assessment of the proposed architecture are presented in this study. Simulation results are provided for substantiation of the proposed concept. Finally, a scaled down single‐phase prototype is used for experimental validation. [ABSTRACT FROM AUTHOR]

This article investigates the required modifications to droop control design for optimum operation of Multi-Terminal High-Voltage Direct Current (MTHVDC) systems during line and converter outages. A typical 6-bus MTHVDC system is used in this study. Different scenarios are considered during the design process such as different outage types, violation of power ratings of system components, and variability of wind power injected into the system. A variable droop control gains technique is proposed to ensure minimum power loss and maximum annual energy collection. The study is extended to investigate the effect of employing constant droop control gains calculated during rated conditions on the system performance. Moreover, the results of the constant and the proposed variable droop gain schemes are compared. Simulation results show the effectiveness of the proposed techniques for designing optimum droop gains during abnormal conditions. Additionally, general guidelines are presented for the implementation of the proposed techniques. [ABSTRACT FROM AUTHOR]

This paper presents a drive system based on a modular multilevel converter (MMC) with high-frequency magnetic channels between adjacent-arm submodules (SMs), suitable for medium-voltage, high-power three-phase variable-speed machines. The configuration employs chains of dual half-bridge (DHB) modules linking adjacent SMs of three-phase symmetrical arms. The DHB modules are operating as power channels enabling energy exchange to restore the power imbalance among the SM capacitors. This allows arms’ ripple-powers to be entirely decoupled through bidirectional power transfer between adjacent-arm SMs, resulting in a near ripple-free SM capacitor voltage profile. Therefore, the MMC common problem of wide voltage fluctuation across SM capacitors is comprehensively solved, independent of the operating frequency. Additionally, a significant reduction in the sizing requirement of SM capacitance is achieved. The configuration is able to drive multimegawatt machines from standstill to the rated speed at the rated torque operating condition. The operating principle of the proposed MMC configuration is explained and necessary mathematical analysis is derived. Features and viability of the proposed drive system are verified through simulation and experimentation. [ABSTRACT FROM AUTHOR]

Staphylococcus epidermidis, the most frequently isolated coagulase-negative staphylococcus, is the leading cause of infection related to implanted medical devices (IMDs). This is directly related to its capability to establish multilayered, highly structured biofilm on artificial surfaces. At present, conventional systemic therapies using standard antimicrobial agents represent the main strategy to treat and prevent medical device-associated infections. PCR assay was used to detect the presence of icaA gene in the bacterial isolates, and the micro titter plate assay was used to detect the ability for biofilm production. This study was aimed to detect the phenotypic and genotyping of virulence factors of S.epidermidis bacteria isolated from patients with variety infections from different clinical specimens. As a result, the biofilm production ability was strongly associated with the presence of icaA gene in the bacterial isolates. [ABSTRACT FROM AUTHOR]

This paper proposes a medium-/high-voltage high-power hybrid modular dc–dc converter to interconnect two different dc-voltage levels in medium-/high-voltage dc grids. The converter consists of half-bridge submodules (SMs) rated at a moderate voltage level, i.e., series connection of semiconductor devices is avoided while connecting two high dc-voltage levels. The proposed architecture provides self-balancing operation, i.e., unlike conventional modular converters, no need for capacitor voltage measurement, which enhances the system reliability and simplicity. Sequential charging/discharging of SMs capacitors is adopted in the proposed approach to ensure a self-balanced operation. The proposed architecture can provide a high conversion ratio as well as power transfer in both directions, i.e., bidirectional dc–dc converter. Detailed illustration of the proposed approach operational concept, design, and overall control system is presented. Simulation and experimental results are presented to show the viability of the proposed configuration and validate the claims. [ABSTRACT FROM AUTHOR]

The application of multiphase machines in high-power applications is now a recognized alternative, thanks to their higher fault-tolerance when compared with standard three-phase systems. Although multiphase machines with multiples of three-phase winding sets have been favored in many applications, literature has shown that machines with a prime number of phases, such as five-phase machines, generally outperform other phase orders, especially in terms of machine torque density. One of the major problems when dealing with a prime number of phases either in academic research or industrial applications is the special stator design. This paper provides a general technique to rewind standard off-the-shelf three-phase stator frames with any general prime phase order while preserving the same copper volume. The proposed winding layout is derived using the star of slots theory and the concept of stator winding shifting. Finite-element simulations are used to investigate examples with different phase orders, while experimental investigation is carried out to corroborate the proposed concept by rewinding a standard three-phase stator as a five-phase machine. [ABSTRACT FROM AUTHOR]

Pulse forming networks and Marx generators are the classical rectangular waveform pulse generators (PGs). They are inflexible and their capacitors must be fully charged to the required voltage from 0 V before delivering each high-voltage (HV) pulse. They are only able to generate unipolar pulses; if bipolar pulses are sought another generator fed from a negative supply voltage is added. Recently, several power electronics based PGs have been proposed. This study presents an HV power electronics based PG, which is based on half-bridge modular multilevel converter (MMC) sub-modules (SMs) charged sequentially in a voltage-boost mode. Each SM capacitor and main switch form a boost converter with the charging input supply and inductor. As a result, all SM capacitors are charged to a voltage greater than the input. During the discharging process, the SM capacitors are connected in series, producing a rectangular HV pulse across the load. The proposed charging method allows a reduction in the converter footprint in comparison with recently proposed MMC sequentially charged PG topologies. Although only rectangular pulse waveforms are sought in this study, an SM-capacitor voltage balance method allows multilevel pulse generation. The viability of the proposed converter is confirmed by MATLAB/Simulink simulation and scaled-down experimentation. [ABSTRACT FROM AUTHOR]

The nine-phase six-terminal induction machine (IM) has been recently proposed as a promising contender to the conventional asymmetrical six-phase type in terms of torque density, stator winding simplicity, and fault-tolerant capability. The stator is composed of nine phases, which are connected in a fashion to only provide six stator terminals. Therefore, this connection combines the high performance of a nine-phase winding with the terminal behavior of a six-phase machine. This paper introduces the machine mathematical model based on the vector space decomposition (VSD) modeling approach. The required current and voltage sequence transformation matrices are derived such that the machine is mathematically regarded as an equivalent six-phase IM with only three decoupled subspaces. This way, the same VSD-based controller structures conventionally applied to six-phase-based systems can be preserved. A 1.5-hp prototype IM is used to experimentally validate the machine model under both healthy and open-phase conditions. [ABSTRACT FROM AUTHOR]

In this paper, a dc–ac buck converter is proposed as a grid-side converter in high voltage dc (HVdc) transmission systems for high-power renewable energy source grid integration. The proposed architecture consists of multimodules of half-bridge voltage source converters (HB-VSCs). The dc terminals of the HB-VSCs are connected in series across the entire dc link (i.e., capacitor tapped), whereas their ac outputs are connected to multiwinding transformers to provide the three-phase terminals for ac grid integration. The proposed grid-connected capacitor-tapped multimodule converter (CT-MC) architecture, inspired from the HVdc shunt tap proposed by ABB, provides a dc–ac conversion with a relatively moderate voltage rating of semiconductor devices. It also provides operation with a lower number of semiconductor devices, gate driver circuits, voltage sensors, and lower total MVA rating of semiconductor devices (67%) compared with the conventional three-phase HB modular multilevel converter, which positively affects the system cost and reduces the computational burden of the employed controller. In this paper, the operational concept and control of the CT-MC are presented along with a capacitor voltage balancing approach. Simulation results are presented during normal and abnormal conditions to show the viability of the proposed architecture. Finally, a scaled down prototype for the CT-MC is employed to validate the converter operation. [ABSTRACT FROM AUTHOR]

Idiopathic myointimal hyperplasia of the mesenteric veins (IMHMV) is caused by proliferation of smooth muscle cells in the wall of small mesenteric veins and venules with accumulation of a proteoglycan matrix leading to a non-thrombotic, non-inflammatory venous occlusion resulting in venous ischemia. IMHMV is a rare and poorly understood disease, with <20 case reports in the literature. The purpose of this report is to describe the case of a 63-year-old man who presented with this condition that resulted in colonic ischemia necessitating surgical resection. The cause of IMHMV in this patient was attributed to a Chinese herbal supplement used for degenerative osteoarthritis of the knees. A brief review of the literature is provided along with the case report. [ABSTRACT FROM AUTHOR]

Detection of rotor slot and other eccentricity related harmonics in the line current of a three phase induction motor is important both from the viewpoint of sensorless speed estimation as well as eccentricity related fault detection. However, it is now clear that not all three phase induction motors are capable of generating such harmonics in the line current. Recent research has shown that the presence of these harmonics is primarily dependent on the number of rotor slots and the number of fundamental pole pairs of the machine. While the number of fundamental pole pairs of a three phase induction motor usually is within one to four (higher pole pairs are generally avoided due to increased magnetizing current), the number of rotor slots can vary widely. The present paper investigates this phenomenon further and obtains a hitherto nebulous theoretical basis for the experimentally verified results. Detailed coupled magnetic circuit simulation results are presented for a four pole, three phase induction motor with 44, 43, and 42 rotor slots under healthy, static, dynamic and mixed eccentricity conditions. The simulation is flexible enough to accommodate other pole numbers also. These simulations are helpful in quantifying the predicted harmonics under different combinations of load, pole pair numbers, rotor slots and eccentricity conditions, thus making the problem easier for drive designers or diagnostic tools' developers. Data from three different induction machines, namely, a 4 pole, 44 bar, 3 HP, a 4 pole, 28 bar, 3 HP, and a 2 pole, 39 bar, 100 HP motor have been used to verify the results experimentally. The simulation and the experimental results clearly validate the theoretical findings put forward in this paper. Index Terms--Eccentricity, induction motor fault diagnosis, sensorless speed estimation.

Here, a new bi‐directional hybrid modular non‐isolated DC–DC converter is proposed where it consists of a boost converter (BC) fed from the high‐voltage (HV) side. At the BC output stage, a certain number of half bridge submodules (HB‐SMs) is connected across the BC switch. During the turn‐on period of BC switch, the HB‐SMs are connected sequentially to the low‐voltage (LV) side, which results in charging/discharging their capacitors from/into the LV side. While, during the turn‐off period, the LV side is bypassed and the HB‐SMs capacitors are connected in series across the BC output stage, which results in discharging/charging them into/from the HV side. The power flow is controlled in both directions by controlling the duty cycle. The proposed configuration provides self‐balancing operation thanks to the sequential connection of HB‐SMs capacitors, and it also provides the ability to operate with high conversion ratios. Illustration and analysis of the proposed converter and its closed‐loop controller are presented. A full design of the values and ratings of the involved components are presented. Simulation study for a 2.5 MW (25 kV/10 kV) DC–DC converter is presented. Finally, experimental results for a downscaled prototype are presented for validation. [ABSTRACT FROM AUTHOR]

This paper presents a dual modular multilevel converter (MMC) topology that utilizes energy exchange between adjacent-arm submodules (SMs), operating with out-of-phase modulation. The proposed configuration is applicable to medium-voltage high-power variable-speed drives incorporating open-end stator winding machines. A novel concept of power decoupling between adjacent-arm SMs in the dual MMC topology is realized through high-frequency transformer-based dc–dc converter modules. This concept offers a significant reduction in the sizing requirement of the SM capacitance and the stored energy in the MMC system, while avoiding the problem of wide voltage fluctuations of SM capacitors, especially at low operating frequencies. The proposed configuration can produce dc voltage; therefore, a machine speed range from zero speed to the rated speed is possible under the rated torque operating condition. The operating principles of the proposed dual MMC configuration are elaborated and necessary mathematical analysis is derived. Simulation and experimental results verify the concept of the proposed drive configuration. [ABSTRACT FROM AUTHOR]

This paper studies the postfault control of a nine-phase six-terminal induction machine (IM) during single open-line fault, which was recently proposed for high-power medium-voltage applications as a promising alternative to conventional six-phase IMs. The required optimal reference currents to provide prefault loading conditions under one-line open are derived using the two most common optimization criteria employed in multiphase drives, namely, maximum torque and minimum loss modes. A postfault controller, based on conventional decoupling Clarke's transformation, is then used to ensure the same controller structure under all conditions. Consequently, the machine characteristic curves, achievable torque, and stator copper losses under these different modes are compared. A comparison with a conventional asymmetrical six-phase winding is also given. A 1.5-Hp prototype IM is used for experimental verification. [ABSTRACT FROM PUBLISHER]

This study proposes an isolated on‐board integrated battery charger using an interior permanent magnet (IPM) machine with a nine‐slot/eight‐pole combination or its multiples, and equipped with a non‐overlapped fractional slot concentrated winding. The proposed winding layout comprises three three‐phase winding sets that are connected in such a way as to provide six motor terminals. Hence, a six‐phase or two three‐phase converters will be required for propulsion. Under motoring mode, the machine can be effectively regarded as a six‐phase machine, which provides a high fault‐tolerant capability, and allows for a 'limp home' mode of operation. Additionally, all magneto motive force subharmonics are eliminated, which significantly reduces the induced rotor eddy current losses, when compared with a conventional three‐phase motor having the same slot/pole combination. In battery charging mode, the winding is reconfigured, so that the machine is considered as a three‐phase to six‐phase rotating transformer. A 40 kW IPM machine is designed and simulated under different modes of operation using two‐dimensional finite element analysis to validate the proposed concept. A small‐scale prototype machine is also used for experimental validation. [ABSTRACT FROM AUTHOR]

High-voltage (HV) pulses are used in electroporation to subject pulsed electric field (PEF) onto a sample under treatment. Pulse-waveform shape, voltage magnitude, pulse duration, and pulse repetition rate are the basic controllable variables required for particular PEF application. In practice, a custom-made pulse generator is dedicated for each PEF application with limited flexibility in changing these variables. In this paper, a universal pulse-waveform generator (UPG) is proposed, where the controller software algorithm can manipulate a basic generated multilevel pulse waveform to emulate many different PEF pulse waveforms. The commonly used PEF HV pulse waveforms can be generated as bipolar or monopolar with controllable pulse durations, repetition times, and voltage magnitudes. The UPG has the ability to generate multilevel pulses that have controllable $dv/dt$, which allows reduction of the electromagnetic interference generated by the converter. The UPG topology is based on half-bridge modular multilevel converter (HB-MMC) cells forming two transition arms in conjunction with two bistate arms, together creating an H-bridge. The HB-MMC cell capacitors provide a controllable energy source which charge from the dc input supply and discharge across the load, while the two bistate arms allow charging the HB-MMC cell capacitors. Hence, the UPG topology offers modularity, redundancy, and scalability. The HB-MMC individual cell capacitance is low and the cell voltages are balanced by employing the sorting and rotating algorithm used in conventional HB-MMC topologies for HV dc transmission applications. The viability of the proposed UPG converter is validated by MATLAB/Simulink simulation and scaled-down experimentation. [ABSTRACT FROM PUBLISHER]

In this paper a Four-Arm Three-Phase MMC (4A-TPMMC)-based DC–AC converter is proposed. The proposed converter generates a three-phase output voltage using a lower number of components, which reduces the converter complexity and cost. The concept of the proposed approach is presented in this paper. A comparison between the conventional Six-Arm Three-Phase MMC (6A-TPMMC) and the proposed 4A-TPMMC is conducted. Two simulation models are built, one for the 6A-TPMMC, and the other for the proposed 4A-TPMMC. The simulations are carried out for the same number of submodules per arm and the same AC output voltage magnitude. Moreover, a case study using the proposed 4A-TPMMC, as a three-phase medium voltage motor drive, is considered. Finally, an experimental validation for the proposed 4A-TPMMC is presented to prove the viability of the claimed contributions. [ABSTRACT FROM PUBLISHER]

High-voltage (HV) pulse generators (PGs) are the core of pulsed electric field applications. Applying HV pulses produces electrical pores in a biological cell membrane, in which if the size of the pores increases beyond a critical size, the cell will not survive. This paper proposes a new HV-PG based on the modular multilevel converter with full-bridge submodules (FB-SMs). In order to alleviate the need of complicated sensorless or sensor-based voltage balancing techniques for the FB-SM capacitors, a dedicated self-regulating charging circuit is connected across each FB-SM capacitor. The individual capacitor charging voltage level is obtained from three successive stages, namely, convert the low-voltage dc input voltage to a high-frequency square ac voltage, increase the ac voltage level via a nanocrystalline step-up transformer, and rectify the secondary transformer ac voltage via a diode FB rectifier. The HV bipolar pulses are formed across the load in a fourth stage through series connected FB-SMs. The flexibility of inserting and bypassing the FB-SM capacitors allows the proposed topology to generate different pulse-waveform shapes, including rectangular waveforms with specifically reduced dv/dt and ramp pulses. The practical results, from a scaled-down experimental rig with five FB-SMs and a 1-kV peak-to-peak pulse output, validate the proposed topology. [ABSTRACT FROM PUBLISHER]

Conventional Modular Multilevel Converter (MMC) with Half-Bridge Sub-Modules (HB-SMs) can be used effectively as a solid-state high-voltage pulse generator to chop a high-voltage dc input into a bipolar pulsed output voltage without employing neither high-voltage semiconductor switches nor series-connected switches. Nonetheless, its boosting capability is constrained. In this paper, a hybrid boost MMC-based bipolar high-voltage pulse generator is proposed where each arm contains a combination of Full-Bridge SMs (FB-SMs) and HB-SMs. The HB-SMs and FB-SMs have the same rated voltage. The proposed approach is able to generate bipolar pulses, and operates with a wide range of boosting capability. Detailed illustration of the proposed configuration and its operational concept are presented. Simulation models for the proposed approach are built, for different FB-SMs to HB-SMs ratios, using Matlab/Simulink platform. Experimental results for a scaled-down prototype are presented to validate the concept. [ABSTRACT FROM PUBLISHER]

High-voltage (HV) pulses are used in pulsed electric field (PEF) applications to provide an effective electroporation process, a process in which harmful microorganisms are disinfected when subjected to a PEF. Depending on the PEF application, different HV pulse specifications are required such as the pulse-waveform shape, the voltage magnitude, the pulse duration, and the pulse repetition rate. In this paper, a generic pulse-waveform generator (GPG) is proposed, and the GPG topology is based on half-bridge modular multilevel converter (HB-MMC) cells. The GPG topology is formed of four identical arms of series-connected HB-MMC cells forming an H-bridge. Unlike the conventional HB-MMC-based converters in HVdc transmission, the GPG load power flow is not continuous which leads to smaller size cell capacitors utilization; hence, smaller footprint of the GPG is achieved. The GPG topology flexibility allows the controller software to generate a basic multilevel waveform which can be manipulated to generate the commonly used PEF pulse waveforms. Therefore, the proposed topology offers modularity, redundancy, and scalability. The viability of the proposed GPG converter is validated by MATLAB/Simulink simulation and experimentation. [ABSTRACT FROM PUBLISHER]

The conventional unipolar Marx generator can be employed for bipolar pulsed electric field by adding a high-voltage H-bridge at the load side which necessitates stacked switches. Alternatively, bipolar Marx generator with low-voltage switches can be employed. The existing bipolar Marx generators are typically fed from dc supplies, where polarized capacitors are employed. The capacitance of involved capacitors is selected such that the total energy stored in the generator's capacitors is higher than the bipolar pulse energy. As a result, polarized capacitors with relatively high capacitances are required. In addition, a high number of controlled switches per stage are required (at least four switches per stage). In this paper, a new solid-state bipolar Marx pulse generator with only three controlled switches per stage is proposed. The proposed generator is fed from sinusoidal/square ac voltage and non-polarized capacitors with low capacitance are employed. The proposed bipolar Marx-generator can be used effectively with resistive loads for exponential pulse generation. A detailed illustration of the proposed approach is presented and a discussion, to elucidate the differences between the proposed pulse generator and the other existing ones, are presented. Simulation results for the proposed pulse generator are presented to validate the concept. Finally, experimental results have been obtained from a low-voltage model of the proposed generator. [ABSTRACT FROM AUTHOR]

In this study, a new transformerless wind energy conversion system to integrate high‐power multi‐phase permanent magnet wind generators to medium‐voltage local grids is presented. The proposed converter topology consists of multi‐half‐bridge modules with a high ac–direct current (dc) boosting capability. Each phase of an open winding multi‐phase generator is connected to the ac side of a half‐bridge module, whereas the dc sides of the half‐bridge modules are connected in series forming the high‐voltage dc‐link output. The proposed architecture facilitates the employment of semiconductor switches with a relatively low‐voltage rating, which equals the dc‐link voltage divided by the number of generator phases. A detailed analysis of the proposed architecture along with the required closed‐loop control is presented. The proposed architecture is simulated under different operating conditions using a typical 2 MW system, while the experimental validation is carried out using a low‐scale prototype converter. [ABSTRACT FROM AUTHOR]

This paper presents a new high-voltage pulse generator, which is based on positive and negative buck-boost (BB) converters fed from a relatively low voltage dc supply. The proposed generator is able to generate unipolar or bipolar high-voltage pulses via operating the BB converters with series or parallel connected outputs respectively using a common input dc source. The components of each converter are rated at half of the pulsed voltage magnitude in the unipolar mode. The converters in the proposed pulse generator operate in discontinuous conduction mode. This enhances system efficiency, as the circuit only operates when it is desired to generate a pulsed output voltage, otherwise the circuit is switched to idle mode with zero current. Detailed illustration of the proposed approach is presented along with a full design of the system components for given output pulse specifications. Finally, simulation and experimental results are presented to validate the proposed concept. [ABSTRACT FROM PUBLISHER]

Pulsed electric field is a commonly used and effective disinfection method in drinking water treatment applications. In this paper, a transformerless unipolar/bipolar high-voltage pulse generator is presented with well-regulated pulsed output voltage for drinking water treatment via underwater pulsed corona discharge. The proposed high-voltage pulse generator is fed from a relatively low-voltage dc supply. Then, capacitor–diode voltage multiplier centrally fed from a dc–dc boost converter is used to elevate the input voltage to a proper high-voltage level. Finally, a modular multilevel converter is employed to chop the elevated voltage into unipolar or bipolar pulsed output voltage (based on the user selection). The suggested arrangement provides a high-voltage gain with relatively low-voltage components, i.e., neither high-voltage nor series-connected components are needed in the proposed approach. A comparison between the proposed approach and the other Marx-Based pulse generators has been held to show the merits of the proposed approach. A detailed design of the generator passive components and semiconductor devices has been presented. Simulation and experimental results are presented for the unipolar as well as the bipolar pulsed output to validate the proposed concept. [ABSTRACT FROM AUTHOR]

Bipolar repetitive high-voltage pulse generators are commonly used in modern pulsed power applications. Conventionally, bipolar high-voltage pulses can be generated by adding a high-voltage H-bridge at the output stage of a unipolar high-voltage pulse generator which increases complexity and cost of the bipolar high-voltage pulse generator. In this paper, a boost-inverter-based bipolar high-voltage pulse generator with high-voltage gain is proposed. The proposed generator can provide high-voltage bipolar output pulses with the desired specifications from a low input dc voltage. The proposed generator is based on employing two bidirectional boost dc–dc converters, where the load is connected differentially between the boost converters’ output terminals. In the proposed approach, four controlled switches are required. Only two out of these four switches are rated at the high-voltage output level which affects positively the system cost. A detailed illustration of the proposed approach along with the design of its passive components is presented in this study. Simulation and experimental results are used to validate the proposed approach. [ABSTRACT FROM AUTHOR]

This paper proposes a new winding layout for high-power medium-voltage nine-phase induction machines (IMs) based on a single-layer concentrated winding layout having a unity winding factor. The machine is fundamentally an asymmetrical nine-phase IM, where phases are connected in such a way as to provide six terminals that are fed from two three-phase inverters. Compared to a conventional asymmetrical six-phase IM with the same stator and copper volumes, it provides improved torque density, a higher torque/current ratio, and a simpler winding layout. Finite-element simulation is used to compare the proposed winding layout with a conventional split-phase six-phase IM to assess the claimed merits. A 1.5-hp prototype IM is also used for experimental verification. The experimental results are given under both healthy and fault conditions, where the faulty converter is completely disabled. The achievable derating factors under this case are then given and compared with those of conventional six-phase IMs. [ABSTRACT FROM PUBLISHER]

The half‐bridge modular multilevel converter (HB‐MMC) is one of the most promising topologies for high‐voltage direct current (HVDC) systems. Unlike full‐bridge MMC (FB‐MMC) and clamp double sub‐module MMC (CDSM‐MMC), HB‐MMCs are defenceless against DC side faults. Different types of DC circuit breakers (DC CBs) assisted with arrester banks/damping resistors such as solid‐state CB and hybrid DC CBs can be used to interrupt the DC fault current. Arrester banks are used to protect against overvoltage after interrupting the fault current and in turn to demagnetise the circuit inductors. The main disadvantage of the arresters is that they forcibly break apart when they are overloaded. In this study, an arrester‐less fault current limiter is proposed for HB‐MMC configuration, which provides an opposing voltage during the DC side fault. This is achieved by inserting external pre‐charged capacitors in the DC current path during the fault. The selection of these external capacitors, their suitable initial voltages, and their charging stations are also presented in this study. A comparison between the proposed scheme and the CDSM‐MMC has been held as well. The proposed protection scheme is assessed using a simulation study for a point‐to‐point nine‐level HB‐MMC‐based HVDC system. [ABSTRACT FROM AUTHOR]

Repetitive high pulsed electric field (PEF) is an effective method to kill microorganisms and bacteria in water treatment applications. The PEF can be generated by applying high-power electromagnetic pulse across the sample to be treated. There are two main types of high-voltage pulse generators, namely, unipolar and bipolar. In this paper, a full-bridge submodule-based modular high-voltage pulse generator, having the ability to generate unipolar and bipolar high-voltage pulses with different shapes from a relatively low-voltage input dc supply, is proposed. In the proposed configuration, relatively low-voltage insulated gate bipolar transistors (IGBTs) are required to generate the high-voltage bipolar pulses. A thyristor rated at the level of the pulsed output voltage is required in the proposed configuration to bypass the load during the charging process of capacitors. In the proposed approach, a thyristor is used instead of the self-commutated high-voltage switch (e.g., series-connected IGBTs), as thyristors are available with high-voltage ratings and possess inherent reverse voltage blocking capability. A detailed illustration of the proposed configuration and its operational concept are introduced in this paper. Simulation and experimental results are presented to validate the proposed approach. [ABSTRACT FROM AUTHOR]

The combined star/pentagon connection of five-phase induction machines was recently demonstrated as a promising compromise between conventional star and pentagon connections. It combines the advantages of both star and pentagon connections without any additional hardware for winding changeover. This connection is based on two five-phase single layer concentrated winding sets shifted in space by π/10 and connected in a combined star/pentagon configuration to provide five-phase terminals. Since the combined star/pentagon connected induction machine is fundamentally an asymmetrical ten-phase machine, the machine mathematical model possesses additional subspaces, which affect the behavior of the machine especially under open line conditions. Starting from the conventional five-phase and m -bar squirrel cage induction machine model, the phase-variable model of the combined star/pentagon connection is introduced in this paper. The corresponding equivalent dq model with five decoupled subspaces, which can account for air gap harmonics up to ninth order, is then derived. Finally, it was shown that the machine model could be simply approximated with only two subspaces similar to a conventional five-phase induction machine with sinusoidally distributed winding, where the flux produced by the nonfundamental subspace could be neglected. The model is verified using a 1 kW prototype five-phase induction machine. [ABSTRACT FROM PUBLISHER]

Differential-mode buck-boost inverters have merits such as reduced switch number, ability to provide voltages higher or lower than the input voltage magnitude, improved efficiency, reduced cost and size, and increased power density, especially in low-power applications. There are five buck-boost inverters that can provide flexible output voltage without the need of a large electrolytic input side capacitor, which degrades the reliability of inverters. The continuous input current of these inverters is appropriate for maximum power point tracking operation in photovoltaic and fuel cells applications. Three of the five inverters can be isolated with high-frequency-link transformers where the common-mode leakage current can be mitigated. However, the performance and control of such converters have not been discussed in detail. In this paper, the five possible single-stage three-phase differential-mode buck-boost inverters with continuous input current are investigated and compared in terms of total losses, maximum ripple current, total harmonic distortion, and device and passive element ratings. In addition, the possible methods are presented for eliminating the input third-order harmonic current, resulting from the stored energy in the passive elements, as well as the output second-order harmonic currents. The ability for isolating the input and output sides of the inverters with a small–high frequency transformers is discussed. A changeable-terminal 2.5-kW bidirectional inverter is used to validate the design flexibility of the inverter topologies, when digital signal processor-controlled. [ABSTRACT FROM AUTHOR]

Repetitive Pulsed Electric Field (PEF) is a common technique for disinfecting liquids. By applying adequate PEF across germ cell membranes, an irreversible electroporation process, and cell destruction can be achieved. The PEF can be generated by applying a repetitive pulsed voltage using a high-voltage pulse generator across the cell membrane. Unipolar and bipolar high-voltage pulse generators are commonly used. Bipolar pulse generators can be implemented by employing a unipolar generator with an H-bridge output stage. The main disadvantage of this method is that the switches of the H-bridge are rated at the output high-voltage level, i.e. series-stacked semiconductor devices should be employed with static and dynamic voltage sharing to implement high-voltage switches. In this paper, a half-bridge submodule-based bipolar modular high-voltage pulse-generator fed from a relatively low-voltage dc supply is proposed. In the proposed approach, relatively low-voltage Insulated Gate Bipolar Transistors (IGBTs) are required to generate the high-voltage bipolar pulses. A detailed illustration of the proposed concept is presented. Simulation results are used to assure the viability of the proposed concept. Finally, experimental results have been obtained from a low-voltage model of the proposed generator. [ABSTRACT FROM AUTHOR]

The role of irreversible electroporation using pulsed electric field is to generate high-voltage (HV) pulses with a predefined magnitude and duration. These HV pulses are applied to the treatment chamber until decontamination of the sample is completed. In this paper, a new topology for HV rectangular pulse generation for water disinfection applications is introduced. The proposed topology has four arms comprised of series-connected half bridge modular multilevel converter cells. The rectangular pulse characteristics can be controlled via the software controller without any physical changes in power topology. The converter is capable of generating both bipolar and monopolar HV pulses with microsecond pulse durations at high a frequency rate with different characteristics. Hence, the proposed topology provides flexibility by software control, along with hardware modularity, scalability, and redundancy. Moreover, a cell’s capacitance is relatively small, which drastically reduces the converter footprint. The adopted charging and discharging process of the cell capacitors in this topology eliminate the need of any voltage measurements or complex control for cell-capacitors voltage balance. Consequently, continuity of converter operation is assured under cell malfunction. In this paper, analysis and cell-capacitor sizing of the proposed topology are detailed. Converter operation is verified using MATLAB/Simulink simulation and scaled experimentation. [ABSTRACT FROM AUTHOR]

Adjustable-speed drives based on multiphase motors are of significant interest for safety-critical applications that necessitate wide fault-tolerant capabilities and high system reliability. Although multiphase machines are based on the same conceptual theory as three-phase machines, most undergraduate electrical machines and electric drives courses do not cover this topic. Setting aside the analysis challenges addressed in state-of-the-art literature, undergraduate electrical machines and power electronics courses are a good opportunity for students to understand the main concepts underlying such electric drive systems. This paper presents an adjustable-speed multiphase drive system senior project for electrical engineering undergraduate students that addresses their attainment of the course's learning outcomes. Eight of the course's students were assigned to build the multiphase variable-speed motor drive system. From a pedagogical point of view, this paper describes the methodology of using a senior project to engage students through experiential learning of electric drive systems, which span disciplines such as electrical machines, control, power electronics, and electronics. Students acquire both technical skills and soft skills, which are evaluated through various assessment activities. A number of lessons for future work have been drawn from the experience of applying this project-based learning approach. [ABSTRACT FROM AUTHOR]

Differential-mode inverter topologies are promising for renewable energy generation since they offer advantages such as passive elements sizes reduction, having decreased power losses and reduced total cost. Single phase buck-boost differential-mode current-source inverters (DMCSIs) can deliver wider range of output voltage above or below the input dc voltage, which is necessary for high-efficiency modern renewable energy applications. Since these inverters have continuous input currents, they are suitable for maximum power point tracking (MPPT) operation of photovoltaic systems. Yet, the investigation, operation and implementation of these types of inverters have not been extensively discussed. As a drawback, the total dc side input current of a single-phase inverter consists of a dc component and an undesirable ac component. This ac component frequency is double the output voltage frequency and thus it affects MPPT resulting in reduced total efficiency. In this study, five promising DMCSIs are proposed and compared in terms of their total efficiencies, high-frequency ripple current in the dc side, total harmonic distortion, devices sizes and ratings. Moreover, the sliding mode controller's design and possible methods of eliminating the input second harmonic current are discussed. 2.5 kW bidirectional inverters are implemented to confirm the design flexibility of the proposed DMCSIs. [ABSTRACT FROM AUTHOR]

This paper presents a new configuration for integrated on-board battery chargers of electric vehicles (EVs) incorporating symmetrical six-phase machines. The configuration proposes an exclusive utilization of a nine-switch converter (NSC) along with the machine windings during both propulsion and charging of EVs. The proposed configuration has the advantage of employing a reduced number of components in both the EV (on-board) and charging station (off-board), with the privilege of avoiding machine electromagnetic torque production during charging/vehicle-to-grid (V2G) mode of operation. During charging/V2G mode, the NSC is turned into a conventional three-phase pulse width modulation rectifier and is directly connected to the three-phase mains through the machine windings. Conventional three-phase transformers can be employed for galvanic isolation. Switching between propulsion and charging modes is carried out using a simple hardware reconfiguration. Control schemes for both propulsion and charging/V2G modes are elaborated, along with the principles of operation of the NSC. Experimental results are provided to validate the theoretical deductions for the different operating modes. [ABSTRACT FROM PUBLISHER]

In many applications, interior permanent magnet synchronous machines (IPMSMs) with fractional slot concentrated windings (FSCWs) are considered promising candidates in terms of higher power density and efficiency. In addition, employing a multiphase stator winding improves the drive train availability and increases reliability. This study investigates the effect of applying stator shifting to five‐phase FSCW winding IPMSMs to suppress the effect of the slot harmonics by doubling the number of slots. In this case, the winding coil pitch will be two, which stands as a compromise between single‐tooth and distributed winding topologies. This highly improves the air gap flux distribution, significantly reduces both rotor core and magnet eddy current losses, and increases saliency ratio and reluctance torque component. Moreover, an improved performance under fault conditions, in terms of lower torque ripple, and core and magnet losses, adds to the main advantages of this technique. Various slot/pole combinations suitable for five‐phase machines are investigated. A full simulation case study based on two‐dimensional finite element analysis is applied to the 20‐slot/18‐pole stator with single‐tooth winding under both healthy and open‐circuit phase fault cases. [ABSTRACT FROM AUTHOR]

The steady-state modeling of multiphase induction machines (IMs) with m phases under open-line fault conditions is usually carried out based on symmetrical component theory. Hence, the estimation of the machine characteristic curves usually involves complex mathematical calculations and inversion of high-order matrices, which complicates the analysis. Moreover, the effect of the different subspaces’ impedances on the machine performance cannot be easily recognized using this modeling technique. Instead, this paper presents the first attempt to derive a simple equivalent circuit for a five-phase IM under open-line conditions that includes the effect of all subspaces in a single circuit. The derivation is carried out for both star and pentagon connections. The equivalent circuit can be a simple technique to explain the advantages obtained from a pentagon connection compared to the star connection under open-circuit faults. It can also be used to derive a simple expression for torque gain and torque ripple magnitude for different stator connections based on the circuit parameters. The derived equivalent circuits are verified using a 1-kW five-phase prototype machine. [ABSTRACT FROM PUBLISHER]

High-Voltage pulse generators are commonly used in biotechnology, medicine, industrial applications, food processing and drinking water purification. The dc-dc boost converter has been used before in pulsed applications for its ability to amplify a relatively low input dc voltage to a high-voltage output. A high-voltage solid-state chopping switch is then used to chop the generated high output voltage. In this work, a boost-converter based ringing circuit with high voltage gain is proposed for water treatment applications. The basic concept of the proposed approach depends on operating the boost converter under discontinuous current conduction. With the proposed approach, the chopping high-voltage switch at the output stage is eliminated, which positively affects the system cost and efficiency. A full-design of the circuit and passive components is presented to ensure that the desired pulse specifications are achieved. The proposed approach has been validated using simulation and experimental results. [ABSTRACT FROM AUTHOR]

In order to generate bipolar high-voltage (HV) pulses across certain load from HV dc (HVdc) power supply, a voltage source inverter (VSI) stage should be inserted between the load and the supply. In order to meet the required HV level, series connection of semiconductor devices should be employed with dynamic voltage sharing between the involved devices. Modular multilevel converter (MMC) can be used instead of the conventional two-level VSI to alleviate the complexity introduced by the deployment of series-connected devices. The voltage level of the HVdc power supply and the voltage rating of the available semiconductor devices determine the suitable number of MMC voltage levels ( $N$ ). Capacitor voltage balancing is a vital issue for proper operation of the MMC. In general, conventional sensor-based balancing techniques require a significant amount of measurements, which increases the complexity of the system. In addition, the high dv/dt during switching times causes electromagnetic interference, which may adversely affect the accuracy of the measurements. In this paper, a sensorless voltage balancing technique is proposed for the MMC-based bipolar HV pulse generator that reduces the system sensitivity, cost, and complexity. A detailed illustration of the proposed approach is presented in this paper. The simulation and experimental results are used to validate the proposed concept. [ABSTRACT FROM AUTHOR]

This paper proposes a six-phase surface-mounted permanent-magnet machine with a 24-slot/10-pole fractional slot winding, which not only eliminates the air-gap flux subharmonics, but also minimizes the effect of slot harmonics, which highly affect both the core and magnet losses. The six-phase winding design also offers an improved drive train availability for electric vehicle applications due to its inherent high fault-tolerant capability. When compared with a three-phase design, the proposed winding offers approximately 3.5% improvement in torque density, a significant reduction in both the core and magnet losses, and an improved overall efficiency. The proposed winding is deduced based on the stator shifting concept of two 12-slot/10-pole stators with single tooth windings. The coil span of the resulting machine will be two slots, which stands as a compromise between single tooth and distributed windings. The concept of stator shifting is first presented, and then, a prototype machine is designed and simulated using the 2-D finite-element analysis to validate the proposed concept. A comparative study is also carried out to compare six-phase and three-phase designs with the same slot/pole combination and also with the 18-slot/10-pole combination, which was recently shown to be a competitive alternative. [ABSTRACT FROM AUTHOR]

Voltage source converter (VSC)-based high voltage DC (HVDC) transmission is considered the future of offshore power transmission. This paper aims at providing a reliable VSC-HVDC transmission system architecture between offshore wind farms and onshore grids. In this paper, a large-capacity, low-speed flywheel energy storage system (FESS) based on a squirrel cage induction machine is applied in parallel with the VSC-HVDC at the grid side converter. The FESS is dedicated for surge power (due to power flow imbalance during fault) absorption instead of being dissipated in the form of resistive losses. Since the duration of these surges is relatively small, it has been shown that the flywheel can effectively mitigate this problem. In addition to the fault ride-through support during fault conditions, the FESS is employed for power leveling functionality during normal operation. The performance parameters of the proposed approach are investigated via both simulation and experimental results. A 132-kV, 100-MW HVDC system is simulated using MATLAB/Simulink during normal and fault conditions. The proposed architecture is substantiated experimentally through a scaled down test rig with a 2-kW FESS. [ABSTRACT FROM AUTHOR]

This paper presents the steady-state mathematical model of a five-phase induction machine with a combined star/pentagon connection. The connection splits the stator winding into two five-phase windings displaced in space by $\pi$/10 and connected in a combined star/pentagon configuration. Recent work limited to an experimental investigation demonstrated that the connection possesses improved fault tolerance when compared to a conventional star-connected stator, as well as avoids the pentagon connection problems. Although the machine has five-phase terminals, it is intrinsically an asymmetrical ten-phase machine, which introduces additional subspaces in the machine's mathematical model. In order to theoretically investigate and thoroughly assess this connection against conventional connections, this paper introduces the steady-state mathematical model based on vector space decomposition and symmetrical component theory. Finite-element analysis is first used to investigate the different harmonic current components induced in the cage rotor circuit, upon which the effect of different subspaces can be clarified and the required transformation matrix from phase variables to their sequence components can be derived. The model is verified using a 1-kW prototype five-phase induction machine. [ABSTRACT FROM PUBLISHER]

Converting existing ac transmission lines to an extended multiterminal three-wire bipolar HVDC system can be considered a cost-effective way to interconnect dispersed offshore wind farms to onshore ac grids instead of building new bipolar HVDC systems. To automatically coordinate between different converters in a multiterminal HVDC (MTDC) system, droop control techniques have been adopted as an effective means without the need for fast communications between units. The droop control design is mainly dependent on the line resistances. This paper shows that the equivalent resistance of a three-wire bipolar system changes based on the operational mode. The modification to droop control design of an MTDC equipped with a three-wire bipolar system is then presented to tackle this resistance variation with the operating condition. Two types of MTDC systems are considered in this work, namely, radial parallel and meshed parallel systems. Different simulation studies have been conducted to validate the results of the presented analysis. [ABSTRACT FROM PUBLISHER]

The interior permanent magnet (IPM) machine equipped with a fractional-slot concentrated winding (FSCW) has met an increasing interest in electric vehicle applications due to its higher power density and efficiency. Torque production is due to both PM and reluctance torques. However, one of the main challenges of FSCWs is their inability to produce a high-quality magnetomotive force (MMF) distribution, yielding undesirable rotor core and magnet eddy-current losses. Literature shows that the reduction of low-order space harmonics significantly reduces these loss components. Moreover, it has been previously shown that by employing a higher number of layers, although causing some reduction in the winding factor of the torque-producing MMF component, both machine saliency and reluctance torque components are improved. Recently, a dual three-phase winding connected in a star/delta connection has also shown promise to concurrently enhance machine torque of a surface-mounted PM machine while significantly reducing both rotor core and magnet losses. In this paper, a multilayer winding configuration and a dual three-phase winding connection are combined and applied to the well-known 12-slot/10-pole IPM machine with v-shaped magnets. The proposed winding layout is compared with a conventional double-layer winding, a dual three-phase double-layer winding, and a four-layer winding. The comparison is carried out using 2-D finite-element analysis. The comparison shows that the proposed winding layout, while providing similar output torque to a conventional double-layer three-phase winding, offers a significant reduction in core and magnet losses, correspondingly a higher efficiency, improves the machine saliency ratio, and maximizes the reluctance toque component. [ABSTRACT FROM AUTHOR]