Search

Most photovoltaic (PV) systems are composed of series and parallel inverters. The electromagnetic interference (EMI) mainly comes from the off–on of inverter switches with pulsewidth modulation (PWM). The output EMI peaks of PV systems would increase markedly due to the interference superposition effect caused by parallel inverters, whose carrier initial phases are in phase or close to each other. In this paper, an auto-screening carrier phase-shift scheme is proposed to weaken the superposition effect of EMI peaks and to get the result of reverse offset at its best. In a PV system, through voltage detections and spectrum estimations of each inverter with a series of phase-shift carriers, a best carrier phase of each inverter is obtained automatically to minimize EMI peaks of the PV system. In order to avoid the conflict that the screening processes of two or more inverters are underway at the same time, a specific frequency signal is output temporarily as an occupancy mark in one of the inverters. The feasibility and effectiveness of the proposed scheme are verified by experimental results in a PV system composed of four parallel single-phase inverters. [ABSTRACT FROM AUTHOR]

A discontinuous pulsewidth modulation (DPWM) strategy for three-level neutral-point-clamped (NPC) traction inverter drive for electric vehicles (EVs) with minimum switching loss for the full power factor (PF) range is developed and presented in this paper. Considering the dynamic loading conditions in an EV propelled by an induction motor (IM), the discontinuous modulation strategy is generalized to obtain minimum switching loss for a wide variations in load PF and modulation depth. The dynamic operating conditions in EV may render frequent unbalances in dc-link capacitor voltages in NPC inverter. It is demonstrated that the addition of an appropriate offset signal with the reference discontinuous signals generates compensating neutral current in the right direction, which can be used to mitigate existing unbalance in two dc-link capacitor voltages. Minimum switching loss at variable PF is attained by positioning the nonswitching clamped regions of the reference auxiliary signals according to the load PF. The effectiveness of the proposed scheme for a wide range of torque/speed variations is studied through simulation by developing a MATLAB/SIMULINK model of an IM traction inverter drive with field-oriented control strategy for closed loop control. Finally, the modulation scheme is validated through experimentation in a small-scale prototype NPC inverter with motor loads. [ABSTRACT FROM AUTHOR]

In this paper, in response to the open-circuit fault scenario in the grid-side converter (GSC) of doubly fed induction generator-based wind turbines (DFIG-WTs), a fault-tolerant four-switch three-phase (FSTP) topology-based GSC is studied. Compared with other switch-level fault-tolerant converter topologies, fewer switches, less switching and conduction losses, and simpler converter structure are derived. A simplified space vector pulse width modulation (SVPWM) technique is proposed to improve the output current quality and reduce the computational complexity in the control process. Unified expressions of duty ratios for the two remaining healthy bridge arms are obtained. In addition, the three-phase unbalance phenomenon caused by the capacitive impedance in the faulty phase is analyzed from the ac point of view, and a current distortion compensation scheme is illustrated. Furthermore, a dc-bus voltage deviation suppression strategy is proposed to maximize the dc-bus voltage utilization rate and mitigate the damage to the dc-link capacitors. Simulations are carried out in MATLAB/Simulink2017a to demonstrate the validity of the proposed SVPWM technique and compensation schemes in FSTP GSC for a 1.5-MW grid-connected DFIG-WT when different working conditions are considered. [ABSTRACT FROM AUTHOR]

Torque ripple caused by zero-sequence current (ZSC) and relatively high switching frequency severely worsens the operating performance of an open-winding permanent-magnet synchronous machine (OW-PMSM) system with common dc bus. In this paper, a novel q-axis current injection method based on the angle-shift-based voltage distribution is proposed for the OW-PMSM system with common dc bus. With the proposed method, torque ripple caused by ZSC can be counteracted by the torque component generated by the injected q-axis current. Meanwhile, the corresponding modulation range is analyzed to investigate the availability of the proposed method. Moreover, in order to reduce the switching frequency, zero vector (111) is no longer necessary to compensate the zero-sequence component and conventional space vector pulsewidth modulation (PWM) with zero vectors (000) and (111) can be simplified. The switching actions in one PWM period can be reduced from 12 to 8. The comparison of losses shows that this strategy can effectively improve the efficiency under both heavy load and high switching frequencies. Finally, the effectiveness of the proposed method is validated through an OW-PMSM experiment with common dc bus. [ABSTRACT FROM AUTHOR]

In this paper, a new method is applied to predict the average value of the phase currents of a two-level voltage source converter. The method uses a suitable model of the converter, the modulation method, and the measurement. The samples given by the analog-to-digital converter (ADC) are used to predict the time progress of the currents in every switching cycle and then calculate its average. This allows removal of the delay introduced by filtering and avoids aliasing in the measurements. The average prediction is contrasted with the pulsewidth modulation (PWM) synchronous sampling method and the sigma-delta ADC with a moving average filter. Applied to a load observer, the method effectively reduces its estimation error. The findings are verified experimentally. [ABSTRACT FROM AUTHOR]

In this paper, a novel space-vector pulsewidth modulation technique for a five-level active neutral-point clamped (5L-ANPC) inverter is proposed to eliminate the common-mode voltage (CMV). For the 5L-ANPC inverter, which produces a good output voltage performance and lowdv/dt, the total 125 voltage vectors can be generated, among which the proposed scheme employs only 19 voltage vectors producing a zero CMV. Due to the limitation of voltage vectors selected, the dc-link capacitor voltages of the 5L-ANPC inverter cannot be balanced by themselves. Therefore, the capacitor voltages of the inverter should be controlled by choosing the redundant switching states appropriately. The validity of the proposed modulation scheme has been verified by simulation and experimental results. [ABSTRACT FROM AUTHOR]

High step-down voltage conversion is necessary to bridge the voltage gap between main power converters and low-voltage auxiliary electronics in power conversion systems. Switched capacitor converters (SCCs) are an attractive candidate as a high step-down converter, but their poor voltage regulation capability may limit their applications. Pulsewidth modulation (PWM) SCCs with adjustable high step-down voltage conversion are proposed in this paper. The proposed PWM SCCs can be derived from traditional SCCs by replacing an energy transfer capacitor with a switched-capacitor-inductor (SCL) cell that comprises inductors, capacitors, and diodes to realize PWM-controllable voltage conversion. The voltage step-down ratio of the proposed PWM SCCs is not only PWM controllable but also adjustable with structures of SCCs and SCL cells. Two representative PWM SCCs were taken as examples to perform the operational analysis. The prototypes of both representative PWM SCCs were built and tested to demonstrate the proposed concept. [ABSTRACT FROM AUTHOR]

Common-mode voltage (CMV) is known as a major cause of premature motor failures. The form and amplitude of the CMV generated by any converter depends on both the circuit topology and modulation technique. Among single stage ac–ac converters employed in drive applications, the Z-source ultra sparse matrix converter (ZSUSMC) is a desirable choice due to reduced number of switches in its structure and voltage boosting capability. Based on these considerations, this paper aims to: 1) theoretically determine and compare the CMV of the ZSUSMC with four well-known impedance networks, namely, cascaded, switched-inductor, quasi, and series, in its structure and 2) propose modulation techniques for CMV reduction in the ZSUSMCs. To this end, first, it is shown that the ZSUSMC, depending on the impedance network used in its structure, provides more freedom to choose from redundant switching states compared to the ultra sparse matrix converter. Then, by taking advantage of this feature, novel modulation strategies that attenuate the CMV without affecting the boosting capability are developed. The proposed modulation schemes are based on avoiding the switching states most contributing to the CMV during a switching period. Through hardware-in-the-loop studies, the effectiveness of the proposed modulation strategies in reducing the CMV of the ZSUSMCs is verified. [ABSTRACT FROM AUTHOR]

In voltage-source inverters (VSIs), dead time is used to prevent shoot-through over switching devices. However, the existence of the dead time will distort the output phase current, which degrades the performance of the inverter as well as influences the common-mode voltage (CMV), particularly in CMV elimination relevant modulation schemes, such as zero-common-mode (CM) pulsewidth modulation (PWM)-based paralleled inverters. In the light of the situation that the normal sampling-based dead-time compensation (DTC) methods are often disturbed by the current ripple, this paper introduces a novel DTC method for the VSI, which can mitigate the impact of the current ripple and improve the accuracy of DTC. The proposed method deduces the real-time current ripple, which can reconstruct the actual trajectory of phase-leg currents, and the peak values corresponding to rising and falling edges for PWM signals can be predicted. In this way, DTC can be implemented based on the direction of relevant instantaneous switching currents and finally improves the accuracy. Especially, the current-ripple-prediction-based DTC can help to improve the CMV distortion caused by the dead time for paralleled inverters with zero-CM PWM. Simulation and experimental results are provided to validate that the proposed method can be applied to different topologies and modulation schemes with good performance. [ABSTRACT FROM AUTHOR]

A new class of impedance networks is proposed in this paper. The proposed coupled-inductors-based impedance cells, called the series and the tapped switched-coupled-inductors, are employed within the (quasi) switched boost networks. The achieved impedance networks based on the proposed cells offer very high conversion gains with less-than-unity turn ratios (n < 1), which simplifies the realization of the magnetic element and at the same time reduces the number and size of passive components. The high boosting capability is achieved with small shoot-through durations that bring some additional advantages, such as low ratings of switching devices. The circuit analysis and operation concepts as well as a design procedure for the components of the proposed impedance networks are presented. Theoretical achievements are confirmed through experiments on a 220 W dc–dc converter laboratory setup. [ABSTRACT FROM AUTHOR]

This paper proposes a transformerless line-interactive uninterruptible power supply (UPS) with low ground leakage current. A high-efficiency bidirectional inverter is suggested, which performs the line-interactive UPS functions with low ground leakage current. It has a full-bridge inverter and a bidirectional switch, which operate with the unipolar pulsewidth modulation. Because the bidirectional switch operates at the line-frequency, switching losses can be lower than the previous transformerless inverters. As the inverter operates, the parasitic capacitance between the inverter and the ac voltage ground is clamped to zero voltage for a positive line cycle and to the ac voltage for a negative line cycle, respectively. Thus, the parasitic capacitance can be prevented from being charged or discharged, which ensures the absence of the ground leakage current. The operation modes of the proposed system are described. The control schemes are presented to design the proposed inverter for the line-interactive UPS. Experimental results for a 2.0 kW prototype are discussed to verify the performance of the proposed system. [ABSTRACT FROM AUTHOR]

This paper proposes the new clamping angle control (CAC) pulse width modulation (PWM) method to restore its maximum linear modulation range of voltage source inverters (VSIs) reduced by the duty ratio limitation in hardware implementation, which makes the VSIs to operate nonlinearly in the high modulation range. The deadtime and the bootstrap gate driver circuit mainly cause this duty ratio limitation in practice. In particular, the bootstrap gate driver circuit is used in many industrial applications by avoiding the additional power supply to apply the gate-source voltage of power switches, and therefore making the VSIs to be small size with the low cost. First, the proposed CACPWM method is theoretically analyzed. Then, it is applied in the high modulation range to overcome the limitation of the duty ratio due to the use of the bootstrap gate driver circuit. Thereafter, its practical effectiveness is verified by both simulation and experimental tests. Also, the resulting harmonic distortions are compared with those by the conventional PWM methods. [ABSTRACT FROM AUTHOR]

In this paper, a novel direct ac–ac converter based on the coupled inductor Z-source networks is proposed that offers a wide range of buck–boost operation. A total of two Z-source networks, called the coupled switched inductor and the modified switched coupled inductor, are employed that enable the ac–ac converter to deliver a wide voltage range. The proposed converter with both networks provides free-wheeling current paths for the inductors currents during the state transitions, which results in solving the commutation problems and the need for snubber circuits. A simple switching strategy is then proposed that helps to share a common magnetic core between the coupled inductors. For any particular voltage gain, the proposed structures require a smaller duty cycle compared to the conventional ones; therefore, a smaller inductance is required. Simulation and experimental results are provided to confirm the theoretical achievements. [ABSTRACT FROM AUTHOR]

This paper analyzes the accuracy of the zero-order hold (ZOH) model for the digital pulse width modulator (DPWM) in the s-domain. The s-domain model and the exact z-domain model for the current control of a single-phase inverter with an L-type filter are elaborated for quantifying the deviation of the ZOH model for the DPWM. The influences of the different computational delay and duty-cycle update modes on this deviation is analyzed in detail. The compensation method for this deviation of the ZOH model is proposed for accurately predicting the stability region of the control system in the s-domain. Simulations and experimental tests are executed to verify the effectiveness and correctness of the theoretical analysis. [ABSTRACT FROM AUTHOR]

An adaptive control of DPWM implementable in clamped-three-level inverters with two strings of photovoltaic (PV) panels in cascaded connection is proposed in this paper. The proposed modulation is developed based on the so-called circuit-level decoupling concept. It is able to provide balance line voltage even under unbalanced dc links. The unequal dc voltages appeared due to asymmetric maximum point of power trackings (MPPTs) are controlled by proper injection of zero-sequence voltage to the common mode voltage, while the total dc voltage is regulated based on the voltage commands generated by the MPPT of each string. Thus, both PV strings are able to be operated based on their MPPTs while there is almost no low-order harmonic distortion at the inverter output current. Compared with the previous methods, the high capability of the proposed method is evaluated by simulation study and experimental tests. [ABSTRACT FROM AUTHOR]

This paper presents an improved analytical model for estimating the high-frequency current ripple of interior permanent magnet synchronous machines due to pulsewidth modulation (PWM) switching. The proposed model accounts for the impact of slotting effect, magnetic saturation, and cross-coupling between the $d$ - and $q$ -axis. The model is subsequently used to investigate several factors that influence the PWM-induced current ripple. These include the PWM switching frequency, fundamental frequency (i.e., machine speed), dc-bus voltage, current control angle (i.e., γ angle), and the excitation current amplitude (i.e., saturation level). Experiments have been conducted to verify the analytical prediction results. These results show that the analytical model can predict the PWM-induced current ripple waveshape very well for many operating conditions and accurately estimate its rms value over a complete fundamental period. [ABSTRACT FROM AUTHOR]

Recent power systems, such as renewable energy systems consisting of solar panels and rechargeable batteries, contain multiple power sources and need multiple converters in proportion to the number of power sources, resulting in increased system complexity and cost. This paper proposes a multiport converter (MPC) integrating a bidirectional PWM converter and series-resonant converter. Not only is the switch count halved with the proposed MPC, but also magnetic components can be integrated, reducing the circuit complexity and volume. A 150-W prototype of the proposed MPC was built for the experimental verification. The measured voltage conversion characteristics and transient responses demonstrated that the proposed MPC could control load and battery voltages independently by pulse width modulation and pulse frequency modulation controls, respectively. [ABSTRACT FROM AUTHOR]

A sawtooth carrier-based sinusoidal pulse width modulation (SC-SPWM) technique for asymmetrical six-phase two-level inverters is proposed in this paper, which could reduce both the peak-to-peak amplitude and the changing frequency of the common-mode voltage (CMV). The intersection-plotting method reveals that the mirror symmetrical sawtooth carriers for two three-phase groups can help optimize the distribution of overlapping areas, which is the CMV reduction mechanism of SC-SPWM. Additionally, the Fourier analysis is employed to quantitatively evaluate the modulation index and harmonic performance of SC-SPWM compared with the conventional SPWM and two phase-shifted SPWM methods. Also, further analysis demonstrates that dead time does not affect the reduction of CMV in a noticeable way. Finally, both simulation and experimental results coincide with the theoretical analysis that the proposed SC-SPWM shows the best performance in reducing the CMV amplitude and changing frequency among these four SPWM methods, though it leads to a higher phase current distortion. [ABSTRACT FROM AUTHOR]

In this paper, a three-level quasi-switched boost T-type inverter (3L qSBT2I) is proposed. A new pulse-width modulated (PWM) control method is presented to reduce the inductor current ripple of the qSBT2 I. In the introduced PWM technique, the shoot-through duty cycle is maintained constant to keep the modulation index as high as possible. Then, the only control parameters of the qSBT2I are the duty cycles of the two additional switches. By controlling the duty cycles of the two additional switches, the voltage gain of the proposed qSBT2 I can be improved to a value larger than that of the conventional 3L impedance source inverters. The steady-state analysis, operating principles, and comparisons with the impedance source-based 3L inverters are presented. A 1-kW prototype is constructed to verify the operating principle of the 3L qSBT2I. An indirect dc-link voltage regulator and a capacitor voltage-balance controller are applied to the proposed qSBT2I. Simulation and experimental results are presented. [ABSTRACT FROM AUTHOR]

This paper has focused on the novel space vector pulse-width modulation (SVPWM) strategy for the two-level three-phase inverter, which could eliminate the harmonics nearby pulse width modulation (PWM) frequency. Ear-piercing high-frequency electromagnetic noise from motor is common due to PWM technique. The proposed SVPWM is able to remove the high-frequency harmonics located nearby the PWM frequency and other odd multiples by changing the original switching states. The unpleasant acoustic noise could be removed with the novel strategy whose PWM frequency is selected near 10 kHz. By comparison, it is near 20 kHz for conventional SVPWM to achieve the similar performance. Therefore, the switching losses are significantly reduced using the novel method. Furthermore, the proposed technique neither changes the characteristics of the fundamental wave nor employs the additional circuits in the drive. At last, the effectiveness of proposed strategy is verified by simulation and experiment. [ABSTRACT FROM AUTHOR]

In order to incorporate the advantage of the $V^{2}$ control scheme and the benefits of digital implementation, this paper proposes a digital $V^{2}$ control with hybrid capacitor current ramp compensation, which includes the estimated output capacitor current ramp and the external ramp. Since capacitor current responds to the load change immediately, the proposed method has faster transient response than either digital inductor current compensation or external ramp compensation. The proposed estimator does not require high sampling rate and avoids the current ramp distortion due to the parasitic resistance and inductance. The small-signal model is derived by describing function to understand the dynamic characteristics of the proposed control scheme. The model provides design criteria of the current feedback gain and the external ramp slope. The effectiveness of the proposed control architecture and the current ramp estimator is verified by simulation and experimental results. Compared with the benchmark, the proposed control has 70% reduction on settling time and 20% reduction on undershoot deviation. [ABSTRACT FROM AUTHOR]

This paper investigates an ac–dc–ac multilevel power converter. The studied configuration is composed of two single-phase ac–dc–ac three-leg modules and series-connected H-bridges in the shared part of system. Because the proposed converter has shared legs between the input and output, it is employed in applications with same input and output frequency. Uninterrupted power supply and unified power quality conditioner are application examples for this converter. Such multilevel topology has lower dc-link voltage rating, which, consequently, presents low switch blocking voltages when compared to conventional topologies. System model, a space-vector pulsewidth modulation (PWM) strategy to symmetrical and asymmetrical dc-link voltages, and an overall control strategy to adjust the system variables are presented. A power flux analysis shows the operation zone in which the individual dc-link voltage balancing is possible. PWM and control strategies are developed to reduce the semiconductor total losses, harmonic distortion, and switching stress. Two ac–dc–ac multilevel conventional structures are used for comparison. Simulation and experimental results demonstrate the feasibility of the studied converter. [ABSTRACT FROM AUTHOR]

This paper investigates a multilevel inverter composed of series/parallel-connected H-bridges. The presented structure can be used for applications in which the use of semiconductor switches with low-voltage and low-current ratings is intended. A comprehensive system model, an overall control strategy to adjust the output voltage with constant magnitude and frequency, and a level-shifted PWM (LS-PWM) strategy based on a voltage vectors unidimensional analysis and a plane analysis are presented. The LS-PWM is capable of mitigating the low-frequency circulating current, thus generating multilevel voltage signals with low harmonic distortion, maximum number of levels, and low dv/dt. In addition, considering a wide range of values of voltages and currents and various power levels, the total converter losses are reduced compared with the conventional multilevel converters. Two multilevel conventional inverters with the same number of semiconductor switches are used for comparison. Simulation and experimental results demonstrate the feasibility of the studied converter. [ABSTRACT FROM AUTHOR]

This paper presents a nine-level transformer-based inverter requiring only eight switches. The envisaged structure consists of two standard H-bridges fed from a single dc source. Besides, a single-phase transformer is employed to aid the process of intermediate voltage level generation. An ad-hoc pulsewidth modulation scheme based on boolean logic form equations is developed to derive the gating pulses. An effortless extension of the proposed inverter to a higher number of voltage levels is also achieved by generalizing the switching functions. Furthermore, the superior performance of the proposed topology is demonstrated through a comprehensive cost-based analysis. Finally, the validation of the proposed topology is accomplished through experiments on a down-scale prototype, and the measurement results are included. [ABSTRACT FROM AUTHOR]

An optimal current control strategy for asymmetrical hybrid multilevel inverters (MLIs) is proposed in this paper enabling their use on motor drives, static synchronous compensators, and photovoltaic and wind generators, where a fast and precise current regulation is required. A key feature of these highly efficient converters is that an ac machine (motor or transformer) operates according to an open-end winding configuration, connected on one side to a main MLI and, on the other side, to an auxiliary two-level inverter (TLI). The first efficiently controls the main power stream operating at a low switching frequency, while the TLI acts as an active power filter, exploiting a conventional high-frequency two-level pulsewidth modulation (PWM) technique. The proposed control scheme optimally exploits the key features of the two inverters by suitably sharing the control task. In fact, a predictive current control is assigned to the MLI, which can be accomplished by low switching frequency operations, while the high switching frequency of the PWM-operated TLI is exploited to accomplish a fast and precise closed-loop current control, processing only a part of the power stream flowing through the system, thus producing low power losses. Simulations and experimental results confirm the consistency of the proposed approach. [ABSTRACT FROM AUTHOR]

This paper illustrates the application of a solving method of linear systems to a multilevel inverter. This study applies a generic pulsewidth modulation (PWM) method to a multilevel topology. This method finally highlights some specific modulation schemes. First, the study describes the mathematical model of the inverter leg. The leg is made of three level T-type structure. The model is extended to the three-phase inverter. The generalized inverse is used to generate the solution set of the conduction rates. Among the modulation strategies possible, three specific modulation schemes are proposed. The modulation schemes are applied to simulate a PWM three-phase inverter. Finally, some experimental results complete the analysis. [ABSTRACT FROM AUTHOR]

In order to prevent the power switching devices (e.g., an insulated-gate bipolar transistor, IGBT) from shoot-through in voltage-source converters during a switching period, the dead time is added either in the hardware driver circuits of the IGBTs or implemented in software in pulse width modulation (PWM) schemes. Both solutions will contribute to a degradation of the injected current quality. As a consequence, the harmonics induced by the dead time (referred to as “dead-time harmonics” hereafter) have to be compensated in order to achieve a satisfactory current quality, as required by standards. In this paper, the emission mechanism of dead-time harmonics in single-phase PWM inverters is, thus, presented considering the modulation schemes in detail. More importantly, a repetitive controller has been adopted to eliminate the dead-time effect in single-phase grid-connected PWM converters. The repetitive controller has been plugged into a proportional-resonant-based fundamental-frequency current controller so as to mitigate the dead-time harmonics and also to maintain the control of the fundamental-frequency grid current in terms of dynamics. Simulations and experiments are provided, which confirm that the repetitive controller can effectively compensate the dead-time harmonics and other low-order distortions, and also, it is a simple method without hardware modifications. [ABSTRACT FROM AUTHOR]

Stand-alone microhydro systems based on the self-exited induction generator (SEIG) are popular in developing countries. However, an electronic based controller is required to maintain the quality (voltage and frequency) of the generated power within an acceptable range. Conventionally, this controller is designed using a phase-controlled thyristor circuit (or more recently using a dc chopper circuit) and a fixed resistance dump load to receive the excess generated power. Generally, in small communities the total dissipated power in the dump load is greater than the consumed power by all the households. This problem of inefficient power usage can be solved by distributing the controller among households. The objective of this paper is to improve the distributed electronic load controller (DELC). As with the original DELC, the proposed improved DELC is used for two purposes: First, consuming the excess generated power individually by each household; and second, operating as a complementary device for voltage and frequency regulation of the SEIG. The detailed design and experimental verifications of the proposed improved DELC including the design of an appropriate input filter to minimize the network current distortion are presented here. Additionally, MATLAB simulations are used to study the interaction between the proposed improved DELC and the powerhouse controller (the ELC). [ABSTRACT FROM AUTHOR]

Application of pulse width modulation (PWM) is known to produce sideband effects. The accuracy of the models of dc–dc converters can be improved if essential information of the sideband effects of PWM can be incorporated. In this paper, the aliasing effect of the sideband components on the closed-loop control is analyzed, and an effective representation of the transfer function of the pulse-width modulator is derived. Applying this transfer function to the dc–dc converter, an extended-frequency-range small-signal model is obtained, which can be conveniently used for deriving the loop gain of a PWM-controlled dc–dc converter. Furthermore, for wideband control applications, the large switching ripple in the modulation signal necessitates adjustment of the representation of the gain of the pulse-width modulator, which is dependent on the controller. Despite being highly accurate for stability assessment, the extended-frequency-range model is relatively complex after incorporating the effects of the sideband components and the large switching ripple. An approximate approach is introduced to simplify the loop gain expression and to provide physical insights into the effects of the sideband components and large modulation ripple amplitude. Experimental verification of the extended-frequency-range model is provided for a buck converter and a boost converter. [ABSTRACT FROM AUTHOR]

In this paper, a new single-stage half-bridge (HB) resonant $LLC$ converter additionally employing one resonant capacitor and two relays with one package is proposed, compared with a single-stage HB $LLC$ converter. Moreover, a center-tapped transformer is replaced with a coupled transformer. Since the proposed converter changes the turns ratio of the coupled transformer using a relay according to low- or high-input-voltage range, it can decrease the range of its needed voltage gain. It means that the proposed converter can be designed with large transformer magnetizing inductance compared with the conventional single-stage HB $LLC$ converter. As a result, the primary conduction and turn-off losses are reduced. Moreover, in low input voltage range, it has smaller total primary wire resistance of the transformer due to parallel connection of the coupled transformer, which decreases its conduction loss. In addition, additionally employed small-sized components can be inserted to the conventional system. To confirm the operation, features, and validity of the proposed converter, universal input with low line and high line and 16.5 V/60 W output laboratory prototype targeting laptop adapters with wide-input-voltage range is built and tested. [ABSTRACT FROM AUTHOR]

This paper proposes a zero-sequence circulating current (ZSCC) control scheme for the multiparalleled three-level T-type inverters (3LT2Is). Based on the analysis with the proposed generalized model of multiparalleled 3LT2Is, it is seen that the ZSCC is influenced by the circuit parameters, duty cycles, and the circulating currents of the l th and first 3LT2I. To mitigate the circulating currents, a deadbeat control strategy for n-paralleled (n≥3) inverters is proposed, which is realized by adjusting the duty cycle of the small vectors in each PWM sampling period. Compared with the conventional PI control method, the ZSCC spike is mitigated with the proposed scheme, thus improving the quality of the output currents. Also, the reliability of the 3LT2Is system is improved because such a scheme only needs the information about the ZSCC and zero-sequence duty ratio in the l th and the first inverter. The proposed method can also be applied to the neutral-point-clamped converters. Simulation and experimental results verify the effectiveness of the theoretical analysis and the proposed method. [ABSTRACT FROM PUBLISHER]

The switching frequency is an important control parameter of pulse-width-modulation (PWM) rectifier to reduce switching losses and electromagnetic interference noise. This paper proposed a variable switching frequency PWM (VSFPWM) strategy for dc-link voltage ripple control in two-level rectifier. DC-link voltage ripple is determined by the dc-link current directly, and can be predicted synchronously with PWM signals. A real-time prediction model of dc-link voltage ripple is derived for a common voltage-oriented control PWM rectifier. Then, VSFPWM control is introduced, which changes the switching frequency cycle to cycle with a restriction of dc-link voltage ripple peak value. Furthermore, the dynamic behavior is also observed when the proposed VSFPWM control scheme is adopted. Detail simulation and experimental comparisons are carried out between VSFPWM and normal constant switching frequency PWM, which demonstrate the advantages of the proposed method. [ABSTRACT FROM AUTHOR]

This paper presents the analysis of low leakage inductance current regions, small-signal model, and decoupled control for a dual-half-bridge isolated bidirectional dc–dc converter with pulse width modulation plus phase-shift strategy. Traditionally, the duty cycle of the transistors is fixed at 0.5 and only the phase-shift is varied to regulate the output voltage. With PPS control, two control freedoms—the duty cycle is used to regulate the voltage gain and phase-shift is used to control the power flow—can be obtained to expand input-voltage variation range. In addition, since the amplitude of leakage inductance current is limited, the current stresses of transistors can be reduced. According to the analysis, there exists a region in which higher leakage inductance current leads to lower output power and thus, causes more conduction loss. Attention should be paid to avoid this operation region. Then, a small-signal model is derived in the low conduction loss region with the state space averaging method to facilitate the closed-loop design. In addition, a decoupled control strategy is proposed to eliminate the interactions between phase-shift ratio and duty cycle, so as to simplify the proportional-integral controller design significantly. A prototype was built to verify the theoretical analysis. [ABSTRACT FROM AUTHOR]

This paper presents the active capacitor voltage-balancing (ACVB) methods based on the dynamic model for a five-level nested neutral-point piloted (NNPP) converter using hybrid carrier modulation. The traditional hybrid carrier modulation provides natural voltage balancing of floating capacitors and dc-link capacitors. First, the natural voltage-balancing ability under steady-state and ideal conditions is theoretically proved. However, there are accumulated errors and deviations of capacitor voltages in practical applications, especially under dynamic conditions. In order to address the accumulated errors and deviations of capacitor voltages, the dynamic models of floating-capacitor voltages and neutral-point voltage are established. Moreover, the ACVB method based on the dynamic model of the neutral-point voltage is proposed by injecting the zero-sequence voltage. And the ACVB method based on the dynamic model of floating-capacitor voltages is proposed by introducing the adjustment variables. The proposed ACVB methods have the advantages of simple formula, definite physical meaning, and high accuracy. Furthermore, the output voltage quality and current quality are evaluated in term of total harmonic distortion and the effect of model parameter mismatch on the proposed ACVB methods is presented. Finally, the comparative simulation and experimental results verify the correctness of the proposed ACVB methods based on the dynamic model under different conditions. [ABSTRACT FROM AUTHOR]

For dc–dc converters with pulsating output current, such as boost and buck–boost converters, the use of leading-edge or trailing-edge pulse width modulation (PWM) can result in distinctly different behavior. This phenomenon is not readily captured by the usual averaged model but can be predicted with a discrete-time model. However, the discrete-time model, which tracks the dynamics of state variables over a switching period, is usually more complex and less convenient to apply for the design of the feedback control. Based on the low-pass characteristics of dc–dc converters, an approximate discrete-time model is proposed in this paper, and upon transforming to the s-domain, the model results in transfer functions that can be conveniently used for deriving practical closed-loop parameters. With the proposed model, the loop gain, the input and output impedances are derived and analyzed. The effects of applying different types of PWM on the stability of a single dc–dc converter and a system of cascaded dc–dc converters are discussed. Finally, prototypes of a buck converter, a boost converter, and a cascaded system of buck and boost converters are constructed to verify the effectiveness of the approximate discrete-time model. [ABSTRACT FROM AUTHOR]

This paper presents a hybrid pulse width modulation-based discontinuous modulation (D-HPWM) strategy with dc-link voltage balancing for a three-level neutral-point-clamped (NPC) traction inverter drive. The results are then compared with continuous-hybrid-PWM (C-HPWM) to check the performance improvement. The HPWM strategy uses both the advantages of carrier- and space-vector-based PWM strategies. The duty cycles are generated using the carrier-based strategy to reduce the computational time and complexity of the system and redundant vector states are used to keep the two dc-link capacitor voltages balanced. As discontinuous PWM (DPWM) reduces the switching losses considerably compared to the continuous PWM, the DPWM strategy is developed in this paper for the HPWM-based strategy. Detailed comparison studies are then carried out in MATLAB/Simulink and PLECS to show the conduction and switching loss distribution with change in modulation index for different power switches. A 54.0-kW surface permanent magnet synchronous machine (PMSM) is used for this simulation studies. Moreover, the total inverter loss and losses in each insulated gate bipolar transistor (IGBT) are also compared. Detailed experimental performance analysis is also carried out with a scaled down prototype of a 6.0-kW surface PMSM, NPC inverter, and real-time emulator DSpace, to show the capacitor voltage deviation with both control strategies. [ABSTRACT FROM PUBLISHER]

This paper characterizes the sampling effect in digital sinusoidal pulse width modulation (SPWM) of voltage source inverter (VSI). The time-domain analysis presented in this paper establishes the relation between the fundamental frequency, carrier frequency, and the sampling frequency at different modulation indices of the SPWM. The analysis investigates the effect of sampling frequency of the digital controller on the output of the VSI. It is shown that the low-frequency harmonic components appear in the frequency spectrum of the VSI output voltage due to sampling. As a result, the output current of digitally controlled VSI is stepped in nature. The double Fourier integral solution of the switched waveform for inner and outer integral limits has been used to derive the expression. The integral solution is obtained using Jacobi-Anger expansions. The generalized results developed in this paper are useful to investigate the sampling effect in high switching frequency DSPWM. The proposed sampling effect has been analyzed for SPWM of single-phase H-bridge inverter. The analytical results are verified using simulation and experimental results. The experimental results have been obtained with the use of field-programmable gate array (FPGA) as a digital controller. [ABSTRACT FROM PUBLISHER]

A new pulsewidth modulation (PWM) strategy which is an alternative approach of the discontinuous PWM (DPWM) for a three-level neutral-point-clamped (NPC) inverter is proposed in this paper. A three-level NPC inverter is completely mature and very well-established topology in high-power applications. However, the three-level NPC inverter has an inheritance problem of the neutral-point voltage unbalancing due to the split dc-link capacitors. This structure can cause large neutral-point voltage ripple. Furthermore, output currents of the three-level NPC inverter are distorted by the neutral-point voltage ripple. Therefore, the neutral-point voltage must be controlled. In this paper, a new DPWM method using two different offsets for the neutral-point ripple reduction is proposed and the effectiveness of the proposed DPWM method is verified by using the simulation and the experimental results. [ABSTRACT FROM PUBLISHER]

This paper presents a topology of a single-phase floating full-bridge three-level pulse width modulation (PWM) power inverter suitable for high-voltage/high-power dc–ac conversion. High power efficiency is obtained thanks to the slow (50/60 Hz) biasing of the H-bridge power supply terminals, allowed by a particular arrangement and control of two complementary active neutral point clamped voltage-source converters. As result, the main PWM switching voltage as well as the maximum drain–source voltage $V_{{\rm DSS}} of related transistors are reduced to one-half of the input VDD voltage. This is allowed by the internally generated and accurately balanced middle-node voltage VDD/2. Consequently, advantageous $r_{{\rm DS}({\rm on})}$ of the low-voltage transistors, along with reduced switching PWM voltage result in considerable decreasing of power losses in whole output power range. This paper introduces the main concept of the floating H-bridge topology, and presents in detail the circuit realization. The performances are demonstrated on $450 V_{{\rm DC}}/230 V_{{\rm AC}}$ 2 kW power inverter exhibiting 98.6% peak efficiency and realized in very small $100\times 60\times 30$ mm3 volume. [ABSTRACT FROM AUTHOR]

A conventional asymmetrical half-bridge (AHB) converter is widely used for dc–dc stage in low-to-medium power system. However, since the asymmetric operation of AHB converter causes the low efficiency over entire load condition, the conventional AHB converter is not usually considered for the candidate of server power system. In order to overcome the problems of the conventional AHB converter, a wide zero-voltage-switching (ZVS) range AHB converter with a clamp switch and a clamp diode is proposed in this paper. The proposed AHB converter (PAHBC) replaces a low-side clamp diode with a MOSFET switch and adds an auxiliary winding, which changes the transformer turns-ratio. From these modifications and the pulsewidth-modulation (PWM) control of clamp switch, the PAHBC can be designed optimally at nominal input condition and obtains additional dc gain at hold-up time condition. These advantages achieve the high conversion efficiency over the entire load condition. The operational principle and analysis of the PAHBC are presented in this paper and verified by a 340–400 V input and 50 V/500 W output laboratory prototype. [ABSTRACT FROM PUBLISHER]

Modulation schemes can significantly change the performance of a converter in the steady state. They have, thus, been extensively studied, but directed more at three-phase topologies, where triplen offsets are added. Single-phase systems, including ac–dc–ac, are less widely pursued, even though various topologies have since been proposed. The intention of this paper is, thus, to study two promising single-phase ac–dc–ac converters using reduced number of switches, and subsequently proposes modulation schemes for them. The proposed schemes help the converters to achieve better thermal spread among their switches, while keeping their dc-link voltages low. Single points of failure are thus minimized, allowing the converters to have longer lifetimes. Simulation and experimental results have demonstrated the intended performances, hence verifying the analyses presented in this paper. [ABSTRACT FROM PUBLISHER]

A low-order harmonic pulsating torque is a major concern in high-power drives, high-speed drives, and motor drives operating in an overmodulation region. This paper attempts to minimize the low-order harmonic torques in induction motor drives, operated at a low pulse number (i.e., a low ratio of switching frequency to fundamental frequency), through a frequency- domain (FD) approach as well as a synchronous reference frame (SRF) based approach. This paper first investigates FD-based approximate elimination of harmonic torque as suggested by classical works. This is then extended into a procedure for minimization of low-order pulsating torque components in the FD, which is independent of machine parameters and mechanical load. Furthermore, an SRF-based optimal pulsewidth modulation (PWM) method is proposed to minimize the low-order harmonic torques, considering the motor parameters and load torque. The two optimal methods are evaluated and compared with sine-triangle (ST) PWM and selective harmonic elimination (SHE) PWM through simulations and experimental studies on a 3.7-kW induction motor drive. The SRF-based optimal PWM results in marginally better performance than the FD-based one. However, the selection of optimal switching angle for any modulation index $(M)$ takes much longer in case of SRF than in case of the FD-based approach. The FD-based optimal solutions can be used as good starting solutions and/or to reasonably restrict the search space for optimal solutions in the SRF-based approach. Both of the FD-based and SRF-based optimal PWM methods reduce the low-order pulsating torque significantly, compared to ST PWM and SHE PWM, as shown by the simulation and experimental results. [ABSTRACT FROM AUTHOR]

This paper proposes a new bidirectional three-phase push–pull converter that has a simple structure and achieves zero-voltage switching turn-on of switches. Also, due to use of a single inductor, an imbalance among phase currents on the low-voltage high-current side is trivial in the proposed converter although no current sharing control is employed. In this paper, a new dual asymmetrical pulse width modulation (PWM) switching method is proposed for bidirectional power flow control with seamless mode change. The proposed switching method offers reduced circulating current and makes the converter easier to implement compared to the PWM plus phase shift-based control method since it is a general PWM method having two independent duty cycle controls on each side. Experimental results from a 3-kW prototype are provided to validate the proposed concept. [ABSTRACT FROM PUBLISHER]

In this paper, a single-stage solution for solar photovoltaic (PV) pumping system using a dual-inverter fed open-end winding induction motor drive is presented. The three-level dual-inverter requires a low PV bus voltage compared with its conventional three-level counterpart. This could avoid large string of PV modules and helps in reducing the voltage rating of the capacitors and semiconductor devices used in the system. This may further help in reduction of cost of the system. The proposed single-stage system is operated using an integrated control algorithm, which includes the maximum power point tracking (MPPT), the $V/f$ control, and the sample-averaged zero-sequence elimination (SAZE) pulsewidth modulation (PWM) technique. While the MPPT algorithm ensures the extraction of maximum power from the PV source, the $V/f$ control improves the motor pump performance. Furthermore, the zero-sequence current is avoided by the SAZE PWM algorithm. Thus, the integrated control algorithm improves the overall performance of the system. Furthermore, this paper also presents the details of system design and analysis of its dynamic behavior during transient environmental conditions. The performance of the system is verified using MATLAB simulation and hardware prototype. [ABSTRACT FROM PUBLISHER]

This paper presents an improved dc-link voltage balancing algorithm for a three-level neutral-point-clamped inverter by considering phase current direction. Detailed studies on the effects of change in load current direction on the dc-link capacitor voltages are presented. A maximum value of power factor is numerically derived, above which it affects the capacitor voltage balancing capability. Compared with the previously presented research work, the inputs to the space-vector pulsewidth-modulation block are the three phase currents and the difference between the two capacitor voltages. Depending on the states of the two dc-link capacitor voltages and phase current direction, redundant voltage vector sequences are selected. The selected vectors keep the capacitor voltage deviations within 5% of the total dc-link voltage. Two zero switching vectors (i.e., PPP and NNN) are also removed from all subsectors of the earlier proposed strategy, which one used to produce higher common-mode voltages. Detailed simulation and experimental results are presented in this paper for a 6.0-kW surface permanent-magnet synchronous machine. Both the simulation and experimental results show the required performance of the proposed system. [ABSTRACT FROM AUTHOR]

Single-stage power-factor-corrected (S2PFC) power supplies usually suffer from high voltage stress, due to lack of control on the intermediate bus capacitor voltage. In the past, analysis of such voltage stress was mostly based on steady-state condition without providing sufficient explanation during the transient circuit operation. This paper revisits the problem at circuit level and reports that the root cause is due to the inherent negative current feedback property of the output inductor or the transformer operating in continuous conduction mode (CCM). Based on the finding, this paper further proposes a new approach to reducing the voltage stress by adding an auxiliary circuit branch to existing S2PFC converters. The additional circuit branch limits the effect of negative current feedback by suppressing the change of output current slope due to change of load. This assists the pulsewidth modulation controller to track the change of load better such that the bus capacitor voltage range is reduced through duty cycle control. The auxiliary circuit branch also reduces reverse-recovery-related losses of the converter under CCM operation. A laboratory prototype using the popular boost PFC converter combined flyback dc/dc converter was built and tested to confirm the analysis and effectiveness of the approach. [ABSTRACT FROM AUTHOR]

A four-level five-phase open-end winding (OeW) drive topology is introduced in this paper. The drive comprises a five-phase induction machine with open-end stator windings, supplied using two two-level voltage-source inverters with isolated and unequal dc-link voltages, in the ratio 2 : 1. The topology offers the advantages of a modular structure with fewer semiconductor components and has a greater potential for fault tolerance, as compared with an equivalent single-sided four-level drive. Due to the large number of switching states, development of a suitable space vector pulsewidth-modulation (PWM) method can be challenging. Hence, this paper examines the implementation of two-level-shifted carrier-based PWM methods. The effect of dead time on the drive performance is discussed, and it is shown that simultaneous PWM switching of both inverters can lead to degraded output phase voltage waveforms. Detailed analysis of this phenomenon is presented, a solution is proposed, and the modified modulation techniques are incorporated in an experimental setup, at first in conjunction with $V/f$ control. Once the proof of concept has been provided, full field-oriented control is implemented in this OeW drive topology for the first time; detailed experimental testing is conducted, and results are reported. [ABSTRACT FROM AUTHOR]

Multiphase variable-speed drives and generation systems (systems with more than three phases) have become one of the mainstream research areas during the last decade. The main driving forces are the specific applications, predominantly related to the green agenda, such as electric and hybrid electric vehicles (EVs), locomotive traction, ship propulsion, “more-electric” aircraft, remote offshore wind farms for electric energy generation, and general high-power industrial applications. As a result, produced body of significant work is substantial, making it impossible to review all the major developments in a single paper. This paper therefore surveys the recent progress in two specific areas associated with multiphase systems, namely power electronic supply control and innovative ways of using the additional degrees of freedom in multiphase machines for various nontraditional purposes. [ABSTRACT FROM AUTHOR]

Multilevel inverters have created a new wave of interest in industry and research. While the classical topologies have proved to be a viable alternative in a wide range of high-power medium-voltage applications, there has been an active interest in the evolution of newer topologies. Reduction in overall part count as compared to the classical topologies has been an important objective in the recently introduced topologies. In this paper, some of the recently proposed multilevel inverter topologies with reduced power switch count are reviewed and analyzed. The paper will serve as an introduction and an update to these topologies, both in terms of the qualitative and quantitative parameters. Also, it takes into account the challenges which arise when an attempt is made to reduce the device count. Based on a detailed comparison of these topologies as presented in this paper, appropriate multilevel solution can be arrived at for a given application. [ABSTRACT FROM AUTHOR]

In order to solve the neutral-point voltage unbalancing problem for three-level inverters, this paper proposes a method to balance the neutral-point voltage for three-level inverters with variable modulation wave offset sinusoidal pulse-width modulation (SPWM) control. Based on the mathematical expressions of neutral-point voltage unbalancing, the factors are studied, which affect the fluctuation of neutral-point voltage. Theoretically the mathematical expressions of the neutral-point voltage with the proposed method are derived, and the mathematical relationship between the fluctuation of neutral-point voltage and the adjusting offset of modulation wave is studied. This proposed method realizes controlling the neutral-point voltage balance by dynamically calculating the offset superimposed to the modulation wave based on SPWM (DCOSPWM). This DCOSPWM method is very simple, which has good steady-state performance and is easy for digital implementation. The simulation results verify the correctness of the theoretical analysis in this paper, and the feasibility and effectiveness of this method is verified by the experiments in the experimental platform of neutral point clamped three-level inverters based on digital signal processor (DSP)-complex programmable logic device (CPLD). [ABSTRACT FROM AUTHOR]