Search

The generator voltage of a cutting-edge wind turbine generation system (WTGS) is expected to increase from the conventional low-voltage level of 690 V to a medium-voltage level of 6.6 kV with a power level up to 10 MW without the application of a parallel connection of multiple power units. On the other hand, it is difficult to use a conventional two-level or three-level converter in a WTGS with a dc-link voltage of 10–13 kV owing to the limitations on the voltage ratings of power devices. This paper presents a 10-MW WTGS consisting of a three-phase open-winding synchronous generator equipped with six lead terminals and a modular multilevel cascade converter (MMCC) formed by three identical subconverters. The MMCC carries out direct ac/ac power conversion from three single-phase voltages with a time-varying frequency (from the generator) to a three-phase voltage with a line frequency of 50 Hz. This paper discusses the operating principles and control methods for the WTGS, followed by simulations using the software package PSCAD/EMTDC. The experimental result obtained from a 200 V 6-kW downscaled system confirms the reliability of simulation results of the complete three-phase system.

This paper provides theoretical and experimental discussions on an optimal carrier frequency for a phase-shifted pulsewidth modulation modular multilevel cascade converter for grid connections. The theoretical discussion concludes that a ratio of the optimal carrier frequency with respect to the supply (ac) frequency is 5/2. A three-phase downscaled front-to-front system is designed, constructed, and tested to confirm validity of the theoretical discussion. It consists of a pair of three-phase modular multilevel cascade converters rated at 400 Vdc and 10 kW, where the carrier frequency is set to 450 Hz and the ac frequency to 180 Hz, that is, their ratio is equal to 5/2. Moreover, simulated waveforms are compared to experimental ones under the same operating conditions. Both experimental and simulated waveforms agree well with each other not only in steady states but also in transient states.

This paper focuses on the zero-voltage ride-through (ZVRT) capability of a transformerless back-to-back (BTB) system intended for installation on a power distribution system with many distributed power generators. The BTB system consists of two modular multilevel cascade converters based on double-star chopper cells (MMCC-DSCC) and their ac sides are connected to a common ac mains via ac-link inductors. This paper provides an experimental discussion on the DSCC-based BTB system under voltage sags by using a three-phase 200-V 10-kW downscaled system. Experimental results show that the BTB system is equipped with ZVRT capability without causing any overvoltage and/or overcurrent even under the most severe voltage sags.

This paper provides experimental verification of a modular multilevel cascade converter based on triple-star bridge cells (MMCC-TSBC) for a low-speed, high-torque motor drive. The TSBC is one of direct ac-to-ac power converters capable of achieving bidirectional power flow and drawing/feeding three-phase sinusoidal input (supply-side) and output (motor-side) currents with any power factor at both sides. This paper designs, constructs, and tests a downscaled drive system combining a 400-V, 15-kW, phase-shifted-carrier PWM TSBC equipped with four bridge cells per cluster and a 320-V, 38-Hz, 6-pole, 15-kW induction motor loaded at the rated torque. Experimental waveforms obtained from the downscaled drive system verify stable operation across a broad range from a standstill to the rated speed, showing satisfactory start-up performance.

The modular multilevel cascade converter (MMCC) family has been attracting attention from power electronics and power system engineers because it has been showing considerable promise as one of the next-generation high-power high-voltage/medium-voltage power converters. This paper provides an intensive discussion on power-flow analysis of three MMCC members with star configuration, focusing on dc-mean-voltage balance/regulation and ac-voltage mitigation control of all the floating dc capacitors. Most existing analysis methods are based on single-phase circuits, which make it difficult to derive capacitor voltage regulation/mitigation methods relying only on circulating currents and zero-sequence voltage. The power-flow analysis and regulation/mitigation methods developed in this paper are characterized by applying the αβ0 coordinate transformation(s). The validity of the power analysis and the regulation/mitigation method is confirmed by simulation using the PSCAD/EMTDC software package.

This paper presents an intensive discussion on a transformerless back-to-back (BTB) system using modular multilevel cascade converters based on double-star chopper cells (MMCC-DSCC). It is expected to be applied to a power distribution system with many distributed power generators. This paper designs, constructs, and tests a three-phase 200-V, 10-kW DSCC-based BTB system installed on a 200-V, 40-kW power distribution simulator consisting of two radial feeders. Experimental results show that the BTB system can mitigate power-flow imbalance between the two feeders. Moreover, the zero-sequence current circulating between the two feeders can be suppressed to be as small as 10 mA ( $0.02\%$ ) in rms by connecting a common-mode choke to the common dc link of the BTB system.

This paper provides an intensive discussion on analysis, simulation, and experiment of a back-to-back (BTB) system unifying two modular multilevel cascade converters based on double-star chopper cells (MMCCs-DSCCs). Each of the two DSCCs connected back-to-back consists of multiple cascaded chopper cells and a center-tapped inductor per leg. Low voltage steps bring significant reductions in harmonic voltage and current to the BTB system. Neither dc-link capacitor nor voltage sensor is required for regulating the dc-link voltage and controlling the dc-link current. A three-phase 200-V, 10-kW, 50-Hz downscaled BTB system with phase-shifted PWM is designed, constructed, and tested to verify its operating principles and performance. Analytical, simulated, and experimental results agree well with each other in steady and transient states. Experimental waveforms confirm the effectiveness of a self-starting/restarting procedure.