Search

The present work focuses on performance improvement and emission reduction of conventional diesel engine's performance by incorporating various designs of intake manifolds while operating on different alternative fuels. The intake manifold was designed in a helical shape to produce higher turbulence in the combustion chamber. Three intake manifolds were designed while varying the internal diameter (ID) of helical shape, namely 1, 2 and 3 ID. In this study, the engine was operated on various alternative fuels, i.e., lemongrass oil, linseed oil and gas-to-liquid fuels. The improvement in performance and reduction in emission of the engine were highest for the engine connected with the 1-ID intake manifold. The gas-to-liquid fuel having the greater cetane number as output of the results is decreased the peak pressure. The oxides of nitrogen were significantly reduced by 51% for the engine connected with the 1-ID design manifold, and exhaust gas temperature also slightly decreased 24% when correlated with the diesel fuel. The presence of more oxygen content in the biodiesel used in the 1-ID manifold design shows the result in reduction of CO and HC by 35% and 46%, respectively, when correlated with the base fuel.

Exploring non-platinum group metal (n-PGM) based efficient oxygen reduction reaction (ORR) electro-catalysts is highly important for realizing advancement in sustainable next generation-alkaline anion exchange membrane fuel cells (AAEMFCs). Herein, we demonstrate a new “hierarchical shape tuning approach” for the synthesis of controlled sized and shaped non-PGM based Ag ORR electro-catalysts with surface active nano-islands. Hierarchical shapes ranging from spherical (S-AgNs), worm-in-sphere, sphere-in-worm and vermiform (worm-like) Ag nanostructures (V-AgNs) were obtained by precisely varying the ratios of capping agent to dual reducing agents in water at ambient conditions. Compared to S-AgNs, V-AgNs revealed a higher mass normalized ORR Tafel activity (0.303 A mgAg−1 at 0.9 V), onset (1.06 V) and half wave (0.78 V) potentials and higher retention of limiting current density (>88%) after 5000 cycles in 0.5 M potassium hydroxide (KOH) solution attributable to their unique worm like morphology with surface active nano-islands and support free-nature enabled better catalyst utilization. In a fully “non-PGM AAEMFC” (n-PAAEMFC), V-AgNs exhibited the highest fuel cell activity of 115.6 mW cm−2 and stable short-term durability (∼240 h) compared to S-AgNs (41.3 mW cm−2) and previously reported fully n-PAAEMFCs indicating their potential use in next-generation alkaline fuel cells.

A solid-state planar reference electrode (SSPRE) was fabricated and evaluated using polymer membrane, comprising polyvinyl chloride-co-polyvinyl acetate, nitrophenyl octyl ether as plasticizer, and potassium tetraphenylborate as anion blocker, and was used for the fabrication of SSPRE. Screen-printed Ag/AgCl electrode was used as the base electrode for the fabrication of SSPRE and was evaluated in background electrolyte solutions containing KNO3/KCl and was observed that there was no significant potential dependence on anions present in the background electrolyte. Furthermore, SSPRE was tested using a series of cations and anions in solution and varying pH of the background electrolyte with respect to commercial Ag/AgCl with 0.1 M KCl reference electrode. It was noted that the SSPRE provided stable potential by tuning the design of the screen-printed electrodes and the membrane potential. The reference potential does not differ in various background electrolyte solutions, except thiocyanate, which gave a negative shift at high concentration, ca. 0.1 M. Furthermore, the SSPRE was integrated with screen-printed potassium and sodium ion-selective electrodes, and was tested, and the performance was evaluated.

For the first time, we report a facile one pot aqueous method for support-free Pd85Pt15 nano-porous structures (NPoS) synthesis from PdMn nano-alloys at ambient conditions. A hierarchical approach was successfully employed through a simple “self-settlement” process with descending amounts of carbon to carbon-free electro-catalysts to improve catalyst utilization and avoid carbon degradation during fuel cell operating conditions. Pd85Pt15 NPoS exhibits enhanced methanol resistive oxygen reduction reaction (ORR) activity owing to the presence of highly active and unique surface PdPt islands compared to HiSPEC Pt/C catalysts. Accelerated durability tests of the support-free PdPt NPoS show enhanced durability in harsh acidic environment (1.0 N H2SO4) compared to HiSPEC Pt/C and DOE 2017–2020 durability target. Preliminary direct methanol fuel cell studies using hierarchically derived Pd85Pt15 NPoS variants were performed at ultra-low Pt content. The effects of carbon content and catalyst layer thickness on fuel cell activities are well discussed.

Poly(fluorene-alt-benzothiadiazole) having 5 and 10% equivalent meso-tetraphenylporphyrin (m-MTPCC) linked through oxyethylene spacer in carbazole (P2, P3) and the parent poly(9,9-di-hexylfluorene-alt-2,1,3-benzothiadiazole) (P1) were synthesized using Suzuki polymerization reaction. These polymers were characterized using FT-IR, 1H NMR, TGA and gel permeation chromatography. The synthesized polymers are soluble in common organic solvents and are found to be thermally stable. Weight average molecular weights of the polymers were 51.895, 71.224 and 34.789 kDa for P1, P2 and P3, respectively. These copolymers (P2 and P3) shows absorption maxima at around 320, 422, 452 nm and emission maxima at 540 nm in solution, whereas in film state, these polymers (P2 and P3) shows absorption maxima at around 322, 422, 466 and 554 nm and emission at around 539, 654 and 718 nm. The photoluminescence emission at 648 and 720 nm when excited at 320 nm shows that energy transfer from polymer backbone to porphyrin. Surface morphology, optical absorption and emission properties of these polymers with PCBM were also studied. Electrochemical characterization of these polymers shows deep HOMO levels for P2 and P3 when compared with parent polymer and the details are reported.

Herein, we report a simple and elegant aqueous synthesis of Pd100-xPtx (x=5, 10, 15 and 20) nano-porous structures (NPoS) derived from Pd100-xMn2x (x=5, 10, 15 and 20) nano-alloys. Pd100-xPtx/C NPoS exhibit enhanced oxygen reduction reaction (ORR) activity along with higher retention of figure of merit in the presence of methanol compared to HiSPEC Pt/C catalyst. The ORR mass and specific activity values of Pd100-xPtx/C NPoS are high and exceed the U.S. department of energy (DOE) 2017–2020 targets. The enhanced methanol tolerance and ORR activity of Pd100-xPtx/C NPoS is attributed to their unique surface active Pd−Pt islands on nano-porous Pd. Direct methanol fuel cell performance studies employed using Pd85Pt15/C NPoS as cathode material (0.4 mgPt/cm2) and HiSPEC PtRu/C NPs as anode material (0.2 mgPt/cm2) shows improved direct methanol fuel cell (DMFC) single cell activity at low Pt loading and the results are presented.

We report an enhanced power conversion efficiency (PCE) of 11.7% ± 0.2 and a fill factor (FF) of 71% for dye-sensitized solar cells (DSSC) with an active area of 0.16 cm2 after modifying the TiO2photoanode with size-selective (ca. 2 nm) N,F,S-codoped graphene quantum dots (NFS-GQDs) that exhibit a photoluminescence quantum yield (PLQY) of 70%. An upward shift in the Fermi level has been observed, perhaps responsible for the improved performance along with the possibility of preventing the back electron transfer from TiO2. Mott Schottky analysis indicates a shift (52 mV)in the flat band potential, which is directly related to the Voc of the system. Detailed characterization (IPCE, TCSPC etc) indicates the important role of hetero atoms in facilitating the enhanced performance. Thus, our results suggest that the incorporation of size controlled, hetero atom doped GQDs can enhance the efficiency of DSSCs enabling more opto-electronic applications.

Gold-platinum nano-porous structures (Au100-xPtx NPoS) with unique surface enriched Au−Pt islands are synthesised through a galvanic replacement strategy from Au100-xAg2x nano-alloys with ultra-low platinum loading (x=1.25, 2.5 and 5). Formic acid oxidation reaction (FAOR) on Au100-xPtx/C NPoS shows a distinct peak at around 0.5 V related to CO2 formation. A characteristic peak at around 1.5 V increases with increasing FA concentration owing to the direct FAOR by nano-porous Au centers. FAOR peaks and If/Ib peak current ratios indicates that, Au100-xPtx/C NPoS facilitates direct FAOR pathway unlike HiSPEC Pt/C (dehydration pathway). Based on the enhanced chrono-amperometric response, Tafel behaviour and mass activity values, Au97.5Pt2.5/C NPoS (5.5 A/mgPt) reflects as the optimal catalyst for efficient FAOR. The intriguing catalytic role of surface enriched Au−Pt islands present on nano-porous Au greatly helps in determining the superior FAOR activity in Au97.5Pt2.5/C NPoS towards direct dehydrogenation pathway at ultra-low Pt content compared to other NPoS and HiSPEC Pt/C catalysts.

We demonstrate electrochemical cycling-induced reduction of MoO3 to monoclinic molybdenum dioxide and molybdenum sub-oxides (MoO3-x), which exhibit excellent electrochemical hydrogen evolution reaction (HER) activity. The conversion of MoO3 during cycling was probed; after 250 cycles, the redox peaks were found to diminish with an onset potential shift and increased HER current density. At 400 cycles, the insertion/deinsertion processes observed in the initial cycles are completely absent and the HER current density is enhanced to the maximum. The effect of MoO3 morphology and size on the electrochemical reduction of MoO3 was also studied.

A series of alternate block copolymers of polyphenylene vinylenes that have 1,3-dioctyloxy phenylene in the center of kinked m-terphenyl group as one of the building blocks with either one of the aromatic groups, viz., 1,4-dioctyloxy benzene, 4,6-dioctyloxy benzene and 4,4′-dioctyloxy biphenyl, was synthesized through Heck polymerization. These alternate block copolymers, viz., poly(2,5-bis(octyloxy)phenylene vinylene alt 4′,6′-bis(octyloxy)-1,1′:3′,1″-terphenylene) (P1), poly(2,4-bis(octyloxy)phenylene vinylene alt 4′,6′-bis(octyloxy)-1,1′:3′,1″-terphenylene) (P2) and poly(4,4′-bis(octyloxy-3,3′-biphenylene vinylene alt 4′,6′-bis(octyloxy)-1,1′:3′,1″-terphenylene) (P3), were characterized for their thermal and optical properties. The synthesized polymers had good solubility in organic solvents and were stable up to 350 °C. The molecular weights of the synthesized polymers were in the range 4370–10,900 Da with polydispersity range 1.52–1.65, which were measured by the gel permeation chromatography technique. The optical properties of these polymers showed absorptions in solution at around 400, 329, and 345 nm for P1, P2, and P3 polymers, respectively. The photoluminescence emission maxima of the polymers were at around 461 nm with a shoulder 439 and 424 nm for P1, P2, and P3, respectively. Photoluminescence emission of films of these polymers showed minimum redshift (20 nm) when compared with spectra of their solutions. The optical and photoluminescence emission properties of these polymers were found to vary on the backbone structure.

In the present work, a siloxane based flexible substrate for optoelectronic applications with improved flexibility and high temperature withstanding capacity has been fabricated and the details are reported. The structural and optical properties of the substrate were characterized and the optical transparency is found to be about 90% − 95% in the visible region. The substrate withstands temperatures up to 300 °C without significant degradation and has a low thermal coefficient of expansion. Fourier transform infrared spectral data show the materials in the prepared substrate and SEM studies show the surface and cross-sectional characteristics of the substrate. It has good mechanical strength, can withstand a high breaking load of 7 N, has a average tensile strength of 48.86 MPa and high average tensile modulus of 127.32 and also possesses excellent surface smoothness and resistance to both chemical and moisture with better rigidity; it will be a long lasting alternative for flexible plastic substrates. The optical characteristics such as refractive index (n) and extinction coefficient (k) are also reported. © 2016 Society of Chemical Industry

Organic Light Emitting Diode (OLED) has major applications in the field of displays, lighting and visible light communication. Due to the advantages of low cost, light weight, low power and high efficiency, flexible organic light emitting diode have attracted the interest of researchers all over the World. Flexible OLEDs are considered to be the best suitable candidate for next generation lighting devices. In this research, a new flexible and transparent substrate with an average transmittance of 60-70% in the visible region (300-700nm) is synthesized with the help of organic materials such as tetraphenylphosphonium modified lithium saponite (TPP-LiSA), Synthetic Saponite (SA) and N, N-dimethylformamide (DMF). The as-synthesized substrate exhibits refractive index as close as glass which makes this substrate to be used for flexible displays. Characteristics such as extinction coefficient (k), absorption of the synthesized substrate are also calculated.

Cross-linked polymer (CLP) composed of poly(ethylene glycol) methyl ether acrylate and poly(ethylene glycol) diacrylate has been used in synthesizing gel electrolyte. A set of electrolyte samples was synthesized using gel casting method by varying the weight percentage ratio of cross-linked polymers from 2–14 % in an incremental order (2 %) with respect to poly (ethylene oxide) (PEO) and evaluated its performance by employing in the fabrication of dye-sensitized solar cells. The synthesized polymer was subjected to different analytical techniques such as NMR, TGA, DSC, GPC, and FTIR to confirm the materials. The molecular weight of the CLP has been measured using GPC and the obtained value is found to be 3.655 KDa with polydispersity of 1.94. The CLP-PEO gel electrolyte with 10 % weight ratio has obtained the highest ionic conductivity of 3.07 × 10−6 S/cm−1 at room temperature and best photo-conversion efficiency of 5.1 % was achieved for the same.

An effectual functionalized synthetic resin involving anthranilic acid/4-nitroaniline/formaldehyde was synthesized for the detoxification of hazardous metal ions. The resin was characterized by Fourier transform infrared, 1H, and 13C nuclear magnetic resonance spectroscopy, and its morphology was established through scanning electron microscope and X-ray diffraction. The resin was analyzed by thermogravimetric analysis to assess the thermal stability, in which the resin could be used in high temperature aqueous solutions for the elimination of harmful metal ions. The ion-exchange property of the resin was evaluated by batch technique for specific metal ions viz. Fe3+, Co2+, Ni2+, Cu2+, Zn2+, and Pb2+. The study was extended to three variations such as effect of metal ion uptake in the presence of various electrolytes in different concentrations, effect of pH, and effect of contact time. The outcome proved that the resin can be used as a strong cation-exchanger to remove various metal ions from the solutions. The resin could be regenerated and reused with quantitative recovery of metal ions for few cycles. On comparison with the earlier reported resins, the synthesized resin has found excellent capability of metal ion recovery. The resin possesses an utmost ion-exchange capacity, which is in good harmony with isotherm models and kinetics. Copyright © 2015 John Wiley & Sons, Ltd.

Poly(fluorene-alt-carbazole) appended with meso-tetraphenylporphyrin (MTPPC) linked through oxyethylene spacer and the parent poly(N-hexyl-2,7-carbazole-alt-9,9-di-n-hexyl fluorene) (P1) were synthesized and characterized. Optical absorption properties of the polymers containing 5% of MTPPC (P2) and 10% of MTPPC (P3) in the polymer backbone show extended optical absorption toward long wavelength compared to the parent polymer P1. Optical absorption studies of the polymers showed that polymer P1 has absorption at 384 nm in solution, whereas polymers P2 and P3 have absorption at 384 nm corresponding to polymer backbone and soret band at 421 nm with Q bands at around 518 and 554 nm in solution. P1 shows photoluminescence emission around 417 nm, whereas P2 and P3 fall around 656 nm. Thermal, electrochemical, and quenching studies of the polymers have been studied and the details are reported.

Recent developments in the field of flexible electronics motivated the researchers to start working in verdict of new flexible substrate for replacing the existing rigid glass and flexible plastics. Flexible substrates offer significant rewards in terms of being able to fabricate flexible electronic devices that are robust, thinner, conformable, lighter and can be rolled away when needed. In this work, a new flexible and transparent substrate with the help of organic materials such as Polydimethylsiloxane (PDMS) and tetra ethoxy orthosilicate (TEOS) is synthesized. Transmittance of about 90–95% is acquired in the visible region (400–700[Formula: see text]nm) and the synthesized substrate shows better thermal characteristics and withstands temperature up to 200[Formula: see text]C without any significant degradation. Characteristics such as transmittance ([Formula: see text]), absorption ([Formula: see text]), reflectance ([Formula: see text]), refractive index ([Formula: see text]) and extinction coefficient ([Formula: see text]) are also reported.