Search

Background For clinical care and research in vitiligo, photographs with the use of ultraviolet (UV) light or Wood's lamp are often made. Conventional cameras are insensitive to UV light. The use of a UV camera (UV photography) might improve image quality and ameliorate the assessment of target lesions in vitiligo. Objectives To determine image quality and the validity and reliability of UV photography for the assessment of vitiligo target lesions. Methods Images of patients with vitiligo were made with UV photography and a conventional camera, and lesions were drawn on graph paper and transparent sheets. Image quality was scored by vitiligo experts and medical interns. The intraclass correlation coefficients (ICCs) of the lesion size determined with UV photography combined with digital surface measurement and the other techniques were hypothesized to be above 0.6. The ICCs between UV images taken by the same physician and between two different physicians were calculated for determining inter‐ and intra‐reliability. Results In total, 31 lesions of 17 patients were included. Image quality was assessed as good or very good for 100% and 26% for UV photography and the conventional camera, respectively. ICCs of UV photography and the conventional camera, drawing the lesions on transparent sheets and graph paper, were 0.984, 0.988 and 0.983, respectively, confirming our hypotheses. The ICCs of the intra‐rater and inter‐rater were 0.999 and 0.998, respectively. Conclusions The results of this study indicate that the use of UV photography for the assessment of vitiligo lesions improves image quality and is valid and reliable.

During health crises, including terrorist attacks or pandemics like coronavirus disease 2019 (COVID-19), the number of mechanical ventilators might fall short of the number of patients with severe respiratory failure [1–3]. A possible emergency solution is to ventilate multiple patients with one ventilator. Sharing ventilators was applied anecdotally during the 2017 Las Vegas (USA) shootings and has raised interest in lay media with the current COVID-19 pandemic [4]. However, ventilating two patients with one ventilator can be dangerous when incorrectly applied. Different setups have been published online, but none have reported any technical safety testing., With a modified circuit, it is feasible to ventilate two patients with one ventilator over a relevant range of compliances. Adding inspiratory resistance allows individual titration of tidal volume, and incorporating one-way valves prevents pendelluft. https://bit.ly/3ex8SYP

Contains fulltext : 229910.pdf (Publisher’s version ) (Open Access) OBJECTIVES/HYPOTHESIS: To provide insight in the thermal effects of individual laser settings in target tissues to optimize flexible endoscopic CO(2) laser surgery treatment. STUDY DESIGN: Experimental laboratory study. METHODS: Thermal effects of the CO(2) laser using a fiber delivery system were visualized using the color Schlieren technique in combination with a polyacrylamide gel tissue model. Variable settings were used for emission mode, power, laser fiber distance, and laser duration, which were evaluated in every possible combination. Collateral thermal expansion and incision depth were measured. To validate the model, the results were compared to histology after CO(2) laser irradiation of ex vivo human vocal cords, and the intraclass correlation coefficient was calculated. Thermal damage and incision depth were measured by a blinded pathologist. RESULTS: Of all parameters studied, duration of laser irradiation had the greatest effect on thermal expansion. Increased distance between laser tip and target tissue resulted in significantly reduced incision depth and increased thermal expansion. Pulsed emission modes led to increased incision depths. The intraclass correlation coefficient for consistency between the model setup and the ex vivo human vocal cords was classified as "fair." CONCLUSIONS: By using high-intensity pulsed lasers at minimal distance to the target tissue, exposure times and subsequent damage to surrounding tissue can be reduced. If an evaporation technique is used, lower power in continuous wave at a larger distance to the target tissue will lead to superficial but broader thermal effects. The model setup used in this study is a valid model to investigate laser-induced thermal effects in vocal cord tissue. LEVEL OF EVIDENCE: NA Laryngoscope, 130:E680-E685, 2020.

The Initial Systolic Time Interval (ISTI), obtained from the electrocardiogram (ECG) and impedance cardiogram (ICG), is considered to be a measure for the time delay between the electrical and mechanical activity of the heart and reflects an early active period of the cardiac cycle. The clinical relevance of this time interval is subject of study. This paper introduces a method using ISTI to evaluate and predict the circulatory response to fluid administration in patients after coronary artery bypass graft surgery and presents preliminary results of a pilot study by comparing ISTI with cardiac output (CO) responsiveness. Also the use of the pulse transit time (PTT), earlier recommended for this purpose, was investigated. The results showed an inverse relationship between ISTI and CO at all moments of fluid administration and also an inverse relationship between the changes ΔISTI and ΔCO before and after full fluid administration. No relationships between PTT and CO or ΔPTT and ΔCO were found. It is concluded that ISTI is dependent upon preload, and that ISTI has the potential to be used as a clinical parameter assessing preload.

Due to the high rates of epidural failure (3–32%), novel techniques are required to objectively assess the successfulness of an epidural block. In this study we therefore investigated whether thermographic temperature measurements have a higher predictive value for a successful epidural block when compared to the cold sensation test as gold standard. Epidural anesthesia was induced in 61 patients undergoing elective abdominal, thoracic or orthopedic surgery. A thermographic picture was recorded at 5, 10 and 15 min following epidural anesthesia induction. After 15 min a cold sensation test was performed. Epidural anesthesia is associated with a decrease in skin temperature. Thermography predicts a successful epidural block with a sensitivity of 54% and a PPV of 92% and a specificity of 67% and a NPV of 17%. The cold sensation test shows a higher sensitivity and PPV than thermography (97 and 93%), but a lower specificity and NPV than thermography (25 and 50%). Thermographic temperature measurements can be used as an additional and objective method for the assessment of the effectiveness of an epidural block next to the cold sensation test, but have a low sensitivity and negative predictive value. The local decrease in temperature as observed in our study during epidural anesthesia is mainly attributed to a core-to-peripheral redistribution of body heat and vasodilation.

Background and Objective: Endoscopic third ventriculostomy is used to treat hydrocephalus. Different laser wavelengths have been proposed for laser-assisted endoscopic third ventriculostomies over the last decades. The aim of this study was to evaluate Thulium laser endoscopic third ventriculostomy heat penetration in the surrounding environment of the floor of the third ventricle in an in vitro setting with visualization of thermal distribution. Subsequently 106 Thulium laser endoscopic third ventriculostomy procedures were retrospectively analyzed to demonstrate safety. Methods: The in vitro visualization was based on the color Schlieren method. The heat penetration was measured beneath a tissue phantom of the floor of the third ventricle with a fiber of 365 μm in diameter at different energy settings; 1.0W (956 J/cm2), 2.0W (1,912 J/cm2), 4.0W (3,824 J/cm2), and 7.0W (6,692 J/cm2), with a pulse duration of 1.0 second. All experiments were repeated five times. In addition, 106 Thulium laser endoscopic third ventriculostomy procedures between 2005 and 2015 were retrospectively analysed for etiology, sex, complications, and laser parameters. Results: In the energy settings from 1.0 to 4.0 W, heat penetration depth beneath the phantom of the third ventricle did not exceed 1.5 mm. The heat penetration depth at 7 W, exceeded 6 mm. The clinical overall success rate was 80% at the 2-year follow-up study. Complications occurred in 5% of the procedures. In none of the 106 investigated clinical patients bleeding or damage to the basilar artery was encountered due to Thulium laser ablation. Conclusions: The in vitro experiments show that under 4.0W the situation is considered safe, due to low penetration of heat, thus the chance of accidentally damaging critical structures like the basilar artery is very small. The clinical results show that the Thulium laser did not cause any bleeding of the basilar artery, and is a safe technique for laser endoscopic third ventriculostomy. Lasers Surg. Med. 50:629–635, 2018. © 2017 Wiley Periodicals, Inc.

Comparing and selecting an adequate spectral filter array (SFA) camera is application-specific and usually requires extensive prior measurements. An evaluation framework for SFA cameras is proposed and three cameras are tested in the context of skin analysis. The proposed framework does not require application-specific measurements and spectral sensitivities together with the number of bands are the main focus. An optical model of skin is used to generate a specialized training set to improve spectral reconstruction. The quantitative comparison of the cameras is based on reconstruction of measured skin spectra, colorimetric accuracy, and oxygenation level estimation differences. Specific spectral sensitivity shapes influence the results directly and a 9-channel camera performed best regarding the spectral reconstruction metrics. Sensitivities at key wavelengths influence the performance of oxygenation level estimation the strongest. The proposed framework allows to compare spectral filter array cameras and can guide their application-specific development. c 2019 by the authors. Licensee MDPI, Basel, Switzerland. This article is an open access article distributed under the terms and conditions of the Creative Commons Attribution (CC BY) license (http://creativecommons.org/licenses/by/4.0/).

Smart phones have come out with advanced features that can be useful for medical diagnosis. The Iphone X has a face recognition function to unlock the phone which could actually be used as a full functional 3D scanner. Unfortunately, only a few app developers have seen the potential of the Iphone X. The Bellus3D IOS app is dedicated for face scanning with the option to export data in slt/obj format for analysis on other software platforms. The face scans can be performed in 30 seconds including processing. A hardware adaption was developed to perform 3D scans also in the direction of backside of the Iphone X. To test the resolution and color representation of the Iphone X, scans were obtained of face phantoms and compared with high-end 3D scanners (Artec Spider/EVA and Vectra) using deviation maps. The Iphone X/Bellus3D performed best for the front view of the face. Presence of hair resulted in distortion of the side view. The mesh density was around 0.6-0.8 mm which is less compared to the Artec scanners (

Currently, allergy testing is performed by exposing the skin to small quantities of potential allergens on the inner forearm thereby scratching the protective epidermis to increase exposure. After 15 minutes the dermatologist performs a visual check of the 'bump' induced by swelling and erythema. In this study, two high resolution 3D scanners (Artec Spider and EVA) were used to quantify the dimensions (circumference, surface area, thickness) of the bump and to assess which parameters correlate with the diagnosis of the dermatologist. For comparison and validation of the scanners and the analysis-software (Artec Studio and GOM Inspect), phantom 'bumps' were developed. In a small clinical feasibility study, data of 3 patients with 17 positive allergic reactions were obtained and analyzed with the optimum settings based on the phantom study. Although both scanners could differentiate between the reaction grade 1, 2 or 3 assigned by the dermatologist, the results were not significant due to the small number of reactions at this time of the study. Both in the phantom and clinical study, the Artec Spider 3D scanner showed the allergic reactions clearly but an practical method of analysis needs to be developed to grade them similar to dermatologists. The resolution of the Artec EVA 3D scanner is lower but this scanner is more practical for use in the clinic (fast and easy to use). 3D scanners have a great potential for quantitative imaging in dermatology and aesthetic surgery.

Recently, low cost smart phone based thermal cameras are being considered to be used in a clinical setting for monitoring physiological temperature responses such as: body temperature change, local inflammations, perfusion changes or (burn) wound healing. These thermal cameras contain uncooled micro-bolometers with an internal calibration check and have a temperature resolution of 0.1 degree. For clinical applications a fast quality measurement before use is required (absolute temperature check) and quality control (stability, repeatability, absolute temperature, absolute temperature differences) should be performed regularly. Therefore, a calibrated temperature phantom has been developed based on thermistor heating on both ends of a black coated metal strip to create a controllable temperature gradient from room temperature 26 °C up to 100 °C. The absolute temperatures on the strip are determined with software controlled 5 PT-1000 sensors using lookup tables. In this study 3 FLIR-ONE cameras and one high end camera were checked with this temperature phantom. The results show a relative good agreement between both low-cost and high-end camera's and the phantom temperature gradient, with temperature differences of 1 degree up to 6 degrees between the camera's and the phantom. The measurements were repeated as to absolute temperature and temperature stability over the sensor area. Both low-cost and high-end thermal cameras measured relative temperature changes with high accuracy and absolute temperatures with constant deviations. Low-cost smart phone based thermal cameras can be a good alternative to high-end thermal cameras for routine clinical measurements, appropriate to the research question, providing regular calibration checks for quality control.

In the development of new near-infrared (NIR) fluorescence dyes for image guided surgery, there is a need for new NIR sensitive camera systems that can easily be adjusted to specific wavelength ranges in contrast the present clinical systems that are only optimized for ICG. To test alternative camera systems, a setup was developed to mimic the fluorescence light in a tissue phantom to measure the sensitivity and resolution. Selected narrow band NIR LED's were used to illuminate a 6mm diameter circular diffuse plate to create uniform intensity controllable light spot (μW-mW) as target/source for NIR camera's. Layers of (artificial) tissue with controlled thickness could be placed on the spot to mimic a fluorescent 'cancer' embedded in tissue. This setup was used to compare a range of NIR sensitive consumer's cameras for potential use in image guided surgery. The image of the spot obtained with the cameras was captured and analyzed using ImageJ software. Enhanced CCD night vision cameras were the most sensitive capable of showing intensities < 1 μW through 5 mm of tissue. However, there was no control over the automatic gain and hence noise level. NIR sensitive DSLR cameras proved relative less sensitive but could be fully manually controlled as to gain (ISO 25600) and exposure time and are therefore preferred for a clinical setting in combination with Wi-Fi remote control. The NIR fluorescence testing setup proved to be useful for camera testing and can be used for development and quality control of new NIR fluorescence guided surgery equipment.

It is difficult to obtain quantitative measurements as to surface areas and volumes from standard photos of the body parts of patients which is highly desirable for objective follow up of treatments in e.g. dermatology. plastic, aesthetic and reconstructive surgery. Recently, 3-D scanners have become available to provide quantification. Phantoms (3-D printed hand, nose and ear, colored bread sculpture) were developed to compare a range from low-cost (Sense), medium (HP Sprout) to high end (Artec Spider, Vectra M3) scanners using different 3D imaging technologies, as to resolution, working range, surface color representation, user friendliness. The 3D scans files (STL, OBJ) were processed with Artec studio and GOM software as to deviation compared to the high resolution Artec Spider scanner taken as †golden' standard. The HP Spout, which uses a fringe projection, proved to be nearly as good as the Artec, however, needs to be converted for clinical use. Photogrammetry as used by the Vectra M3 scanner is limited to provide sufficient data points for accurate surface mapping however provides good color/structure representation. The low performance of the Sense is not recommended for clinical use. The Artec scanner was successfully used to measure the structure/volume changes in the face after hormone treatment in transgender patients. 3D scanners can greatly improve quantitative measurements of surfaces and volumes as objective follow up in clinical studies performed by various clinical specialisms (dermatology, aesthetic and reconstructive surgery). New scanning technologies, like fringe projection, are promising for development of low-cost, high precision scanners.

The non-invasively measured initial systolic time interval (ISTI) reflects a time difference between the electrical and pumping activity of the heart and depends on cardiac preload, afterload, autonomic nervous control and training level. However, the duration of the ISTI has not yet been compared to other time markers of the heart cycle. The present study gauges the duration of the ISTI by comparing the end point of this interval, the C-point, with heart cycle markers obtained by echocardiography. The heart rate of 16 healthy subjects was varied by means of an exercise stimulus. It was found that the C-point, and therefore the end point of ISTI, occurred around the moment of the maximum diameter of the aortic arch in all subjects and at all heart rates. However, while the time difference between the opening of the aortic valves and the maximum diameter of the aortic arch decreased significantly with decreasing RR-interval, the time difference with respect to the moment of the C-point remained constant within the subjects. This means that the shortening of the ISTI with increasing heart rate in response to an exercise stimulus was caused by a shortening of the pre-ejection period (PEP). It is concluded that the ISTI can be used as a non-invasive parameter indicating the time difference between the electrical and mechanical pumping activity of the heart, both inside and outside the clinic.

High-speed thermal imaging enables visualization of heating of the vestibule during laser-assisted stapedotomy, comparing KTP, CO2, and Thulium laser light. Perforation of the stapes footplate with laser bears the risk of heating of the inner ear fluids. The amount of heating depends on absorption of the laser light and subsequent tissue ablation. The ablation of the footplate is driven by strong water absorption for the CO2 and Thulium laser. For the KTP laser wavelength, ablation is driven by carbonization of the footplate and it might penetrate deep into the inner ear without absorption in water. The thermal effects were visualized in an inner ear model, using two new techniques: (1) high-speed Schlieren imaging shows relative dynamic changes of temperatures up to 2 ms resolution in the perilymph. (2) Thermo imaging provides absolute temperature measurements around the footplate up to 40 ms resolution. The high-speed Schlieren imaging showed minimal heating using the KTP laser. Both CO2 and Thulium laser showed heating below the footplate. Thulium laser wavelength generated heating up to 0.6 mm depth. This was confirmed with thermal imaging, showing a rise of temperature of 4.7 (±3.5) °C for KTP and 9.4 (±6.9) for Thulium in the area of 2 mm below the footplate. For stapedotomy, the Thulium and CO2 laser show more extended thermal effects compared to KTP. High-speed Schlieren imaging and thermal imaging are complimentary techniques to study lasers thermal effects in tissue.

The emerging technology of spectral filter array (SFA) cameras has great potential for clinical applications, due to its unique capability for real time spectral imaging, at a reasonable cost. This makes such cameras particularly suitable for quantification of dynamic processes such as skin oxygenation. Skin oxygenation measurements are useful for burn wound healing assessment and as an indicator of patient complications in the operating room. Due to their unique design, in which all pixels of the image sensor are equipped with different optical filters, SFA cameras require specific image processing steps to obtain meaningful high quality spectral image data. These steps include spatial rearrangement, SFA interpolations and spectral correction. In this paper the feasibility of a commercially available SFA camera for clinical applications is tested. A suitable general image processing pipeline is proposed. As a &rsquo, proof of concept&rsquo, a complete system for spatial dynamic skin oxygenation measurements is developed and evaluated. In a study including 58 volunteers, oxygenation changes during upper arm occlusion were measured with the proposed SFA system and compared with a validated clinical device for localized oxygenation measurements. The comparison of the clinical standard measurements and SFA results show a good correlation for the relative oxygenation changes. This proposed processing pipeline for SFA cameras shows to be effective for relative oxygenation change imaging. It can be implemented in real time and developed further for absolute spatial oxygenation measurements.

Obtaining access to blood vessels can be difficult, especially in children. Visualization of subsurface blood vessels might be a solution. Ultrasound and visible light have been used to this purpose, but have some drawbacks. Near-infrared light might be a better option since subsurface blood vessels can be visualized in high contrast due to less absorption and scattering in tissue as compared to visible light. Our findings with a multispectral imaging system support this theory. A device, the VascuLuminator, was developed, based on transillumination of the puncture site with near-infrared light. The VascuLuminator was designed to meet the requirements of compact and safe use. A phantom study showed that the maximum depth of visibility (5.5mm for a 3.6mm blood vessel) is sufficient to visualize blood vessels in typical locations for peripheral venous and arterial access. A quantitative comparison of the VascuLuminator and to two other vessel imaging devices, using reflection of near-infrared light instead of transillumination, was conducted. The VascuLuminator is able to decrease failure at first attempt in blood withdrawal in pediatric patients from 10/80 (13%) to 1/45 (2%; P=.05).

OBJECTIVE: Subtle motion of an epileptic patient examined with co-registered EEG and functional MRI (EEG-fMRI) may often lead to spurious fMRI activation patterns when true epileptic spikes are contaminated with motion artefacts. In recent years, methods relying on reference signals for correcting these subtle movements in the EEG have emerged. In this study, the performance of two reference-based devices are compared to the template-based method with regard to their ability to remove movement-related artifacts in EEG measured during scanning.METHODS: Measurements were performed with a novel double layer cap consisting of 29 EEG and 29 reference electrodes, and with a current loop cap consisting of 60 electrodes and three current loop wires attached to the cap. EEG was acquired inside the scanner during resting state, as well as when the subject was performing a cued movement task. For the double layer cap recordings, newly developed artifact removal algorithms are introduced and both reference signal-based methods are compared to a template-based correction method.RESULTS: The BCG artifacts occurring at resting state could be removed successfully by both the reference signal-based methods as well as by the template-based method. However, the reference signal-based methods were also capable of removing EEG artifacts induced by subtle movements, whereas the template-based method failed to remove these artifacts.CONCLUSION: Reference signal-based methods enable to correct for artifacts due to subtle movements, which are not removed by commonly used template-based removal algorithms.SIGNIFICANCE: Sensitivity of EEG-fMRI analysis in patients with focal epilepsy is improved by avoiding erroneous detections of subtle movements as epileptic spikes in the EEG.

Adequate assessment of burn wounds is crucial in the management of burn patients. Thermography, as a noninvasive measurement tool, can be utilized to detect the remaining perfusion over large burn wound areas by measuring temperature, thereby reflecting the healing potential (HP) (i.e., number of days that burns require to heal). The objective of this study was to evaluate the clinimetric properties (i.e., reliability and validity) of thermography for measuring burn wound HP. To evaluate reliability, two independent observers performed a thermography measurement of 50 burns. The intraclass correlation coefficient (ICC), the standard error of measurement (SEM), and the limits of agreement (LoA) were calculated. To assess validity, temperature differences between burned and nonburned skin (?T) were compared to the HP found by laser Doppler imaging (serving as the reference standard). By applying a visual method, one ?T cutoff point was identified to differentiate between burns requiring conservative versus surgical treatment. The ICC was 0.99, expressing an excellent correlation between two measurements. The SEM was calculated at 0.22°C, the LoA at ?0.58°C and 0.64°C. The ?T cutoff point was ?0.07°C (sensitivity 80%; specificity 80%). These results show that thermography is a reliable and valid technique in the assessment of burn wound HP.

In burn wounds early discrimination between the different depths plays an important role in the treatment strategy. The remaining vasculature in the wound determines its healing potential. Non-invasive measurement tools that can identify the vascularization are therefore considered to be of high diagnostic importance. Thermography is a non-invasive technique that can accurately measure the temperature distribution over a large skin or tissue area, the temperature is a measure of the perfusion of that area. The aim of this study was to investigate the clinimetric properties (i.e. reliability and validity) of thermography for measuring burn wound depth. In a cross-sectional study with 50 burn wounds of 35 patients, the inter-observer reliability and the validity between thermography and Laser Doppler Imaging were studied. With ROC curve analyses the ΔT cut-off point for different burn wound depths were determined. The inter-observer reliability, expressed by an intra-class correlation coefficient of 0.99, was found to be excellent. In terms of validity, a ΔT cut-off point of 0.96°C (sensitivity 71%; specificity 79%) differentiates between a superficial partial-thickness and deep partial-thickness burn. A ΔT cut-off point of -0.80°C (sensitivity 70%; specificity 74%) could differentiate between a deep partial-thickness and a full-thickness burn wound. This study demonstrates that thermography is a reliable method in the assessment of burn wound depths. In addition, thermography was reasonably able to discriminate among different burn wound depths, indicating its potential use as a diagnostic tool in clinical burn practice.

Allergy testing is usually performed by exposing the skin to small quantities of potential allergens on the inner forearm and scratching the protective epidermis to increase exposure. After 15 minutes the dermatologist performs a visual check for swelling and erythema which is subjective and difficult for e.g. dark skin types. A small smart phone based thermo camera (FLIR One) was used to obtain quantitative images in a feasibility study of 17 patients Directly after allergen exposure on the forearm, thermal images were captured at 30 seconds interval and processed to a time lapse movie over 15 minutes. Considering the 'subjective' reading of the dermatologist as golden standard, in 11/17 pts (65%) the evaluation of dermatologist was confirmed by the thermo camera including 5 of 6 patients without allergic response. In 7 patients thermo showed additional spots. Of the 342 sites tested, the dermatologist detected 47 allergies of which 28 (60%) were confirmed by thermo imaging while thermo imaging showed 12 additional spots. The method can be improved with user dedicated acquisition software and better registration between normal and thermal images. The lymphatic reaction seems to shift from the original puncture site. The interpretation of the thermal images is still subjective since collecting quantitative data is difficult due to motion patient during 15 minutes. Although not yet conclusive, thermal imaging shows to be promising to improve the sensitivity and selectivity of allergy testing using a smart phone based camera.

During laparoscopic surgery, devices are require to either cut, ablate or coagulate tissue and veins with high precision and controlled lateral damage preferably in an one-for-all modality. The tissue interactions of 3 new treatment modalities were studied using special imaging techniques to obtain a better understanding the working mechanism in view of effective and safe application. The Plasmajet produces a high temperature ionized gas 'flame' directed to the tissue surface at the tip of a 4 mm diameter rigid hand piece. The Lumenis DUO CO2 laser enables endoscopic laser energy delivery through a 1 mm outer diameter flexible hollow waveguide. The 2 µm 'Thulium' laser is delivered by (standard) 400 µm diameter optical fiber. Thermal imaging and Schlieren techniques were used to assess the superficial ablative and coagulation effects these surgical instruments scanning at preset velocities and distances from the surface of biological tissues and phantoms . The CO2 was very effective in tissue ablation even at a distance up to 10 mm due to a very small diverging beam from the hollow waveguide. In contrast, the Thulium laser showed less ablation and increasing coagulation at larger distance to the tissue. The gas 'flame' of the Plasmajet spread the thermal energy over the surface for effective superficial ablation and coagulation. However, the pressure of the gas flow is substantial on the tissue surface creating turbulence and even indirect cooling. The specific ablation and coagulation effects of the three treatment modalities have to be appreciate and the effective and safe application will depend on the preference and skills of the surgeon

Background: It is generally believed that certain patient characteristics (e.g., Body Mass Index and age) predict difficulty of intravenous cannulation in children, but there is not much literature evaluating these risk factors. In this study, we investigated predictive factors for success rate at first attempt and time needed for intravenous cannulation. Methods/Materials: In a prospective cohort study, we observed characteristics of intravenous cannulations in pediatric patients at the operating room (n = 1083) and the outpatient care unit (n = 178) of a tertiary referral pediatric hospital. Time to successful intravenous cannulation, success at first attempt, and potential predictors for difficult cannulation (age, gender, skin color, BMI or weight-to-age z-score, the child being awake or anesthetized, operator profession and surgical specialty) were recorded. Regression models were constructed to find significant predictors. Results: Success at first attempt was 73% and 81%, respectively. In the operating room age, operator and surgical specialty were predictive for a successful first attempt and time to successful cannulation. No significant predictive factors were found for the outpatient care unit. BMI or weight-to-age was not related to difficult intravenous cannulation. Conclusions: This study shows that in one-fifth to one-third of the patients, intravenous cannulation required more than one attempt. It is difficult to predict with accuracy the difficulty of intravenous cannulation solely with easily obtainable patient characteristics.

Background and Objectives A key element in the Excimer Laser Assisted Non-occlusive Anastomosis (ELANA) technique is the retrieval of a disc (“flap”) of artery wall from the anastomosis by the laser catheter tip. We assessed if the flap retrieval rate could be optimized. Methods We used a specially designed in vitro model using rabbit aortas. We tested three essential elements of the technique: (1) laser energy (10, 13, 15, or 18 mJ), (2) pressure on the catheter (0, 0.1, 0.2, or 0.4 N), and (3) number of lasing episodes (1 or 2). We made 2,280 anastomoses using different combinations of settings. With a logistic regression model we assessed the influence of each parameter. Current clinical settings (10 mJ, 0.2 N, 1 episode) were reference categories. Results Flap retrieval rate using conventional settings was 86.7%, equivalent to earlier reported clinical data. A significantly higher flap retrieval appeared when laser energy was increased to 13 mJ (OR 3.0, 95% CI 1.8–4.8), 15 mJ (OR 3.2, 95% CI 1.9–5.3), and 18 mJ (OR 3.7, 95% CI 2.2–6.2). A second lasing episode also significantly increased flap retrieval (OR 2.1, 95% CI 1.4–3.0). However, if we increased energy to 15 or 18 mJ, the effect of a second laser episode was insignificant. When the catheter was pushed down with 0.4 N, flap retrieval decreased significantly in all subgroups (OR 0.07, 95% CI 0.04–0.14). Conclusion The flap retrieval of the ELANA anastomosis technique can be optimized to 100% by setting the laser energy at 15 mJ. However, safety studies are necessary before clinical application. A second lasing episode of 10 mJ is a good alternative to increase the flap retrieval. Moreover, the surgeon should be trained to apply not more than 0.2 N on the catheter. Lasers Surg. Med. 42:418-424, 2010. © 2010 Wiley-Liss, Inc.

Objective: Although tissue ablation by irreversible electroporation (IRE) has been characterized as nonthermal, the application of frequent repetitive high-intensity electric pulses has the potential of substantially heating the targeted tissue and causing thermal damage. This study evaluates the risk of possible thermal damage by measuring temperature development and distribution during IRE of porcine kidney tissue. Methods: The animal procedures were conducted following an approved Institutional Animal Ethics Committee protocol. IRE ablation was performed in 8 porcine kidneys. Of them, 4 kidneys were treated with a 3-needle configuration and the remaining 4 with a 4-needle configuration. All IRE ablations consisted of 70 pulses with a length 90 mu s. The pulse frequency was set at 90 pulses/min, and the pulse intensity at 1,500 V/cm with a spacing of 15 rum between the needles. The temperature was measured internally using 4 fiber-optic temperature probes and at the surface using a thermal camera. Results: For the 3-needle configuration, a peak temperature of 57 degrees C (mean = 49 +/- 10 degrees C, n = 3) was measured in the core of the ablation zone and 40 degrees C (mean = 36 +/- 3 degrees C, n = 3) at 1 cm outside of the ablation zone, from a baseline temperature of 33 +/- 1 degrees C. For the 4-needle configuration, a peak temperature of 79 degrees C (mean = 62 +/- 16 degrees C, n = 3) was measured in the core of the ablation zone and 42 degrees C (mean = 39 +/- 3 degrees C, n = 3) at 1 cm outside of the ablation zone, from a baseline of 35 +/- 1 degrees C. The thermal camera recorded the peak surface temperatures in the center of the ablation zone, reaching 31 degrees C and 35 degrees C for the 3- and 4-needle configuration IRE (baseline 22 degrees C). Conclusions: The application of repetitive high-intensity electric pulses during IRE ablation in porcine kidney causes a lethal rise in temperature within the ablation zone. Temperature monitoring should be considered when performing IRE ablation near vital structures. C) 2015 Elsevier Inc. All rights reserved

Hypothesis The mechanical and acoustic effects that occur during laser-assisted stapedotomy differ among KTP, CO2, and thulium lasers. Background Making a fenestration in stapedotomy with a laser minimizes the risk of a floating footplate caused by mechanical forces. Theoretically, the lasers used in stapedotomy could inflict mechanical trauma because of absorption in the perilymph, causing vaporization bubbles. These bubbles can generate a shock wave, when imploding. Methods In an inner ear model, we made a fenestration in a fresh human stapes with KTP, CO2, and thulium laser. During the fenestration, we performed high-speed imaging from different angles to capture mechanical effects. The sounds produced by the fenestration were recorded simultaneously with a hydrophone; these recordings were compared with acoustics produced by a conventional microburr fenestration. Results KTP laser fenestration showed little mechanical effects, with minimal sound production. With CO2 laser, miniscule bubbles arose in the vestibule; imploding of these bubbles corresponded to the acoustics. Thulium laser fenestration showed large bubbles in the vestibule, with a larger sound production than the other two lasers. Each type of laser generated significantly less noise than the microburr. The microburr maximally reached 95 ± 7 dB(A), compared with 49 ± 8 dB(A) for KTP, 68 ± 4 dB(A) for CO2, and 83 ± 6 dB(A) for thulium. Conclusion Mechanical and acoustic effects differ among lasers used for stapedotomy. Based on their relatively small effects, KTP and CO2 lasers are preferable to thulium laser.

The mechanism of action of the holmium laser lithotripsy is attributed to explosive expanding and imploding vapor bubbles in association with high-speed water jets creating high mechanical stress and cracking the stone surface. A good understanding of this mechanism will contribute to the improvement and the safety of clinical treatments. A new method has been developed to visualize the dynamics of mechanical effects and fluid flow induced by Holmium laser pulses around the fiber tip and the stone surface. The fiber tip was positioned near the surface of a stone on a slab of polyacrylamide gel submerged in water. The effects were captured with high speed imaging at 2000-10000 f/s. The dynamics of the pressure wave after the pulse could be visualized by observing the optical deformation of a fine line pattern in the background of the water container using digital subtraction software. This imaging technique provides a good understanding of the mechanical effects contributing to the effectiveness and safety of lithotripsy and can be used to study the optimal fiber shape and position towards the stone surface.

With new fiber systems available for 3 μm, Erbium lasers become more interesting for precise tissue ablation in a water environment enabling new application in e.g. dentistry. The dynamics of explosive bubble formation was investigated at 2.78 μm (Er,Cr;YSGG) and 2.94 μm (Er:YAG), in relation to energy (10-50 mJ), pulse length (20–150 μs) and fiber tip shape (flat or taper). The dynamics of exploding and imploding vapor bubbles were captured with high speed imaging (10 - 300 μs range). Increasing the pulse length and energy, the vapor bubble became more elongated with an opaque surface for flat tip fibers. Tapered fibers produced spherical vapor bubbles with an optically transparent surface expected to be more forceful for creating mechanical effects in both hard and soft tissues. There was no significant difference between bubbles formed at 2.78 μm (Er,Cr;YSGG) and 2.94 μm (Er:YAG).

The major problem of irrigation is the fluid motion within the confined geometry of the root canal : efficient dispersion of the liquid is difficult, conventional irrigation is limited due to the absence of turbulence over much of the canal volume, vapour lock may limit apical cleaning and disinfection, there is also a stagnation plane beyond the needle tip. The best way to improve irrigant penetration and biofilm removal is achieved by means of the agitation of the fluid. Today ultrasonic activation appears to be the best way to activate and potentiate irrigants among the present-day used means and marketed systems. Another way to activate irrigation solutions is the use of lasers: laser activated irrigation or photon-initiated acoustic streaming have been investigated. Based on present-day research it appears that the efficacy of laser activation (especially with Erbium lasers) can be more efficient thanks to the induction of specific cavitation phenomena and acoustic streaming. Other wavelengths are now explored to be used for laser activated irrigation.

For infants and neonates in an incubator vital signs, such as heart rate, breathing, skin temperature and blood oxygen saturation are measured by sensors and electrodes sticking to the skin. This can damage the vulnerable skin of neonates and cause infections. In addition, the wires interfere with the care and hinder the parents in holding and touching the baby. These problems initiated the search for baby friendly 'non-contact' measurement of vital signs. Using a sensitive color video camera and specially developed software, the heart rate was derived from subtle repetitive color changes. Potentially also respiration and oxygen saturation could be obtained. A thermal camera was used to monitor the temperature distribution of the whole body and detect small temperature variations around the nose revealing the respiration rate. After testing in the laboratory, seven babies were monitored (with parental consent) in the neonatal intensive care unit (NICU) simultaneously with the regular monitoring equipment. From the color video recordings accurate heart rates could be derived and the thermal images provided accurate respiration rates. To correct for the movements of the baby, tracking software could be applied. At present, the image processing was performed off-line. Using narrow band light sources also non-contact blood oxygen saturation could be measured. Non-contact monitoring of vital signs has proven to be feasible and can be developed into a real time system. Besides the application on the NICU non-contact vital function monitoring has large potential for other patient groups.

High-flow revascularization of the brain is hampered by the fact that temporary occlusion of a major brain artery, necessary to make the distal end-to-side anastomosis, may result in brain ischemia. The Excimer laser-assisted nonocclusive anastomosis technique circumvents this problem. After connecting donor and recipient vessels, an Excimer laser catheter, introduced by way of an artificial side branch, creates a hole at the anastomosis site. When the catheter is withdrawn, a round full-thickness portion of the recipient artery is removed. When the artificial side branch is occluded with a hemoclip the anastomosis is completed. The recipient vessel stays open during the procedure. In 90 patients a high-flow bypass was made. In 90% several types of extra-intracranial bypasses were created, and in 10% several types of intra-intracranial bypasses were created. Flow recordings by way of an ultrasound device intraoperatively and with a magnetic resonance (MR) flow program postoperatively show the bypasses to have a real “high flow” character. Complications related to this high-flow bypass procedure and ways to prevent them are presented.

Objectives. To study the influence of the electrosurgical generator on the vaporization efficacy during electrovaporization (EVAP) using different vaporization elements. Methods. Electrical properties of human prostatic (in vivo) and bovine myocardium (in vitro) tissue were measured under electroresection and electrovaporization conditions. The effective output power of four different generators (“old generation” Force 4 and Force 40 and “new generation” Force 300 and Force FX) was measured at different impedance loads. In vitro, the coagulation and vaporization capabilities of the electrosurgical generators in combination with resection and vaporization elements were studied on homogeneous tissue (bovine myocardium). Results. The electrical impedance of human prostatic tissue and bovine myocardium increases from 400 to 1000 Ω when coagulated. The effective output power of the old generation electrosurgical devices depends strongly on tissue impedance. This implies that working on already coagulated tissue using such devices is not well controlled and not reproducible. By contrast, new generation electrosurgical devices correct for the higher impedance of coagulated tissue, thus delivering constant output power and corresponding tissue effects. Conclusions. For an effective application of the EVAP technique, the use of a new generation impedance independent electrosurgical unit is highly recommended.

Background. High-flow extraintracranial bypass operation on the brain is a risky procedure because of the temporary occlusion of the intracranial portion of the internal carotid artery. We therefore developed a nonocclusive anastomosis technique in the experimental animal laboratory in 100 chronic and acute experiments in rabbits. Methods. In 40 patients we interposed a venous transplant between the external carotid artery or one of its branches and the intracranial portion of the internal carotid artery. During the construction of the distal anastomosis the recipient artery was not occluded. The donor vessel was stitched to the exterior of the recipient vessel and an Excimer laser catheter (Medolas GmbH, Amberg, Germany) was introduced by way of an artificial side branch. The tip of the laser catheter created a hole in the wall of the recipient artery just inside the anastomosis. The cut-out full-thickness portion of recipient vessel wall remained attached to the tip of the laser catheter by way of high vacuum suction and was removed together with the laser catheter. The artificial side branch was occluded with a hemostatic clip. No interruption of blood flow in the recipient artery was induced during the making of the anastomosis. Results. The procedure was well tolerated by the patients and a high patency rate was observed. Conclusions. The nonocclusive Excimer laser-assisted anastomosis technique is safe and yields a high longterm patency rate in neurosurgical patients. It cannot be excluded that there are indications for this method in coronary bypass surgery.

Color intensity projections (CIPs) has been employed to improve the accuracy and reduce the workload of interpreting a series of grayscale images by summarizing the grayscale images in a single color image. CIPs – which has been applied to grayscale images in angiography, 4D CT, nuclear medicine and astronomy – uses the hue, saturation and brightness of the color image to encode the summary information. In CIPs, when a pixel has the same value over the grayscale images, the corresponding pixel in the color image has the identical grayscale color. The arrival time of a signal at each pixel, such as the arrival time of contrast in angiography, is often encoded in the hue (red-yellow-green-light blue-blue-purple) of the corresponding pixel in the color image. In addition, the saturation and brightness of each pixel in the color image encodes the amplitude range and amplitude maximum of the corresponding pixel in the grayscale images. In previous applications of CIPs the hue has been limited to less than one cycle over the color image to avoid the aliasing due to a hue corresponding to more than one arrival time. However, sometimes in applications such as angiography and astronomy, in some instances the aliasing due to increasing the number of cycles of hue over the color image is tolerable as it increases the resolution of arrival time. Key to applying hue cycling effectively is interpolating several grayscale images between each pair of grayscale images. Ideally, the interpreter is allowed to adjust the amount of hue cycling in realtime to find the best setting for each particular CIPs image. CIPs with hue cycling should be a valuable tool in many fields where interpreting a series of grayscale images is required.

During clinical interventions objective and quantitative information of the tissue perfusion, oxygenation or temperature can be useful for the surgical strategy. Local (point) measurements give limited information and affected areas can easily be missed, therefore imaging large areas is required. In this study a LED based multispectral imaging system (MSI, 17 different wavelengths 370nm-880nm) and a thermo camera were applied during clinical interventions: tissue flap transplantations (ENT), local anesthetic block and during open brain surgery (epileptic seizure). The images covered an area of 20x20 cm, when doing measurements in an (operating) room, they turned out to be more complicated than laboratory experiments due to light fluctuations, movement of the patient and limited angle of view. By constantly measuring the background light and the use of a white reference, light fluctuations and movement were corrected. Oxygenation concentration images could be calculated and combined with the thermal images. The effectively of local anesthesia of a hand could be predicted in an early stage using the thermal camera and the reperfusion of transplanted skin flap could be imaged. During brain surgery, a temporary hyper-perfused area was witnessed which was probably related to an epileptic attack. A LED based multispectral imaging system combined with thermal imaging provide complementary information on perfusion and oxygenation changes and are promising techniques for real-time diagnostics during clinical interventions.

The Initial Systolic Time Interval (ISTI), obtained from the electrocardiogram and impedance cardiogram, is considered to be a measure for the time delay between the electrical and mechanical activity of the heart. This time delay is influenced by the sympathetic nerve system. Therefore, an observational study was performed in a group of patients (SCI) with spinal cord injuries. The relationship between the ISTI and the total heart cycle (RR-interval) was established by varying the RR-interval using an exercise stimulus to increase the heart rate. The slope of this relationship was observed to be significantly higher in the SCI-group as compared with a control group, although there was no difference in ISTI in the range of common heart rates during the test between the groups. This slope and the ISTI was observed to be significantly different in an acute patient having a recent spinal cord injury at a high level. Because of the variety in injury levels and incompleteness of the injuries further, more specific research is necessary to draw decisive conclusions with respect to the contribution of autonomic nervous control on the ISTI in SCI, although the present observations are notable.

We report a Ho:LLF MOPA pumped ZGP OPO based on Rotated Image Singly-Resonant Twisted RectAngle (RISTRA) cavity producing a pulse energy of 5 mJ at 100 Hz at 6.45 µm. Application in surgery is discussed.

Background. Arterial cannulation is a common anaesthetic procedure that can be challenging and time-consuming in small children. By visualizing the position of the radial artery, near-infrared vascular imaging systems (NIRVISs) might be of assistance in arterial cannulation. The present study evaluates the effectiveness of an NIRVIS in arterial cannulation in infants. Methods. An observational study was conducted in patients up to 3 yr old, undergoing arterial cannulation before cardiothoracic surgery. Arterial cannulation was performed as usual in 38 patients, and subsequently with the NIRVIS in 39 patients. Results. The time to successful cannulation was 547 s (171-1183) without and 464 s (174-996) with the NIRVIS (P=0.76) and the time to first flashback of blood was 171 s (96-522) and 219 s (59-447), respectively (P=0.38). There was a tendency in favour of the NIRVIS in success at first attempt: 12/38 and 7/39, respectively (P=0.29) and in the number of punctures: 6 (2-12) and 3 (1-7), respectively (P=0.10). Conclusions. The present study did not show a significant clinical improvement when NIR light was used during arterial cannulation in small children. There is a large difference between time to first flashback of blood and time to successful cannulation, indicating that inserting the cannula, and not localizing the artery, is the main difficulty in arterial cannulation in children. © 2012 The Author. Published by Oxford University Press on behalf of the British Journal of Anaesthesia. All rights reserved.

Optical parametric oscillators (OPOs) are attractive tools for research on tissue ablation upon infrared irradiation. Here, we report on the performance of several mid-infrared nonlinear crystals, namely type I and type II AgGaS2 (AGS) and type I CdSiP2 (CSP), used in synchronously-pumped OPOs tuned to a wavelength of 6.45 µm, coinciding with the amide II absorption band of proteins. CSP-based OPOs clearly exhibit better performance in comparison to AGS: First, the oscillation threshold with CSP is three (five) times lower than type II (type I) AGS. Second, the idler conversion efficiency is more favourable for CSP and allows reaching 27.5 mW of idler average power, while 13 and 6 mW are obtained with type II and type I AGS, respectively. Such performance makes CSP suitable for high power 6.45 µm surgical applications. Preliminary ablation experiments on liver tissues with our CSP-based OPO highlight the promising future of CSP in medical applications.

Introduction. This study aims to evaluate for the first time the value of visualizing veins by a prototype of a near-infrared (NIR) vascular imaging system for venipuncture in children. Methods. An observational feasibility study of venipunctures in children (0-6 years) attending the clinical laboratory of a pediatric university hospital during a period of 2 months without (n = 80) and subsequently during a period of 1 month with a prototype of an NIR vascular imaging system (n = 45) was conducted. Failure rate (ie, more than 1 puncture) and time of needle manipulation were determined. Results. With the NIR vascular imaging system, failure rate decreased from 10/80 to 1/45 ( P = .05) and time decreased from 2 seconds (1-10) to 1 second (1-4, P = .07). Conclusion . This study showed promising results on the value of an NIR vascular imaging system in facilitating venipunctures.

An objective method to measure the effectiveness of regional anesthesia can reduce time and unintended pain inflicted to the patient. A prospective observational study was performed on 22 patients during a local anesthesia before undergoing hand surgery. Two non-invasive techniques thermal and oxygenation imaging were applied to observe the region affected by the peripheral block and the results were compared to the standard cold sensation test. The supraclavicular block was placed under ultrasound guidance around the brachial plexus by injecting 20 cc Ropivacaine. The sedation causes a relaxation of the muscles around the blood vessels resulting in dilatation and hence an increase of blood perfusion, skin temperature and skin oxygenation in the lower arm and hand. Temperatures were acquired with an IR thermal camera (FLIR ThermoCam SC640). The data were recorded and analyzed with the ThermaCam TM Researcher and Matlab software. Narrow band spectral images were acquired at selected wavelengths with a CCD camera either combined with a Liquid Crystal Tunable Filter (420-730 nm) or a tunable hyper-wavelength LED light source (450-880nm). Concentration changes of oxygenated and deoxygenated hemoglobin in the dermis of the skin were calculated using the modified Lambert Beer equation. Both imaging methods showed distinct oxygenation and temperature differences at the surface of the skin of the hand with a good correlation to the anesthetized areas. A temperature response was visible within 5 minutes compared to the standard of 30 minutes. Both non-contact methods show to be more objective and can have an earlier prediction for the effectiveness of the anesthetic block.

Visualisation of the thermo dynamics of surgical coagulation devices like laser, diathermy and RFA devices in tissue are essential to get better understanding about the principles of operation of these devices. Thermo cameras have the ability to measure absolute temperatures. However, the visualization of temperature fields using thermal imaging has always been limited to the surface of a medium. We have developed a new strategy to look below the surface of biological tissue by viewing through a ZincSelenide window positioned alongside a block of tissue. When exposed from above with an energy source, the temperature distribution below the surface can be observed through the window. To obtain a close-up view, the thermo camera is enhanced with special macro optics. The thermo dynamics during tissue interaction of various electro surgery modes was studied in biological tissues to obtain a better understanding of the working mechanism. Simultaneously with thermal imaging, normal close-up video footage was obtained to support the interpretation of the thermal imaging. For comparison, temperature gradients were imaged inside a transparent tissue model using color Schlieren imaging. The new subsurface thermal imaging method gives a better understanding of interaction of thermal energy of surgical devices and contributes to the safety and the optimal settings for various medical applications. However, the technique has some limitations that have to be considered. The three imaging modalities showed to be both compatible and complementary showing the pro- and cons- of each modality.

The outcome of stapedotomy depends on several surgical steps. Using laser light, the ossicular chain can be handled and the oval window can be punctured with a non-touch method. Various lasers are being used or considered, however, it is not clear which settings and characteristics will contribute to optimal or adverse effects (vestibule damage and loss hearing frequencies). Using a unique high speed thermal imaging setup based on Schlieren techniques, the mechanical and thermal effects during laser stapedotomy were studied in an inner ear model consisting of human, fresh frozen stapes positioned on a liquid filled cavity in a gel cast. The cw KTP (532 nm), cw CO 2 (10.6 μm), cw Thulium (2.0 μm), pulsed Er,Cr;YSGG (2.78 μm) coupled to special fiber delivery systems were applied at typical clinical settings for comparison. The imaging techniques provided a good insight in the extent of heat conduction beneath the footplate and (explosive) vapour formation on both sides. For the pulsed laser modes, explosive vapour expansion can to be controlled with optimized pulse energies while for continuous wave lasers the thermal effects can be controlled with the pulse length and repetition rate. The fluence at the tip of the delivery system and the distance to the footplate has a major impact on the ablation effect. The pulsed IR lasers with fiber delivery show to be promising for a controlled stapedotomy.

To observe local variations in temperature, oxygenation and blood perfusion over time, four imaging systems were developed and compared: Two systems consisting of white broadband light source and a CCD camera in combination with a Liquid Crystal Tunable Filter, one in the visual domain, 420-730 nm, and one in the infrared domain, 650-1100 nm. Thirdly, a CCD camera in combination with a software controlled hyper-spectral light source consisting of a panel with 600 LEDs divided in 17 spectral groups in the range from 370 to 880 nm so that specific spectral distributions can be generated at high repetition rate (>1000 Hz) and, fourthly a standard IR thermal camera for comparison. From the acquired images at the selected wavelengths chromophores concentration images of oxy and deoxy hemoglobin can be calculated applying different algorithms. These imaging techniques were applied and compared for various clinical applications: Tumor demarcation, early inflammation, effectiveness of peripheral nerve block anesthesia, and localization of epileptic seizure. The relative changes in oxygenation and temperature could be clearly observed in good correlation with the physiological condition. The algorithms and data collection/processing can be optimized to enable a real-time diagnostic technique.

Multi-infusion systems are used frequently at intensive care units to administer several liquid therapeutic agents to patients simultaneously. By passively combining the separate infusion lines in one central line, the number of punctures needed to access the patient's body, is reduced. So far, the mutual influence between the different infusion lines is unknown. Although the flow properties of single infusion systems have been investigated extensively, only a few research groups have investigated the flow properties of multi-infusion systems. We showed in a previous study that applying multi-infusion can lead to fluctuations in syringe pump infusions, resulting in uncontrolled and inaccurate drug administration. This study presents a performance analysis of multi-infusion systems as used in the Neonatology Intensive Care Unit. The dynamics between multiple infusion lines in multi-infusion systems were investigated by simulation experiments of clinical conditions. A newly developed real-time spectral-photometric method was used for the quantitative determination of concentration and outflow volume using a deconvolution method of absorption spectra of mixed fluids. The effects for common clinical interventions were studied in detail. Results showed mutual influence between the different infusion lines following these interventions. This mutual influence led to significant volume fluctuations up to 50%. These deviations could result in clinically dangerous situations. A complete analysis of the multiinfusion system characteristics is recommended in further research to estimate both the presence and severity of potential risks in clinical use.

A practical near-IR blood vessel imaging system, the 'VascuLuminator', was developed to facilitate the puncturing of blood vessels for different procedures. Technical solutions were found for certain difficulties, such as obtaining a maximum image contrast by reducing the interference of IR light present in the surroundings. In phantom studies it was shown that the device is able to visualize blood vessels of different sizes to a clinically relevant maximum depth. In a preliminary clinical study, the use of the VascuLuminator resulted in decrease of the failure rate in blood withdrawal in young children from 13% to 2% and the laboratory technicians were satisfied with the practical application of the device. After this study, the effectiveness of the VascuLuminator was investigated to facilitate arterial cannulation in a group of children undergoing cardiac surgery. In an ongoing study, 71 children up to 3 years of age were included and time of arterial cannulation, number of punctures and puncture site were recorded. In 38 patients, cannulation was performed without the VascuLuminator and in 33 patients with VascuLuminator by pediatric anesthesiologists. The initial results do not show significant differences in time and in number of punctures with and without the use of the VascuLuminator. However, the VascuLuminator was able to visualize the arteries in most cases. In 11 of the 33 cases, the artery was located by using only the near-infrared image was used, without palpating for a pulse or knowledge of anatomical landmarks. Further clinical studies are needed to identify the patients groups that will benefit the most from VascuLuminator-assisted vessel punctures.

Tissue oxygenation imaging is a promising diagnostics tool to study the changes and dynamics of tissue perfusion reflecting pathologic and/or physiologic conditions of tissue. In clinical settings, imaging of local oxygenation or blood perfusion variations can be useful for e.g. detection of skin cancer, detection of early inflammation, effectiveness of peripheral nerve block anesthesia, study of the process of wound healing or localization of the cerebral area causing an epileptic attack. In this study, two oxygenation imaging methods based on multi-spectral techniques were evaluated: one system consisting of a CCD camera in combination with a Liquid Crystal Tunable Filter (420 - 730 nm or 650-1100 nm) and a broad band (white) light source, while the second system was a CCD camera in combination with a tunable multispectral LED light source (450-890nm). By collecting narrowband images at selected wavelengths, concentration changes of the different chromophores at the surface of the tissue (e.g. dO2Hb, dHHb and dtHb) can be calculated using the modified Lambert Beer equation. Two analyzing methods were used to calculate the concentration changes this to reduce the errors caused by movement of the tissue. In vivo measurements were obtained during skin oxygen changes induced by temporary arm clamping to validate the methods and algorithms. Functional information from the tissue surface was collected, in non-contact mode, by imaging the hemodynamic and oxygenation changes just below that surface. Both multi-spectral imaging techniques show promising results for detecting dynamic changes in the hemoglobin concentrations. The algorithms need to be optimized and image acquisition and processing needs to be developed top real time for practical clinical applications.

Electrosurgical equipment used during surgery generate smoke consisting of particles, vapor, aerosols and potentially harmful biological agents. Smoke evacuation systems are used more commonly and various types are available. A special image enhancement technique was used to study the behavior of surgical smoke and the effectiveness of smoke evacuation systems. Three different smoke evacuation systems were investigated. Rapid vac (Valleylab Boulder CO) The Buffalo silent whisper turbo (Buffalo, NY) ERBE IES 300 ( Tübingen, Germany) A back scatter illumination technique in combination with a high speed camera was applied to image the dynamics of a smoke plume generated by vaporizing a homogenous meat paste irradiated with the beam of a 10 W cw CO 2 laser moving at a constant speed. The three different smoke evacuation systems with their individual nozzles, were held 2 cm above the surface of the meat paste and were switched on and off at fixed intervals to mimic a clinical situation. For images analysis, software was developed to count 'smoke pixels' in the video frames as a quantification tool. For the observer's eye, there were no differences between the systems. However, images quantification showed significantly less 'smoke' for the Buffalo system. It is expected that the performance in a clinical situation is also influenced by additional conditions like nozzle design, airflow and noise level. Noise levels were measured at the tip of the nozzle, 80 cm from the tip, 140 cm from the tip. The Buffalo system is the loudest system at every distance measured.

Laser photocoagulation of myocardium is an alternative to surgical resection in the treatment of drug resistant ventricular tachycardia. In certain areas, of the heart, however, bare fibre delivery of laser energy involves a risk of unintentional damage to nearby structures. The purpose of the study was to determine whether Nd-YAG laser irradiation, delivered with the transparent contact probe, would produce adequate laser photocoagulation of the canine myocardium in comparison to bare fibre delivery of the laser energy. In nine mongrel dogs, continuous wave Nd-YAG laser irradiation with and without a transparent contact probe was directed at the epicardium. Pulse power was 10, 15 and 20 W, pulse duration 5, 7 and 10 s, and spot size was 1 mm. A total of 178 lesions were analyzed microscopically. After a 200 J pulse energy delivered by the contact probe, the lesion depth was 4.9±0.5 mm (mean±s.d.), which is usually adequate to ablate arrhythmia sites. Bare fibre delivery of laser energy did not produce deeper lesions. There was no difference between the bare fibre and the transparent probe in the occurrence of major arrhythmias (4/86 bare fibre, 3/92 transparent probe). We conclude that the transparent contact probe allows safe and effective laser irradiation of sites of origin of ventricular arrhythmias.

This study describes noninvasive noncontact methods to acquire and analyze functional information from the skin. Multispectral images at several selected wavelengths in the visible and near infrared region are collected and used in mathematical methods to calculate concentrations of different chromophores in the epidermis and dermis of the skin. This is based on the continuous wave Near Infrared Spectroscopy method, which is a well known non-invasive technique for measuring oxygenation changes in the brain and in muscle tissue. Concentration changes of hemoglobin (dO 2 Hb, dHHb and dtHb) can be calculated from light attenuations using the modified Lambert Beer equation. We applied this technique on multi-spectral images taken from the skin surface using different algorithms for calculating changes in O 2 Hb, HHb and tHb. In clinical settings, the imaging of local oxygenation variations and/or blood perfusion in the skin can be useful for e.g. detection of skin cancer, detection of early inflammation, checking the level of peripheral nerve block anesthesia, study of wound healing and tissue viability by skin flap transplantations. Images from the skin are obtained with a multi-spectral imaging system consisting of a 12-bit CCD camera in combination with a Liquid Crystal Tunable Filter. The skin is illuminated with either a broad band light source or a tunable multi wavelength LED light source. A polarization filter is used to block the direct reflected light. The collected multi-spectral imaging data are images of the skin surface radiance; each pixel contains either the full spectrum (420 - 730 nm) or a set of selected wavelengths. These images were converted to reflectance spectra. The algorithms were validated during skin oxygen saturation changes induced by temporary arm clamping and applied to some clinical examples. The initial results with the multi-spectral skin imaging system show good results for detecting dynamic changes in oxygen concentration. However, the optimal algorithm needs to be determined. Multi-spectral skin imaging shows to be a promising technique for various clinical applications were the local distribution of oxygenation is of major importance.