Search

Background: Aim of this study was to assess the accuracy of ventricular septal defects (VSD) using high pitch computed tomography angiography (CTA) of the chest in children below 1 year of age, compared to the intraoperative findings and echocardiography., Methods: Out of 154 patients that underwent Dual-Source CTA of the chest using a high-pitch protocol at low tube voltages (70-80 kV), 55 underwent surgical repair of a VSD (median age 8 days, range 1-348 days). The margins of the VSDs and their relation to the surrounding structures were reproduced by en-face views using multiplanar reformations (MPR). Absolute diameter, normalized area and relative area compared to the aortic valve annulus were used for discrimination between restrictive and non-restrictive defects. Localization was classified into four subtypes. The results were compared to two-dimensional echocardiography and intraoperative findings., Results: Median absolute size of VSDs did not differ significantly between CTA-measurements (10.8 mm, range 2.8-18.1 mm) and intraoperative findings (12.0 mm, 3.0-25.0 mm, p = 0.09). Echocardiographic values were significantly lower (9.6 mm, 3.0-18.5 mm, both p < 0.01). The classification of the location and orientation matched the intraoperative situs in 96.4% of all cases using CT and in 87.3% using echocardiography. Echocardiography missed the relation to valves in 11% of all cases. Pre-interventional sensitivity and specificity for detection of a VSD were 97.2/98.9% compared to echocardiography. Median radiation dose was 0.32 mSv (range 0.12-2.00 mSv) and differed significantly between second and third generation Dual-Source CT (0.43 vs. 0.22 mSv, p = 0.003)., Conclusion: Size and subtype of VSDs can be accurately assessed by CTA of the chest in patients with complex congenital heart defects at a very low radiation dose., (Copyright © 2019 Society of Cardiovascular Computed Tomography. Published by Elsevier Inc. All rights reserved.)

Objective: To evaluate the image quality and diagnostic accuracy of very low-dose computed tomography (CT) angiography (CTA) for the evaluation of coronary artery stenosis., Background: Iterative reconstruction (IR) has shown to substantially reduce image noise and hence permit the use of very low-dose data acquisition protocols in coronary CTA., Methods: Fifty symptomatic patients with an intermediate likelihood for coronary artery disease underwent coronary CTA (heart rate: 59 ± 5 bpm, prospectively ECG-triggered axial acquisition, 100 kV, 160 mAs, 2 × 128 × 0.6 mm collimation, 60 mL contrast, 6 mL/s) prior to invasive coronary angiography. CTA images were reconstructed using both standard filtered back projection (FBP) and a raw data-based IR algorithm [Sinogram Affirmed Iterative Reconstruction (SAFIRE), Siemens Healthcare]. Subjective image quality (four-point Likert scale from 0 = non-diagnostic to 3 = excellent image quality), image noise, signal-to-noise ratio (SNR), contrast-to-noise ratio (CNR), as well as the presence of coronary stenosis >50% were independently determined by two observers., Results: The mean dose-length product was 46.8 ± 3.5 mGy cm (estimated effective dose 0.66 ± 0.05 mSv). IR led to significantly improved objective image quality compared with FBP (image noise: 41 ± 12 vs. 49 ± 11 HU, P < 0.0001; CNR: 16 ± 8 vs. 12 ± 4, P < 0.0001; SNR: 13 ± 7 vs. 10 ± 3, P < 0.0001). Four coronary segments were not evaluable on FBP data, whereas all segments showed diagnostic image quality with IR. To detect significant coronary stenosis, sensitivity, specificity, positive predictive value, and negative predictive value were 69% (11/16), 97% (175/180), 69% (11/16), and 97% (175/180) per vessel with FBP data sets, respectively. With IR data sets, the corresponding values were 81% (13/16), 97% (178/184), 68% (13/19), and 98% (178/181). These differences were not statistically significant (P = 0.617)., Conclusions: Raw data-based IR significantly improves image quality in very low-dose prospectively ECG-triggered coronary dual-source CTA when compared with standard reconstruction using FBP., (Published on behalf of the European Society of Cardiology. All rights reserved. © The Author 2014. For permissions please email: journals.permissions@oup.com.)

Background: Low tube voltage reduces radiation exposure in coronary CT angiography (CTA). Using 70 kVp tube potential has so far not been possible because CT systems were unable to provide sufficiently high tube current with low voltage., Objective: We evaluated feasibility, image quality (IQ), and radiation dose of coronary CTA using a third-generation dual-source CT system capable of producing 450 mAs tube current at 70 kVp tube voltage., Methods: Coronary CTA was performed in 26 consecutive patients with suspected coronary artery disease, selected for body weight <100 kg and heart rate <60 beats/min. High-pitch spiral acquisition was used. Filtered back projection (FBP) and iterative reconstruction (IR) algorithms were applied. IQ was assessed using a 4-point rating scale (1 = excellent, 4 = nondiagnostic) and objective parameters., Results: Mean age was 62 ± 9 years (46% males; mean body mass index, 27.7 ± 3.8 kg/m(2); mean heart rate, 54 ± 5 beats/min). Mean dose-length product was 20.6 ± 1.9 mGy × cm; mean estimated effective radiation dose was 0.3 ± 0.03 mSv. Diagnostic IQ was found in 365 of 367 (FBP) and 366 of 367 (IR) segments (P nonsignificant). IQ was rated "excellent" in 53% (FBP) and 86% (IR) segments (P = .001) and "nondiagnostic" in 2 (FBP) and 1 segment (IR) (P nonsignificant). Mean IQ score was lesser in FBP vs IR (1.5 ± 0.4 vs 1.1 ± 0.2; P < .001). Image noise was lower in IR vs FBP (60 ± 10 HU vs 74 ± 8 HU; P < .001)., Conclusion: In patients <100 kg and with a regular heart rate <60 beats/min, third-generation dual-source CT using high-pitch spiral acquisition and 70 kVp tube voltage is feasible and provides both robust IQ and very low radiation exposure., (Copyright © 2014 Society of Cardiovascular Computed Tomography. Published by Elsevier Inc. All rights reserved.)

Background: Dual-source CT offers accurate depiction of cardiac structures in children with congenital heart disease. For cardiac CT, optimal enhancement of the cardiovascular structures is essential. There is considerable controversy about the administration of contrast medium (CM) in infants and small children, with either a power injector or a manual (hand) injection., Objective: The aim of this study was to compare image quality with power injection of CM (study group) and manual injection (control group)., Methods: Thirty-four patients (study group, 6.8 ± 9.6 months and control group, 4.6 ± 8.9 months, nonrandomized) underwent dual-source CT angiography of the chest using a prospective electrocardiography-triggered high-pitch spiral mode (pitch, 3.4; 80 kV). In the study group (17 patients), a power injector was used, and in the control group (17 patients, historical group), manual CM injection had been performed. To assess image quality, both subjective and objective parameters were evaluated independently by 2 experienced radiologists., Results: Subjective overall image quality, signal-to-noise ratio, and contrast-to-noise ratio were significantly higher using power injection compared with manual injection (P < .05). However, depiction of cardiovascular structures did not differ significantly between both groups in all evaluated regions except the superior vena cava and the coronary arteries., Conclusion: In infants and small children with congenital heart disease, both manual and power injector protocols allowed for diagnostic imaging of cardiac and extracardiac structures. However, image quality and vascular attenuation were superior using a power injector., (Copyright © 2014 Society of Cardiovascular Computed Tomography. Published by Elsevier Inc. All rights reserved.)

Background: Different iterative reconstruction (IR) techniques compensate increased noise from lower tube current-time product settings, yet the differences between IR settings remain unclear., Objective: Aim of this study was to test whether different IR settings have a clinically relevant influence on image quality and on the diagnostic accuracy of low-dose CT angiography in patients with a stent., Methods: Forty-two patients with 73 coronary stents were prospectively enrolled. Data were acquired with dual-source CT, and images were reconstructed with standard filtered back projection (FBP) and raw data-based IR with different settings (I3, I4, I5). Quantitative parameters, including CT-attenuation, noise, signal-to-noise ratio, contrast-to-noise ratio, as well as the presence of in-stent stenosis > 50% were determined. All patients had invasive angiography as reference standard., Results: Mean effective dose was 0.32 ± 0.02 mSv. Image noise decreased significantly compared with FBP (I3 = 29%; I4 = 38% and I5 = 45%), whereas signal-to-noise and contrast-to-noise ratios increased significantly (all IR settings P < .01). Subjective image quality was superior with all IR settings (P < .01). FBP sensitivity, specificity, positive predictive value, and negative predictive value were 83%, 71%, 36%, and 96% per stent compared with 100%, 76%, 44%, and 100%, respectively, in IR reconstructions independent of the IR setting applied., Conclusion: In low-dose coronary CT angiography, higher IR settings significantly improved subjective and objective image quality but had no effect on accuracy., (Copyright © 2013 Society of Cardiovascular Computed Tomography. Published by Elsevier Inc. All rights reserved.)

Objectives: The purpose of this study was to evaluate the image quality and diagnostic accuracy of very low-dose, dual-source computed tomography (DSCT) angiography for the evaluation of coronary stents., Background: Iterative reconstruction (IR) leads to substantial reduction of image noise and hence permits the use of very low-dose data acquisition protocols in coronary computed tomography angiography., Methods: Fifty symptomatic patients with 87 coronary stents (diameter 3.0 ± 0.4 mm) underwent coronary DSCT angiography (heart rate, 60 ± 6 beats/min; prospectively electrocardiography-triggered axial acquisition; 80 kV, 165 mA, 2 × 128 × 0.6-mm collimation; 60 ml of contrast at 6 ml/s) before invasive coronary angiography. DSCT images were reconstructed using both standard filtered back projection and a raw data-based IR algorithm (SAFIRE, Siemens Healthcare, Forchheim, Germany). Subjective image quality (4-point scale from 0 [nondiagnostic] to 3 [excellent image quality]), image noise, contrast-to-noise ratio as well as the presence of in-stent stenosis >50% were independently determined by 2 observers., Results: The median dose-length product was 23.0 (22.0; 23.0) mGy · cm (median estimated effective dose of 0.32 [0.31; 0.32] mSv). IR led to significantly improved image quality compared with filtered back projection (image quality score, 1.8 ± 0.6 vs. 1.5 ± 0.5, p < 0.05; image noise, 70 Hounsfield units [62; 80 Hounsfield units] vs. 96 Hounsfield units [82; 113 Hounsfield units], p < 0.001; contrast-to-noise ratio, 11.0 [9.6; 12.4] vs. 8.0 [6.2; 9.3], p < 0.001). To detect significant coronary stenosis in filtered back projection reconstructions, the sensitivity, specificity, positive predictive value, and negative predictive value were 97% (32 of 33), 53% (9 of 17), 80% (32 of 40), and 90% (9 of 10) per patient, respectively; 89% (43 of 48), 79% (120 of 152), 57% (42 of 74), and 96% (121 of 126) per vessel, respectively; and 85% (12 of 14), 69% (51 of 73), 32% (11 of 34), and 96% (51 of 53) per stent, respectively. In reconstructions obtained by IR, the corresponding values were 100% (33 of 33), 65% (11 of 17), 85% (33 of 39), and 100% (11 of 11) per patient, respectively; 96% (46 of 48), 84% (129 of 152), 66% (47 of 71), and 98% (127 of 129) per vessel, respectively; and 100% (14 of 14), 75% (55 of 73), 44% (14 of 32), and 100% (55 of 55) per stent, respectively. These differences were not significant., Conclusions: In selected patients, prospectively electrocardiography-triggered image acquisition with 80-kV tube voltage and low current in combination with IR permits the evaluation of patients with implanted coronary artery stents with reasonable diagnostic accuracy at very low radiation exposure., (Copyright © 2013 American College of Cardiology Foundation. Published by Elsevier Inc. All rights reserved.)

Objectives: We evaluated the potential of prospectively ECG-triggered high-pitch spiral acquisition with low tube voltage and current in combination with iterative reconstruction to achieve coronary CT angiography with sufficient image quality at an effective dose below 0.1 mSv., Methods: Contrast-enhanced coronary dual source CT angiography (2 × 128 × 0.6 mm, 80 kV, 50 mAs) in prospectively ECG-triggered high-pitch spiral acquisition mode was performed in 21 consecutive individuals (body weight <100 kg, heart rate ≤60/min). Images were reconstructed with raw data-based filtered back projection (FBP) and iterative reconstruction (IR). Image quality was assessed on a 4-point scale (1 = no artefacts, 4 = unevaluable)., Results: Mean effective dose was 0.06 ± 0.01 mSv. Image noise was significantly reduced in IR (128.9 ± 46.6 vs. 158.2 ± 44.7 HU). The mean image quality score was lower for IR (1.9 ± 1.1 vs. 2.2 ± 1.0, P < 0.0001). Of 292 coronary segments, 55 in FBP and 40 in IR (P = 0.12) were graded "unevaluable". In patients with a body weight ≤75 kg, both in FBP and in IR, the rates of fully evaluable segments were significantly higher in comparison to patients >75 kg., Conclusions: Coronary CT angiography with an estimated effective dose <0.1 mSv may provide sufficient image quality in selected patients through the combination of high-pitch spiral acquisition and raw data-based iterative reconstruction.

Background: Coronary computed tomography (CT) angiography can be associated with high radiation exposure. Reduction of tube voltage from 120 kV to 100 kV can reduce the dose by up to 40%, but it also increases image noise., Objective: We aimed to find a patient-specific predictor of image noise to determine the use of reduced tube voltage., Methods: Contrast-enhanced coronary dual-source CT angiography data sets [prospectively electrocardiogram (ECG)-triggered axial and retrospectively ECG-gated spiral acquisition, rotation of 280 milliseconds, 2 × 128 × 0.6 mm collimation, 100 kV, 320 mAs] of 165 patients (age, 54 ± 13 years) for the detection of coronary artery stenoses were analyzed. Image noise was measured in the aortic root. Influence of body weight, height, body mass index, thoracic cross sectional area, as well as the area of the thoracic solid tissue were analyzed., Results: Mean image noise in the aorta was 35.1 ± 8.9 HU. Mean dose length product was 207 ± 184 cm · cGy with an average effective dose of 2.9 ± 2.6 mSv. The patient cohort was divided into tertiles according to image noise. Numerous parameters, including BMI and body weight, were significantly different between the highest and lowest tertiles. In multivariable regression analysis, the area of the thoracic solid tissue was the only independent predictor of image noise (P < 0.0001)., Conclusions: The area of the thoracic solid tissue at the level of the aortic root predicts image noise and may hence be used for the decision to reduce tube voltage from 120 kV to 100 kV., (Copyright © 2013 Society of Cardiovascular Computed Tomography. Published by Elsevier Inc. All rights reserved.)

Background: We compared the interobserver variability concerning the detection of calcified and non-calcified plaque in two different low-dose and standard retrospectively gated protocols for coronary CTA., Methods: 150 patients with low heart rates and less than 100 kg body weight were randomised and examined by contrast-enhanced dual-source CT coronary angiography (100 kV, 320 mAs). 50 patients were examined with prospectively ECG-triggered axial acquisition, 50 patients with prospectively ECG-triggered high pitch spiral acquisition, and 50 patients using spiral acquisition with retrospective ECG gating. Two investigators independently analysed the datasets concerning the presence of calcified and non-calcified plaque on a per-segment level., Results: Mean effective dose was 1.4 ± 0.2 mSv for axial, 0.8 ± 0.07 mSv for high-pitch spiral, and 5.3 ± 2.6 mSV for standard spiral acquisition (P < 0.0001). In axial acquisition, interobserver agreement concerning the presence of atherosclerotic plaque was achieved in 650/749 coronary segments (86.8%). In high-pitch spiral acquisition, agreement was achieved in 664/748 segments (88.8%, n.s.). In standard spiral acquisition, agreement was achieved in 672/738 segments (91.0%, P < 0.0001). Interobserver agreement was significantly higher for calcified than for non-calcified plaque in all data acquisition modes., Conclusion: Low-dose coronary CT angiography permits the detection of coronary atherosclerotic plaque with good interobserver agreement., Key Points: • Low-dose CT protocols permit coronary plaque detection with good interobserver agreement. • Image noise is a major predictor of interobserver variability. • Interobserver agreement is significantly higher for calcified than for non-calcified plaque.

Background: Coronary CT angiography allows visualization of the coronary arteries. However, motion artifact can impair delineation of the coronary artery lumen and detection of coronary artery stenoses., Objective: We investigated the influence of heart rate and the segment of the cardiac cycle during which images are reconstructed on the occurrence of motion artifacts., Methods: We evaluated coronary CT angiography datasets obtained by 64-slice dual-source CT in 100 consecutive patients. Data were reconstructed at 13 time instants during the cardiac cycle and evaluated for the presence of motion artifact., Results: Mean heart rate was 66±14 beats/min. Overall, 98 of 100 patients had evaluable datasets. For heart rates ≤60 beats/min, optimal image quality was uniformly found during late diastole (100% of cases with evaluable image quality during a time window between 65% and 75% of the cardiac cycle). With increasing heart rates, images reconstructed during late systole more frequently provided best image quality. However, image reconstruction could not be restricted to a systolic time period. To achieve evaluable image quality in 95% of cases, data acquired between 25% and 75% of the cardiac cycle had to be available for patients with heart rates >60 beats/min., Conclusion: Dual-source CT provides high image quality across a wide range of heart rates. Although data acquisition may be limited to diastole for patients with heart rates ≤60 beats/min, the availability of data acquired both during systole and diastole is necessary for patients with higher heart rates., (Copyright © 2012 Society of Cardiovascular Computed Tomography. Published by Elsevier Inc. All rights reserved.)

Objectives: To evaluate radiation dose levels in patients undergoing spiral coronary computed tomography angiography (CTA) on a dual-source system in clinical routine., Methods: Coronary CTA was performed for 56 patients with electrocardiogram-triggered tube current modulation (TCM) and heart-rate (HR) dependent pitch adaptation. Individual Monte Carlo (MC) simulations were performed for dose assessment. Retrospective simulations with constant tube current (CTC) served as reference. Lung tissue was segmented and used for organ and effective dose (ED) calculation., Results: Estimates for mean relative ED was 7.1 ± 2.1 mSv/100 mAs for TCM and 12.5 ± 5.3 mSv/100 mAs for CTC (P < 0.001). Relative dose reduction at low HR (≤60 bpm) was highest (49 ± 5%) compared to intermediate (60-70 bpm, 33 ± 12%) and high HR (>70 bpm, 29 ± 12%). However lowest ED is achieved at high HR (5.2 ± 1.5 mSv/100 mAs), compared with intermediate (6.7 ± 1.6 mSv/100 mAs) and low (8.3 ± 2.1 mSv/100 mAs) HR when automated pitch adaptation is applied., Conclusions: Radiation dose savings up to 52% are achievable by TCM at low and regular HR. However lowest ED is attained at high HR by pitch adaptation despite inferior radiation dose reduction by TCM., Key Points: • Monte Carlo simulations allow for individual radiation dose calculations. • ECG-triggered tube current modulation (TCM) can effectively reduce radiation dose. • Slow and regular heart rates allow for highest dose reductions by TCM. • Adaptive pitch accounts for lowest radiation dose at high heart rates. • Women receive higher effective dose than men undergoing spiral coronary CT-angiography.

Background: Aim of this study was to compare DNA double-strand breaks (DSBs) in blood lymphocytes of patients undergoing high-pitch helical, low-pitch helical and sequential coronary CT angiography., Methods and Results: 66 patients were examined with various scan protocols and modes (low-pitch helical scan: 100-120 kV, 320-438 mAs/rot, pitch 0.18-0.39, with or without ECG-pulsing, n=35; prospectively ECG-triggered high-pitch helical scan: 100-120 kV, 320-456 mAs/rotation, pitch 3.2-3.4, n=19; prospectively ECG-triggered sequential scan: 100-120 kV, 150-300 mAs or 320-370 mAs/rotation, n=12) either using a 64-slice or 128-slice dual-source CT or a 128-slice single source CT scanner. Blood samples were obtained before and 30 min after CT and DSBs were analyzed in isolated lymphocytes using γ-H2AX immunofluorescence microscopy. A significant increase of DSBs was measurable 30 min after CTA (range 0.01-0.71/cell). CT induced DSBs showed a significant correlation with the estimated effective dose (ρ=0.90, p<0.00001). Both prospectively ECG-triggered sequential (0.10 DSBs/cell, 176 mGy cm, p<0.00001) and high-pitch helical scan protocols (0.03 DSBs/cell, 109 mGy cm, p<0.00001) led to a significant reduction of median DLP and DSB levels compared to low-pitch helical scans (0.34 DSBs/cell, 828 mGy cm). A reduction of the tube voltage resulted in significantly lower whereas additional calcium scoring resulted in elevated DLP and DNA damages (p<0.05 each)., Conclusion: In coronary CTA, data acquisition protocols have a significant influence on the X-ray induced DSB levels. Using γ-H2AX immunofluorescence microscopy different scan modes in different CT generations can be compared concerning their biological impact., (Copyright © 2011 Elsevier Ireland Ltd. All rights reserved.)

Objectives: We sought to evaluate the diagnostic accuracy of a new prospectively electrocardiogram (ECG)-triggered high-pitch scan mode for coronary computed tomography angiography (CTA), which allows an effective dose of less than 1 mSv., Background: Coronary CTA provides increasingly reliable image quality, but the associated radiation exposure can be high., Methods: Seventy-five patients with suspected coronary artery disease and in sinus rhythm were screened for participation. After exclusion of 25 patients for body weight >100 kg or failure to lower heart rate to ≤ 60 beats/min, 50 patients were studied by prospectively ECG-triggered high-pitch spiral computed tomography (CT). Coronary CTA was performed using a dual-source CT system with 2 × 128 × 0.6-mm collimation, 0.28-s rotation time, a pitch of 3.4, 100-kVp tube voltage, and current of 320 mA. Data acquisition was prospectively triggered at 60% of the R-R interval and completed within 1 cardiac cycle. Diagnostic accuracy for detection of coronary artery stenoses ≥ 50% diameter stenosis was determined by comparison to invasive coronary angiography. Per-patient diagnostic performance was the primary form of analysis., Results: In all 50 patients (34 males, 59 ± 12 years of age), imaging was successful. For the detection of 16 patients with at least 1 coronary artery stenosis, CT demonstrated a sensitivity of 100% (95% confidence interval [CI]: 79% to 100%) and specificity of 82% (95% CI: 65% to 93%). The positive predictive value was 72% (95% CI: 49% to 89%) and the negative predictive value was 100% (95% CI: 87% to 100%). Sensitivity was 100% (95% CI: 88% to 100%) and specificity was 94% (95% CI: 89% to 97%) on a per-vessel basis. Per-segment sensitivity was 92% (95% CI: 80% to 97%), and specificity was 98% (95% CI: 96% to 98%). Mean dose-length product for coronary CTA was 54 ± 6 mGy · cm, the effective dose was 0.76 ± 0.08 mSv (0.64 to 0.95 mSv)., Conclusions: In nonobese patients with a low and stable heart rate, prospectively ECG-triggered high-pitch spiral coronary CTA provides high diagnostic accuracy for the detection of coronary artery stenoses., (Copyright © 2011 American College of Cardiology Foundation. Published by Elsevier Inc. All rights reserved.)

Aims: To compare in vivo DNA lesions induced during helical and sequential coronary computed tomography angiography (CTA) and to evaluate the effect of CT parameters on double-strand break (DSB) levels., Methods: Thirty-six patients were examined with various CT protocols and modes (helical scan, n = 27; sequential scan, n = 9) either using a 64-slice dual-source or a 128-slice CT system. Blood samples were obtained before and 30 min after CT. Lymphocytes were isolated, stained against the phosphorylated histone variant γ-H2AX, and DSBs were visualised by using fluorescence microscopy., Results: DSB yields 30 min after CTA ranged from 0.04 to 0.71 per cell and showed a significant correlation to DLP (ρ = 0.81, p < 0.00001). Median DSB yield and median DLP were significantly lower after sequential compared to helical CT examinations (0.11 vs. 0.37 DSBs/cell and 249 vs. 958 mGy cm, p < 0.00001). Additional calcium scoring led to an increase in DLP (p = 0.15) and DSB levels (p = 0.04). DSB levels normalised to the DLP showed a significant correlation to the attenuation of the blood (ρ = 0.53, p = 0.01) and a negative correlation to the body mass index of the patients (ρ = -0.37, p = 0.06)., Conclusion: γ-H2AX immunofluorescence microscopy allows one to determine dose-related effects on x-ray-induced DSB levels and to consider individual factors which cannot be monitored by physical dose measurements.

Objective: To evaluate staged low-dose approaches for coronary CT angiography (CTA) in which a standard sequence was added if the low-dose sequence did not allow reliable rule-out of coronary stenosis., Patients and Methods: A total of 176 consecutive patients referred for dual-source CTA were randomized to three protocols: group 1 using prospective ECG-triggering (100 kV, 330 mAs), group 2 a retrospectively gated "MinDose" sequence (100 kV, 330 mAs) and group 3 a standard spiral sequence (120 kV, 400 mAs). If image quality in low-dose groups 1 or 2 was non-diagnostic, an additional standard CT examination (as in group 3) was performed., Results: Non-diagnostic image quality was found in 11/56, 4/55, and 2/65 patients (46/896, 4/880 and 3/1,040 coronary segments) in groups 1, 2 and 3, respectively. Median (interquartile ranges) volumes of contrast material, CTDI(vol), DLP and effective dose for low-dose groups 1 and 2 and for standard group 3 were 92.5 (11.3), 75.0 (2.5) and 75.0 (9.0) ml; 8.0 (1.4), 16.8 (4.8) and 48.1 (14.2) mGy; 108.0 (27.3), 246.0 (93.0) and 701.0 (207.8) mGy cm; and 1.5 (0.4), 3.4 (1.3) and 9.8 (2.9) mSv, respectively., Conclusion: A staged coronary CTA protocol with an initial low-dose approach and addition of a standard sequence--should image quality be too low--can lead to a substantial reduction in radiation exposure.

Background: The computed tomographic (CT) attenuation of coronary atherosclerotic plaque has been proposed as a marker for tissue characterization and may thus potentially contribute to the assessment of plaque instability., Objective: We analyzed the influence of reconstruction parameters on CT attenuation measured within noncalcified coronary atherosclerotic lesions., Methods: Seventy-two patients were studied by contrast-enhanced dual-source CT coronary angiography (330 millisecond rotation time, 2 x 64 x 0.6 mm collimation, 120 kV, 400 mAs, 80 mL contrast agent intravenously at 6 mL/s), and a total of 100 distinct noncalcified coronary atherosclerotic plaques were identified. Image data sets were reconstructed with a soft (B20f), medium soft (B26f), and sharp (B46f) reconstruction kernel. With the medium soft kernel, image data sets were reconstructed with a slice thickness/increment of 0.6/0.3 mm, 0.75/0.4 mm, and 1.0/0.5mm. Within each plaque, CT attenuation was measured., Results: Mean CT attenuation using the medium soft kernel was 109 +/- 58 HU (range, -16 to 168 HU). Using the soft kernel, mean density was 113 +/- 57 HU (range, -13 to 169 HU), and using a sharp kernel, mean density was 97 +/- 49 HU (range, -23 to 131 HU). Similarly, reconstructed slice thickness had a significant influence on the measured CT attenuation (mean values for medium soft kernel: 102 +/- 52 HU versus 109 +/- 58 HU versus 113 +/- 57 HU for 0.6-mm, 0.75-mm, and 1.0-mm slice thickness). The differences between 0.75-mm and 0.6-mm slice thickness (P = 0.05) and between medium sharp and sharp kernels (P = 0.02) were statistically significant., Conclusions: Image reconstruction significantly influences CT attenuation of noncalcified coronary atherosclerotic plaque. With decreasing spatial resolution (softer kernel or thicker slices), CT attenuation increases significantly. Using absolute CT attenuation values for plaque characterization may therefore be problematic., (Copyright 2010 Society of Cardiovascular Computed Tomography. Published by Elsevier Inc. All rights reserved.)

Aims: We evaluated the feasibility and image quality of a new scan mode for coronary computed tomography angiography (CTA) with an effective dose of less than 1 mSv., Methods and Results: In 50 consecutive patients (body weight

Objective: We evaluated radiation exposure and image quality of a new coronary CT angiography protocol, high-pitch spiral acquisition, using dual source CT (DSCT)., Material and Methods: Coronary CTAwas performed in 25 consecutive patients with a stable heart rate of 60 bpm or less after premedication, using 2 x 128 0.6-mm sections, 38.4-mm collimation width and 0.28-s rotation time. Tube settings were 100 kV/320 mAs and 120 kV/400 mAs for patients below and above 100-kg weight, respectively. Data acquisition was prospectively ECG-triggered at 60% of the R-R interval using a pitch of 3.2 (3.4 for the last 10 patients). Images were reconstructed with 75-ms temporal resolution, 0.6-mm slice thickness and 0.3-mm increment. Image quality was evaluated using a four-point scale (1 = excellent, 4 = unevaluable)., Results: Mean range of data acquisition was 113 +/- 22 mm, mean duration was 268 +/- 23 ms. Of 363 coronary artery segments, 327 had an image quality score of 1, and only 2 segments were rated as "unevaluable". Mean dose-length product (DLP) was 71 +/- 23 mGy cm, mean effective dose was 1.0 +/- 0.3 mSv (range 0.78-2.1 mSv). For 21 patients with a body weight below 100 kg, mean DLP was 63 +/- 5 mGy cm (0.88 +/- 0.07 mSv; range 0.78-0.97 mSv)., Conclusion: Prospectively ECGtriggered high-pitch spiral CT acquisition provides high and stable image quality at very low radiation dose.

Coronary CT angiography allows high-quality imaging of the coronary arteries when state-of-the-art CT systems are used. However, radiation exposure has been a concern. We describe a new scan mode that uses a very high-pitch spiral acquisition, "Flash Spiral," which has been developed specifically for low-dose imaging with dual-source CT. The scan mode uses a pitch of 3.2 to acquire a spiral CT data set, while covering the entire volume of the heart in one cardiac cycle. Data acquisition is prospectively triggered by the electrocardiogram and starts in late systole to be completed within one cardiac cycle. Images are reconstructed with a temporal resolution that corresponds to one-quarter of the gantry rotation time. Throughout the data set, subsequent images are reconstructed at later time instants in the cardiac cycle. In a patient with a heart rate of 49 beats/min, the Flash Spiral scan mode was used with a first-generation dual-source CT system and allowed artifact-free visualization of the coronary arteries with a radiation exposure of 1.7 mSv for a 12-cm scan range at 120 kVp tube voltage.

Objectives: Evaluation of coronary arteries at higher heart rates and in the presence of coronary stents remains problematic. The utilization of dual source computed tomography (DSCT) might improve the visualization of the coronary arteries under these conditions by imaging at a temporal resolution of 83 milliseconds, independent of heart rate., Materials and Methods: Vessel phantoms (diameter 2-4 mm) were attached to a robotic device to simulate cardiac motion and scanned with a DSCT system. The phantoms had either inserts leading to 50% stenosis or carried stents. Images were evaluated for motion artifacts and measurements of the normal, stenotic, and in-stent lumen at different heart rates (50-120 bpm) were performed. Quantile regression analysis was performed to investigate heart rate dependence of the measurement errors., Results: Visualization of the stenoses and stents was possible without motion artifacts at heart rates of up to 120 bpm. Image quality was similar for the static (0 bpm) and the dynamic (50-120 bpm) scans. Errors for diameter measurements of the vessel lumen and the stenotic lumen were low (3-mm vessel: 1-2%), but considerable for in-stent diameter measurements (3-mm stent: 27-32%). A window/level setting of 1500/300 Hounsfield units was more favorable for stent evaluation. No heart rate dependence was found., Conclusions: Depiction of coronary stents with DSCT is possible across a large range of simulated heart rates without motion artifacts and with image quality superior to that of previous generations of CT scanners.

Objective To evaluate the image quality and diagnostic accuracy of very low-dose computed tomography (CT) angiography (CTA) for the evaluation of coronary artery stenosis. Background Iterative reconstruction (IR) has shown to substantially reduce image noise and hence permit the use of very low-dose data acquisition protocols in coronary CTA. Methods Fifty symptomatic patients with an intermediate likelihood for coronary artery disease underwent coronary CTA (heart rate: 59 ± 5 bpm, prospectively ECG-triggered axial acquisition, 100 kV, 160 mAs, 2 x 128 x 0.6 mm collimation, 60 mL contrast, 6 mL/s) prior to invasive coronary angiography. CTA images were reconstructed using both standard filtered back projection (FBP) and a raw data-based IR algorithm [Sinogram Affirmed Iterative Reconstruction (SAFIRE), Siemens Healthcare]. Subjective image quality (four-point Likert scale from 0 = non-diagnostic to 3 = excellent image quality), image noise, signal-to-noise ratio (SNR), contrast-to-noise ratio (CNR), as well as the presence of coronary stenosis . 50% were independently determined by two observers. Results The mean dose-length product was 46.8 ± 3.5 mGy cm (estimated effective dose 0.66 ± 0.05 mSv). IR led to significantly improved objective image quality compared with FBP (image noise: 41 ± 12 vs. 49 ± 11 HU, P < 0.0001; CNR: 16 ± 8 vs. 12 ± 4, P < 0.0001; SNR: 13 ±7 vs. 10 ± 3, P < 0.0001). Four coronary segments were not evaluable on FBP data, whereas all segments showed diagnostic image quality with IR. To detect significant coronary stenosis, sensitivity, specificity, positive predictive value, and negative predictive value were 69% (11/16), 97% (175/180), 69% (11/16), and 97% (175/180) per vessel with FBP data sets, respectively. With IR data sets, the corresponding values were 81% (13/16), 97% (178/184), 68% (13/19), and 98% (178/181). These differences were not statistically significant (P = 0.617). Conclusions Raw data-based IR significantly improves image quality in very low-dose prospectively ECG-triggered coronary dual-source CTA when compared with standard reconstruction using FBP. [ABSTRACT FROM AUTHOR]