Search

High-performance integrated tin monoxide bottom-gate staggered p-channel thin-film transistors (TFTs) are realized and reported. The active layer has been formed by thermal vacuum evaporation and rapid thermal annealing under a continuous nitrogen flow, resulting in field-effect mobilities up to 1.6 cm2/( $\textsf {V}\cdot \textsf {s}$ ) and contact resistances of around $148~\Omega \cdot \textsf {cm}$ . The integration of these TFTs in elementary building blocks for digital circuit applications such as inverters and ring-oscillators is demonstrated, resulting in stage delays down to 300 ns. Furthermore, a unipolar p-type-only 8-bit radio frequency identification code generator is realized, achieving 12.2 kb/s and comprising 294 tin monoxide TFTs.

We present a QVGA (320x240 with 3 sub-pixel) top-emitting AMOLED display with 250ppi resolution using a self-aligned (SA) IGZO TFT backplane on polyimide-foil with full barrier. The back plane process flow is based on a 7 layer photolithography process. The aperture ratio of the top-emitting OLEDs is approx. 80%. An integrated gate driver is shown that can be driven at operation speed equivalent to a 4k2k display at 100Hz

We demonstrated self-aligned amorphous-Indium-Gallium-Zinc-Oxide (a-IGZO) thin-film transistors (TFTs) where the source–drain (S/D) regions were made conductive via chemical reduction of the a-IGZO via metallic calcium (Ca). Due to the higher chemical reactivity of Ca, the process can be operated at lower temperatures. The Ca process has the additional benefit of the reaction byproduct calcium oxide being removable through a water rinse step, thus simplifying the device integration. The Ca-reduced a-IGZO showed a sheet resistance (RSHEET) value of 0.7 kΩ/sq., with molybdenum as the S/D metal. The corresponding a-IGZO TFTs exhibited good electrical properties, such as a field-effect mobility (μFE) of 12.0 cm2/(V s), a subthreshold slope (SS−1) of 0.4 V/decade, and an on/off current ratio (ION/OFF) above 108. Cop. 2015 The Korean Information Display Society.

In this work, we report on amorphous-Indium-Gallium-Zinc-Oxide (a-IGZO) thin-film transistor (TFT) with medium frequency physical vapor deposited (mf-PVD) etch-stop-layer (ESL). TFT with mf-PVD ESL show comparable characteristics such as fieldeffect mobility (μFE), sub-threshold slope (SS−1) and current ratio (ION/OFF) to the conventional plasma enhanced chemical vapor deposition (PECVD) ESL based TFT, however significant differences were observed in gate bias-stress stabilities. The TFTs with mf-PVD ESL showed lower threshold-voltage (VTH) shifts compared to TFTs with PECVD ESL when stressed under a gate field of +/−1 MV/cm for duration of 104 seconds in dark and light conditions. We associate the better bias-stress stability of the mf-PVD ESL based TFT to better passivating properties and the low hydrogen content of the mf-PVD layer compared to PECVD layer.

A process to make self-aligned top-gate amorphous indium-gallium-zinc-oxide (a-IGZO) thin-film transistors (TFTs) on polyimide foil is presented. The source/drain (S/D) region's parasitic resistance reduced during the SiN interlayer deposition step. The sheet resistivity of S/D region after exposure to SiN interlayer deposition decreased to 1.5 kΩ/□. TFTs show field-effect mobility of 12.0 cm2/(V.s), sub-threshold slope of 0.5 V/decade, and current ratio (I ON/OFF) of >107. The threshold voltage shifts of the TFTs were 0.5 V in positive (+1.0 MV/cm) bias direction and 1.5 V in negative (-1.0 MV/cm) bias direction after extended stressing time of 104 s. We achieve a stage-delay of ~19.6 ns at V-DD = 20 V measured in a 41-stage ring oscillator. A top-emitting quarter-quarter-video-graphics-array active-matrix organic light-emitting diode display with 85 ppi (pixels per inch) resolution has been realized using only five lithographic mask steps. For operation at 6 V supply voltage (V-DD), the brightness of the display exceeds 150 cd/m2. A process to make self-aligned top-gate amorphous indium-gallium-zinc-oxide (a-IGZO) thin-film transistors (TFTs) is presented. TFTs show field-effect mobility of 12.0 cm2/(V.s), sub-threshold slope of 0.5 V/decade, and current ratio (I ON/OFF) of over 107. In applications, a 41-stage ring oscillator with a stage-delay of ~19.6 ns (at V-DD = 20 V) and a top-emitting quarter-quarter-video-graphics-array (QQVGA) active-matrix organic light-emitting diode (AMOLED) display with 85 ppi (pixels per inch) resolution using five lithographic mask steps have been realized on a polyimide foil. Copyright 2015 Society for Information Display.

In this work, we compared the thin-film transistor (TFT) characteristics of amorphous InGaZnO TFTs with six different source–drain (S/D) metals (MoCr, TiW, Ni, Mo, Al, and Ti/Au) fabricated in bottom-gate bottom-contact (BGBC) and bottom-gate top-contact (BGTC) configurations. In the BGTC configuration, nearly every metal can be injected nicely into the a-IGZO leading to nice TFT characteristics; however, in the BGBC configuration, only Ti/Au is injected nicely and shows comparable TFT characteristics. We attribute this to the metal-containing deposits in the channel and the contact oxidation during a-IGZO layer sputtering in the presence of S/D metal. In bias-stress stability, TFTs with Ti/Au S/D metal showed good results in both configurations; however, in the BGTC configuration, not all the TFTs showed as good bias results as Ti/Au S/D metal TFTs. We attribute this to backchannel interface change, which happened because of the metal-containing deposits at the backchannel during the final the SiO2 passivation.

We present a QQVGA (160times120 with 3 sub-pixel) top-emitting AMOLED display with 85ppi resolution using a self-aligned (SA) IGZO TFT backplane on polyimide-foil. The back plane process flow is based on a 5 layer photolithography process. The aperture ratio of the top-emitting OLEDs is approx. 25%. For operation at 6 V supply voltage (VDD), the brightness of the display exceeds 150cd/m2. On the same substrate a 160 stage gate-driver was measured at FHD rate. cop. 2014 Society for Information Display.

In this work, we report on high-performance bottom-gate top-contact (BGTC) amorphous-Indium-Gallium-Zinc-Oxide (a-IGZO) thin-film transistor (TFT) with SiO2 as an etch-stop-layer (ESL) deposited by medium frequency physical vapor deposition (mf-PVD). The TFTs show field-effect mobility (μFE) of 16.0cm2/(V.s), sub-threshold slope (SS -1) of 0.23V/decade and off-currents (IOFF)

In this study, we report high-quality amorphous indiunrv-galiium-zinc-oxide (a-IGZO) thinfilm transistors (TFTs) fabricated on a polyethylene naphthalate foil using a new back-channel-etch (BCE) process flow. The BCE flow allows a better scalability of TFTs for high-resolution backplanes and related circuits. The maximum processing temperature was limited to less than loS'C in order to ensure good overiay accuracy (

In this study, the authors report on high-quality amorphous indium-galliunv-zinc oxide thinfilm transistors (TFTs) based on a single-source dual-layer concept processed at temperatures down to ISCC. The dual-layer concept allows the precise control of local charge carrier densities by varying the 02/Ar gas ratio during sputtering for the bottom and top layers. Therefore, extensive annealing steps after the deposition can be avoided. In addition, the dual-layer concept is more robust against variation of the oxygen flow in the deposition chamber. The charge carrier density in the TFT channel is namely adjusted by varying the thickness of the two layers whereby the oxygen concentration during deposition is switched only between no oxygen for the bottom layer and very high concentration for the top layer. The dual-layer TFTs are more stable under bias conditions in comparison with single-layer TFTs processed at low temperatures. Finally, the applicability of this dual-layer concept in logic circuitry such as 19-stage ring oscillators and a TFT backplane on polyethylene naphthalate foil containing a quarter video graphics array active-matrix organic lightemitting diode display demonstrator is proven.

It is shown in this paper that the finite resistance of the accumulation channel in amorphous In–Ga–Zn–O thin-film transistors (a-IGZO TFTs) is the main cause of the frequency dispersion of the capacitance–voltage curves in these devices. A transmission line model, accounting for the distributed nature of channel resistance, is used to explain this. Multi-frequency analysis techniques for trap density distribution use a lumped series resistance model and attribute dispersion solely to the charging and discharging of trap states. As the resistance–capacitance (RC) time constant values of the IGZO TFTs are in the range of 10–100 µs, a distributed RC network is better suited for the measured frequency range (1 kHz–1 MHz). cop. 2014 The Korean Information Display Society.

The Internet of Things is driving extensive efforts to develop intelligent everyday objects. This requires seamless integration of relatively simple electronics, for example through `stick-on' electronics labels. We believe the future evolution of this technology will be governed by Wright's Law, which was first proposed in 1936 and states that the cost of a product decreases with cumulative production. This implies that a generic electronic device that can be tailored for application-specific requirements during downstream integration would be a cornerstone in the development of the Internet of Things. We present an 8-bit thin-film microprocessor with a write-once, read-many (WORM) instruction generator that can be programmed after manufacture via inkjet printing. The processor combines organic p-type and soluble oxide n-type thin-film transistors in a new flavor of the familiar complementary transistor technology with the potential to be manufactured on a very thin polyimide film, enabling low-cost flexible electronics. It operates at 6.5 V and reaches clock frequencies up to 2.1 kHz. An instruction set of 16 code lines, each line providing a 9 bit instruction, is defined by means of inkjet printing of conductive silver inks. ispartof: Scientific Reports vol:4 issue:1 ispartof: location:England status: published

The amorphous oxide semiconductor Indium-Gallium-Zinc-Oxide (a-IGZO) has gained a large technological relevance as a semiconductor for thin-film transistors in active-matrix displays. Yet, major questions remain unanswered regarding the atomic origin of threshold voltage control, doping level, hysteresis, negative bias stress (NBS), and negative bias illumination stress (NBIS). We undertake a systematic study of the effects of oxygen vacancies on the properties of a-IGZO by relating experimental observations to microscopic insights gained from first-principle simulations. It is found that the amorphous nature of the semiconductor allows unusually large atomic relaxations. In some cases, oxygen vacancies are found to behave as perfect shallow donors without the formation of structural defects. Once structural defects are formed, their transition states can vary upon charge and discharge cycles. We associate this phenomenon to a possible presence of hysteresis in the transfer curve of the devices. Under NBS, the creation of oxygen vacancies becomes energetically very stable, hence thermodynamically very likely. This generation process is correlated with the occurrence of the negative bias stress instabilities observed in a-IGZO transistors. While oxygen vacancies can therefore be related to NBS and hysteresis, it appears unlikely from our results that they are direct causes of NBIS, contrary to common belief.

In this work we show that the negative bias illumination stress (NBIS) of amorphous Indium Gallium Zinc Oxide (a-IGZO) transistors with an etch stop layer (ESL) deposited by physical vapor deposition (PVD) is substantially better than the NBIS of devices where the ESL layer is deposited by plasma enhanced chemical vapor deposition (PECVD). Both devices show similar transistor characteristics and bias stress in the dark but under NBIS conditions at 425 nm, PVD ESL based transistors show much less threshold voltage shift. The reduction in deep defects due to passivation by PVD layer is responsible for improved performance under NBIS. ispartof: pages:302-304 ispartof: 44th European Solid-State Device Conference - ESSDERC pages:302-304 ispartof: 44th European Solid-State Device Conference - ESSDERC location:Venice Italy date:9 Jan 2014 status: published

We investigate the relationship between charge concentration, exciton concentration, and photocurrent generation in fullerene-containing heterojunction diodes. Impedance measurements on ${\mathrm{C}}_{60}$ diodes reveal a charge buildup at the ${\mathrm{C}}_{60}$/bathocuproine (BCP) interface that can be swept out under reverse bias. In solar cell structures, a similar charge buildup is observed in dark conditions, and increases as a function of incident light intensity. Photoluminescence measurements reveal that the ${\mathrm{C}}_{60}$ exciton concentration is voltage dependent, explained via the process of exciton-polaron annihilation. This process has a negative impact on the generated photocurrent of the solar cells and thereby decreases the fill factor. A combination of electroabsorption, photoluminescence, and impedance measurements reveal a decrease in charge buildup and the associated exciton-polaron annihilation through the use of a BCP/3,4,9,10-perylenetetracarboxylic bis-benzimidazole/Ag cathode.

We present an 8b general-purpose microprocessor realized in a hybrid oxide-organic complementary thin-film technology. The n-type transistors are based on a solution-processed n-type metal-oxide semiconductor, and the p-type transistors use an organic semiconductor. As compared to previous work utilizing unipolar logic gates [1], the higher mobility n-type semiconductor and the use of complementary logic allow for a >50x speed improvement. It also adds robustness to the design, which allowed for a more complex and complete standard cell library. The microprocessor consists of two parts, a processor core chip and an instruction generator. The instructions are stored in a Write-Once-Read-Many (WORM) memory formatted by a post-fabrication inkjet printing step, called Print-Programmable Read-Only Memory (P2ROM). The entire processing was performed at temperatures compatible with plastic foil substrates, i.e., at or below 250°C [2].

We validate a model which is a combination of multiple trapping and release and percolation model for describing the conduction mechanism in amorphous indium gallium zinc oxide (a-IGZO) thin film transistors (TFT). We show that using just multiple trapping and release or percolation model is insufficient to explain TFT behavior as a function of temperature. We also show the intrinsic mobility is dependent on temperature due to scattering by ionic impurities or lattice. In solving the Poisson equation to find the surface potential and back potential as a function of gate voltage, we explicitly allow for the back surface to be floating, as is the case for a-IGZO transistors. The parameters for gap states, percolation barriers and intrinsic mobility at room temperature that we extract with this comprehensive model are in good agreement with those extracted in literature with partially-complete models.