Search

In this article, the influence of polishing orientation on surface charge accumulation and flashover characteristics of the basin spacer in a downsized dc-gas insulated transmission line (GIL) are explored by experiments. Results show that the surface charge distribution of the polished spacers is different from the untreated one. Heteropolar charges can be observed in the polished area and outward expansion area under prestressing condition. The flashover voltages of all polished spacers are decreased. The radial polishing (RP) has the greatest impact on the flashover voltage, and the flashover voltage of the radially polished spacer is decreased by 11% under positive prestressing condition. The metal dust adsorptions of the spacers are also measured, which shows that the radially polished spacer is easier to absorb metal dust and the metal dust diffuses in the radial direction. SEM and energy spectrum scanning of different spacers show that there are more exposed alumina particles on the surface of the polished area. The microdischarge induced by alumina particles is the source of heteropolar charges. When the polished area of the spacers is repaired with epoxy paint, heteropolar charges disappear on the surface of the repaired spacer. It is confirmed that charge accumulation and flashover along the spacer surface are mainly affected by the change of surface morphology on the polished area. [ABSTRACT FROM AUTHOR]

In this study, a downsized direct current (dc)-gas-insulated transmission line (GIL) model is applied to investigate the surface charging and discharging characteristics of the basin-type spacer in 0.1-MPa SF6 and air. Under a low electric field, the surface charge accumulation is dominated by the bulk conduction of the spacer. As the charging voltage increases, gas ionization occurs in the localized strong electric field, taking over the dominant position. In 0.1-MPa SF6 gas, flashovers typically develop along the convex surface of the spacer under both positive and negative voltages because the homo-charge accumulation induced by brush discharges on the concave surface aggravates the electric field distortion at the convex side. In air, the dc flashovers have the polarity effect. Under the negative voltage, the flashover development is similar to that in SF6 gas. But for positive polarity, the space charge region of positive polarity intensifies the electric field ahead of the corona region, thus promoting the air-gap breakdown at the concave side of the spacer. [ABSTRACT FROM AUTHOR]

Free metal particle can affect surface charge accumulation on epoxy insulator installed in gas-insulated transmission line (GIL) or gas-insulated switchgear (GIS), which results in reduction of surface flashover voltage thus threatening the safe operation of the power equipment. This article reports on the charge accumulation behavior on a real size epoxy insulator with bouncing metal particle under DC voltage. A coaxial electrode system was designed for the test under −30 kV, a metal particle-launching system was employed to inject the bouncing linear particle to the insulator surface. The charge distribution was measured by a Kelvin-type probe, and the influence of the particle on the charge accumulation was analyzed with the help of electric field simulation. The results showed that there were mainly two moving patterns of the bouncing particle: the charges were accumulated with speckle shape and the charged particle that hit the edge of electrode had more remarkable influence on the charge accumulation than other particles. It is suggested that the charge distribution feature is dependent upon the collision point and the trajectory of the bouncing particle. [ABSTRACT FROM AUTHOR]

Charges due to ionization at conductors at low electric field serves as the main source of charge carriers that is responsible for surface charge enhancement, especially for hetero-polar charges on the convex surface side of spacers inside DC gas-insulated transmission lines (GILs). In this paper, simulation results of charge generation processes from gas side, including natural ionization, micro-discharge and field emission, are presented. The results show that for the case where the electric field strength is -6.548 kV/mm and the gas pressure is 0.4 Mpa, when conductor roughness Ra is lower than 24.16 µm, natural radiation ionization is the main cause of the dark current. When Ra is between 24.16 µm and 188.59 µm, the dark current is dominated by micro-discharge. The Fowler-Nordheim (F-N) field emission occurs when Ra exceeds 188.59 µm. Considering the roughness of the conductor in the actual GIL, the increase in the dark current due to local roughness is mainly due to micro-discharge rather than F-N field emission. The results in this paper provide an important part for further determining of conductor surface conditions in high voltage direct current (HVDC) GILs and serve as an important reference for completion of the surface charging model of spacers under DC. [ABSTRACT FROM AUTHOR]

Surface charge accumulation on polymer insulating material has been recognized as an important factor for electric field distortion that results in reduction of surface flashover voltage. This paper reports on the charge accumulation behavior between a pair of finger-shaped electrodes on epoxy/Al2O3 nanocomposites under dc voltage superimposed by repetitive pulses. The charge distribution was measured by means of an electrostatic voltmeter, from which the average charge density could be calculated. Effects of dc voltage, nanofiller content, and pulse voltage on charge accumulation behavior were investigated. Obtained results showed that with the increase in the filler content from 0 wt% to 5 wt%, the average charge density increased initially then appeared to decrease. The superposition of repetitive pulses on dc voltage led to a remarkable growth in charge accumulation as compared with that when only dc voltage was applied. It is suggested that the charges are originated from local gaseous ionization and/or electrode injection, which is determined by the combined voltage. The charge density is dependent upon the surface trap, which is affected by nanofiller content. The superposition of repetitive pulse is considered as a possible reason to encourage local gaseous ionization that results in enhanced accumulation of surface charge. [ABSTRACT FROM AUTHOR]

Charge generation at the interfaces of gas-insulated switchgear or gas-insulated lines is mostly studied from a macroscopic point of view. Integral current measurements are a common method to determine the average inception field strengths and intensities of micro discharges. However, because of the lack of spatial resolution and measurement sensitivity, these experiments do not provide deeper insights on the microscopic processes. By applying surface potential measurement techniques, studying the charge generation of single interface protrusions and drawing conclusions relative to their spatial distribution have become possible. This paper presents a spatially resolved analysis of charge-generation processes at rough aluminum electrodes and insulating interfaces. The results reveal a highly inhomogeneous charge generation at the interfaces even for electric fields below 6 kV/mm. Analyzing the charge generation from a macroscopic perspective has been demonstrated to possibly underestimate the local charge generation by up to three orders of magnitude. Using sulfur hexafluoride (SF6) as the insulation gas at 0.45 MPa and Al2O3-filled epoxy resin insulators, the inception field strength for charge generation at the insulating interface is measured to be 3 kV/mm. For a technical insulation system that includes both a rough aluminum electrode and an insulating interface, significant discharge intensities are observed at a 5-kV/mm electric field. From these results, micro discharges are expected to be highly relevant for dimensioning of gas-insulated devices. [ABSTRACT FROM AUTHOR]

Surface charge accumulation of polymer insulating materials is harmful to the safe operation of electrical equipment, especially under DC electric field excitation. In order to ensure the safety and stable operation of HVDC power system such as Gas-insulated transmission line, it is necessary to understand the influence of the surface charge on the flashover and improve the surface charge dynamic characteristics. In this paper, Epoxy resin (EP) is deposited by SiOx thin films with different plasma treatment conditions. The flashover voltages are measured with and without surface charges. The results show that the flashover occurs at lower voltage due to the accumulated charges on the EP surface. In particular, the surface charge with the same polarity of flashover discharge can reduce the surface flashover voltage significantly. Moreover, the charge decay rate is increased up to 90% by plasma treatment of 3 min, corresponding flashover voltage is increased. In addition, the flashover voltages of samples during the surface charge dissipation are obtained. Both static impact index I and dynamic impact index S are introduced to estimate effect of surface charge on dielectric surface flashover. [ABSTRACT FROM AUTHOR]

The established theories behind low-field ion-drift currents assume that the charge generation from natural ionization is the main source of the charge-carriers, and that it defines the current flowing through the insulation gas in gas-insulated direct current (DC) devices. This charge generation is assumed to be independent of the applied electric field in the cases where the electric field is sufficiently below the onset of microdischarges at the interfaces. However, the results of a few previous studies have suggested the presence of a field-dependent current contribution from some conduction processes, which might significantly accelerate the decay of the surface charges distributed on the insulator surfaces. In this paper, an extensive study on low-field charge transport is presented, and the influences of the insulation volume, electric field, and gas pressure on low-field charge transport are discussed. In accordance with the common structure employed in gas-insulated devices, Al2O3-filled epoxy resin is used in the solid parts of the device and sulfur hexafluoride (SF6) is used for gaseous insulation. At electric fields of approximately 1800 V/m, a gas current that is up to 30 times higher, when compared to the conduction currents caused by the charge generation from natural ionization, is observed. This enhanced current reveals a further conduction process acting in a limited range of low electric fields and is characterized to be independent of the applied voltage polarity. With an increase in the gas pressure, the current amplitude is found to increase linearly and higher electric field is required to reach its maximum. At electric fields below 200 V/m, the conduction current reverses its pressure dependency and increases with decreasing gas pressure. The reported findings strongly indicate that the enhanced low-field charge transport in gasinsulated devices may be owing to electrophoretic conduction. [ABSTRACT FROM AUTHOR]

Laser-ablated template and fluoroalkyl silane modified composite coatings are used to prepare a micro- and nano-structure on silicone rubber surfaces. By testing the surface potential accumulation and dissipation process, we assess the suppression of surface charge on superhydrophobic silicone rubber. The surface physicochemical properties and resistivity are examined. The electron and hole trap distribution are analysed using isothermal current decay theory. Peak density of traps associated with the superhydrophobic surfaces are found to be promoted to lower energy levels relative to unmodified silicone. Surface micro-structure increases trap density and reduce trap depth; nano coatings are shown to further reduce surface trap depth. The improvements shown to suppress surface charge accumulation is beneficial to a range of electrical industries and helps mitigate surface flashover on insulation. [ABSTRACT FROM AUTHOR]

Polyimide (PI) films have excellent electrical, mechanical and thermal properties in aspect of resisting corona, aging and radiation. However, the pulse voltage combined with dc voltage often causes concentration of local electrical field, which makes the surface charge behaviors more complex and threatens the system. As a means of surface treatment, direct fluorination has been proved as an effective way to improve the polymer properties, without compositing the bulk characteristics. Therefore, this paper intends to reveal the effects of fluorination on surface charge coupling behaviors of the PI films under dc and pulse voltage combination. The PI samples fluorinated for 0, 15, 45 and 60 min were obtained. Surface corona discharging was stressed under the combination of dc and pulse voltage. The surface charge accumulation, decay and distribution were measured coupled with an analysis of trap distribution. The results show the surface charge dynamic behaviors are strongly correlated with the fluorination time, pulse voltage amplitude and polarities of the dc and pulse voltage combination. The trap distribution results imply that the effect of fluorination and charging condition attribute to the change of trap depth and amount. Besides, surface charge behaviors are greatly improved by appropriate fluorination. [ABSTRACT FROM AUTHOR]

Epoxy is widely used in electronic and electrical devices because of its excellent insulation properties. The addition of nanoparticles to epoxy could change the material structure and then charge behaviors are altered as a consequence. The accumulation of surface charge may cause electric field distortion, which would lead to surface flashover. In this paper, the samples were made by dispersing nano-scale boron nitride (BN) particles in Epoxy with the weight ratios of 5, 10, 20, 30, 40 wt%. The samples were charged by a dc corona triode system using needle-plate electrodes. The distribution of charges was measured with an electrostatic voltmeter and the effect of nanoparticles on charge accumulation and decay behavior was studied. A flashover test was carried out under a dc stress between two finger-type electrodes. The effect of nanoparticles on flashover characteristics and the relation between surface charging and surface flashover were also investigated. The results showed that the traps between nanoparticles and the polymer, which were introduced by the added nanoparticles, could cause surface charge accumulation. In addition, the flashover occurred at a lower voltage because of the accumulated charge on the sample surface. [ABSTRACT FROM AUTHOR]

Polyimide film, as a special type of engineering plastic film, is a basic insulating material and is widely applied in the electrical and electronic industry. Addition of nanoparticles into polyimide can improve the insulating properties compared with undoped material. However, due to the change of the material structure, the trap characteristics and charge behavior are altered as a consequence. The existence of surface charge has a great effect on the breakdown characteristic and is the main reason leading to dielectric breakdown. Fluorination as change the chemical component in surface layer of polymers should give rise to the corresponding change in electrical properties of the surface layer thus influence the charge injection from electrodes when they are used as an insulator. This paper presents a study aimed at clarifying the effect of fluorination and nanoparticles on the surface charge accumulation and decay behaviors of fluorinated polyimide nanocomposite film. Samples were prepared by dispersing nano-scale Al2O3 into polyimides with weight percentages of 0, 1, 3, 5 and 7 respectively. Then the samples were surface fluorinated in a laboratory vessel at about 328 K (55 °) using a F2/N2> mixture with 20% F2 by volume and 0.05 MPa (500 mbar) for 30 minutes. Corona charging tests were performed at room temperature with a relative humidity of ˜ 40%. The charge distribution was measured by means of an electrostatic voltmeter. The results show the dependence of the charge density as well as the charge decay rate upon the fluorination and nanoparticle concentration, varying as a function of the charge polarity and charging time. It is suggested that the fluorination can significantly improve the decay rate of the surface charge in polyimide films. [ABSTRACT FROM AUTHOR]

It seems generally accepted that HVDC technology is to become increasingly relevant in power systems. With this expected future advance of HVDC, the use of gas insulated switchgear or lines for dc application are getting increasingly interesting. As in the case of dc the electric fields are determined resistively in contrast to the capacitive fields in the case of ac, gas insulated technology has to be revisited. In many previous works surface charging of model spacers was investigated. However, the ion flow problem to properly account for the electric conduction in the gas has not yet been solved. Further, no combination with inhomogeneous electric conductivity determined for example by temperature profiles from ohmic heating in nominal condition has been performed so far. In this paper, the gas conductivity arising from ions produced by natural radiation is computed by solving the ion flow field problem, and its role is compared to spacer bulk conductivities. Further, the impact of temperature profiles on spacer charging is investigated. The results indicate that for actual disc spacers, the spacer bulk conductivity is more important than that from the gas ionized by natural radiation. Especially in the case of polarity reversal, thermally enhanced spacer charging can result in considerable increase of tangential field strengths. [ABSTRACT FROM PUBLISHER]

Effect of surface charges on dc flashover characteristics of a composite polymeric insulator is studied by means of experiments and theoretical calculations. The considered insulator consisted of a glass fiber reinforced epoxy core covered with a layer of silicone rubber and terminated by metallic electrodes with rounded smooth edges. In the experiments, the insulator surface was charged by external corona while keeping the electrodes grounded and different charging levels were realized by varying its intensity. A series of disruptive discharge tests were carried out on the charged insulator under negative dc voltages. It was revealed that negative deposited surface charges led to an enhancement of the flashover performance whereas positive ones reduced the flashover voltage level. A theoretical model has been developed and utilized for analyzing the experimental results. In the model, surface charge density profiles deduced from measured surface potential distributions were used as boundary conditions for calculations of electric fields. The measured and calculated flashover voltages were found to be in agreement indicating that the observed variations in the flashover characteristics could be attributed to the modifications of the electric field produced by the surface charges. [ABSTRACT FROM PUBLISHER]