Search

Buried power rail (BPR) is a key scaling booster for CMOS extension beyond the 5-nm node. This work demonstrates, for the first time, the integration of tungsten (W) BPR lines with Si finFETs. BPR technology requires insertion of metal in the front-end-of-line (FEOL) stack. This poses risks of stack deformation and device degradation due to metal-induced stress and contamination. To assess the stack deformation, we demonstrate W-BPR lines which can withstand source/drain activation anneal at 1000 °C, 1.5 s, without adversely impacting the stack morphology. To address the contamination risk, we demonstrate a BPR process module with controlled W recess and void-free dielectric plug formation which keeps the W-line fully encapsulated during downstream FEOL processing. Suitable choice of BPR metal such as W with high melting point which does not diffuse into dielectrics also minimizes the risk of contamination. To assess the device degradation, simulations are carried out showing negligible stress transfer from BPR to the channel. This is experimentally validated when no systematic difference in the dc characteristics of CMOS without BPR versus those in close proximity to floating W-BPR lines is observed. Additionally, the resistance of the recessed W-BPR line is measured $\sim 120~\Omega /\mu \text{m}$ for critical dimension (CD) ~32 nm and height ~122 nm. The recessed W-BPR interface with Ru 3-nm TiN liner via contact can withstand more than 1000 h of electromigration (EM) stress at 6.6 MA/cm2 and 330 °C, making Ru a candidate for via metallization to achieve low resistance contact strategy to BPR.

We propose, for the first time, an indium gallium zinc oxide (IGZO)-based 2T1C compute cell (IGZO-cell) for analog in-memory computing. To assess the impact of an IGZO-cell-based array including the periphery on power and accuracy, a PyTorch framework was developed to analytically modeled analog components. The results are reported for a ResNet20 network on the Canadian Institute For Advanced Research-10 (CIFAR-10) benchmark. The state-of-the-art energy efficiency of 15 peta operations per second (POPS)/W including the periphery is achieved by using our proposed IGZO-cell with CMOS compatibility. Finally, it is shown that, with a properly trained neural network model, there is no degradation of test accuracy with 10% device to device variability for the IGZO devices.

In this work, IGZO device integration is reported leveraging our 300mm-fab facilities. Our objective is mainly to gain insights into the process and material elements which drive the control of the performance parameters of IGZO nFETs. To control the final doping of the IGZO channel, it is well reported in literature that a final oxygen anneal can be applied to passivate the oxygen vacancies which are formed during the device fabrication. This technique is also used in our 300mm flow. As it might be expected, in front gate IGZO nFETs, the passivation efficiency is limited by the presence of the top metal gate stack. Therefore, it seems important to limit the formation of the oxygen vacancies during the deposition of the gate dielectrics. Three oxides were studied: SiO2, Al2O3 and HfO2 on top of the IGZO channel. After oxygen annealing, only PECVD-SiO2 shows a large recovery while for Al2O3 and HfO2, it remains low. This result challenges the implementation of conventional water-based high-K materials in gate first IGZO integration. Contrary to the use of undoped IGZO in the channel for IOFF control, contacts can rely on maximizing the oxygen vacancies to increase the dopant concentration in the S/D regions. When not done locally, it could be an extra source of variability. This doping is made through oxygen scavenging from IGZO by a thin metal contact barrier. Low specific contact resistivity down to 1x107 Ohm.cm2 is demonstrated when Ti is thinner than 5nm. With thicker barrier, the formation of TiO2 and specific alloys is taking place at the IGZO/Contact barrier interface. This is both confirmed by ab initio simulations and by advanced physical characterization techniques. Regarding the channel, X-ray diffraction techniques are extensively here since this is a nondestructive in-fab technique that provides detailed information about the crystallographic structure of the IGZO material. We show a typical spectrum where clear peaks/humps are seen and attributed to: 1. amorphous IGZO, 2. CAAC-IGZO and 3. a previously not reported, to the best of our knowledge, phase called here s-IGZO. The s-phase is only formed under certain conditions of power, temperature and oxygen flow during material deposition. Thick IGZO (>12nm) back-gated nFETs with active layers submitted to final O2 anneal are used to study the different phases of IGZO and their electrical impact on device parameters. In this configuration, the carrier transport preferentially occurs in the bottom half of the IGZO channel while the top half (SiO2/IGZO interface) mostly drives the electrostatic control of BG transistors. The amorphous IGZO has much reduced spread in VTH-ON and higher ID,LIN (~mobility) than that of CAAC-IGZO. Reliability tests have also been carried out to compare the two phases and the results show the existence of two competing PBTI degradation mechanisms for CAAC-IGZO. It is important to report the degradation over time and different VG stress because a cut line at a specific value could have shown no BTI degradation of CAAC-IGZO and then attributing an unfair benefit of this phase over the a-IGZO phase. Combining these findings to some other results where the sheet resistance of IGZO under hydrogen exposure depends on the phases, we can reasonably conclude that CAAC owns different doping levels in comparison to a-IGZO. Based on the previous learning about n-type dopant location in IGZO, we show that the performance of transistors keeps increasing when the channel length is reduced and scales with the channel width. A measure of the VTH-ON variation has been performed at the 300mm wafer scale from long to ~120nm LCH and down to 200nm WCH dimensions. The figure in attachement shows the Id-Vg curves of >100 Back Gated IGZO-nFETs with no failed devices detected. The standard variation of the VTH-ON across LCH and WCH is often less than 40mV with a minimum of 20mV. In conclusion, we have demonstrated in this study scaled IGZO nFETs with excellent VTH_ON control using an industry compatible 300mm process flow. This has been achieved thanks to a careful mapping of n-type doping in the three dimensions of the IGZO channel. While semi-crystalline IGZO seems to be more robust against hydrogen than that of amorphous-IGZO, a new IGZO phase is found to help boost ION at short channel. The demonstration of back-gate IGZO nFETs with low variability and relatively high drive will benefit to the top-gate architecture development. This will provide new opportunities for the IGZO-based devices like an “on-the-fly” VTH setting for the performance control of advanced applications. Figure 1

3-D sequential integration requires top MOSFETs processed at a low thermal budget, which can impair the device reliability. In this paper, top junctionless (JL) devices are fabricated with a maximum processing temperature of 525 °C. The devices feature high k/metal replacement gate and low-temperature Si:P and SiGe:B 60% raised source and drain for nMOS and pMOS fabrication, respectively. Device matching, analog, and RF performance of the top tier devices are in-line with the state-of-the-art Si technology processed at high temperature (>1000 °C). JL devices operate at reduced electric field and can meet in specification reliability (10-year reliable operation at ${V}_{\textsf {G}}= {V}_{\textsf {th}}+ 0.6$ V, 125 °C), even without the use of “reliability” anneal. The top Si layer is transferred on CMOS planar bulk wafers with W metal-1 interconnects, using a SiCN to SiCN direct wafer bonding. Comparison with silicon-on-insulator devices fabricated with the same low-temperature flow shows no impact on device electrical performance from the Si layer transfer.

We report for the first time a fully 300-mm stacking-compatible capacitor-less DRAM cell with >400s retention time by integrating two IGZO-TFTs in a 2T0C configuration. We optimize the single IGZO-TFT performances by engineering the materials surrounding the IGZO layer and the transistor layout parameters. We thus introduce a novel IGZO-TFT device and demonstrate a scaled transistor (W = 70 nm, L = 45 nm) with optimal V th reproducibility on 300-mm wafers. By integrating the IGZO-TFTs in a 2T0C configuration, we systematically assess reproducible long retention time for different transistor dimensions, thanks to the extremely low extracted IGZO-TFT off-current (~3x10-19A/µm).

Buried power rail (BPR) is a key scaling booster for CMOS extension beyond the 5 nm node. This paper demonstrates, for the first time, the integration of tungsten (W) BPR lines with Si finFETs. The characteristics of CMOS in close proximity to floating BPR are found to be similar to the characteristics of CMOS without BPR. Moreover, W-BPR interface with Ru via contact can withstand more than 320 h of electromigration (EM) stress at 4 MA/cm 2 and 330°C, making Ru a candidate for via metallization to achieve low resistance contact strategy to BPR.

Since the challenges of maintaining the Moore's law - through traditional dimensional scaling or exploiting new materials properties - are becoming increasingly difficult, 3D integration technologies are gaining more and more attention and importance. At system level 3D-SOC solutions are of great interest, in particular those obtained through Wafer-to-Wafer (W2W) bonding due to superior overlay performance. In this paper we present the development of etch process modules for fine pitch via last interconnects realized on wafers with dielectric bonding and their integration in a packaging test chip, followed by electrical characterization.

Over the past few years, extreme wafer thinning has acquired more interest due to its importance in 3D stacked system architecture. This technique facilitates multi-wafer stacking for via last advanced packaging. From a cost and wafer integrity point of view, it has been demonstrated that the best process flow combines grinding with fast Si removal using Reactive Ion Etching (RIE). For this integration scheme, final thickness, and global flatness are key for subsequent steps. The wafer thinning performances are driven by several steps and can lead to lot, wafer to wafer and within wafer variations especially at the extreme edge. The first part of this study is to demonstrate stable wafer thinning with good control of the remaining Si (up to 5 μm) during the RIE process. This uses an innovative in-situ endpoint system (Near Infra-Red reflectometry) where the Si thickness is monitored whilst etching. The second part will focus on adjustment of the etch profile to compensate for incoming non-uniformity. This has been investigated from three different perspectives: Hardware modification where the ceramic ring surrounding the wafer is modified, process modification to change the etch front through changing the gas flow and plasma shape and changing the edge trim to introduce additional loading at the edge.

3D sequential integration is shown to be compatible with a back gate implementation suitable for dynamic V th tuning of the FDSOI top tier devices. The back gate is inserted seamlessly into the 3D sequential process flow during the top Si layer transfer, providing a close proximity to the top tier device, as well as a uniform and high quality thermal back oxide. A threshold voltage tuning of ~103mV/V and ~139mV/V is obtained in p-and nMOS top tier junction-less devices, respectively, over a back gate bias range of +/-2V. BTI reliability measurements show no detrimental impact of the back gate bias. Back-gating can therefore be used to enhance the $I_{ON}$ performance with no reliability penalty. The buried metal line is also shown to lower crosstalk by metal shielding insertion between top and bottom tier metal lines, with a reduction larger than 10dB up to 45GHz.

In this paper, patterning challenges that led to the fabrication of a first Spin Torque Majority Gate (STMG) device are explored. We have highlighted key process module developments from the Magnetic Tunnel Junctions (MTJs) pillar patterning to dual damascene scheme wiring module. Spin devices such as STMG have already been proposed as a replacement for conventional CMOS transistors. The main challenge to their experimental demonstration remains the successful fabrication of connected MTJs through a ferromagnetic layer, allowing spin transport across the gate. We propose a new etching approach utilizing Ion Beam Etching (IBE), to be able to pattern the MTJs with high precision and with less damage to the magnetic layers. Furthermore, we have introduced Electron-beam lithography to further scale down the device geometries. This development paves the way towards a fully integrated STMG device for Spin Logic applications.

Extreme ultraviolet (EUV) materials are deemed as critical to enable and extend the EUV lithography technology. Currently both chemically amplified resist (CAR) and metal-oxide resist (MOR) platforms are candidates to print tight features on wafer, however patterning requirements, process tonality (positive or negative), illumination settings and reticle tonality (dark or bright) play a fundamental role on the material performance and in consequence on the material choice. In this work we focus on the patterning of staggered pillars using a single EUV exposure, and this by looking at the lithographic and etching performance of CAR and MOR platforms, using metrics as process window, local critical dimension uniformity (LCDU), pillar edge roughness (PER), pillar placement error (PPE) and (stochastic) nano-failures. As a bright field reticle shows a lower aerial image contrast to print pillars compared to the aerial image of contact holes using a dark field reticle, we also investigate alternative patterning solutions such as the tone reversal process (TRP) to pattern pillars from contact holes.

3 Dstacking using a sequential integration approach is demonstrated for finfet devices on 300mm wafers at a 45nm fin pitch and 110nm poly pitch technology. This demonstrates the compatibility of the 3D sequential approach for aggressive device density stacking at advanced nodes thanks to the tight alignment precision of the first processed top layer to the last processed bottom layer through the top silicon channel and bonding stack during 193nm immersion lithography. The top devices are junction-less devices fabricated at low temperature $(\mathrm{T}\leq 525^{\circ}\mathrm{C})$ in a top Si layer transferred by wafer-to-wafer bonding with a bonding dielectric stack down to 170nm. The top devices offer similar performance as the high temperature bulk finfet technology for LSTP applications. The use of TiN/TiA1/TiN/HfO 2 gate stack provides the proper threshold voltage adjustment while the insertion of the LaSiO x dipole improves device performance and brings the BTI reliability within specification at low temperature.

3D sequential integration requires top MOSFETs processed at low thermal budget, which can impair the device reliability. In this work, top junction-less device are fabricated with a maximum processing temperature of 525°C. The devices feature high k /metal replacement gate and low temperature Si:P and SiGe:B 60% raised SD for NMOS and PMOS respectively. Device matching, analog and RF performance of the top tier devices are in-line with state-of-the-art Si technology processed at high temperature (>1000°C). The top Si layer is transferred on CMOS planar bulk wafers with W metal-1 interconnects, using a SiCN to SiCN direct wafer bonding.

In this paper, we review the current progress on 3D sequential device stacking, highlighting the main integration challenges and the possible technological solutions. Junction-less devices are shown to be attractive top tier devices for low temperature processing, low complexity of fabrication and meeting reliability specification despite without the use of “reliability” anneal. Next, we explore the potential benefits of 3D sequential stacking at transistor level, CMOS level and for hybrid circuits.

In this paper, we review the current progress on 3D sequential device stacking, highlighting the main integration challenges and the possible technological solutions. Next, we explore the potential benefits of 3D sequential stacking at transistor level, CMOS level and for hybrid circuits.

Ruthenium has been recently considered as a promising candidate to replace copper as the BEOL interconnect material for sub-5nm technology nodes. In this work, single level Ru interconnects were fabricated in imec's 300-mm pilot line using EUV lithography and the subtractive etch of Ru films. Lines with critical dimension smaller than 10.5 nm were formed and electrically tested to assess the line resistance of patterned Ru. Using the TCR method, structures with resistivity of 15 μΩ.cm and cross-sectional area of 200 nm2 were obtained and benchmarked against analogous Ru and Cu damascene processes. Ru lines with aspect ratio up to 3.8 were fabricated and measured having line resistance below 500 Ω/μ $m$ at 12 nm CD. Ru is expected to outperform damascene Cu at this scale, supporting the potential insertion of Ru metal patterning for advanced technology nodes.

Extreme thinned wafer transfer technologies have been demonstrated by combining a selected set of temporary and permanent bonding materials. The extreme thinning was performed on the backside of a top wafer bonded on carrier wafer with the temporary glue material, subsequently followed by grinding, polishing and plasma dry etching to a final thickness of 5 µm. The properties of the temporary adhesive have been selected to be compatible with a permanent thermocompression bond of the extreme thin wafer to a final target substrate. Thus, the high thermal deformation resistance of the temporary adhesive is key. As we are dealing with extremely thin substrate, the required process uniformity and total thickness variation of each material are crucial. Hence after the spin-coating, the permanent bond polymer was planarized by a surface planer process. The performance benefit brought by this process and the final transfer steps will also be discussed.

Magnetic tunnel junctions (MTJs) interconnected via a continuous ferromagnetic free layer were fabricated for Spin Torque Majority Gate (STMG) logic. The MTJs are biased independently and show magnetoelectric response under spin transfer torque. The electrical control of these devices paves the way to future spin logic devices based on domain wall (DW) motion. In particular, it is a significant step toward the realization of a majority gate, even though further downscaling may be required. To our knowledge, this is the first fabrication of a cross-shaped free layer shared by several perpendicular MTJs. The fabrication process can be generalized to any geometry and any number of MTJs. Thus, this framework can be applied to other spin logic concepts based on magnetic interconnect. Moreover, it allows exploration of spin dynamics for logic applications, Comment: submitted to Japanese Journal of Applied Physics

With the rapid progress of spintronic devices, spin-logic concepts hold promises of energy-delay conscious computation for efficient logic gate operations. We report on the electrical characterization of domain walls in interconnected magnetic tunnel junctions. By means of spin-transfer torque effect, domains walls are produced at the common free layer and its propagation towards the output pillar sensed by tunneling magneto-resistance. Domain pinning conditions are studied quasi-statically showing a strong dependence on pillar size, ferromagnetic free layer width and inter-pillar distance. Addressing pinning conditions are detrimental for cascading and fan-out of domain walls across nodes, enabling the realization of domain-wall-based logic technology.

In this work, Ru wires patterning by direct etch are evaluated for a potential 5 nm technology node. The characteristics of Ru etching by varying the bias voltage, total flow rate and Cl2/(O2+Cl2) gas flow ratio are studied in an inductively couple plasma etching chamber. Ru sidewalls profile with a tapering angle of 90° and Ru to SiO2 hard mask etch selectivity of 6 are achieved. The authors show the feasibility of patterning lines with an aspect ratio up to 3.5 and lines with a critical dimension down to 10.5 nm (with a 3σ line width roughness of 4.2 nm), which paves the way to further scaling of this approach. Finally, the authors present a study on Ru line roughness after patterning on 300 mm wafers. Here, they compare line roughness results of wafers where Ru is deposited with different deposition techniques, such as atomic layer deposition and plasma vapor deposition, and it is annealed after deposition at various temperatures.In this work, Ru wires patterning by direct etch are evaluated for a potential 5 nm technology node. The characteristics of Ru etching by varying the bias voltage, total flow rate and Cl2/(O2+Cl2) gas flow ratio are studied in an inductively couple plasma etching chamber. Ru sidewalls profile with a tapering angle of 90° and Ru to SiO2 hard mask etch selectivity of 6 are achieved. The authors show the feasibility of patterning lines with an aspect ratio up to 3.5 and lines with a critical dimension down to 10.5 nm (with a 3σ line width roughness of 4.2 nm), which paves the way to further scaling of this approach. Finally, the authors present a study on Ru line roughness after patterning on 300 mm wafers. Here, they compare line roughness results of wafers where Ru is deposited with different deposition techniques, such as atomic layer deposition and plasma vapor deposition, and it is annealed after deposition at various temperatures.