Search

The extra-LC auxiliary-resonant-snubber-based converter (ELCARSC), as a soft-switching converter, has the advantages of low switching loss, low electromagnetic interference noise, and low-output distortion caused by the dead-time effect. However, the dead-time effect is still the main problem in a high-precision application. Besides, the traditional control and compensation methods rely on the accuracy of the circuit parameters, especially the junction capacitance, thus resulting in compensation error. Therefore, this paper proposed a novel high-precision control method through modulating the initial resonant current to eliminate the dead-time effect of ELCARSC. The method does not need complicated online calculation and reduces the dependence on the accuracy of the circuit parameters, especially the influence of the junction capacitances of the switches. In this paper, the dead-time effect of the ELCARSC is analyzed. The output voltage error with the conventional variable-timing control method is analyzed. Subsequently, the proposed modulated initial resonant current control is introduced. Finally, a prototype was developed that verified the effectiveness of the control method. The quality of the output current and voltage is improved by utilizing the proposed control method. However, the peak current of the auxiliary switch is increased. [ABSTRACT FROM AUTHOR]

Motors and inverters are increasingly being used in vehicles. As more vehicle components are being adopted, requirement for safety and installation space are increasing. Growing attention is being paid to the use of six-phase permanent magnet synchronous motors (PMSMs) and their parallel control by two inverters, because of their reduced size and enhanced safety. This paper proposes a pulsewidth modulation (PWM) control algorithm for a six-phase PMSM. In low-voltage vehicle components such as electric power steering, the current is usually acquired with resistors placed under the low-side switching devices. In the proposed control algorithm, the neutral voltage of the two inverters is shifted to either a lower or higher voltage within a certain range to allow for the signal conditioning time delay after the switching device turns on or off, and the time taken for the phase current to rise or settle. The paper proposes a novel PWM control algorithm that ensures that the on-time of the low-side switching devices satisfies the restriction on current sensing with resistors and reduces the current in the capacitor at the same time. The work contributes to reducing the current in a practical configuration involving low-voltage vehicle components. [ABSTRACT FROM AUTHOR]

Induction motor drives operated with a low ratio of the switching frequency to the fundamental frequency (i.e., pulse number) are prone to have high magnitudes of low-order torque harmonics. This paper proposes a method to analytically evaluate the harmonic torque spectrum based on the pulsewidth-modulated voltage waveforms for low pulse number operation. The predicted torque harmonic spectra for different pulsewidth-modulated waveforms are validated through simulations and experiments. This paper also reports optimal switching angles to minimize the total rms value of torque harmonics of order 6, 12, 18 $,\dots,$ $6(N-1)$ , considering the number of switching angles per quarter ($N$) to be 4 and 5. Compared to sine triangle pulsewidth modulation and selective harmonic elimination pulsewidth modulation with the same pulse number, the proposed optimal switching angles significantly reduce the total rms value of all harmonic torques of order lower than $6N$. Extensive simulation and experimental results on a 3.7-kW induction motor drive are presented to demonstrate the superior performance of the proposed optimal pulsewidth modulation. [ABSTRACT FROM AUTHOR]

This paper proposes a new dc–ac converter with a reduced number of semiconductor switches and gate drive and control circuit components. A salient feature of this inverter is its pure sinusoidal line-to-line voltages with no need for output filter. Also, the proposed inverter improves the voltage utilization factor of the input dc supply compared to the four-switch three-phase inverter (first best topology in the literature from the number of switches point of view) and standard six-switch inverter with sine pulsewidth modulation. The proposed inverter is capable of operating with a wide range of output voltages from zero to the full value of the dc input voltage by appropriately altering the instantaneous duty cycle. A three-phase universal inverter with only three power switch has been proposed in this paper for the first time ever, to our knowledge. For the purpose of providing a good compromise between fast transient response and stability, a model predictive controller is proposed. All the design expressions have been derived. A comparison with other dc–ac converters is given to show the merits of the proposed converter. Finally, satisfactory circuit operation is confirmed by experimental results from a laboratory prototype. [ABSTRACT FROM AUTHOR]

In this paper, two structures are proposed for the switched-inductor quasi-Z-source inverter. In the proposed structures to extend the voltage gain of inverter, two new switched-inductor structures are used. In the proposed structures, voltage across the capacitors in the Z-source network and in the switched-inductor is symmetric and small. The other advantage of proposed inverters is known as achieving higher voltage gain per smaller duty cycle ratio (of shoot-through). Compared with a conventional continuous input current switched-inductor quasi-Z-source inverter at the same gain voltage, there is less of a ripple of input current in the proposed inverters. In this paper, at first the both the conventional and the proposed switched-inductor Z-source inventers are thoroughly investigated to find out their governing relations. Then, the proposed Z-source inverters are compared with the conventional ones by simulating them to assess their performance efficiency. Next, applying the simple boost pulse width modulation the simulation is carried out with PSCAD/EMTDC software. After that, to evaluate the obtained results, the prototypes of the proposed inverters with 48 Vdc input voltage are used. [ABSTRACT FROM PUBLISHER]

This paper analyzes the combination in a cascaded H-bridge multilevel inverter (CHBI) based on transformers with the different turn ratios for increasing the voltage level and proposes the switching method for achieving the output voltage distribution among H-bridge cells (HBCs). The transformers used in this paper are connected to the output of the respective HBCs, and the secondary sides of all the transformers are connected in series for generating the final output voltage. Only one of the transformers, in particular, has a different turn ratio for increasing the output voltage level. In this paper, the possible turn ratio of the special transformer with a different turn ratio is discussed in detail, and a switching method based on the level-shifted switching method for the topology used in this paper is proposed. To verify the effectiveness of the proposed method, a three-phase 21-level CHBI is experimentally tested. [ABSTRACT FROM PUBLISHER]

In this paper, new half-bridge and full-bridge topologies for a switched-boost inverter are proposed. These topologies have a high boost factor in comparison with conventional types. In addition, the proposed topologies have continuous input current and can generate zero-voltage level in output. In this paper, the operation of the proposed inverters in different operating modes is analyzed. Then, the values of inductors and capacitors are designed. Moreover, the used switching pattern and its logical diagram are introduced. A comprehensive comparison between the proposed and conventional topologies in terms of the boost factor, the number of elements, and the efficiency shows the good features of the proposed inverters. Finally, to verify correct operation of the proposed topologies and derived equations, simulation and experimental results are presented. [ABSTRACT FROM AUTHOR]

Digital current controllers have the key impact on the performance of grid-side converters and ac drives. The voltage disturbances are commonly suppressed by enhancing the controller with an inner active resistance feedback. In cases where the switching noise and parasitic oscillations introduce sampling errors, conventional sampling is replaced by the oversampling-based error-free feedback acquisition which derives the average of the measured currents over the past switching period. The time delay introduced into the feedback path creates difficulties in designing the current controller with the active resistance. In this paper, we introduce a novel structure of the current controller, which includes the error-free sampling and the active resistance feedback. Devised structure improves the disturbance rejection by extending the range of permissible values of the active resistance. Controller structure is based on the internal model principles, and it maintains the input step response unaffected. This paper comprises analytical design, the gain setting procedure, computer simulation, and experimental results obtained from an experimental setup with a three-phase inverter, digital controller, and a permanent-magnet synchronous motor. [ABSTRACT FROM PUBLISHER]

A novel hybrid pulse width modulation (PWM) technique is proposed in this paper for two parallel interleaved, two-level, three-phase voltage source inverters (VSIs). The two parallel interleaved VSIs are analyzed as a three-level (3L) inverter. A 3L inverter provides minimum line current ripple when nearest three voltage vectors are applied. In this paper, a novel carrier-based PWM technique is developed that ensures the application of nearest voltage vectors, keeping average circulating current to zero over a switching period. For carrier-based implementation of the proposed PWM, generalized common-mode (CM) offsets are derived in terms of maximum and minimum values of reference signals. Each 3L space-vector sector is divided into seven subsectors. For each subsector, a CM offset is calculated, addition of which to reference signals ensures the minimum line current ripple and zero average circulating current. Simulation and experimental results are provided to validate the proposed technique. [ABSTRACT FROM PUBLISHER]

For power converters with inductive loads, a freewheeling path is needed for the current due to reactive power. The MOSFET synchronous rectification (SR) is widely used to reduce the conduction loss during the freewheeling period. Due to the wide band gap of silicon carbide (SiC), the intrinsic body diode of SiC MOSFET exhibits a high voltage drop. Hence, an antiparallel SiC Schottky diode is normally implemented to eliminate its conduction. However, the external SiC Schottky diode is not fully utilized as it only works during the dead time. In this paper, the hard-switching SR is investigated in an SiC three-phase inverter and compared with a conventional inverter using freewheeling diode (FWD). An improved power loss model for the two inverters has been developed. It is found that the inverter using SR has higher efficiency due to the smaller switching loss. A 7-kW prototype of SiC three-phase inverter is built, which achieves a peak efficiency of 98.8% ($\pm$ 0.15%) and 98.5% ($\pm$ 0.15%) at 40 kHz using SR and FWD, respectively. This paper confirms that the SiC MOSFET is an ideal candidate for the SR. [ABSTRACT FROM PUBLISHER]

This paper proposes and validates model predictive control as an alternative control strategy for H-bridgeneutral-point-clamped (H-NPC) converters for single-phase grid-tied string photovoltaic (PV) systems. The presented control scheme achieves good quality current waveforms with unity power factor, dc-link voltage control, and neutral-point voltage minimization. Furthermore, the predictive controller has been further enhanced by including an average device switching frequency restriction and a $dv/dt$ mitigation. The main contribution of this paper is the avoidance of the potential leakage current due to parasitic capacitance of the PV modules by using a predictive model based control technique instead of modulated schemes and eliminating high-frequency common-mode voltage components. Experimental results during steady state and dynamic operation are presented to illustrate the behavior of the H-NPC converter commanded by the proposed control scheme. [ABSTRACT FROM AUTHOR]

This paper proposes an effective sliding mode controller (SMC) for a grid-connected 7-level packed U-cell (PUC7) inverter. The aim is to design a simple controller that deals effectively with the complex control problem of the PUC7 inverter (multiobjective control problem). The selection of the control actions is achieved according to the system state error at every sampling time, regardless of the previous values, which makes the control technique model-independent. The control algorithm evaluates online two cost functions (one for each state error), which are derived on the basis of sliding mode theory, and it selects the optimal control input in order to satisfy the reaching conditions of the two cost functions. Compared with the existing solutions, the proposed SMC technique ensures lower average switching frequency by tuning the hysteresis bandwidth of the capacitor-voltage error. The fast implementation, needless of gains tuning, and simple design procedure are the main features of the proposed algorithm. Simulation and experimental results are presented to prove the effectiveness of the proposed technique in controlling the PUC7 inverter with high dynamic performance and robustness against disturbances and parameters mismatch. [ABSTRACT FROM AUTHOR]

This paper presents a new four-quadrant (4Q) boost-type converter with the use of active virtual ground (AVG) technology. The presented topology can step up the ac grid voltage to a regulated dc voltage under a stable bidirectional current flow and support the power transmission in either real power or reactive power delivery. With the use of the proposed modulation method, only two high-frequency switches are required through the 4Q operation. Under a full-bridge converter structure, an efficient system can be guaranteed. Also, benefiting from the AVG technology, an LCL filter is formed at the system input over the 4Q operation. Both magnitude of leakage current and grid current ripple are also minimized to a small value. Thus, a high-efficiency and low-noise 4Q converter is guaranteed. The presented topology is successfully implemented on a 750 VA prototype and the performance is experimentally verified on it, which shows good agreement with the theoretical knowledge. [ABSTRACT FROM AUTHOR]

In this paper, a new Lyapunov-based model predictive controller is proposed for a 7-level packed U-cell (PUC7) grid-connected inverter. A cost function of the proposed model predictive controller is designed from the system stability point of view, inspired by the Lyapunov control theory. The proposed controller eliminates the need for gains that are associated with cost function coefficients, as seen in classical model predictive control based controllers. Therefore, the control design problem is significantly simplified. In addition, the average switching frequency is also reduced, as shown in both simulation and experimental results, leading to a reduction in switching losses. Simulation and experimental tests, on a PUC7 lab prototype, demonstrate the excellent performance of the proposed control system, in terms of high disturbance rejection, robustness to parameter mismatches, and fast dynamic response. Such features qualify the proposed control strategy as a good candidate for grid-tied applications. [ABSTRACT FROM AUTHOR]

The magnetic resonant wireless power transfer (WPT) system with a class E inverter has wide application in mid-range power transmission, especially for several megahertz scenario. However, it is cumbersome for the existing modeling and analysis methods to obtain the analytical solution to the system variables, which limits the evaluation of system characteristic. This paper proposes a nonlinear mathematical model for the WPT system with a class E inverter. The equivalent small parameter method (ESPM) is first adopted to solve the proposed six-order nonlinear model, and symbolic-form steady-state periodic solutions are yielded. During the whole solving process, only three iteration steps are needed for the proposed method. Compared with other existing modeling and analysis methods, the symbolic periodic results acquired by the ESPM exhibit sufficient accuracy by virtue of the combination of more higher harmonics. Meanwhile, the calculation complexity is simplified remarkably. Simulation and available experiments validate the effectiveness and accuracy of the proposed method. [ABSTRACT FROM AUTHOR]

In this paper, a generalized switching modification method is proposed to reduce the root-mean-square (rms) current flowing into a dc-link capacitor in a dc–dc–ac structure consisting of a boost converter and a three-phase inverter. To analyze the current flowing into the capacitor, we analyze the currents at the respective converter and inverter sides. Based on this analysis, we derive an analytical method to find the modification time between the converter and inverter pulsewidth modulation (PWM) carriers through a Fourier series and approximation to facilitate real-time implementation. Real-time implementation of the modification time calculated by the derived method is described. To verify the validity of the proposed method, experimental results are presented based on a 1-kVA dc–dc–ac prototype. The proposed method has a better capacitor rms current reduction performance than the conventional method in various inverter power factors and PWM strategies. Especially, it has an excellent performance in mid-power factor level (0.95–0.1). [ABSTRACT FROM AUTHOR]

In this paper, an improved direct torque control (DTC) technique of a two-level inverter-fed five-phase induction motor (FPIM) drive for low-speed operation is presented. The operation of the FPIM with distributed winding requires the elimination of third-harmonic voltage, which, if not taken care of, would generate distorted stator current. For this, the concept of virtual vectors (VVs) is utilized. Before selecting the VVs for the DTC operation, a theoretical analysis is carried out to find the effects of these VVs on the torque and flux response of the FPIM under different speed and loading conditions. It is found that the rotor speed plays a crucial role in the selection of VVs. A particular VV has different effects on the torque change as speed varies. This analysis helps in the selection of VVs, hysteresis torque bandwidth, flux bandwidth, and efficient formation of sectors. Furthermore, in this paper, the performance of the FPIM during low-speed operation is improved by avoiding the demagnetization of the stator flux. To achieve this, a new modified lookup table is proposed. Superiority of the proposed method over the reported approaches is illustrated by experimental results. [ABSTRACT FROM PUBLISHER]

In this paper, a new topology for half-bridge Z-source inverter is proposed. The proposed topology has only one impedance network. Unlike to the conventional half-bridge inverter, the proposed topology can provide zero voltage level at the output. It also increases output voltage level and stabilizes it in the desired value. Capacitor voltage stress in the proposed topology is low, and, therefore, nominal voltage of capacitor and cost decreases. In this paper, the steady-state analysis of the proposed inverter in two new operations which are named synchronous operation of diodes and asynchronous operation of diodes is conducted based on mathematics calculations. A method to obtain high-voltage gains by cascading the Z-network and combining middle inductors is presented that leads to cost, size, and weight reduction. Comparison among the proposed converter with conventional ones shows its excellent performance. The experimental results have good agreement with analytical analysis for the proposed topology. [ABSTRACT FROM PUBLISHER]

Zero-common-mode-voltage (CMV) operation of multilevel inverters results in reduced dc-bus utilization and reduced linear modulation range. In this paper, a method to increase the linear modulation range for zero-CMV operation without increasing the dc-bus voltage using a cascaded multilevel inverter with a single dc supply is presented. Using this method, the peak fundamental output voltage can be increased from 0.499 to 0.637  \textV\text{dc} with zero CMV inside the linear modulation range. Also, various pulse width modulation (PWM) switching sequences are analyzed in this paper, and the PWM sequence that gives minimum current ripple is used for the zero-CMV operation of the inverter. The inverter topology with single dc supply is realized by cascading a two-level inverter with two floating-capacitor-fed full-bridge modules. Simulation and experimental results for steady-state and dynamic operating conditions are presented to validate the proposed method. [ABSTRACT FROM AUTHOR]

This paper presents a model predictive control technique applied to a dual-active bridge inverter where one of the bridges is floating. The proposed floating bridge topology eliminates the need for isolation transformer in a dual inverter system and therefore reduces the size, weight, and losses in the system. To achieve multilevel output voltage waveforms, the floating inverter dc-link capacitor is charged to the half of the main dc-link voltage. A finite-set model predictive control technique is used to control the load current of the converter as well as the floating capacitor voltage. Model predictive control does not require any switching sequence design or complex switching time calculations as used for space vector modulation; thus, the technique has some advantages in this application. A detailed analysis of the converter as well as the predictive control strategy is given in this paper. Simulation and experimental results to validate the approach are also presented. [ABSTRACT FROM PUBLISHER]

This paper presents a three-phase open-end winding induction motor drive. The drive consists of a three-phase induction machine with open stator phase windings and dual-bridge inverter supplied from a single dc voltage source. To achieve multilevel output voltage waveforms, a floating capacitor bank is used for the second of the dual bridges. The capacitor voltage is regulated using redundant switching states at half of the main dc-link voltage. This particular voltage ratio (2:1) is used to create a multilevel output voltage waveform with three levels. A modified modulation scheme is used to improve the waveform quality of this dual inverter. This paper also compares the losses in the dual-inverter system in contrast with a single-sided three-level neutral point clamped converter. Finally, detailed simulation and experimental results are presented for the motor drive operating as an open-loop v /f controlled motor drive and as a closed-loop field-oriented motor controller. [ABSTRACT FROM PUBLISHER]

Two three-level inverters driving an open-end winding induction motor can generate equivalent voltage waveforms as a single five-level inverter-based drive. In addition, it can bring in benefits such as reduced dc-link voltage, less number of devices, and fault-tolerant capability, which is favored in high-power motor drive applications. The main challenge with this type of configuration is the appearance of large zero-sequence current circulating between the two inverters, which generates extra losses in the switching devices and the motor as well as affects the normal operation of the machine. Another challenge is to balance the dc-link neutral point voltage of the two three-level inverters. This paper has proposed a simplified decoupled space-vector pulsewidth-modulation (PWM) strategy to eliminate the averaged zero-sequence voltage in each switching cycle by the placement of redundant vectors of each individual inverter using a time shift. Neutral point voltage balance is further achieved by adjusting the time duration of the redundant vectors. In this paper, it is shown that it is possible to operate this kind of drive configuration with a single dc power supply and achieve averaged zero-sequence voltage elimination and neutral-point voltage balancing at the same time. Experimental results of a 5.5-kW dual three-level inverter drive using the proposed PWM strategy are presented, which validates the control method and drive configuration. [ABSTRACT FROM PUBLISHER]

The carrier-based pulsewidth modulation (CBPWM) and virtual space vector pulsewidth modulation (VSVPWM) for neutral point clamped three-level converter are reviewed briefly in this paper. A novel modulation strategy is proposed to maintain unconditional neutral point voltage balance under the full range of power factor and modulation index. The proposed PWM strategy is featured with three switching actions in one switching cycle, which is named 3SNPBPWM hereafter. In 3SNPBPWM, one phase is clamped to a certain level without switching action, and the other two phases have one and two switching actions in one switching cycle (SC), respectively. Moreover, a neutral point voltage recovery algorithm for 3SNPBPWM is also proposed. The performance of 3SNPBPWM is analyzed and compared with CBPWM and VSVPWM in terms of switching loss, waveform quality, and ability of neutral point voltage recovery. Finally, the feasibility and superiority of 3SNPBPWM are verified by experiment. [ABSTRACT FROM AUTHOR]

This paper proposes a dual-function dynamic voltage restorer (DFDVR) with fault current-limiting capability. The new topology can operate under different modes: the short-circuit fault current-limiting mode and the compensation mode for voltage fluctuation. Different functions of the DFDVR are achieved by controlling a brake chopper circuit and antiparallel thyristors. During fault conditions, the antiparallel thyristors are deactivated to protect the dc-side capacitor, and the duration of the on- and off-periods of the semiconductor switch in the brake chopper circuit is controlled to adjust fault current amplitudes. During voltage sags, the antiparallel thyristors are activated, and the brake chopper circuit is turned off by controlling the gate turn-off thyristor in the brake chopper circuit, thus making the DFDVR similar to a conventional DVR. The control scheme and optimal parameter selection of the DFDVR are provided. The design methodology of the DFDVR was verified through simulations performed using the PSCAD/EMTDC software. The experimental results prove the capability and effectiveness of the DFDVR topology. [ABSTRACT FROM AUTHOR]

This paper presents a novel model predictive control (MPC) for the T-type single-phase three-level inverters. The cumbersome procedure in tuning of weighting factors is eliminated so that the implementation of the proposed MPC becomes easy. The constant switching frequency is achieved during the control implementation in order to facilitate the filter design. In order to optimize the distribution of the output current harmonics, multiple voltage vectors are employed in each control cycle with their application times setting inversely proportion to the respective cost function. The redundant small voltage vectors are utilized to balance the neutral point voltage of the inverter by directly regulating the upper and lower dc-link capacitors voltages. Finally, the proposed MPC algorithm is experimentally evaluated and compared with other two unfixed switching frequency MPC algorithms in terms of the steady state, transient performance, and parameter sensitivity. [ABSTRACT FROM AUTHOR]

In this paper, a new multi-input multi-output (MIMO) dc–dc converter with high step-up capability is proposed for wide power ranges. Also, in order to increase each output voltage, diode–capacitor voltage multiplier (VM) stages are utilized in the proposed converter. The number of input stages, output stages, and VM stages are arbitrary and dependent on design conditions. At first, the general structure of proposed MIMO converter is presented. Then, in order to explain the converter operation, we walk through the design of a 1-kW four-input two-output example, including loss and efficiency calculations. We validate the design with a prototype that matches efficiency calculations. [ABSTRACT FROM AUTHOR]

When fast voltage control is used in a power factor control, the ripple of the dc link causes current harmonics. This paper proposes a method to reduce the harmonic content of a fast voltage loop in a power factor correction, which can both produce low distortion during steady-state operation and fast recovery from a load transient. The performance is achieved by using a Takagi–Sugeno-type nonlinear controller for dc-link voltage control. The proposed nonlinear control is compared with linear proportional–integral (PI) control, which is tuned to meet the standardized regulations for the harmonic content in a 3-kW single phase power supply. The results show that the presented nonlinear voltage controller can maintain the dynamic performance of the linear control with reduced current harmonics. It is also shown that the used nonlinear control method requires only marginally more complex control algorithm compared to commonly used linear PI control. [ABSTRACT FROM AUTHOR]

This paper presents a new reconfiguration module for asymmetrical multilevel inverters in which the capacitors are used as the dc links to create the levels for staircase waveforms. This configuration of the multilevel converter makes a reduction in dc sources. On the other hand, it is possible to generate 13 levels with lower dc sources. The proposed module of the multilevel inverter generates 13 levels with two unequal dc sources (2VDC and 1VDC). It also involves two chargeable capacitors and 14 semiconductor switches. The capacitors are self-charging without any extra circuit. The lower number of components makes it desirable to be used in wide range of applications. The module is schematized as two back-to-back T-type inverters and some other switches around it. Also, it can be connected as a cascade modular which leads to a modular topology with more voltage levels at higher voltages. The proposed module makes the inherent creation of the negative voltage levels without any additional circuit (such as H-bridge circuit). Nearest level control switching modulation scheme is applied to achieve high-quality sinusoidal output voltage. Simulations are executed in MATLAB/Simulink and a prototype is implemented in the power electronics laboratory in which the simulation and experimental results show a good performance. [ABSTRACT FROM AUTHOR]

Due to the pulsating power at the inverter output terminals, the passive storage elements of the boost stage of the current-fed switched inverter (CFSI) contain a power frequency harmonic component (100 Hz), apart from dc and switching frequency components. In prior designs, the second harmonic component is suppressed by increasing the size of the input filter inductor and capacitor or by using additional circuits. This paper presents a complete characterization of a control-based approach to suppress the power frequency harmonic component in the input inductor current of a CFSI. It also presents a comprehensive characterization of the harmonic power redistribution. Using the proposed approach, it is demonstrated that the inductor value of a CFSI is reduced by 61% for the same peak-to-peak ripple. This leads to an improvement in the conversion ratio, efficiency, and power density of the overall converter. A SiC MOSFET-based CFSI with 75-kHz switching frequency is used to verify the proposed design philosophy. [ABSTRACT FROM AUTHOR]

This paper presents a high-efficiency inverter with the aid of the soft-switching technology, which is accomplished by the resonance of the in-series inductance with the snubber capacitance. The equivalent circuit of the quarter-phase ultrasonic motor is initially deduced, based on which the topology along with the operations of the novel inverter is subsequently presented. The configuration of the new quarter-phase inverter shows its uniqueness in terms of the shared arms and the especially designed snubber capacitance in comparison with the existing inverters. The circuit analysis infers that the dead time of the inverter is the key factor to arrive at the zero-voltage-switching or the zero-current-switching operations. Experimental measurements have demonstrated that the efficiency of the whole drive increases by a factor of 1.25 after replacing the traditional inverter with the proposed one. It should also be noted that the proposed inverter in association with the design method of the dead time not only can work for the quarter-phase ultrasonic motor, but also can be applicable for other kinds of quarter-phase devices. The soft-switching operations are achieved in the quarter-phase inverter for the first time, whose amplitudes of the output voltage and switching frequency are not required to be constant any more. [ABSTRACT FROM AUTHOR]

This paper explores a power-conversion system for single-phase transformerless ac module application. A nonisolated high-gain dc–dc stage is coupled with a doubly grounded dynamic dc-link inverter to implement the microinverter topology. The front-end boost stage steps up the single-module voltage to a higher dc voltage, typically to 200 or 400 V as required for the following inverter stage. It is a hybrid of an interleaved boost and switched capacitor concept capable of achieving high gain while simultaneously maintaining reduced voltage and current stress, and thus lowering switching and conduction loss for most of the switches. By directly connecting the grid neutral to the photovoltaic (PV) negative, the doubly grounded voltage swing inverter has the advantage of zero capacitive-coupled common-mode ground currents, critical for transformerless PV inverters. The two dc links of the inverter stage share the double-line frequency power decoupling with a combination of higher value of mean voltage and relatively large 120-Hz ripple component–the dynamic dc-link approach. Through an optimization algorithm, the decoupling capacitance is minimized enabling an all-film capacitor implementation while satisfying the converter's operating constraints over a wide range of power factors. The simulation as well as experimental results from a GaN-based hardware prototype validate the converter's performance. [ABSTRACT FROM AUTHOR]

The development of a photovoltaic ac module composed of a high static gain nonisolated dc–dc converter with current source output characteristic followed by an unfolding low-frequency inverter is presented in this paper. The operation of the dc–dc converter with high static gain and with reduced switch voltage is obtained using the Cuk converter integrated with the switched-inductor technique. The nonisolated structure allows the elimination of the volume and losses of the power transformer and leakage inductance, and an output filter configuration is proposed to reduce the high-frequency ground leakage current. The grid-tied inverter operating in a discontinuous conduction mode (DCM) allows a sinusoidal output current with low harmonic distortion (THD = 3.72%) to be obtained without current control loop and without the use of a current sensor at the output. The maximum power point tracking operation is obtained without the use of the current sensor. The DCM operation increases the current stress, but the proposed converter presents two switches and two input inductors sharing the input current in these components. The theoretical analysis, design procedure, and experimental results are presented for a prototype with a dc input voltage Vi = 30 V, an ac output voltage Vo = 127 V, and output power Po = 180 W. [ABSTRACT FROM AUTHOR]

This paper presents a five-phase dual random space vector pulsewidth modulation (FPDR-SVPWM) strategy with an optimized probability density function (PDF) for a five-phase voltage-source inverter, and its performance and evaluation are also analyzed. Based on the nearest four vectors modulation method, the FPDR-SVPWM strategy, combined with random switching frequency and random zero vector, is investigated to significantly reduce the amplitude of high-order harmonics near the switching frequency and its integer multiples. For the nonsinusoidal power supply, third harmonic injection is introduced in this modulation strategy as well. Considering the effect of random numbers on the performance, an optimized Beta distribution is studied in detail. In order to analyze harmonic dispersion degree qualitatively and quantitatively, the power spectral density and the harmonic spread factor are both employed to assess the performance of the FPDR-SVPWM strategy. A series of results of simulation in MATLAB and experiments based on field programmable gate array demonstrate that the proposed modulation strategy is correct and valid, and it distributes high-order harmonics into a wide range without affecting the fundamental wave and third harmonic. [ABSTRACT FROM AUTHOR]

To reduce the common-mode voltage (CMV) and eliminate the CMV spikes for two-level voltage source inverters (2L-VSIs), an improved model predictive control (MPC) based CMV reduction method is proposed in this paper considering dead-time effects. First, an improved voltage vector (VV) preselection strategy is proposed to reduce the CMV spikes caused by the dead time. Second, a new hybrid VV preselection strategy based on a delay compensation strategy and a modified current sector division strategy is proposed to completely eliminate the CMV spikes. As the proposed hybrid VV preselection based MPC strategy makes full use of the six nonzero VVs of the 2L-VSI, the current total harmonic distortions and ripples are reduced. The simulation and experiments are carried out to verify the effectiveness of the proposed strategy. [ABSTRACT FROM AUTHOR]

In this paper, a fixed switching frequency model predictive current controller is designed and implemented on a sensorless five-level packed U-cell (PUC5) inverter interfacing the utility. The predictive control methodology is based on a voltage vector generation technique for the cost function optimization by nullifying its derivative. The aim of the controller is to allow a fixed-frequency operation with no iterations while operating as a utility line current regulator. A pulsewidth modulator based on employing PUC5 redundant switching states fixes the PUC5 auxiliary dc bus capacitor voltage to its desired level with no necessity of a regulator; the overall technique reduces system complexity with less sensors and no loops in the predictive algorithm making it suitable for industrial applications. System discrete model is developed and experimental results verify the performance of the designed controller in making a fast response in regulating the grid current and balancing the capacitor voltage. [ABSTRACT FROM AUTHOR]

To solve the problem of poor robustness due to the high dependence of model predictive control (MPC) on the three-phase inverter model, the influence mechanism of the mismatch of circuit parameters R and L, the model discretization error, and sampling errors on MPC prediction error are analyzed in this paper. A feedback self-correction is proposed, which the next current errors are predicted and used to modify the model, based on the previous prediction errors. This proposed method involves simple structure and a small amount of calculation. Steady-state effects of the proposed method are quantized to prove a good inhibitory ability on multifactorial prediction errors. Finally, experimental results in a three-phase inverter are presented to support the theoretical analysis and demonstrate the feasibility of the proposed method. [ABSTRACT FROM AUTHOR]

Multilevel inverters are now-a-days being applied in electric vehicles (EV). Considering the dynamic operating conditions of an EV propelled by an induction motor, this paper proposes a flexible discontinuous modulation strategy for three-level neutral-point-clamped (NPC) inverter that can shift modulation pattern seamlessly from sinusoidal pulsewidth modulation (SPWM) to discontinuous PWM (DPWM). The modulation scheme is generalized at each degree of discontinuity to ensure minimum switching losses for variable load power factors. Additionally, a hybrid voltage balancing strategy, which comprises two sets of compensating offset signals with complementary features, has been introduced to mitigate voltage deviation problem at neutral point of the inverter. The unique feature of the proposed hybrid balancing approach is that it generates uniform compensating neutral current regardless of the level of discontinuity. This results in identical and predictable voltage balancing dynamics for the entire modulation transition covering SPWM and DPWM. It has been shown that the proposed hybrid balancing strategy does not lose its unbalance compensation strength even during transition from one modulation pattern to another. The effectiveness of the proposed scheme for wide variations in operating conditions is studied through extensive simulation, and validated in experimentation using a prototype NPC inverter with induction motor loads. [ABSTRACT FROM AUTHOR]

Wireless power transfer with a self-tuning LCC inverter using pulsewidth modulation (PWM) controlled switched capacitor is proposed in this paper in order to compensate for the variations of Tx inductance. Usually, receivers contain magnetic and conductive materials for shielding and mechanical support. The inductance of the Tx coil is sensitive to the variation of Tx–Rx alignment because the interaction between the Tx coil and the Rx magnetic–conductive materials is also varied. It is shown that the detuning of the Tx inductance value exacerbates the losses in the LCC inverter. In the proposed method, the PWM duty ratio of a single capacitor adjusts the effective output impedance of the LCC inverter. The PWM feedback loop is designed such that the power factor and the real-part impedance of the LCC inverter are maximized. The PWM switch is turned on at zero voltage and turned off with low dv/dt, minimizing switching losses. Such a soft-switching tunable capacitor can handle higher power compared to the traditional hard-switching capacitor, p-n junction capacitor, or an analog IC capacitor. Another advantage of the proposed technique is the continuity in achievable capacitance value using only one capacitor. The feedback can be fully implemented by analog components, obviating the necessity of digital samplings, ADC/DACs, and microcontrollers. The power of 54 W is transferred at 76.6% and 60.7% with and without the proposed method, respectively. [ABSTRACT FROM AUTHOR]

Soft-switching inverters can achieve high efficiencies and low switchdv/dtanddi/dt, but often impose additional stress on the switches due to their resonant behavior. Multicell converters, on the other hand, can process high voltages by arranging the switches to share the stress. This paper proposes a buck–boost multicell soft-switching inverter with inherent cell voltage balancing. Both the current and voltage stresses are shared by the cells. Soft-switching conditions are achieved for all switching transitions without any need for auxiliary circuitry or clamps. A multiple-winding transformer transfers energy between the terminals and provides galvanic isolation. An analytical study and experimental results on a 1200-W prototype verify the operation of the inverter. [ABSTRACT FROM AUTHOR]

In this paper, a fast and practical method is proposed for open-circuit (OC) fault diagnosis (FD) in a three-phase quasi-Z-source inverter (q-ZSI). Compared with the existing fast OC FD techniques in three-phase voltage source inverters, this method is more cost-effective since no ultrafast processor or high-speed measurement is required. Additionally, the method is independent of the load condition. The proposed method is only applicable to Z-source family inverters and is based on observing the effect of shoot-through intervals on the system variables during switching periods. The proposed algorithm includes two consecutive stages: OC detection and fault location identification. When both stages of the OC FD algorithm are done, a redundant leg is activated and utilized instead of the failed leg. The accuracy of the proposed method is confirmed by the experimental results from a low-voltage q-ZSI prototype. [ABSTRACT FROM AUTHOR]

Recently, a few fault-tolerant control strategies have been proposed for T-type three-level inverters to improve the reliability of the inverter system. However, the neutral-point (NP) voltage oscillations suppression is never considered in the previous fault-tolerant control strategies. In order to suppress the NP voltage oscillations when open-circuit fault occurs to NP switches, this paper proposes two novel fault-tolerant control strategies named as improved two-level switching tolerant control and hybrid switching tolerant control (HS-TC). Both methods are implemented by adding an optimal time-offset to the three-phase turn-ontimes. The corresponding time-offset value of each method is simply calculated considering the phase current and dwell time of [O] state. Moreover, an NP voltage balancing algorithm to eliminate the dc deviation and a dc bias to further reduce the NP voltage oscillations are used in the HS-TC. The performance and comparison of the tolerant controls with respect to the NP voltage oscillations, current total harmonic distortion, and dynamic response are illustrated and analyzed through the simulation and experimental results. [ABSTRACT FROM AUTHOR]

This paper proposes advanced speed control for a five-leg voltage source inverter (FLVSI) that drives the dual three-phase induction motor system used in industrial manufacturing processes. The advanced speed control method consists of two controllers: 1) The first is a slip controller that satisfies the application requirement, i.e., to control the mechanical speed of two motors equally regardless of the load condition. 2) The second is an angle controller that satisfies the FLVSI requirement, i.e., to control the phase angle difference between the two motors for minimizing the common leg current because the common leg current can be twice higher than other leg's current depending on the operation condition of the dual motor. Stability analysis of the two controllers under advanced speed control is implemented, and the whole performance of the advanced speed control for the FLVSI-fed dual-motor drive system is shown to identify its feasibility through the experimental results. [ABSTRACT FROM AUTHOR]

This paper proposes a transformerless line-interactive uninterruptible power supply (UPS) with low ground leakage current. A high-efficiency bidirectional inverter is suggested, which performs the line-interactive UPS functions with low ground leakage current. It has a full-bridge inverter and a bidirectional switch, which operate with the unipolar pulsewidth modulation. Because the bidirectional switch operates at the line-frequency, switching losses can be lower than the previous transformerless inverters. As the inverter operates, the parasitic capacitance between the inverter and the ac voltage ground is clamped to zero voltage for a positive line cycle and to the ac voltage for a negative line cycle, respectively. Thus, the parasitic capacitance can be prevented from being charged or discharged, which ensures the absence of the ground leakage current. The operation modes of the proposed system are described. The control schemes are presented to design the proposed inverter for the line-interactive UPS. Experimental results for a 2.0 kW prototype are discussed to verify the performance of the proposed system. [ABSTRACT FROM AUTHOR]

In this paper, a three-level quasi-switched boost T-type inverter (3L qSBT2I) is proposed. A new pulse-width modulated (PWM) control method is presented to reduce the inductor current ripple of the qSBT2 I. In the introduced PWM technique, the shoot-through duty cycle is maintained constant to keep the modulation index as high as possible. Then, the only control parameters of the qSBT2I are the duty cycles of the two additional switches. By controlling the duty cycles of the two additional switches, the voltage gain of the proposed qSBT2 I can be improved to a value larger than that of the conventional 3L impedance source inverters. The steady-state analysis, operating principles, and comparisons with the impedance source-based 3L inverters are presented. A 1-kW prototype is constructed to verify the operating principle of the 3L qSBT2I. An indirect dc-link voltage regulator and a capacitor voltage-balance controller are applied to the proposed qSBT2I. Simulation and experimental results are presented. [ABSTRACT FROM AUTHOR]

This paper proposes a zero-sequence circulating current (ZSCC) control scheme for the multiparalleled three-level T-type inverters (3LT2Is). Based on the analysis with the proposed generalized model of multiparalleled 3LT2Is, it is seen that the ZSCC is influenced by the circuit parameters, duty cycles, and the circulating currents of the l th and first 3LT2I. To mitigate the circulating currents, a deadbeat control strategy for n-paralleled (n≥3) inverters is proposed, which is realized by adjusting the duty cycle of the small vectors in each PWM sampling period. Compared with the conventional PI control method, the ZSCC spike is mitigated with the proposed scheme, thus improving the quality of the output currents. Also, the reliability of the 3LT2Is system is improved because such a scheme only needs the information about the ZSCC and zero-sequence duty ratio in the l th and the first inverter. The proposed method can also be applied to the neutral-point-clamped converters. Simulation and experimental results verify the effectiveness of the theoretical analysis and the proposed method. [ABSTRACT FROM PUBLISHER]

Microinverters operating into the single-phase grid from new energy source with low-voltage output face the challenges of efficiency bottleneck and twice-line-frequency variation. This paper proposed a multilevel inverter based on bridge modular switched-capacitor (BMSC) circuits with its superiority in conversion efficiency and power density. The topology is composed of dc–dc and dc–ac stages with independent control for each stage, aiming to improve system stability and simplify the control method. The BMSC dc–dc stage, which can be expanded to synthesize more levels, not only features multilevel voltage gain but also partially replaces the original bulk input capacitor and functions as an active energy buffer to enhance power-decoupling ability between dc and ac sides. In dc–ac stage, the control strategy of optimized unipolar frequency doubling sine-wave pulse width modulation is proposed to improve the quality of output waveform. Meanwhile, the multilevel voltage phase has been optimized to further reduce the power loss. Finally, a prototype has been built and tested. Associated with the simulation, the experimental results validate the practicability of these analyses. [ABSTRACT FROM PUBLISHER]

This paper characterizes the sampling effect in digital sinusoidal pulse width modulation (SPWM) of voltage source inverter (VSI). The time-domain analysis presented in this paper establishes the relation between the fundamental frequency, carrier frequency, and the sampling frequency at different modulation indices of the SPWM. The analysis investigates the effect of sampling frequency of the digital controller on the output of the VSI. It is shown that the low-frequency harmonic components appear in the frequency spectrum of the VSI output voltage due to sampling. As a result, the output current of digitally controlled VSI is stepped in nature. The double Fourier integral solution of the switched waveform for inner and outer integral limits has been used to derive the expression. The integral solution is obtained using Jacobi-Anger expansions. The generalized results developed in this paper are useful to investigate the sampling effect in high switching frequency DSPWM. The proposed sampling effect has been analyzed for SPWM of single-phase H-bridge inverter. The analytical results are verified using simulation and experimental results. The experimental results have been obtained with the use of field-programmable gate array (FPGA) as a digital controller. [ABSTRACT FROM PUBLISHER]

A new pulsewidth modulation (PWM) strategy which is an alternative approach of the discontinuous PWM (DPWM) for a three-level neutral-point-clamped (NPC) inverter is proposed in this paper. A three-level NPC inverter is completely mature and very well-established topology in high-power applications. However, the three-level NPC inverter has an inheritance problem of the neutral-point voltage unbalancing due to the split dc-link capacitors. This structure can cause large neutral-point voltage ripple. Furthermore, output currents of the three-level NPC inverter are distorted by the neutral-point voltage ripple. Therefore, the neutral-point voltage must be controlled. In this paper, a new DPWM method using two different offsets for the neutral-point ripple reduction is proposed and the effectiveness of the proposed DPWM method is verified by using the simulation and the experimental results. [ABSTRACT FROM PUBLISHER]

A four-level five-phase open-end winding (OeW) drive topology is introduced in this paper. The drive comprises a five-phase induction machine with open-end stator windings, supplied using two two-level voltage-source inverters with isolated and unequal dc-link voltages, in the ratio 2 : 1. The topology offers the advantages of a modular structure with fewer semiconductor components and has a greater potential for fault tolerance, as compared with an equivalent single-sided four-level drive. Due to the large number of switching states, development of a suitable space vector pulsewidth-modulation (PWM) method can be challenging. Hence, this paper examines the implementation of two-level-shifted carrier-based PWM methods. The effect of dead time on the drive performance is discussed, and it is shown that simultaneous PWM switching of both inverters can lead to degraded output phase voltage waveforms. Detailed analysis of this phenomenon is presented, a solution is proposed, and the modified modulation techniques are incorporated in an experimental setup, at first in conjunction with $V/f$ control. Once the proof of concept has been provided, full field-oriented control is implemented in this OeW drive topology for the first time; detailed experimental testing is conducted, and results are reported. [ABSTRACT FROM AUTHOR]

A merit of the interleaving reducing the switching harmonics allows for the reduction of the filter inductance. However, in the case of direct parallel voltage source inverters (VSIs), a severe circulating current occurs. To suppress the high frequency circulating current, coupled inductors (CIs) for the high impedance is inserted. However, the employed CIs induce a positive- or negative-sequence circulating current (i.e., a cross current) besides the zero-sequence circulating current already mentioned in the other papers. Due to different impedances developed by the current characteristics and the cross current in the CIs, VSIs becomes unstable when the resonant controllers are applied for the harmonic compensation such as 5, and 7th harmonics. In this paper, the cross currents and the impedances of CIs varying with the current characteristics are mathematically analyzed, and a novel current controller is proposed to solve this stability problem. The experimental results validate the proposed control scheme. [ABSTRACT FROM PUBLISHER]