Search

This paper presents an artificially intelligent Flash ADC with enhanced resolution from 4 to 10 bits. Unlike conventional approaches, this artificial intelligence (AI)‐based architecture avoids the use of many number of comparators in the Flash ADC when the ADC's resolution changes from 4 to 10 bits. This work initially gets the digital output of a 4‐bit existing Flash ADC as a training data set and then uses these 4‐bit output bits and sends to resolution enhancement logic (REL) block to vary its resolution without increasing the hardware complexities. After simulation, it is observed that the proposed ADC is of SNR of 24.13 dB for 4‐bit Flash ADC designed in SCL 180 nm CMOS technology and increases from 36.89 to 60.70 dB for 6 to 10‐bit resolution, respectively. The sampling frequency of the proposed architecture ranges from 3.6 to 1.04 GHz for a change in resolution from 4 to 10 bits. The FoM of 235 fJ/conv‐step in the training phase is obtained, and it varies from 56 to 20.3 fJ/conv‐step in the next phase of the testing and the prediction. The estimated area of the proposed 4‐to‐10‐bit variable resolution Flash ADC is 235.23×301.67 μm2. [ABSTRACT FROM AUTHOR]

This paper presents a novel jitter reduction technique for a voltage-controlled ring oscillator (VCRO). This technique is helpful in employing VCRO-based circuits like Analog to Digital Converter (ADC), Phase Locked Loop (PLL) and time-based circuits whose performance is severely degraded by high jitter. In the proposed technique, the jitter is extracted using Excess Phase Discrimination (EPD) block and is transformed into Pulse Width Modulated (PWM) signal, which is then fed into the Phase Compensator (PC) block. This block reduces the jitter by about half its value after enabling the Single Ended Injection Locking (SEIL). The proposed work is designed in SCL 180 nm CMOS technology at 1.8 V supply. On enabling the proposed circuit, the Root Mean Square (RMS) jitter reduces from 5.94 to 2.58 ps (about 56%) for VCRO running at 58 MHz and consumes a total power of 375.84 μ W. The overall performance of the proposed circuit does not vary much in the post-layout simulations, hence demonstrating the effectiveness of the proposed technique. [ABSTRACT FROM AUTHOR]

Introduction: Though, having right set of behavioural skills is always been a priority of all organizations, nevertheless, today's organizations are investing too much on behavioural skill training to safeguard their brand value, bring-up the work culture, maintaining reputation, etc. Behavioural skills plays a vital role in personal development and well-being at student level also. This paper identifies and analyzes the fourteen behavioural skills which are vital in the personal and professional excellence development of a student. Methods: Exhaustive literature review is done and expert opinions are taken to determine the behavioural skills. Interpretive Structural Modelling is performed to analyze and prioritize these skills into strategic, operational and performance outcomes. Results: Behavioral skills are not only depicted in ones' actions but also determines thought process and attitude of a person. Result of this research shows that time management, emotional intelligence, self-development, resilience, multitasking, and open mindedness of an individual are the key behavioural skills that trigger most behaviours and eventually influences the effectiveness of management of personal and professional life. Discussion: Every job requires specific skills to perform. There are certain skills that must be possessed by every student irrespective of the discipline. It include behavioural skills like human values, resilience, multitasking, communication, etc. Research on behavioral skills and its importance are available in literature. However, the literature is lacking in explaining the interplay of these skills in driving personal and professional journey of an individual. Such skills may not be mentioned in the recruitment advertisements but are vital to perform well. [ABSTRACT FROM AUTHOR]

The paper demonstrates an efficient process flow for the Hardware Testing of an ASIC (Application Specific Integrated Circuit). The procedure is implied on Comparator, ADC (Analog-to-Digital) and Present Cipher Crypto ASIC. This involves the testing functionality of an Analog, Digital and Mixed Signal design ASIC. The results obtained during functional testing are verified through simulations on Cadence, in case of comparator and ADC ASIC, and vivado in case of Crypto ASIC. The method gives high accuracy and requires less power even at high frequency. [ABSTRACT FROM AUTHOR]

A dual‐loop ADPLL architecture with 3‐bit flash TDC and background calibration‐based VCO is presented in this paper. The major aim of this work is to achieve the low jitter, low power, fast locking, and PVT‐insensitive ADPLL using simple flash TDC and gain calibrated VCO. A simple flash‐based 3‐bit TDC in the main loop is used which helps in achieving the fast locking with lower power consumption in ADPLL. The novel low phase noise VCO, with gain calibration in another loop, is used to fasten the locking process and jitter reduction due to any PVT variations. Therefore, both flash TDC and dual loop in the proposed ADPLL architecture help in achieving the fast locking. Proposed ADPLL is designed in SCL 180 nm CMOS technology at 1.8 V. The resolution of 3‐bit flash TDC is 3 ps. The achieved jitter of ADPLL is 1.83 ps with a phase noise of −153 dBc/Hz and locking time of 1.7 μs. Total power consumption is 5.3 mW at a frequency of 1.6 GHz. [ABSTRACT FROM AUTHOR]

This paper presents a scalable Fully-digital differential analog voltage comparator designed in Semi-Conductor Laboratory (SCL) 180 nm complementary metal-oxide semiconductor technology. The proposed design is based on a digital design approach and is easily configurable to lower technology nodes. This design methodology makes the circuit less sensitive to process variations and takes fewer design efforts suitable for Systems-on-a-Chips (SOCs) application. The proposed circuit is designed and simulated in Cadence Virtuoso Analog Design Environment at the supply voltage ranging from 1 V to 1.8 V. The fully-digital analog voltage comparator has been synthesized using Synopsys Design Vision and auto-placed & auto-routed using Synopsys IC Compiler. This proposed comparator has a resolution of up to 7-bit at a supply voltage of 1.8 V and a worst-case operating frequency of about 750 MHz at the TT corner. The obtained value of the offset voltage and delay is 0.55 mV and 0.72 ns, respectively. The simulated results have shown that the power dissipation of the proposed scalable analog voltage comparator is 1 5 0 μ W @ 1 V and 3 1 2 μ W @ 1. 8 V supply voltage, respectively. Also, the RC extracted post-layout simulations have been implemented to verify the performance, which does not affect the results much. [ABSTRACT FROM AUTHOR]

Over the last two decades, an exponential rise has been observed in the growth of spiritual tourism where travellers are preferring and visiting places of religious inclination seeking to align their body and mind. In the current fast paced life where stress, anxiety, insecurities and depression have become common place, travelling to certain places that provide connection with the almighty or peace to the traveller has become very important. Spiritual tourism in India has always been very highly valued and is active as an industry in a country known as the land of temples and gods. Many globally popular destinations exist in India that attract both domestic and international travellers alike. Destinations like Puri Jagannath, Kedarnath, Amarnath Yatra, Rishikesh, Varanasi, and Haridwar have developed their image and branding power over the years for the peace and meditating impact they have on their tourists. This trend has also been enhanced by the overall image of India as a country for religious and spiritual tourism where lakhs of international tourist come for relaxation and peace. The transformation of social media platforms has had an important and significant impact on the destination branding of spiritual locations and the final decision making of travellers. As travellers are active on social media platforms in sharing their stories of travel, sharing posts and videos, highlighting their travel, they are sharing their experiences with a large community. Thus, social media impacts on decision making for spiritual destinations needs to be studied in depth to understand the underlying factors that impact the final decision. For the purpose of this paper, various variables are analysed through the SEM framework to determine their interdependency and how they influence the final decision of the tourist. The study is important for academics in tourism as it discusses the most relevant examples and key factors. The study is also meaningful to practitioners of tourism who can ensure that the correct social media marketing can be undertaken for attracting tourists to spiritual destinations. [ABSTRACT FROM AUTHOR]

A voltage supply scalable analog voltage comparator for a wide input range is presented in this paper. A digital gate-based methodology is used to design the comparator in order to extend the use of automation in the analog designs. Therefore, the proposed comparator is enormously cost-effective, reduces the time-to-market, scalable to newer technologies, and more immune to process variations than the conventional CMOS analog voltage comparators. The comparator is designed using Semi-Conductor Laboratory (SCL) 180 nm digital CMOS technology at a supply voltage of 1.8 V. The power consumption of the proposed comparator is 160 µW approximately with total delay and offset voltage of 1.63 ns and 4.28 mV, respectively. Also, 4-bit and 5-bit flash ADC is designed as an application. The measured values of DNL/INL are ± 0.4/± 0.4 LSB and 0.42/± 0.6 LSB for 4-bit and 5-bit, respectively. [ABSTRACT FROM AUTHOR]

This paper aims at designing a digital approach based low jitter, smaller area and wide frequency range phase locked loop (PLL) to reduce the design efforts and power which can be used in System-on-chip applications for operating frequency in the range of 0.025–1.6 GHz. The low power, scalable and compact charge pump is proposed which reduces the overall power consumption and area of proposed PLL. A frequency phase detector (PFD) based on inverters and tri-state buffers have been proposed for the PLL. It is fast which improves the locking time of PLL. Also, pseudo-differential voltage controlled oscillator (VCO) is designed with CMOS inverter gates. The inverters are used as phase interpolator to maintain the phase difference of 180∘ between two outputs of VCO. Also, the inverters are used as variable capacitors to vary the frequency of proposed VCO with control voltage. It demonstrates the good phase noise performance enabling proposed PLL to have low jitter and wide frequency range. All the major blocks like PFD, charge pump and VCO are designed using digital gate methodology thus saving area and power and also reduce design efforts. Also, these digitally designed blocks enable the PLL to have low jitter small area and wide range. The proposed PLL is designed in a 0.18- μ m CMOS technology with supply voltage of 1.8 V. The output clocks with cycle-to-cycle jitter of 2.13 ps at 1.6 GHz. The phase noise of VCO is − 137 dBc/Hz at an offset of 100 MHz and total power consumed by the proposed PLL is 2.63 mW at 1.6 GHz. [ABSTRACT FROM AUTHOR]

A fast phase frequency detector (PFD) and low gain low phase noise voltage-controlled oscillator (VCO)-based phase-locked loop (PLL) design are presented in this paper. PLL works in the frequency range of 0.025–1.6 GHz, targeting various SoC applications. The proposed PFD, designed using CMOS dynamic logic, is fast and improves the locking time, dead zone and blind zone in the PLL. The standard CMOS inverter gate-based pseudo differential VCO is used in the PLL. Also, CMOS inverter is used as variable capacitor to tune the frequency of VCO with control voltage. The proposed PLL is designed in a 180 nm CMOS process with supply voltage of 1.8 V. The phase noise of VCO is − 1 3 7 dBc/Hz at an offset frequency of 100 MHz. The reference clock of 25 MHz synthesizes the output clock of 1.6 GHz with rms jitter of 0.642 ps. [ABSTRACT FROM AUTHOR]

A 4-bit flash ADC utilizing the advantage of digital-based differential voltage comparator is presented in this paper. This circuit has an advantage of digital circuit concept and can be easily migrated to lower technologies. Also, the digital circuits are less sensitive to the noise and device mismatches can be synthesized and auto place and route (P&R) using EDA tools. The design of the proposed comparator is based on the standard cells implementation. As the proof of concept this comparator is implemented on Xilinx Basys-3 Artix-7 FPGA kit. The prototype of complete 4-bit Flash ADC is designed in 180 nm CMOS technology with 1.8 V supply voltage. The measured values of ENOB, SNDR, SNR and SFDR are 3.6, 23.43 dB, 25.2 dB and 30.1 dB, respectively at 33.20 MHz input frequency and 200 MHz clock frequency. The total power consumed by the 4-bit flash ADC is 2.14 mW. The calculated value of DNL and INL is < 0. 4 LSB and < 0. 5 LSB respectively. [ABSTRACT FROM AUTHOR]

Here, a fast digital foreground calibration technique to calibrate the gain error in the pipelined analogue‐to‐digital converter (ADC) is proposed. The technique suggested uses maximum reference value of the ADC along with least mean squares adaptive algorithm to compensate the gain error. It avoids the use of slow but accurate reference ADC, thus saving area, power, and design efforts. The proposed calibration algorithm is implemented in Xilinx Artix‐7 FPGA kit to show the effectiveness of the algorithm. After calibration, differential non‐linearity improves by 30% and integral non‐linearity reduces from values +60/−60 LSB to +0.77/–0.77 LSB. Also, signal to noise and distortion ratio and spurious‐free dynamic range improve significantly from 35.9193 and 36.7348 to 75.3619 and 82.2884 dB, respectively, after calibration. [ABSTRACT FROM AUTHOR]

This study describes the highly‐digital 4‐bit 200 MS flash analogue to digital converter (ADC) whose major part can be digitally synthesised thus achieving low power, reducing the time‐to‐market and is scalable with technology. The comparators used in the ADC consist of complementary metal–oxide–semiconductor (CMOS)‐based inverter and NAND‐NOR as standard cells. The complete flash ADC is designed in 180 nm CMOS technology with 1.8 V supply with the power consumption of 4.51 mW. The signal‐to‐noise and distortion ratio, signal‐to‐noise ratio and spurious‐free dynamic range are equal to 23.3, 25.2 and 30.1 dB. It provides an effective number of bits equal to 3.5. The differential non‐linearity (DNL) of this ADC is ± 0.25 LSB and integral non‐linearity (INL) is + 0.6 LSB. [ABSTRACT FROM AUTHOR]

A 10‐bit pipelined analogue‐to‐digital converter (ADC) at a sampling rate of 100 MS/s utilising only metal–oxide–semiconductor (MOS) transistors is presented and designed in 1.8 V 0.18 μm standard digital complementary MOS (CMOS) n‐well technology. The internal gain of value 2 of the intermediate stages is achieved by using a charge‐pump‐based concept that avoids the use of power‐area inefficient operational amplifier. All the capacitors are realised by capacitors implemented by metal–oxide–semiconductor field‐effect transistors (MOSCAPs) that allows easy integration with any inexpensive standard digital CMOS technology, and altogether giving low area‐power‐cost solution. A low DC gain CMOS differential amplifier in source follower configuration is used and low gain effects are calibrated digitally in the background. Peak differential non‐linearity (DNL) improves from −1/+0.27 least significant bit (LSB) to −0.43/+0.57 LSB and peak integral non‐linearity (INL) is reduced from −9.56/+9.3 LSB to within range of ±0.5 LSB after calibration. Also signal‐to‐noise plus distortion ratio (SNDR) and spurious‐free dynamic range (SFDR) increase to 65.4 and 72.08 dB, respectively, after calibration. [ABSTRACT FROM AUTHOR]

A power and area efficient metal-oxide semiconductor field-effect transistor (MOSFET)-only 1.5-bit fully differential pipelined analog-to-digital converter (ADC) stage is proposed and designed in TSMC 0.18 μm digital CMOS technology with supply voltage of 1.8 V. It is based on charge pump based technique to achieve the stage voltage gain of 2. Various capacitances are implemented by MOSCAPs (capacitance offered by the MOSFET), offering compatibility with cheaper digital complimentary metal-oxide semiconductor (CMOS) process in order to reduce the much required manufacturing cost. The proposed stage suffers from only linear gain error with full signal swing of 2 V peak-to-peak (p–p) differential. Using the proposed stage, un-calibrated signal-to-noise and distortion ratio (SNDR) and spurious-free dynamic range (SFDR) for 10-bit, 100 MS/s pipelined ADC are 40.11 and 40.86 dB, respectively, which can be further increased by using a simple digital calibration technique. Comparison between the proposed stage and conventional operational amplifier based stage shows insensitivity towards capacitor mismatch along with power savings and design simplicity. [ABSTRACT FROM AUTHOR]