Search

A normally-off SiC-JFET/GaN-HEMT cascode device is recently proposed, featuring a cascode configuration that incorporates a high-voltage (HV, e.g., 1200 V) silicon-carbide (SiC) junction field effect transistor (JFET) delivering the HV blocking capability and a low-voltage (LV) enhanced-mode (E-mode) gallium-nitride (GaN) high electron mobility transistor (HEMT) providing the normally-off gate control. This all-wide-bandgap device exhibits superior thermal stability and high switching speed compared to its counterparts, e.g., the SiC/Si cascode device. In this article, we study short-circuit (SC) characteristics of a 1200-V/80-mΩ SiC/GaN cascode device by considering the interactions between the SiC and GaN devices. The single-event SC withstand time (SCWT) of the demonstrated SiC/GaN cascode device is tested to be ∼3 μs under a dc-bus voltage (Vdc) of 600 V when the turn-on gate voltage (VG-on) is set to 5 V. The SC failure occurs due to the formation of hot spots induced by thermal-runaway leakage currents inside the SiC JFET. The SCWT of the cascode device could be improved by applying a moderate VG-on (e.g., SCWT = ∼6.5 μs at VG-on = 3.5 V under v dc = 600 V) without affecting the on-state resistance (r on). However, it is identified that current oscillations tend to be triggered during the SC period when VG-on is too low (e.g., lower than 3 V). The oscillation behavior is attributed to the energy stored in the interconnection parts between the SiC and GaN devices. The harmful oscillations could be suppressed by applying higher VG-on, which drives the SiC JFET into low-transconductance mode by modulating the drain-to-source voltage (VDS-G) of the LV GaN HEMT. [ABSTRACT FROM AUTHOR]

A 650-V/84-mΩ normally-off GaN/SiC cascode device is demonstrated with systematic static and dynamic characterizations. The cascode device features a low-voltage enhancement-mode (E-mode) gallium nitride (GaN) high electron mobility transistor (HEMT) to enable normally-off gate control, and a 650-V normally-on silicon carbide (SiC) JFET provides the high-voltage blocking capability. The GaN/SiC cascode device exhibits many application-desired behaviors, including reverse conduction capability, avalanche breakdown capability, thermally stable threshold voltage, low input/output capacitances, no dynamic RON degradation, and negligible dynamic VTH shift. In addition, a customized double-pulse test board is built to evaluate the switching performance of this cascode device and other 650-V SiC-based power devices. This cascode device adopting low-voltage GaN HEMT has low QG×RON and exhibits excellent switching performance. The switching losses (EON and EOFF) are much smaller than that of the 650-V Si/SiC cascode device and comparable to that of the state-of-the-art 650-V SiC MOSFETs. [ABSTRACT FROM AUTHOR]

A cost-effective engineered bulk silicon (EBUS) substrate technology is presented, featuring p-n junction implemented on bulk Si substrates using mainstream ion implantation and thermal annealing processes. Standard p-GaN/AlGaN/GaN heterostructures are successfully grown on the EBUS substrate and used to fabricate 200-V enhancement-mode p-GaN gate HEMTs. By creating deep trenches in the EBUS substrate to isolate the local P+ silicon regions underneath the high-side (HS) and low-side (LS) power switches, adverse effects (e.g., back-gating and dynamic ON-resistance degradation) in the use of conventional bulk Si substrate are all eliminated. The mechanism of crosstalk suppression in the GaN-on-EBUS platform is revealed in comparison with conventional GaN-on-Si platform and verified by a series of designed tests. [ABSTRACT FROM AUTHOR]

Although the gallium nitride (GaN) high-electron-mobility transistor/silicon carbide (SiC) junction field-effect transistor (JFET) cascode device exhibits certain performance advantages over the SiC metal–oxide–semiconductor field-effect transistor (MOSFET), its robustness in harsh operating conditions is unknown. In this work, the short-circuit (SC) robustness of 650-V GaN/SiC cascode devices is characterized, analyzed, and compared with that of several mainstream SiC MOSFETs. GaN/SiC cascode devices exhibit competitive SC capability. Different failure modes are observed: thermal runaway in the SiC JFET of the cascode device and gate-to-source breakdown in the SiC MOSFET. The difference is associated with the configuration of the dielectric above SiC in the JFET and the source pad layout. According to the waveforms in SC events, failure spots, and thermal simulation results, a thermal runaway in the SiC JFET is attributed to the positive feedback between the drain leakage current and the junction temperature in the local area (hotspot) without the source pad on the top. The SC withstand time of the cascode device can be extended by reduction of the active area without the source pad. [ABSTRACT FROM AUTHOR]

In this article, the impacts of the off-state gate bias (VGS,OFF) on dynamic on-resistance (RON) are systematically investigated in commercial Schottky-type p-GaN Gate high-electron-mobility transistors. Double-pulse tester and pulsed I–V system are adopted to evaluate the dynamic RON with various off-state gate and drain bias (VDS,OFF) under hard- and soft-switching conditions. More negative VGS,OFF can aggravate the dynamic RON degradation under both soft- and hard-switching, especially when switching with a high VDS,OFF. The impacts of VGS,OFF on switching transients and off-state stress are investigated separately to reveal the underlying mechanisms, which are found to be associated with the generation and movements of holes. The off-state gate bias of the voltage-driving scheme needs to be carefully considered according to the identified mechanisms in terms of dynamic on-resistance degradation. [ABSTRACT FROM AUTHOR]

We report GaN high-electron-mobility transistors (HEMTs) with a thick (7.7 µm) GaN buffer on a Czochralski low resistivity Si (LRS) substrate. The GaN HEMTs exhibit high performance for both radio-frequency (RF) amplification and power conversion. The thick GaN buffer was grown by means of vacancy engineering, delivering a low dislocation density of ∼1.6 × 108 cm−2, contributing to suppressed RF signal coupling to the lossy Si substrate and a high vertical voltage blocking capability. For RF performance, GaN HEMTs with a 650 nm gate exhibit an fT/fMAX value of 25.1/32.3 GHz and a maximum output power POUT of 2.2 W/mm at 4 GHz with a drain voltage VDS of 20 V, which is comparable with the performance of RF GaN HEMTs on a high-resistivity silicon substrate without the existence of the field plate. For power performance, the vertical breakdown voltage of the wafer is 1160 V, and the three-terminal lateral breakdown voltage is 885 V in a GaN HEMT with a gate-to-drain distance of 8 µm. The thick GaN layer on the LRS substrate scheme thus provides a compelling platform for monolithic integration of high-performance RF devices and high-voltage power devices. [ABSTRACT FROM AUTHOR]

The short circuit (SC) behavior of a newly developed GaN-HEMT/SiC-JFET cascode device is investigated in this work. The reverse leakage current through the drain-side PN junction (IR) of the SiC JFET under SC conditions is measured simultaneously during the SC event. IR of the SiC JFET increases to 6.4 A at the end of a 5-μs nondestructive SC pulse. The increase of IR during the SC pulse induces a turning point in the SC current waveform and a dramatic negative threshold voltage shift (>30 V) in the SiC JEFT, resulting in high transient drain-to-source voltage in the GaN HEMT. The underlying mechanism is associated with the increase of local potential in the P-type layer of the SiC JFET with inevitable spread resistance (RSPD). It is suggested that reducing RSPD can improve SC capability and high IR should be considered in SC failure mechanism analysis and the design of external gate resistance of the SiC JFET. [ABSTRACT FROM AUTHOR]

Short circuit (SC) capability of 650-V Schottky-type p-GaN gate high-electron-mobility transistors (HEMTs) under single and repetitive tests is characterized in this article. The investigated devices exhibit strong capability under a single SC test, but weak capability under repetitive SC tests with a bus voltage of 400 V and a gate drive voltage of 6 V. The failure mechanism under repetitive SC tests is revealed through electrothermal simulation and microscale failure spot analysis. Thermal fatigue cracks are formed due to the high temperature spike and local temperature fluctuations in the narrow GaN channel and buffer layers, leading to weak repetitive SC capability. The unique heat confinement effect in the GaN layer plays an important role in the formation of high temperature spike and fatigue cracks. The withstand time in a single SC test is several hundred microseconds due to fast drain current drop that results from high temperature and, to a lesser degree, the dynamic threshold voltage shift during the SC transient. The device failure in a single-event SC test is related to heat diffusion to a wider region. Some guidelines are proposed for handling and improving the repetitive SC capability. [ABSTRACT FROM AUTHOR]

The threshold voltage (VTH) of an enhancement-mode Schottky-type p-GaN gate high-electron-mobility transistor (HEMT) is found to have a special dependence on the drain bias. The device commonly requires higher gate voltage to switch on the transistor from a high-drain-voltage off-state than what is expected from the static device characteristics. The reason behind the dynamic VTH has been proved to be the floating p-GaN layer, where charges could be stored and further influence VTH under different drain bias. In this article, a SPICE-compatible equivalent circuit model is presented according to the structure of Schottky-type p-GaN gate HEMTs. It features a floating node to imitate the charge storage process within the gate stack. Compared to conventional models, the proposed model could accurately predict the dynamic VTH characteristics and switching behaviors of power electronics circuits, where Schottky-type p-GaN gate HEMTs are deployed as power transistors. The phenomena related to the dynamic VTH, including the disappearance of Miller plateau, the overestimated false-turn-on problem, and the higher reverse conduction loss are evaluated with a half-bridge circuit and the merits of the proposed model are verified. [ABSTRACT FROM AUTHOR]

A normally-off SiC-JFET/GaN-HEMT cascode device is recently proposed, featuring a cascode configuration that incorporates a high-voltage (i.e., 1200 V) SiC junction field effect transistor (JFET) and a low-voltage GaN high electron mobility transistor (HEMT). This cascode device exhibits superior thermal stability and switching performance compared to the SiC MOSFETs, but also inevitably presents challenge in dv/dt-control as the input gate does not directly control the high-voltage JFET. Since dv/dt-control is of great importance to the management and suppression of electromagnetic interference in power electronics systems, methods of controlling the dv/dt rates of SiC/GaN cascode devices need to be developed. In this article, we conduct systematic investigation on different dv/dt control schemes with theoretical analysis and experimental evaluation. A dv/dt-control method based on diode-clamped external JFET gate resistor is proposed and evaluated by comparing it with other more conventional methods. The proposed dv/dt-control method is verified to provide a balanced dv/dt-control on the device turn-on and turn-off. [ABSTRACT FROM AUTHOR]

Systematic characterizations of a cascode device with a low-voltage enhance-mode (E-mode) p-GaN gate high-electron mobility transistor as the control device and a high-voltage (HV) depletion-mode (D-mode) silicon carbide junction field effect transistor (JFET) as the voltage blocking device are presented in this article. The demonstrated device with a breakdown voltage rating of 1200 V and a static on-resistance (RON) of 100 mΩ features small device capacitances with fast switching speed, avalanche breakdown capability, thermally stable threshold voltage (VTH), and no dynamic RON degradation. To identify its safe operation in the off-state with a high drain bias, the off-state middle point voltage (VM) between the E-mode device drain and D-mode device source is investigated. A relatively low off-state VM is achieved under both static and dynamic modes. In addition to the device-level characterization, a custom-designed double-pulse test circuit is built to evaluate the transient switching performance of the cascode device. Optimal gate drive conditions are proposed to 1) overcome the drain bias induced positive dynamic VTH shift; and 2) suppress the increased dynamic off-state leakage current (IOFF) induced by on-state hole injection. Under 800 V/16 A testing conditions, high switching speed with the drain voltage peak slew rates of 72 V/ns during turn-on and 121 V/ns during turn-off is achieved. [ABSTRACT FROM AUTHOR]

In this article, an ultrathin-barrier (UTB) AlGaN/GaN diode featuring metal–insulator–semiconductor (MIS)-gated hybrid anode (MG-HAD) and in situ Si3N4 cap passivation is demonstrated. The intrinsic turn-on voltage (VON) as low as 0.31 V determined by the as-grown AlGaN-barrier thickness (4.9 nm) is obtained and the VON exhibits excellent uniformity. More importantly, benefit from the MIS-gated hybrid anode structure, the UTB MG-HAD features good thermal stability in reverse blocking capability. The device delivers a substantially low leakage less than 1~μm/mm at −300 V at high temperature (HT) up to 200 °C, which is more than 100 × lower than that in the reference device w/o gate dielectric. Besides, the device exhibits respectably improved dynamic characteristics due to the incorporation of in situ Si3N4-cap passivation layer and remote plasma pretreatment (RPP) prior to Al2O3 gate dielectric deposition. The UTB MG-HAD featuring precisely VON modulation and low reverse leakage is of great interest for power electronic applications. [ABSTRACT FROM AUTHOR]

A 1200-V/100-mΩ silicon carbide (SiC) junction field-effect-transistor (JFET)/ gallium nitride (GaN) high-electron-mobility-transistor (HEMT) hybrid power switch is demonstrated, which features a flip-chip copackaged cascode configuration incorporating a vertical SiC JFET and a lateral GaN-HEMT. The high-voltage SiC-JFET provides the high-voltage blocking capability while the low-voltage GaN-HEMT enables the normally-off gate control with superior switching characteristics. Compared to conventional SiC-JFET/Si-mosfet cascode devices, the SiC-JFET/GaN-HEMT cascode device exhibits fast switching speed, which has been validated by systematic characterizations including static/dynamic device-level measurements and board-level hard-switching tests. Meanwhile, the device is free from several notorious issues of high-voltage GaN power transistors such as dynamic on-state resistance degradation and threshold voltage shift. Such a wide-bandgap semiconductor-based hybrid switch is suitable to be deployed in high-power and high-efficiency power conversion systems. [ABSTRACT FROM AUTHOR]

In this paper, systematic characterization and the corresponding suppression strategies of dynamic OFF-state leakage current (${I}_{ \mathrm{\scriptscriptstyle OFF}}$) in Schottky-type p-GaN gate high-electron-mobility transistors (HEMTs) are presented based on fast pulsed ${I}$ – ${V}$ measurement and consecutive switching measurement. It is found that the high ${I}_{ \mathrm{\scriptscriptstyle OFF}}$ under dynamic pulse mode without hole injection is a result of the reduced voltage blocking capabilities (both lateral and vertical) with weaker trapping effect in the buffer, and the dynamic ${I}_{ \mathrm{\scriptscriptstyle OFF}}$ induced by ON-state hole injection is caused by further increased lateral conductivity through the buffer from source to drain. The corresponding behaviors under continuous waveforms with different switching conditions are analyzed to identify effective approaches for the suppression of dynamic ${I}_{ \mathrm{\scriptscriptstyle OFF}}$ in practical switching operations. A higher temperature is shown to be beneficial to the reduction of the dynamic ${I}_{ \mathrm{\scriptscriptstyle OFF}}$ induced by ON-state hole injection. To completely eliminate the dynamic ${I}_{ \mathrm{\scriptscriptstyle OFF}}$ caused by ON-state hole injection and minimize the OFF-state power consumption in practical power switching applications, a sufficiently large negative OFF-state gate bias (e.g., ${V}_{\text {GS}, \mathrm{\scriptscriptstyle OFF}}\le -{3}$ V) is recommended in the gate driver turn-off voltage design for the Schottky-type p-GaN gate HEMTs. [ABSTRACT FROM AUTHOR]

Commercially available normally-off GaN power high-electron-mobility transistor (HEMT) devices have typically adopted a p-GaN gate structure. In the gate region, there exist a Schottky junction (between gate electrode and the p-GaN layer) and a p-GaN/AlGaN/GaN heterojunction. As the p-GaN layer is not directly shorted to the gate electrode and conducting channel, it can be considered as electrically “floating.” With drain voltage changing during a switching process, the variation of net charge in the floating p-GaN layer would cause instability in threshold voltage. Besides, because of the distinctive features of the p-GaN gate HEMT structure under certain gate/drain bias, gate-related junction capacitances would exhibit behavior different from those of a Si mosfet. Consequently, the switching transient performance of a GaN transistor with a p-GaN gate could be significantly influenced by the aforementioned factors. In this work, the threshold voltage instability associated with the drain-to-gate voltage stress is first analyzed. Despite the difficulty in directly performing capacitance measurements inside the device structure, a hybrid physical-behavior modeling method is proposed. The model is capable of extracting the capacitance bias relationships with regard to the gate region from static terminal measurements. In previous works, the advanced analytical model would make modest change on a Si mosfet's model. As a result, without fully considering the specific features of a GaN transistor with the p-GaN gate, the simulated waveforms would exhibit 20–50% discrepancy from the experiment. In contrast, the proposed switching transient analytical approach would exhibit improved accuracy (<10% disparity). Consequently, the switching transient performance of the GaN transistor with the p-GaN gate could be more accurately evaluated. [ABSTRACT FROM AUTHOR]

A systematic analytical investigation of the charge distribution and gate control of the normally-off GaN double-channel MOS-HEMT (DC-MOS-HEMT) is presented in this paper. Compared to conventional GaN MOS-HEMT, the DC-MOS-HEMT features a thin AlN insertion layer (AlN-ISL) below the original two dimensional electron gas (2DEG) channel, thus forming a second channel at the interface between AlN-ISL and the underlying GaN. This paper reveals the impact of the AlN-ISL on the 2DEG distribution and the gate control of the channels. The sensitivity of ${V}_{\text {th}}$ against the recess depth is also analytically studied and is found to be nearly independent of the recess depth as long as the recess is terminated in the upper channel layer. The analytical results are well supported by numerical device simulations, and the physical mechanisms behind these findings are explained along with the analytical investigations. [ABSTRACT FROM AUTHOR]

The temperature dependence of current collapse (CC) in AlGaN/GaN high-electron mobility transistors on silicon substrate is studied in this paper. Devices without and with Si3N4 passivation are used to investigate the behavior of surface- and buffer-induced CC, respectively. It is found that the degree of surface-induced CC in unpassivated devices has a weak temperature dependence, which is induced by the cancelling out between enhanced carrier injection based on surface hopping and enhanced emission when the temperature is increased. On the other hand, the degree of buffer-induced CC in the Si3N4 passivated devices is reduced at higher temperature since the energy of hot electrons is reduced due to the phonon scattering and the trapping of hot electrons in the buffer is mitigated. Temperature-dependent transient measurement is also carried out to investigate the recovery process for these two type of CC. Two types of trap levels are identified in the unpassivated and Si3N4 passivated devices, respectively. The trap level $E1$ with an activation energy of 0.08 eV is supposed to be related to the surface trapping, while $E2$ with an activation energy of 0.22 eV is located in the buffer layer. [ABSTRACT FROM AUTHOR]

Al2O3–AlGaN/GaN metal–insulator–semiconductor high-electron-mobility transistors (MIS-HEMTs) featuring indium tin oxide transparent gate electrode are fabricated for the purpose of evaluating the gate reliability. The transparent gate electrode allows electroluminescence (EL) observation in the region directly under the gate, which cannot be performed in conventional MIS-HEMTs with opaque gate electrode. Normally OFF transparent-gate MIS-HEMTs were realized by implanting fluorine ions into the AlGaN barrier prior to the deposition of Al2O3. The dependence of EL on bias condition was investigated with the color of EL resolved by filters. Gate dielectric degradation in MIS-HEMTs was induced by OFF state drain-bias stress, as detected by the increased gate leakage current. Location of the gate degradation could be clearly identified by EL imaging through the transparent gate. From the EL image, the passivation layer under the overhang of T-shaped gate is found to be vulnerable to OFF-state stress, which is confirmed by simulation. [ABSTRACT FROM AUTHOR]

We investigate in detail the influence of AlN passivation on dynamic ON-resistance ( \(R_{\mathrm{{\scriptstyle ON}}}\) ) and electric field ( \(E\) -field) distribution in high-voltage AlGaN/GaN high electron mobility transistors (HEMTs) on a Si substrate based on pulsed \(I\) – \(V\) measurements, electroluminescence (EL) microscopy, and 2-D physics-based numerical device simulations. It is found that the dynamic \(R_{\mathrm{{\scriptstyle ON}}}\) increase has been significantly suppressed to below 10% at various temperatures ranging from −50 to 200 °C owing to the effective and robust compensation of deep acceptor-like trap states at the AlN/GaN (passivation/cap) interface by the additional positive polarization charges induced in the epitaxial AlN thin passivation layer grown in a plasma-enhanced atomic layer deposition system. To the best of our knowledge, this is the first time that highly suppressed current collapse in an AlGaN/GaN HEMT on a Si substrate within a wide temperature range is ever reported. By monitoring the dynamic \(R_{\mathrm{{\scriptstyle ON}}}\) for 100 consecutive 133-kHz switching cycles, its variation is observed to be less than 2.5%, indicating excellent stability of the passivation effectiveness. The electric field in an AlN-passivated device is found to be well confined at the drain-side gate edge, as shown in EL measurement and numerical simulation results. This phenomenon directly suggests that the virtual gate effect arising from surface trap charging has been effectively alleviated by the AlN passivation technique. [ABSTRACT FROM AUTHOR]

In this paper, we investigate the enhancement-mode (E-mode) LaLuO3 (LLO)-AlGaN/GaN metal-insulator-semiconductor high-electron mobility transistors (MIS-HEMTs) fabricated using fluorine (F) plasma ion implantation with a gate-dielectric-first planar process. The E-mode MIS-HEMTs exhibit a threshold voltage (VTH) of 0.6 V, a peak transconductance of \sim193~mS/mm, a small hysteresis of 0.04 V in linear region characterized by a pulse-mode current-voltage measurement, and significantly suppressed current collapse under high-drain-bias switching conditions. X-ray photoelectron spectroscopy and secondary ion mass spectrometry analyses manifest that the negatively charged F ions penetrating into the (Al)GaN barrier layer serve as the primary VTH modulation mechanism, whereas the F ions in the fluorinated LLO film form chemical bonds with La/Lu atoms and become charge-neutral. The suppressed current collapse is verified as an advantageous byproduct of the F plasma ion implantation that also fluorinated the SiNx sidewalls in the vicinity of the gate electrode, and therefore, suppress electron injection to the gate-drain access region. [ABSTRACT FROM AUTHOR]

We present the detailed dc and radio-frequency characteristics of an Al0.3Ga0.7N/GaN/In0.1Ga0.9N/GaN double-heterojunction HEMT (DH-HEMT) structure. This structure incorporates a thin (3 nm) In0.1Ga0.9N notch layer inserted at a location that is 6-nm away from the AlGaN/GaN heterointerface. The In0.1Ga0.9N layer provides a unique piezoelectric polarization field which results in a higher potential barrier at the backside of the two-dimensional electron gas channel, effectively improving the carrier confinement and then reducing the buffer leakage. Both depletion-mode (D-mode) and enhancement-mode (E-mode) devices were fabricated on this new structure. Compared with the baseline AlGaN/GaN HEMTs, the DH-HEMT shows lower drain leakage current. The gate leakage current is also found to be reduced, owing to an improved surface morphology in InGaN-incorporated epitaxial structures. DC and small- and large-signal microwave characteristics, together with the linearity performances, have been investigated. The channel transit delay time analysis also revealed that there was a minor channel in the InGaN layer in which the electrons exhibited a mobility slightly lower than the GaN channel. The E-mode DH-HEMTs were also fabricated using our recently developed CF4-based plasma treatment technique. The large-signal operation of the E-mode GaN-based HEMTs was reported for the first time. At 2 GHz, a 1 × 100 μm E-mode device demonstrated a maximum output power of 3.12 W/mm and a power-added efficiency of 49% with single-polarity biases (a gate bias of +0.5 V and a drain bias of 35 V). An output third-order interception point of 34.7 dBm was obtained in the E-mode HEMTs. [ABSTRACT FROM AUTHOR]

Fabrication and characterization of AlGaN/GaN HEMT inverters and ring oscillators utilizing integrated enhancement/depletion-mode (E/D-mode) AlGaN/GaN HEMTs are presented. The core technique is a CF4 plasma treatment that can effectively convert a D-mode AlGaN/GaN heterostructure to an E-mode heterostructure. A significant advantage of the plasma-treated E-mode HEMTs is that the gate current is reduced in both reverse- and forward-bias regions due to the effectively enhanced barrier height induced by the negatively charged fluorine ions in the AlGaN barrier. As a result, the input voltage swing is expanded by about 1 V for the E-mode HEMT, enabling convenient input/output logic level matching for multistage logic circuits such as ring oscillators. The fabricated 17-stage direct-coupled field-effect transistor logic ring oscillator using the 1-μm-gate technology can operate properly at a larger supply voltage of 3.5 V, and a minimum propagation delay of 130 ps/stage is achieved. [ABSTRACT FROM AUTHOR]

This paper presents a method with an accurate control of threshold voltages (Vth) of AlGaN/GaN high-electron mobility transistors (HEMTs) using a fluoride-based plasma treatment. Using this method, the Vth of AlGaN/GaN HEMTs can be continuously shifted from 4 V in a conventional depletion-mode (D-mode) AlGaN/GaN HEMT to 0.9 V in an enhancement-mode AlGaN/GaN HEMT. It was found that the plasma-induced damages result in a mobility degradation of two-dimensional electron gas. The damages can be repaired and the mobility can be recovered by a post-gate annealing step at 400 °C. At the same time, the shift in Vth shows a good thermal stability and is not affected by the post-gate annealing. The enhancement-mode HEMTs show a performance (transconductance, cutoff frequencies) comparable to the D-mode HEMTs. Experimental results confirm that the threshold-voltage shift originates from the incorporation of F ions in the AlGaN barrier. In addition, the fluoride-based plasma treatment was also found to be effective in lowering the gate-leakage current, in both forward and reverse bias regions. A physical model of the threshold voltage is proposed to explain the effects of the fluoride-based plasma treatment on AlGaN/GaN HEMTs. [ABSTRACT FROM AUTHOR]