Search

High-quality homogeneous junctions are of great significance for developing transition metal dichalcogenides (TMDs) based electronic and optoelectronic devices. Here, we demonstrate a lateral p-type/intrinsic/n-type (p-i-n) homojunction based multilayer WSe2 diode. The photodiode is formed through selective doping, more specifically by utilizing self-aligning surface plasma treatment at the contact regions, while keeping the WSe2 channel intrinsic. Electrical measurements of such a diode reveal an ideal rectifying behavior with a current on/off ratio as high as 1.2 × 106 and an ideality factor of 1.14. While operating in the photovoltaic mode, the diode presents an excellent photodetecting performance under 450 nm light illumination, including an open-circuit voltage of 340 mV, a responsivity of 0.1 A W-1, and a specific detectivity of 2.2 × 1013 Jones. Furthermore, benefiting from the lateral p-i-n configuration, the slow photoresponse dynamics including the photocarrier diffusion in undepleted regions and photocarrier trapping/detrapping due to dopants or doping process induced defect states are significantly suppressed. Consequently, a record-breaking response time of 264 ns and a 3 dB bandwidth of 1.9 MHz are realized, compared with the previously reported TMDs based photodetectors. The above-mentioned desirable properties, together with CMOS compatible processes, make this WSe2p-i-n junction diode promising for future applications in self-powered high-frequency weak signal photodetection.

Monolayer MoS2 is a direct bandgap semiconductor which is believed to be one of the most promising candidates for optoelectronic devices. Chemical vapor deposition (CVD) is the most popular method to synthesize monolayer MoS2 with a large area. However, many defects are always found in monolayer MoS2 grown by CVD, such as sulfur vacancies, which severely degrade the performance of devices. This work demonstrates a concise and effective method for direct growth of high quality monolayer MoS2 by using SiO2/Si substrates pretreated with sulfur vapor. The MoS2 monolayer obtained using this method shows about 20 times PL intensity enhancement and a much narrower PL peak width than that grown on untreated substrates. Detailed characterization studies reveal that MoS2 grown on sulfur vapor pretreated SiO2/Si substrates has a much lower density of sulfur vacancies. The synthesis of monolayer MoS2 with high optical quality and low defect concentration is critical for both fundamental physics studies and potential practical device applications in the atomically thin limit.

Two-dimensional heterojunctions exhibit many unique features in nanoelectronic and optoelectronic devices. However, heterojunction engineering requires a complicated alignment process and some defects are inevitably introduced during material preparation. In this work, a laser scanning technique is used to construct a lateral WSe2 p-n junction. The laser-scanned region shows p-type behavior, and the adjacent region is electrically n-doped with a proper gate voltage. The laser-oxidized product WOx is found to be responsible for this p-type doping. After laser scanning, WSe2 displays a change from ambipolar to unipolar p-type property. A significant photocurrent emerges at the p-n junction. Therefore, a self-powered WSe2 photodetector can be fabricated based on this junction, which presents a large photoswitching ratio of 106, a high photoresponsivity of 800 mA W-1, and a short photoresponse time with long-term stability and reproducibility. Therefore, this selective laser-doping method is prospective in future electronic applications.

Environmental influences are critical for the reliability of photoelectric devices, especially those using organic semiconductors. Among all the influence factors, the effect of relative humidity on the material's photoelectrical properties receives less attentions. To date, reported humidity effects are mostly related to the electrical properties. Their impact to the photoelectrical characteristics has rarely been investigated. In this work, we firstly report a detailed study on the dependency of material's photoelectrical properties on the relative humidity in photosensitive field effect transistors. It was found that both the amplitude and the decay time of the photocurrent indicated a profound dependency on the humidity. To further clarify the mechanism, experiments were carefully designed along with a simulation to recognize and to provide a detailed understanding on any possible influence factors in these processes. The results indicate a prominent co-existence of carrier-trapping and dielectric-polarization phenomena in the photoelectric device under the influences of humidity. Since the water molecules in the atmosphere are predominant, the observed variation in the photoelectrical properties can be explained.

Chemical vapor deposition (CVD) is the most efficient method to grow large-area two dimensional (2D) transition metal dichiacogenides (TMDCs) in high quality. Monolayer molybdenum disulfide (MoS2) and seed-assistant are the mostly selected 2D TMDC and growth strategy for such CVD processes, respectively. Though the advantages of seed catalysts in facilitating the nucleation, achieving higher yield and better repeatability, as well as their effects on the morphologies of as-grown MoS2 have been studied, the influence of seeding promoters on both optical and electrical properties of as-grown monolayer MoS2 is not known comprehensively, which is indeed critical for understanding fundamental physics and developing practical application of such emerging 2D semiconductors. In this report, we systematically investigated the effect of different seeding promoters on the properties of CVD-grown monolayer MoS2. It is found that different seed molecules lead to different impacts on the optical and electrical properties of as-grown monolayer MoS2. Among three different seed catalysts (perylene-3,4,9,10-tetracarboxylic acid tetrapotassium salt (PTAS), copper phthalocyanine (CuPc), and crystal violet (CV)), PTAS performs better in obtaining large area monolayer MoS2 with good optical quality and high electrical mobility than the other two. Our work gives a guide for modifying the properties of as-grown monolayer MoS2 and other 2D transition metal dichalcogenides in seeding promoters-assisted synthesis process.

Most viscosity sensors, which are important in the health, automotive and food production industries, are currently based on mechanical or optical approaches. They are not compatible with emerging flexible and wearable electronics consisting of various lightweight integrated sensors with more compact architecture and lower cost. Here we demonstrate an organic device for sensing the viscosity of nonelectrolyte aqueous solutions which can work at low viscosities (0.9–10 mPa·s). The photoconductivity of devices involving semiconductor/water interfaces was found to obey Walden's rule, suggesting that viscosity could be measured by electrical means. This may be a promising approach for the design of viscosity sensors for portable and wearable applications. Keywords: Viscosity sensors, Organic photosensors, Glucose aqueous solution, Photoelectrochemical cells, Walden's rule

Heterostructures with built-in electric fields are crucial for charge separation and lateral photovoltaic effect in current position-sensitive detectors (PSDs), which have to be produced by combining semiconductors with metal or other semiconductors to form various vertical junctions (e.g. Schottky junctions) via complicated and high-cost manufacture processes. In the present work, it was found that vertical junctions can be directly written and patterned inside graphene oxide (GO) films with gradient C/O ratios by laser scribing due to the optical filter effect of the films and the formation of reduced GO (rGO) layers. Such junctions were verified to show the capability for high-precision position sensing on the micrometer scale, owing to the lateral photovoltaic effect. These self-powered laser-scribed PSDs can exhibit a small nonlinearity of

Two-dimensional (2D) semiconductors, represented by 2D transition metal dichalcogenides (TMDs), exhibit rich valley physics due to strong spin-orbit/spin-valley coupling. The most common way to probe such 2D systems is to utilize optical methods, which can monitor light emissions from various excitonic states and further help in understanding the physics behind such phenomena. Therefore, 2D TMDs with good optical quality are in great demand. Here, we report a method to directly grow epitaxial WS2 and MoS2 monolayers on hexagonal boron nitride (hBN) flakes with a high yield and high optical quality; these monolayers show better intrinsic light emission features than exfoliated monolayers from natural crystals. For the first time, the valley Zeeman splitting of WS2 and MoS2 monolayers on hBN has been visualized and systematically investigated. This study paves a new way to produce high optical quality WS2 and MoS2 monolayers and to exploit their intrinsic properties in a multitude of applications. MOE (Min. of Education, S’pore)

In this investigation, we experimentally demonstrated a high-speed Gbps long-distance real-time visible light communication system based on non-return-to-zero on-off keying modulation by using a high-bandwidth Gallium nitride-based micro-LED with a modulation bandwidth of ∼230 MHz and a size of 40 μ m $ \times $ 40 μ m. The maximum real-time data rate obtained is up to 1.3 Gbps at a 3 m free-space transmission distance with a bit-error rate (BER) of 3.4 $ \times $ 10 –3 and 1 Gbps at a 10 m distance with a BER of 3.2 $ \times $ 10–3, both of which are underneath the forward error correction threshold of 3.8 $ \times $ 10–3 required for free-error operation. In addition, when the transmission distance is increased to 16 m in free space through reflecting the emission light beam by blue reflectors mounted on the wall, a data rate of 0.87 Gbps with a BER of 3.5 $ \times $ 10–3 is achieved successfully.

Microwave annealing (MWA) and furnace annealing are compared for their low thermal budget capability to improve the characteristics of ZnO-based thin-film transistors (TFTs). Both the ZnO channel and the Al2O3 gate dielectric are fabricated using atomic layer deposition. Using Si-wafer-susceptor assisted MWA with a substantial reduction of both annealing temperature and duration, significant improvements of the characteristics of the ZnO TFTs can be attained. A multi-step MWA process is found to further improve the characteristics of the TFTs. For the same microwave power and total duration, the field-effect mobility of the multi-step MWA TFT is 42% greater than that of the one-step MWA TFT with a similar sub-threshold swing. The multi-step MWA process can serve the purpose at temperatures as low as 220 °C.

Transition metal dichalcogenides (TMDCs) demonstrate great potential in numerous applications. However, these applications require a precise control of layer thickness at the atomic scale. In this work, we present an in-situ study of the self-limiting oxidation process in MoTe2 by ozone (O3) treatment. A precise layer-by-layer control of MoTe2 flakes can be achieved via multiple cycles of oxidation and wet etching. The thinned MoTe2 flakes exhibit comparable optical properties and film quality to the pristine exfoliated ones. Besides, an additional p-type doping is observed after O3 oxidation. Such a p-doping effect converts the device properties of MoTe2 from electron-dominated to hole-dominated ambipolar characteristics.

Photo-induced phase transitions (PIPTs) provide an ultrafast, energy-efficient way for precisely manipulating the topological properties of transition-metal ditellurides, and can be used to stabilize a topological phase in an otherwise semiconducting material. Using first-principles calculations, we demonstrate that the PIPT in monolayer MoTe$_2$ from the semiconducting 2H phase to the topological 1T$'$ phase can be triggered purely by electronic excitations that soften multiple lattice vibrational modes. These softenings, driven by a Peierls-like mechanism within the conduction bands, lead to structural symmetry breaking within sub-picosecond timescales, which is shorter than the timescale of a thermally driven phase transition. The transition is predicted to be triggered by photons with energies over $1.96$\,eV, with an associated excited carrier density of $3.4\times10^{14}$\,cm$^{-2}$, which enables a controllable phase transformation by varying the laser wavelength. Our results provide insight into the underlying physics of the phase transition in 2D transition-metal ditellurides, and show an ultrafast phase transition mechanism for manipulation of the topological properties of 2D systems., 3

In this report, an anomalous time-evolution of electrical current in organic thin-film transistors, OTFTs, is revealed by employing a specially tailored semiconductor composite channel. The composite is designed by controlling the density of carbon nanotubes dispersed in a host semiconducting polymer below electrical percolation. The current anomaly, which, to the best of our knowledge, has never been observed before, is directly correlated to strong many-body interactions instantaneously occurring in the system under investigation. In essence, two on-chain positively charged polarons are fused with an electrochemically generated negative hydroxyl ion, OH−, in the H2O/O2 redox reaction to form a trion. The trion, which is characteristic of the polymer, is intrinsically metastable and can dissociate to mobile polarons under the influence of electric field, temperature and/or light illumination. The rate of trion formation is almost three orders of magnitude higher than that of trion dissociation. The fast formation and slow dissociation of the trions is the cause responsible for the observed current anomaly. The metastable trion is, hence, of fundamental importance in the operation of OTFTs. Understanding the fundamentals pertaining to the anomalous phenomenon not only is crucial for design of more efficient devices but also can guide development of future, emerging applications of OTFTs.

Charge carriers in graphene exhibit distinct characteristics from those in other two-dimensional materials because of their chiral nature. Additionally, multiple Dirac cones that emerge in graphene superlattices have been regarded as an interesting point in condensed-matter physics in recent years. Here, we report an investigation of the magneto-conductance in graphene encapsulated on the top and bottom by aligned h-BN. The bottom h-BN is precisely aligned with graphene, while the top h-BN is rotated a very small angle relative to it. Such a heterostructure could spoil the commensurate state existing in precisely aligned graphene while the giant moiré superlattice remains. A clear signature of weak localization and weak anti-localization is observed at multiple Dirac cones. Both the weak (anti)localization and the universal conductance fluctuations exhibit strong dependencies on the carrier density, temperature and channel length. This artificial heterostructure allows one to explore quantum interference in graphene with a wide spectrum of electronic properties.

Photoinduced space-charges in organic optoelectronic devices, which are usually caused by poor mobility and charge injection imbalance, always limit the device performance. Here we demonstrate that photoinduced space-charge layers, accumulated at organic semiconductor-insulator interfaces, can also play a role for photocurrent generation. Photocurrent transients from organic devices, with insulator-semiconductor interfaces, were systematically studied by using the double-layer model with an equivalent circuit. Results indicated that the electric fields in photoinduced space-charge layers can be utilized for charge generation and can even induce a photovoltage reversal. Such an operational process of light harvesting would be promising for photoelectric conversion in organic devices.

White light generated by mixing the red, green, and blue laser diodes (RGB LDs) for simultaneous high-speed underwater wireless optical communication (UWOC) and high-efficiency underwater solid-state lighting (SSL) was proposed and demonstrated experimentally for the first time. The allowable maximum real-time data transmission rates of 3.2 Gbps, 3.4 Gbps, and 3.1 Gbps for RGB LDs with corresponding BERs of 3.6 × 10−3, 3.5 × 10−3 and 3.7 × 10−3 were obtained at a 2.3 m underwater transmission distance using an on-off keying (OOK) modulation scheme, respectively. And the corresponding UWOC aggregate data rate of 9.7 Gbps was achieved based on RGB LDs-based wavelength-division multiplexing (WDM) UWOC. Moreover, UWOC and underwater SSL by using RGB LDs mixed white light were investigated at different scenarios over an underwater link of 2.3 m. The RGB LDs mixed white light-based UWOC system without optical diffusers yielded a maximum allowable data rate of 8.7 Gbps with Commission International de l’Eclairage coordinates (CIE) of (0.3154, 0.3354), a correlated color temperature of 6322 K, a color rendering index of 69.3 and a corresponding illuminance of 7084 lux. Furthermore, optical diffusers were employed to provide large-area underwater SSL. The LDs mixed white light-based UWOC system with line and circle optical diffusers implemented data rates of 5.9 Gbps and 6.6 Gbps with CIE coordinates of (0.3183, 0.3269) and (0.3298, 0.3390), respectively. This work suggests the potential of LDs for applications in high-efficiency underwater white-light SSL and high-speed UWOC.

A novel tetranuclear lead-edta compound [Pb4(edta)(H2O)2(N3)4]n (1) (H4edta = ethylenediaminetetraacetic acid) has been synthesized by the reaction of PbF2 with H4edta and NaN3 mixed-ligands under hydrothermal conditions, and was characterized by elemental analysis, thermal analysis, luminescence, powder X-ray diffraction and single-crystal X-ray diffraction. The results of X-ray crystallographic analysis reveal that compound 1 is the first 3D Pb(II)-edta coordination polymer with a high ratio of lead. Remarkably, the edta4− ligand uses all its 10 donor atoms (8O ​+ ​2 ​N) coordinated to Pb(II) ions and formed a 2D layer. The 2D layers are further linked to a complex 3D coordination polymer by the inorganic chain [Pb5(N3)10]n. Time-dependent density functional theory (TDDFT) calculations reveal that the mechanism of the fluorescence emission is dominantly resulted from the ligand-to-metal charge transfer (LMCT) for 1, which is in good agreement with its fluorescence spectra and crystal structure. Optical absorption spectra indicate that 1 has wide optical band-gaps and can be probably used as wide optical band-gap semiconductor material.

Three Pb(II)-edta complexes, [Pb3(edta)(H2O)Cl2]n·(H2O)3n (1), [Pb5(edta)2(H2O)2X2]n·(H2O)2n (X = Cl (2), Br (3)) (H4edta = ethylenediaminetetraacetic acid) have been synthesized by the reaction of PbX2 and H4edta under hydrothermal conditions, and were characterized by elemental analysis, thermal analysis, luminescence, powder X-ray diffraction and single-crystal X-ray diffraction. The results of X-ray crystallographic analysis reveal that these complexes are the first bilayer two-dimensional (2D) Pb-edta coordination polymers with 1D channels. The bilayers of complexes 1, 2 and 3 are linked by [Pb2Cl4], [PbCl2] and [PbBr2] clusters with carboxylate groups respectively. They are 3D supramolecular structures which are resulted from different halogenide anions. The emission spectra of 1–3 are dominated by intense and broad emission bands which are resulted from the [PbX2] clusters. Optical absorption spectra indicate that theses complexes have wide optical band-gaps and can be probably used as wide optical band-gap semiconductor materials.

Dopant-segregated source/drain contacts in a p-channel Schottky-barrier metal-oxide semiconductor field-effect transistor (SB-MOSFET) require further hole Schottky barrier height (SBH) regulation toward sub-0.1 eV levels to improve their competitiveness with conventional field-effect transistors. Because of the solubility limits of dopants in silicon, the requirements for effective hole SBH reduction with dopant segregation cannot be satisfied using mono-implantation. In this study, we demonstrate a potential solution for further SBH tuning by implementing the dual implantation of boron (B) and aluminum (Al) in combination with microwave annealing (MWA). By using such a method, not only has the lowest hole SBH ever with 0.07 eV in NiSi/n-Si contacts been realized, but also the annealing duration of MWA was sharply reduced to 60 s. Moreover, we investigated the SBH tuning mechanisms of the dual-implanted diodes with microwave annealing, including the dopant segregation, activation effect, and dual-barrier tuning effect of Al. With the selection of appropriate implantation conditions, the dual implantation of B and Al combined with the MWA technique shows promise for the fabrication of future p-channel SB-MOSFETs with a lower thermal budget.

Graphene based field effect transistors (GFETs) are quite sensitive to surface effects, such as the influence from surface adsorbents. In this work, it demonstrates the meta/ferroelectric [P(VDF-TrFE)]/graphene(MFG) configuration can realize the novel nonvolatile memories where competition between the ferroelectric polarization and charging / discharging of graphene / interface traps has been addressed.

The future electronic application of graphene highly relies on the production of large-area high-quality single-crystal graphene. However, the growth of single-crystal graphene on different substrates via either single nucleation or seamless stitching is carried out at a temperature of 1000 °C or higher. The usage of this high temperature generates a variety of problems, including complexity of operation, higher contamination, metal evaporation, and wrinkles owing to the mismatch of thermal expansion coefficients between the substrate and graphene. Here, a new approach for the fabrication of ultraflat single-crystal graphene using Cu/Ni (111)/sapphire wafers at lower temperature is reported. It is found that the temperature of epitaxial growth of graphene using Cu/Ni (111) can be reduced to 750 °C, much lower than that of earlier reports on catalytic surfaces. Devices made of graphene grown at 750 °C have a carrier mobility up to ≈9700 cm2 V-1 s-1 at room temperature. This work shines light on a way toward a much lower temperature growth of high-quality graphene in single crystallinity, which could benefit future electronic applications.

Chemical vapor deposition synthesis of semiconducting transition metal dichalcogenides (TMDs) offers a new route to build next-generation semiconductor devices. But realization of continuous and uniform multilayer (ML) TMD films is still limited by their specific growth kinetics, such as the competition between surface and interfacial energy. In this work, a layer-by-layer vacuum stacking transfer method is applied to obtain uniform and non-destructive ML-MoS2 films. Back-gated field effect transistor (FET) arrays of 1L- and 2L-MoS2 are fabricated on the same wafer, and their electrical performances are compared. We observe a significant increase of field-effect mobility for 2L-MoS2 FETs, up to 32.5 cm2 V-1 s-1, which is seven times higher than that of 1L-MoS2 (4.5 cm2 V-1 s-1). Then we also fabricated 1L-, 2L-, 3L-, and 4L-MoS2 FETs to further investigate the thickness-dependent characteristics of transferred ML-MoS2. Measurement results show a higher mobility but a smaller current on/off ratio as the layer number increases, suggesting that a balance between mobility and current on/off ratio can be achieved in 2L- and 3L-MoS2 FETs. Dual-gated structure is also investigated to demonstrate an improved electrostatic control of the ML-MoS2 channel.

In the field of electronic gas sensing, low-dimensional semiconductors such as single-walled carbon nanotubes (SWCNTs) can offer high detection sensitivity owing to their unprecedentedly large surface-to-volume ratio. The sensitivity and responsivity can further improve by increasing their areal density. Here, an accelerated gas adsorption is demonstrated by exploiting volumetric effects via dispersion of SWCNTs into a percolating three-dimensional (3D) network in a semiconducting polymer. The resultant semiconducting composite film is evaluated as a sensing membrane in field effect transistor (FET) sensors. In order to attain reproducible characteristics of the FET sensors, a pulsed-gate-bias measurement technique is adopted to eliminate current hysteresis and drift of sensing baseline. The rate of gas adsorption follows the Langmuir-type isotherm as a function of gas concentration and scales with film thickness. This rate is up to 5 times higher in the composite than only with an SWCNT network in the transistor channel, which in turn results in a 7-fold shorter time constant of adsorption with the composite. The description of gas adsorption developed in the present work is generic for all semiconductors and the demonstrated composite with 3D percolating SWCNTs dispersed in functional polymer represents a promising new type of material for advanced gas sensors.

Layered two-dimensional semiconductors have attracted tremendous attention owing to their demonstrated excellent transistor switching characteristics with a large ratio of on-state to off-state current, Ion/Ioff. However, the depletion-mode nature of the transistors sets a limit on the thickness of the layered semiconductor films primarily determined by a given Ion/Ioff as an acceptable specification. Identifying the optimum thickness range is of significance for material synthesis and device fabrication. Here, we systematically investigate the thickness-dependent switching behavior of transistors with a wide thickness range of multilayer-MoS2 films. A difference in Ion/Ioff by several orders of magnitude is observed when the film thickness, t, approaches a critical depletion width. The decrease in Ion/Ioff is exponential for t between 20 nm and 100 nm, by a factor of 10 for each additional 10 nm. For t larger than 100 nm, Ion/Ioff approaches unity. Simulation using technical computer-aided tools established for silicon technology faithfully reproduces the experimentally determined scaling behavior of Ion/Ioff with t. This excellent agreement confirms that multilayer-MoS2 films can be approximated as a homogeneous semiconductor with high surface conductivity that tends to deteriorate Ion/Ioff. Our findings are helpful in guiding material synthesis and designing advanced field-effect transistors based on the layered semiconductors.

Layered 2D semiconductors are characterized by unique photoelectric properties and, therefore, constitute a new class of basic building block for next‐generation optoelectronics. However, their wid ...

Graphene is characterized by demonstrated unique properties for potential novel applications in photodetection operated in the frequency range from ultraviolet to terahertz. To date, detailed work on identifying the origin of photoresponse in graphene is still ongoing. Here, scanning photocurrent microscopy to explore the nature of photocurrent generated at the monolayer-multilayer graphene junction is employed. It is found that the contributing photocurrent mechanism relies on the mismatch of the Dirac points between the monolayer and multilayer graphene. For overlapping Dirac points, only photothermoelectric effect (PTE) is observed at the junction. When they do not coincide, a different photocurrent due to photovoltaic effect (PVE) appears and becomes more pronounced with larger separation of the Dirac points. While only PTE is reported for a monolayer-bilayer graphene junction in the literature, this work confirms the coexistence of PTE and PVE, thereby extending the understanding of photocurrent in graphene-based heterojunctions.

The effects of UV-ozone (UVO) treatment on the sensing behaviours of extended-gate field-effect transistors (EGFETs) that use Al2O3 as the sensing film have been investigated. The Al2O3 sensing films are UVO-treated with various duration times and the corresponding EGFET sensing behaviours, such as sensitivity, hysteresis, and long-term stability, are electrically evaluated under various measurement conditions. Physical analysis is also performed to characterize the surface conditions of the UVO-treated sensing films using X-ray photoelectron spectroscopy and atomic force microscopy. It is found that UVO treatment effectively reduces the buried sites in the Al2O3 sensing film and subsequently results in reduced hysteresis and improved long-term stability of EGFET. Meanwhile, the observed slightly smoother Al2O3 film surface post UVO treatment corresponds to decreased surface sites and slightly reduced pH sensitivity of the Al2O3 film. The sensitivity degradation is found to be monotonically correlated with the UVO treatment time. A treatment time of 10 min is found to yield an excellent performance trade-off: clearly improved long-term stability and reduced hysteresis at the cost of negligible sensitivity reduction. These results suggest that UVO treatment is a simple and facile method to improve the overall sensing performance of the EGFETs with an Al2O3 sensing film.

Transition metal dichalcogenides (TMDCs) in monolayer form have attracted a great deal of attention for electronic and optical applications. Compared to mechanical exfoliation and chemical synthesis, laser thinning is a novel and unique “on-demand” approach to fabricate monolayers or pattern desired shapes with high controllability and reproducibility. Its successful demonstration motivates a further exploration of the dynamic behaviour of this local thinning process. Here, we present an in-situ study of void formation by laser irradiation with the assistance of temporal Raman evolution. In the analysis of time-dependent Raman intensity, an empirical formula relating void size to laser power and exposure time is established. Void in thinner MoS2 flakes grows faster than in thicker ones as a result of reduced sublimation temperature in the two-dimensional (2D) materials. Our study provides useful insights into the laser-thinning dynamics of 2D TMDCs and guidelines for an effective control over the void formation.

Graphene-based optoelectronic devices, including reduced graphene oxide (RGO) devices, commonly exhibit a large dark current and low on/off ratio with high dark-power consumption and a small responsivity. In this study, semi-RGO-based infrared photodetectors were directly "written" by using lasers, which can exhibit a small dark current of approximately 12 µA/cm2 with a high responsivity of approximately 0.18 A/W at 1,550 nm. Both the dark current and response speed can be tuned with GO as the gate dielectric in a field-effect transistor structure. These findings suggest the possibility of the three-dimensional "writing" of a micro-optoelectronic device or system with a low cost and high performance.

To enable high-speed long-distance underwater optical wireless communication (UOWC) supplementing traditional underwater wireless communication, a low-power 520 nm green laser diode (LD) based UOWC system was proposed and experimentally demonstrated to implement maximal communication capacity of up to 2.70 Gbps data rate over a 34.5 m underwater transmission distance by using non-return-to-zero on-off keying (NRZ-OOK) modulation scheme. Moreover, maximum data rates of up to 4.60 Gbps, 4.20 Gbps, 3.93 Gbps, 3.88 Gbps, and 3.48 Gbps at underwater distances of 2.3 m, 6.9 m, 11.5 m, 16.1 m and 20.7 m were achieved, respectively. The light attenuation coefficient of ~0.44 dB/m was obtained and the beam divergence angle is 0.35°, so the aallowable underwater transmission distance can be estimated to be ~90.7 m at a data rate of 0.15 Gbps with a corresponding received light-output power of -33.01 dBm and a bit-error rate (BER) of 2.0 ×10-6. In addition, when the data rate is up to 1 Gbps, the UOWC distance is predicted to be ~62.7 m for our proposed UOWC system. The achievements we make are suitable for applications requiring high-speed long-distance real-time UOWC.

In this paper, capacitive-type humidity sensors were prepared by sequentially drop-coating the aqueous suspensions of zinc oxide (ZnO) nanopowders and polyvinyl pyrrolidone–reduced graphene oxide (PVP-RGO) nanocomposites onto interdigitated electrodes. Significant improvements in both sensitivity and linearity were achieved for the ZnO/PVP-RGO sensors compared with the PVP-RGO/ZnO, PVP-RGO, and ZnO counterparts. Moreover, the produced ZnO/PVP-RGO sensors exhibited rather small hysteresis, fast response-recovery time, and long-term stability. Based on morphological and structural analyses, it can be inferred that the excellent humidity sensing properties of the ZnO/PVP-RGO sensors may be attributed to the high surface-to-volume ratio of the multilayer structure and the supporting roles of the PVP-RGO nanocomposites. The results in this work hence provide adequate guidelines for designing high-performance humidity sensors that make use of the multilayer structure of semiconductor oxide materials and PVP-RGO nanocomposites.

Recently, organic–inorganic lead iodide perovskite has become one of the most promising emergent materials, which exhibits great potential in photovoltaics, lasing, laser cooling, etc. The building block of such great material is PbI2, a van der Waals (vdW) layered semiconductor material, which arouses increased interest also owing to its potential applications for X-ray and γ-ray detection, lasing, etc. Similar and even superior to some vdW layered materials such as thin layers of transition metal dichalcogenides like MoS2, WS2, MoSe2, or WSe2, PbI2 layers possess a direct bandgap of visible frequency with a wide range of thicknesses (>3 layers). This study reports the anti-Stokes photoluminescence (ASPL) of PbI2 layers, which is very rarely investigated at present. Universe and robust ASPL in both 4H- and 2H-PbI2 layers are observed and a phonon-assisted and multiphoton absorption up-conversion mechanisms are proposed through in situ temperature-dependent, incident laser-power-dependent measurements of both Stokes photoluminescence and ASPL. The successful observation and explanation of the universal anti-Stokes emission of PbI2 layers, will certainly enrich fundamental understandings of vdW layered semiconductors and perovskite, then further benefit to developing applications based on such emerging materials.

GaN-based light emitting diodes (LEDs) have been fabricated on sapphire substrates with different thicknesses of GaN buffer layer grown by a combination of hydride vapor phase epitaxy and metalorganic chemical vapor deposition. We analyzed the LED efficiency and modulation characteristics with buffer thicknesses of 12 µm and 30 µm. With the buffer thickness increase, cathodoluminescence hyperspectral imaging shows that the dislocation density in the buffer layer decreases from ∼1.3X10 8 cm-2 to∼1.0 X 10 8 cm-2, and Raman spectra suggest that the compressive stress in the quantum wells is partly relaxed, which leads to a large blue shift in the peak emission wavelength of the photoluminescence and electroluminescent spectra. The combined effects of the low dislocation density and stress relaxation lead to improvements in the efficiency of LEDs with the 30 µm GaN buffer, but the electrical-to-optical modulation bandwidth is higher for the LEDs with the 12 µm GaN buffer. A rate equation analysis suggests that defect-related nonradiative recombination can help increase the modulation bandwidth but reduce the LED efficiency at low currents, suggesting that a compromise should be made in the choice of defect density.