Search

Oxide-based thin-film transistors (TFTs) with a lateral in-plane electrode are self-assembled on paper substrates, and the electrical modulation effect of the in-plane electrode is investigated. A \SiO2-based solid-electrolyte film with high specific capacitance is used as the gate dielectric, and the operation voltage is reduced to less than 2.0 V. The threshold voltage (Vth) of such paper TFTs is tuned from -0.98 to 0.94 V by different voltage biases on the in-plane electrode. The threshold voltage shift (\Delta Vth) can be described by \Delta Vth = -(CG2/CG1)VG2, where CG2 and CG1 are the in-plane electrode and bottom-gate specific capacitance values. High electrical performance with a current on/off ratio of \6 \times \10^5 \sim \10^6, a subthreshold swing of 0.14 \sim 0.19 V/dec, and a mobility of \8.64 \sim \9.45\ \cm^2/\V\cdot \s is obtained at different in-plane electrode voltage biases. Such low-voltage paper TFTs are promising for low-cost and portable electronics. [ABSTRACT FROM PUBLISHER]

Microporous SiO2 can provide large electric-doublelayer (EDL) capacitance and negligible leakage current, owing to lack of electron carrier and limited mobility of mobile ions. The impedance spectroscopy (ionic-conductivity--frequency and capacitance--voltage characteristics) and Fourier-transformed infrared spectroscopy of microporous SiO2 are characterized, which demonstrated that such dielectric is actually a solid-electrolyte dielectric. InGaZnO4 thin-film transistors (TFTs) on paper substrates gated by microporous-SiO2 solid electrolyte are fabricated at roomtemperature.The largeEDL-specific capacitance (1.36 µF/ cm²) results in the paper TFTs operate at a battery-drivable low voltage of 1.0 V. Both depletion-mode (Vth = .0.45 V) and enhancement-mode (Vth = 0.25 V) operations are realized by rationally controlling the oxygen concentration in argon ambient during InGaZnO4 channel deposition. Electrical characteristics with an equivalent field-effect mobility of ~21 cm²/V ⋅ s, a current ON/OFF ratio of greater than 105, and a subthreshold swing of ~80 mV/dec are demonstrated at low frequencies, which are promising for portable paper electronics. [ABSTRACT FROM AUTHOR]

This paper provides an industry perspective on the present state of compact models for MOS transistors. It highlights the complexity of layout-dependent effects in modern transistors, reviews some common misunderstandings of MOS transistor capacitances, and introduces a new, structurally symmetric, “gate-as-input” equivalent network for these capacitances. Areas of focus for the future model developments are also proposed. [ABSTRACT FROM AUTHOR]

Detailed physics of the third quadrant electrical characteristics of 1.2-kV rated 4H-SiC accumulation (Acc) and inversion (Inv) channel MOSFETs, based on experimentally measured data and TCAD numerical simulations, are described in this paper for the first time. The power MOSFETs with various channel lengths (0.3, 0.5, 0.8, 1.1 $\mu \text{m}$) used in this paper were fabricated in a 6-in commercial foundry. Numerical simulations verified that there are two current paths in the third quadrant: 1) through the base region and 2) through the p-n body diode. This paper demonstrates that the Acc MOSFETs have a smaller third quadrant knee voltage (${V}_{{\text {knee}}})$ of −1.2 V compared with −1.9 V for the Inv MOSFETs (at ${V}_{g} = {0}$ V and room temperature). Numerical simulations show that this difference is due to a smaller potential barrier for electron transport from the drain to the source in the base region for accumulation channel devices than inversion channel devices. Acc devices are shown to have a lower voltage drop in the third quadrant. [ABSTRACT FROM AUTHOR]

In this paper, we present a detailed investigation of the impact of fin width (${w}_{\text {fin}}$) on tri-gate AlGaN/GaN metal–oxide–semiconductor high electron mobility transistors (MOSHEMTs). As ${w}_{\text {fin}}$ is reduced, the threshold voltage (${V}_{\text {TH}}$) increases, which is due to the enhanced gate control (especially for ${w}_{\text {fin}} < {200}$ nm) thanks to the 3-D geometry of the tri-gate, and the reduced carrier concentration (${N}_{\text {s}}$) caused by a more pronounced strain relaxation and sidewall depletion, as explored using Hall and capacitance–voltage (${C}$ – ${V}$) measurements. Normally- OFF operation was achieved for ${w}_{\text {fin}}$ close to the sidewall depletion width (${w}_{\text {dep}}$) of 19.5 nm, since the fin is depleted from its two sidewalls. The impact of ${w}_{\text {fin}}$ on ON-resistance (${R} _{{{ {6{8} {\text {ON}}}}}}$) and current capability (${I} _{\text {D},\text {max}}$) was also investigated, along with the influence of the effective source injection, the trench conduction and the filling factor (FF) on these key characteristics. The degradation caused by the tri-gate fin etching could be fully recovered by increasing the FF. Finally, we show that the tri-gate can reduce gate capacitance (${C}_{\text {G}}$) and charge (${Q}_{\text {G}}$) in normally- ON MOSHEMTs, depending on the design of the tri-gate and the gate voltage (${V}_{\text {G}}$), leading to a smaller ${R}_{{{ {6{8} {\text {ON}}}}}} \cdot {Q}_{\text {G}}$ product that is beneficial for high-frequency switching applications. The results in this paper offer insights into important phenomena in tri-gate GaN devices and are fundamental for the further advance of this technology. [ABSTRACT FROM AUTHOR]

The first part of this paper presented mymargin the device-level comparison of emerging materials (In0.53Ga0.47As and 2-D materials) and device architecture (NW FETs) with s-Si FinFETs. In order to further understand the performance and energy efficiency of these device options for future technology nodes, it is required to go beyond the device-level comparison by accounting for not only intrinsic but also the extrinsic parasitic elements. In this paper, we present the comparison of s-Si, In0.53Ga0.47As, and 2-D material-based n-type MOSFETs using the circuit-level figure of merits across three successive future technology nodes. The analysis incorporates both device characteristics obtained from an advanced quantum mechanical simulation tool and circuit-level comparison, which accounts for device parasitic elements and wiring load. The results show that 2-D material DG MOSFETs present a more energy-efficient device option than s-Si and In0.53Ga0.47As FinFETs in sub-0.7-V supply voltage regime and In0.53Ga0.47As nanowire (NW) FETs can outperform s-Si multi-gate (MuG) FETs and 2-D material FETs, but when considering non-idealities, s-Si NW FETs remain both faster and more energy-efficient device option. [ABSTRACT FROM AUTHOR]

A novel plasma Charge Accumulative Model (pCAM) by calculating time-integrated Fowler–Nordheim (FN) tunneling charges and field of the gate dielectric in plasma processes is proposed in this paper. Our prior studies have developed and presented a quantitative FinFET plasma recording device by an effective fin-shaped field effect transistor (FinFET) contact-to-metal coupling structure to record and quantify plasma ion charges created in FinFET backend processes. In this paper, a precise analytical model is proposed to model the magnitude of plasma ion charges, time-integrated stressing field, and the criteria of the plasma process for optimum FinFET process technology. The new pCAM is highly matching with the measurement result of 16- and 7-nm FinFET wafers. The model can be adapted to practically estimate the plasma damage with different charge types, process parameters, and ion distribution; it can optimize the FinFET process and further understand the plasma damage mechanism in charging processes of 7-nm FinFET and beyond. [ABSTRACT FROM AUTHOR]

The dielectric screening property of a semiconductor is very crucial for the electrical characteristics of a MOSFET, and which can be described mathematically by Poisson equation via the permittivity. While the theory and experiments have corroborated the permittivity reduction of nanoscale Si, this paper studies the electrical characteristics of MOSFETs considering the reduced channel permittivity by quantum transport simulations. It is found that the channel permittivity reduction may mitigate the short-channel effects, showing subthreshold swing improvement and threshold voltage shift of MOSFETs in nanoscale. Compared to quantization effects, the positive and negative impacts of the channel permittivity reduction on the devices in particularly nanoscale have been investigated. This paper elucidates the necessity of considering semiconductor permittivity reduction for nanoscale device design and simulations. [ABSTRACT FROM AUTHOR]

This paper clarifies the correct transmission mechanism, misattributed in the previous research, of a hydrogenated amorphous silicon thin-film transistor (a-Si:H TFT) device. Complete drain current–gate voltage (${I}_{\text {D}}$ – ${V}_{\text {G}}$) transfer characteristics including the forward and backward gate sweeps (gate voltage carried out in the OFF-state $\to $ on-state and the ON-state $\to $ OFF-state) are performed, and the physics models of an energy-band schematic are clearly explained. This paper reveals that the ${I}_{\text {D}}$ – ${V}_{\text {G}}$ curve stretch-out behavior of the subthreshold region is due to the leakage of the Poole–Frenkel region. At the Poole–Frenkel regions, electrons transfer to the drain terminal, and holes remain in the valance band of the a-Si:H bulk. The remaining holes represent the positive voltage and cause the electron barrier height lowering. This causes an increase in subthreshold current of the subthreshold region. Finally, three experiments are performed to prove the correctness of these models, and the a-Si TFTs device improvement methods will be proposed to enhance the stability and performance of product of the a-Si TFTs. [ABSTRACT FROM AUTHOR]

In this paper, we propose a novel reconfigurable ferroelectric FET (R-FEFET), which can reconfigure its operation between volatile and nonvolatile modes during run-time by dynamically modulating its hysteresis. The R-FEFET comprises of two gates with ferroelectric (FE) in both the gate stacks. One of these terminals serves as a regular gate, while the other is used as a control to introduce reconfigurability. Employing Landau–Khalatnikov equation-based FEFET model, we extensively analyze the device characteristics in both FinFET and planar technologies. We show that by changing the control voltage between 0 and 1 V, the hysteresis width (HW) can be modulated between 1.1 and 0.3 V. In addition, we show the device characteristics and advantages that R-FEFETs possess to overcome the drawbacks encountered with gate leakage in standard FEFETs. The hold margins in the nonvolatile mode of R-FEFETs increase by ~ $10\times $ with respect to standard FEFETs, and the drive current strengths in the volatile mode show 13% improvements when compared to standard FETs. Using the proposed R-FEFETs, we examine a low-power nonvolatile memory design in Part II of this paper. [ABSTRACT FROM AUTHOR]

In the domain of printed electronics (PE), field-effect transistors (FETs) with an oxide semiconductor channel are very promising. In particular, the use of high gate-capacitance of the composite solid polymer electrolytes (CSPEs) as a gate-insulator ensures extremely low voltage requirements. Besides high gate capacitance, such CSPEs are proven to be easily printable, stable in air over wide temperature ranges, and possess high ion conductivity. These CSPEs can be sensitive to moisture, especially for high surface-to-volume ratio printed thin films. In this paper, we provide a comprehensive experimental study on the effect of humidity on CSPE-gated single transistors. At the circuit level, the performance of ring oscillators (ROs) has been compared for various humidity conditions. The experimental results of the electrolyte-gated FETs (EGFETs) demonstrate rather comparable currents between 30%–90% humidity levels. However, the shifted transistor parameters lead to a significant performance change of the RO frequency behavior. The study in this paper shows the need of an impermeable encapsulation for the CSPE-gated FETs to ensure identical performance at all humidity conditions. [ABSTRACT FROM AUTHOR]

In this paper, a novel vertical phototransistor was reported and compared with planar phototransistors for the first time. As compared with the planar phototransistors, the vertical ones exhibited much better photoelectric performance, which is attributed to an ultrashort photo-generated holes transfer distance and a stronger excitons dissociating electrical field due to their ultrashort channel length (tens of nanometers). Moreover, in order to examine the transport and trapping of different carrier charges separately, the impact of [6,6]-phenyl C61-butyric acid methyl ester (PCBM) dopant on the performance of planar and vertical phototransistors was investigated. The vertical devices exhibited an ultrahigh responsivity (~6600 A/W) as well as an excellent detectivity ($\sim 7\times 10^{15}~\text{Jones}$) and a fast photoresponse (rise time of 0.28 s), whereas slight changes were observed in the planar ones with doping of PCBM. The high performance of the blend vertical phototransistors is due to the trapping of the photo-generated electrons with PCBM and the effective transport of holes due to the ultrashort channel length. This paper provided a promising pathway for low-cost, high-performance phototransistors. [ABSTRACT FROM AUTHOR]

The instability of amorphous indium–gallium–zinc oxide (a-IGZO) thin-film transistors (TFTs) under ultraviolet (UV) light was thoroughly investigated in this paper. Unlike in a darkened state, an off-state leakage current can be found in the dual-sweep I–V transfer curve of a-IGZO TFTs under UV light illumination. Furthermore, despite the same UV light condition, the forward sweep and reverse sweep show different I–V curves, representing two different physical mechanisms. First, the subthreshold swing degradation and threshold voltage shift to the negative direction in the forward sweep are due to the total channel barrier lowering and can be confirmed by changing the light exposure region. Second, in the reverse sweep, the suggested back-channel leakage current can be controlled by dual-gate TFTs. UV light exposure of the metal–insulator–semiconductor–metal structure verifies that the off-state leakage current passes through the back channel in a reverse sweep. Finally, the physical mechanism links between forward and reverse sweeps have comprehensive interpretation in this paper. [ABSTRACT FROM AUTHOR]

This paper describes the design and performance of two new high-resolution interline charge-coupled device image sensors for use in industrial, machine vision, and aerial photography applications. These sensors feature 4.5- $\mu \text{m}$ pixels, 4 outputs, fast dump gate, horizontal lateral overflow drain, and vertical electronic shutter. The 43-Mp sensor has a 35-mm optical format and the 50-Mp sensor has a larger format with a 2.175:1 aspect ratio that matches many modern mobile phone displays. This paper discusses the challenges and solutions to manufacture such large sensors with superior image quality such as uniformity, read noise, dark current, smear, transfer gate blooming, lag, and so on. [ABSTRACT FROM AUTHOR]

Oxide semiconductors are highly attractive for fabrication of large-area thin-film electronics because of their high electrical performance, low process temperature, high uniformity, and ease of industrial manufacturing. n-type oxide semiconductors, such as InGaZnO, are highly developed and have already been commercialized for backplane drivers of flat-panel displays. To date, developing CMOS technology is still an urgent issue in order to build low-power electronic circuits based on oxide semiconductors. In this paper, various CMOS circuits, including inverters, NAND, NOR, XOR, d-latches, full adders, and 7-, 11-, 21-, and 51-stage ring oscillators (ROs), are fabricated based on sputtered p-type tin monoxide and n-type InGaZnO. The inverters show rail-to-rail output voltage behavior, low average static power consumption of 8.84 nW, high noise margin level up to ~40% supply voltage, high yield of 98%, and high uniformity with negligible standard deviation. The NAND, NOR, XOR, d-latches, and full adders show desirably ideal input–output characteristics. The performances of ROs indicate small stage delay of $\sim 1~\mu \text{s}$ , extremely high uniformity and high yieldwhich are essential for large-area thin-film electronics. This paper may inspire constructions of low power, large area, large scale, and high-performance transparent/flexible CMOS circuits fully based on oxide semiconductors for applications beyond flat-panel displays. [ABSTRACT FROM AUTHOR]

In this paper, we propose a novel static random access memory (SRAM) unit cell design and its array structure consisting of single-gated feedback field-effect transistors (FBFETs). To verify the SRAM characteristics, the basic memory operations and write disturbances of the unit cell are investigated through the mixed-mode technology computer-aided design simulations. The unit cell exhibits the superior SRAM characteristics including a write speed of 0.6 ns, a fast read-out speed of ~0.1 ns, and a retention time of 3600 s. Furthermore, the unit cell design exhibits advantages in density, with a small cell area of 8F2, and in the power consumption; the standby power consumption is 0.24 nW/bit for holding “1” and negligible for holding “0.” Moreover, our SRAM array shows reliable ${3} \times {3}$ array operations without any disturbances. This paper demonstrates the promising potential of the FBFET SRAM for high-performance, high-density, and low-power memory applications. [ABSTRACT FROM AUTHOR]

In this paper, we propose a model for estimating short-channel effects (SCEs) in the shell-doped double-gate junctionless (JL) MOSFET. The main emphasis of this paper is to estimate SCEs by effectively capturing source/drain (S/D) extensions beyond the gate edges for different values of undoped core thickness (${T}_{\textsf {core}}$), shell doping (${N}_{\textsf {d}}$), gate length (${L}_{\textsf {g}}$), and gate (${V}_{\textsf {gs}}$) and drain (${V}_{\textsf {ds}}$) biases in subthreshold regime. The threshold voltage (${V}_{\textsf {th}}$), drain-induced barrier lowering and subthreshold swing (${S}$), extracted from transfer characteristics, are in good agreement with the simulation results. Results highlight the utility of shell doping and core thickness to provide an additional degree of freedom to control SCEs. The proposed model can be useful in estimating SCEs and optimizing core–shell JL architecture for low-power applications. [ABSTRACT FROM AUTHOR]

In this paper, the threshold voltage characteristics of silicon nanowire metal–oxide–semiconductor field-effect transistor (MOSFET) with a double-layer gate structure are presented. This type of device is considered to be the most promising application of nanodevice in ultralarge-scale integration, due to several advantages such as similar operation principle as the junctionless nanowire transistor, the screening effect of the upper gate (UG) to shield the lower gate MOSFETs from external electromagnetic disturbance, the tradeoff between the short channel and the thick-gate oxide layer, and the compatible fabrication process with the conventional MOS technology. In this paper, the relations of threshold voltage versus the gate length, the UG bias, the substrate bias, the drain bias, and the temperature are measured and analyzed. Moreover, the penetration effect of the UG electric field is proposed to interpret the short-channel characteristics of the device, and a piecewise curve model is presented to reveal the underlying physics of the relation of the threshold voltage versus the drain bias. The double-layer gate structure technology enables the design of many devices, such as small-signal analog circuit units, single-electron devices, and quantum bit cells. [ABSTRACT FROM AUTHOR]

This paper investigates the trapping mechanisms in gate-injection transistors (GITs) without and with a pdrain electrode, referred to as GITs and Hybrid-Drain-embedded GITs (HD-GITs), respectively, used to inject holes and reduce charge trapping effects. We compare the two sets of devices under both the OFF-state and semi- ON state, to investigate the role of hot electrons in favoring the charge trapping. The analysis is based on combined pulsed characterization, transient measurements, and electroluminescence (EL) characterization. We demonstrate the following relevant results: 1) GITs and HD-GITs have comparable and negligible dynamic ${R}_{ \mathrm{\scriptscriptstyle ON}}$ when trapping is induced in the OFF-state; under semi- ON state conditions, GITs suffer from significant dynamic ${R}_{ \mathrm{\scriptscriptstyle ON}}$ , while HD-GITs show no additional trapping with respect to OFF-state; 2) EL characterization carried out until ${V}_{\mathsf {DS}}= 500$ V in semi- ON conditions shows comparable features, suggesting that the electric field and hot-carrier density are similar in GITs and HD-GITs. This result indicates that the hot-electron trapping rate is identical for the two sets of samples, so the difference observed in dynamic ${R}_{ \mathrm{\scriptscriptstyle ON}}$ must be ascribed to a different detrapping rate; 3) transient ${R}_{ \mathrm{\scriptscriptstyle ON}}$ measurements indicate that the traps filled in the OFF-state conditions are the same as those filled by hot electrons in semi- ON, with ${E}_{a}= 0.8$ eV (possibly ${C}_{N}$); and 4) EL analysis under constant bias indicates that in GITs there is a time-dependent increase in the luminescence signal at the drain terminal, when the devices are biased with ${V}_{\mathsf {DS}}= 300$ V. Such effect, indicative of hot-electron trapping, is not observed in HD-GITs. Based on the experimental evidence collected within this paper, we conclude that—in the semi- ON state—the main difference between GITs and HD-GITs consists in a faster detrapping rate of hot electrons, achieved through hole injection from the pdrain terminal. [ABSTRACT FROM AUTHOR]

In this paper, we examine the interplay of two serious reliability issues in MOSFET devices, namely, bias temperature instability (BTI) and hot-carrier degradation (HCD). Most publications are devoted to the characterization of either BTI or HCD, and complex models have been developed to independently describe each degradation mode. However, very limited data are available on the interplay of both degradation regimes, particularly the effect of a drain bias onto the charging and discharging dynamics of oxide traps. Part I of this paper provides an extensive experimental study toward the impact of mixed-mode stress conditions on the dynamics of oxide defects. Here, we present the first microscopic modeling approach beyond a simple electrostatic approximation. We extend the existing nonradiative multiphonon theory by taking nonequilibrium processes such as full carrier distribution functions which include the effect impact ionization along the channel into account. To ultimately validate our framework, we compare simulation results and experimental data for a single-oxide defect as well as a large ensemble of traps in a MOSFET device. We show that our modeling approach accurately captures the rather puzzling measurement trends for a broad stress regime and allows developing the knowledge on how oxide defects can be affected by an increased drain stress. [ABSTRACT FROM AUTHOR]

Because of charge trapping in GaN HEMTs, dc characteristics of these devices are not representative of high-frequency operation. The advanced spice model GaN model presented in Part I of this paper is combined with a Shockley–Reed–Hall-based trap model, yielding a comprehensive FET model for GaN HEMTs which can accurately model GaN devices exhibiting trapping-related dispersion effects. Measurement results of the dc and pulsed output and transfer characteristics of a commercially available GaN HEMT are presented, trapping in the device is modeled, and excellent fit to the measured data is shown. This paper presents an accurate model of trapping which is validated for eight different quiescent bias points of pulse measurements, with quiescent drain voltage ranging from 5 to 20 V and quiescent gate voltage ranging from −2.8 to −3.8 V, and a large range of gate and drain voltages to which the device was pulsed in the pulse measurements and at which the device was measured in the dc measurements, with gate voltage ranging from −4 to 0.4 V and drain voltage ranging from 0 to 40 V. This paper also presents high-frequency (10 GHz) large-signal RF validation of the model for optimal complex load condition. [ABSTRACT FROM AUTHOR]

The p-n junction is the fundamental building block for electronics and photonics applications. In a conventional p-n junction, the performance parameters cannot be tuned due to the fixed doping level after ion implantation. In this paper, reconfigurable p-n or n-p junctions were built based on the ambipolar black phosphorus (BP) and other 2-D materials, namely, graphene and hexagonal boron nitride (h-BN). High-quality graphene/h-BN/BP/h-BN sandwich device was created by the dry transfer method in an inert environment. Graphene serves as the local back gate, which can tune BP partially into either n-type or p-type material. The rest of the BP channel can be controlled by the back gate. The BP encapsulated device can enable the high performance of the ideality factor down to 1.08 (p-n junction) and 1.18 (n-p junction). The device developed in this paper has a more balanced ideality factor than previously reported reconfigurable WSe2 and BP devices. By tuning the back gate and graphene gate, the BP device can be tuned into four operational quadrants, namely, n-n, n-p, p-n, and p-p junctions. Moreover, the hole mobility of BP is up to 404 cm2/ $\text {V}\cdot \text {s}$ at room temperature. Our work shows that the BP heterostructure is very promising for high-speed reconfigurable logic functions and circuits. [ABSTRACT FROM AUTHOR]

In this paper, we report on the assessment of self-amplified silicon–oxide–nitride–oxide–silicon (SONOS) memory device architecture for sub-50-nm gate length (${L}_{g}$) through calibrated simulations. Self-amplification (SA) effect in tunnel field-effect transistor-based SONOS (T-SONOS) memory device has been analyzed. Results show that memory window ($\Delta {W}$) in T-SONOS cell increases as buried oxide thickness increases due to capacitive coupling between the front and back gates. Although the enhanced $\Delta {W}$ can also be achieved in inversion-mode SONOS (I-SONOS) device, its performance is deteriorated when the gate length is scaled down. We have compared the performance of I-SONOS and T-SONOS memory devices for ${L}_{g}$ varying from 100 to 25 nm. Results highlight that I-SONOS device cannot be programmed at ${L}_{g} ={25}$ nm and thus deteriorate the memory operation. However, SA T-SONOS at ${L}_{g} = {25}$ nm achieves ${W} \sim {6}$ V. In addition, the effect of underlap on the performance of T-SONOS cell has been analyzed, and it is shown that memory operation of 25-nm T-SONOS device can further improved with a drain side underlap of 20 nm. This paper provides new opportunities to design SA T-SONOS memory device for the next-generation nonvolatile memories. [ABSTRACT FROM AUTHOR]

The application of capacitive deep trench isolation (CDTI) as a shared vertical transfer gate (VTG) in a back-side-illuminated CMOS image sensor pixel is investigated using 3-D device-level simulations. The parasitic capacitance existence between CDTI and deeply buried pinned photodiode (BPD), and also between CDTI and floating diffusion (FD) region, makes the charge transfer process more difficult. In order to design a lag-free pixel and obtain complete charge transfer from BPD to FD, various considerations regarding the device-level design should be taken into account which is discussed in this paper. A CDTI neighboring two pixels can be functionalized as a shared VTG. Using CDTI as shared VTG facilitates pixel miniaturization and can result in more circuit integration at the pixel surface. This paper proposes a ${2}\,\,\mu \text{m} \times {2}\,\,\mu \text{m}$ pixel with CDTI as shared VTG, an equilibrium full-well capacity of 4605 e−, and a complete charge transfer from BPD to FD. [ABSTRACT FROM AUTHOR]

This paper demonstrates a novel nanofabrication technology for producing high-density gated molybdenum (Mo) field-emitter array (FEA) based on modified nanosphere lithography (NSL). The arc-shaped side wall of gate apertures introduced by the conventional NSL process put obstacles in the formation of sharp cone-type emitters. In this paper, a two-method solution was employed to facilitate the realization of gate apertures with sharper cutting side wall which are beneficial for the formation of sharper gated Mo emitters. One method was softening nanosphere to enlarge the contact area between nanosphere and substrate. The other was optimizing gate film deposition conditions to dramatically reduce the diffraction effects. Due to the improvements in the geometrical shape of gated Mo emitters, a low-voltage working high-density gated Mo FEA was demonstrated in this paper. This is the first observation of remarkable electron emission from high-density gated Mo FEA fabricated using such as low-cost, high-throughput, and high-efficiency technique which is expected to substantially overcome the challenges in the traditional fabrication process and promotes the low-cost and large-area application of high-density gated field-emitter devices. In addition, the novel nanofabricating method is expected to offer a simple and scalable route which allows fabrication of many gated field-emission devices. [ABSTRACT FROM AUTHOR]

This paper demonstrates a high-performance black phosphorus nanoribbons field-effect transistor (BPNR-FET) and systematically investigates methods for enhancing its anisotropic carrier transport. The BPNR-FET shows a strong dependence on crystal orientation in which the best mobility performance is achieved in armchair-oriented nanoribbons. A downscaling of nanoribbon width is shown to improve the short-channel effect owing to a better electrostatic gate control. Furthermore, hydrogenation is employed to effectively passivate the dangling bonds and heal the nanoribbon edge defects, leading to nearly hysteresis-free transfer properties. By virtue of bandgap and contact-metal workfunction engineering, n-type BPNR-FET is successfully demonstrated, which enables complementary inverter circuits to be simultaneously realized. This paper unravels the superior performance underscores a conceptually new BPNR-FET, paving the way toward the development of non-planar devices and integrated circuits based on 2-D materials platform. [ABSTRACT FROM AUTHOR]

This paper proposes a semianalytical model to estimate short-channel effects for independent gate operation in double-gate (DG) junctionless (JL) MOSFET incorporating gate-to-source/drain underlap, through the solution of Poisson’s equations in the subthreshold regime. The model also accounts for the asymmetry in device operation through variation in gate oxide thicknesses, gate work functions, and underlap lengths. Subthreshold drain current, threshold voltage, and subthreshold swing, evaluated from the channel potential, show reasonable agreement with simulation data. Results suggest the use of negative back gate bias and longer underlap length to reduce off-current. This paper highlights the role of doping, underlap length, and back gate bias in tuning the threshold voltage. This model serves as a generic formulation (within limits) with different asymmetries to estimate, design, and optimize self-aligned DG JL transistors for subthreshold logic applications. [ABSTRACT FROM AUTHOR]

In this paper, a n-type junctionless FET (JLFET) with a p-type fin body (FB) is investigated using a 3-D numerical simulator. We show that the proposed device (FB-JLFET) with a p+ FB can control the electrostatic potential of the channel more efficiently for multi- ${V} _{\text{TH}}$ (threshold voltage) and dynamic threshold (DT) operation. Moreover, body bias application is implemented in FB-JLFET and a large body factor ($\gamma $) is predicted for wide range ${V} _{\text{TH}}$ modulation. Thanks to the stronger potential coupling between the channel and FB, the proposed device exhibits $\gamma $ improvement compared to the conventional JL bulk FinFETs under the same electrostatic control. In addition, DT operation is studied in the form of a JLFET for the first time and it exhibits 37% improvement of the on-state drive current and better subthreshold swing (S.S.) compared to FB-JLFET without DT. This paper provides the feasibility of multi- ${V} _{\text{TH}}$ operation with body bias mode for high performance or low-power applications and DT operation for high-speed circuits with low power consumption. [ABSTRACT FROM AUTHOR]

Most thin-film transistor (TFT) gate drivers integrated on the display panel use the carry signals between the stages. In our previous works, we found that these carry-type gate drivers are subject to the reliability problem in a flexible display, since the errors of the stressed stages are accumulated through the carry signals. This problem possibly leads to the failure of image refresh of the display device. Therefore, the carry-free gate driver can resolve the error accumulation problem since it does not use the carry signals and instead, each unit stage operates independently. In this paper, we propose an advanced carry-free gate driver circuit to remove the drawbacks of the previous version, while keeping the advantages. More importantly, this paper is the first report to experimentally show that the error accumulation phenomenon of the carry-type gate driver and the problem is removed in the carry-free gate driver. The proposed carry-free gate driver and the carry-type gate driver are fabricated with amorphous indium-gallium-zinc-oxide TFTs on a flexible substrate for comparison purpose. The proposed gate driver shows a very high reliability since no voltage fluctuation occurs at the outputs after 10 000 cycles bending test with 2-mm bending radius. [ABSTRACT FROM AUTHOR]

This paper investigates the degradation of GaN-based HEMTs with p-type gate submitted to positive gate bias stress. Based on combined electrical and optical testing, we demonstrate the existence of different degradation processes, depending on the applied stress voltage ${V}_{\textsf {Gstress}}$ : 1) for ${V}_{\textsf {Gstress}}< \textsf {7}$ V, no significant degradation is observed, thus demonstrating a good stability of the analyzed technology; 2) for 7 V $< {V}_{\textsf {Gstress}} <\textsf {11.5}$ V, a negative shift in threshold voltage (${V}_{\textsf {th}}$) is observed, well correlated with a decrease in the gate leakage current and of the luminescence signal associated with hole injection. The negative ${V}_{\textsf {th}}$ shift is ascribed to the trapping of holes in the AlGaN and/or p-GaN/AlGaN interface; and 3) for ${V}_{\textsf {Gstress}} \ge \textsf {12}$ V, threshold voltage recovers its initial value. This is ascribed to a net-negative charge, generated either by the trapping of electrons injected from the 2-D electron gas to the AlGaN or to the de-trapping of the holes injected in 2). The results described within this paper provide relevant information for understanding the degradation dynamics of normally off GaN transistors submitted to extremely high gate voltage levels far beyond maximum use. [ABSTRACT FROM AUTHOR]

A systematic analytical investigation of the charge distribution and gate control of the normally-off GaN double-channel MOS-HEMT (DC-MOS-HEMT) is presented in this paper. Compared to conventional GaN MOS-HEMT, the DC-MOS-HEMT features a thin AlN insertion layer (AlN-ISL) below the original two dimensional electron gas (2DEG) channel, thus forming a second channel at the interface between AlN-ISL and the underlying GaN. This paper reveals the impact of the AlN-ISL on the 2DEG distribution and the gate control of the channels. The sensitivity of ${V}_{\text {th}}$ against the recess depth is also analytically studied and is found to be nearly independent of the recess depth as long as the recess is terminated in the upper channel layer. The analytical results are well supported by numerical device simulations, and the physical mechanisms behind these findings are explained along with the analytical investigations. [ABSTRACT FROM AUTHOR]

In this paper, we explored the characteristic fluctuations induced by various random discrete dopants (RDDs) on gate-all-around silicon nanowire metal–oxide semiconductor field-effect transistors. A 3-D quantum-mechanically corrected transport model was employed to analyze the simulated devices. The statistical results indicate that the variation of threshold voltage ( ${V}_{\text {th}}$ ) not only can be reduced from 28.6% to 10.7% without channel doping and penetration from the source/drain into the channel, but also the variation of 3-dB frequency can be reduced from 8% to 2.7% due to the reduction of the variation of ${V}_{\text {th}}$. We reported that the high-frequency characteristic fluctuations (voltage gain and cutoff frequency) were dominated by electron mobility. This caused by RDDs from the drain extension exhibited less variability than that caused by RDDs from the source extension due to a reduced injection velocity near the S side and a negligible difference in the electron saturation velocity near the D side. This paper provides pertinent information on the design of high-frequency amplifier circuits in relation to devices with RDDs induced by variations in the semiconductor process. [ABSTRACT FROM AUTHOR]

String read current ( ${I}_{\textsf {read}}$ ) reduction with rising mold height and grain boundary traps is one of the major hurdle in the development of 3-D NAND flash memory. In this paper, we have investigated ${I}_{\textsf {read}}$ with variation in polysilicon channel grain size (GS), grain boundary trap density, and channel thickness ( ${T}_{\textsf {Si}}$ ), using TCAD. We find that under a critical value of GS, ${I}_{\textsf {read}}$ decreases with increase in ${T}_{\textsf {Si}}$. This is attributed to the fact that with smaller GS, the total number of grain boundaries and associated traps are significantly higher. Moreover, there exists a typical value of GS for which ${I}_{\textsf {read}}$ is independent of ${T}_{\textsf {Si}}$ , which is desirable to minimize the deviations in ${I}_{\textsf {read}}$ arising from ${T}_{\textsf {Si}}$ variations. The resulting tradeoff in the design of more efficient 3-D NAND flash is demonstrated and discussed. Further, it is found that ${I}_{\textsf {read}}$ increases significantly by limiting the polysilicon channel grain boundary trap concentration under 1012 cm−2. The results presented in this paper are crucial for optimizing ${I}_{\textsf {read}}$ and program/erase threshold voltage ( ${V}_{T}$ ) window, and serve as key guidelines in the design of 3-D NAND flash memory with better performance. [ABSTRACT FROM AUTHOR]

In negative capacitance field-effect transistors (NCFETs), drain current may decrease with increasing ${V}_{\mathrm {ds}}$ in the saturation region, leading to negative differential resistance (NDR). While NDR is useful for oscillator design, it is undesirable for most analog circuits. On the other hand, the tendency toward NDR may be used to reduce the normally positive output conductance ( ${g}_{ \mathrm {ds}}$ ) of a short-channel transistor to a nearly zero positive value to achieve higher voltage gain. In this paper, we analyze the NDR effect for NCFET in the static limit and demonstrate that it can be engineered to reduce ${g}_{\mathrm {ds}}$ degradation in short-channel devices. Small and positive $g_{\mathrm{ ds}}$ is achieved without compromising the subthreshold gain, which is crucial for analog applications. The 7-nm ITRS 2.0 FinFET with 0.7 V ${V}_{\mathrm {dd}}$ is used as the baseline device in this paper. [ABSTRACT FROM AUTHOR]

This paper presents experimental and simulation analysis of an $\Omega $ -shaped silicon junctionless nanowire field-effect transistor (JL-NWT) with gate lengths of 150 nm and diameter of the Si channel of 8 nm. Our experimental measurements reveal that the ON-currents up to 1.15 mA/ $\mu \text{m}$ for 1.0 V and 2.52 mA/ $\mu \text{m}$ for the 1.8-V gate overdrive with an OFF-current set at 100 nA/ $\mu \text{m}$. Also, the experiment data reveal more than eight orders of magnitude ON-current to OFF-current ratios and an excellent subthreshold slope of 66 mV/dec recorded at room temperature. The obtained experimental current–voltage characteristics are used as a reference point to calibrate the simulations models used in this paper. Our simulation data show good agreement with the experimental results. All simulations are based on drift-diffusion formalism with activated density gradient quantum corrections. Once the simulations methodology is established, the simulations are calibrated to the experimental data. After this, we have performed statistical numerical experiments of a set of 500 different JL-NWTs. Each device has a unique random distribution of the discrete dopants within the silicon body. From those statistical simulations, we extracted important figures of merit, such as OFF-current and ON-current, subthreshold slope, and voltage threshold. The performed statistical analysis, on samples of those 500 JL-NWTs, shows that the mean ${I}_{D} - {V}_{\text {Gs}}$ characteristic is in excellent agreement with the experimental measurements. Moreover, the mean ${I}_{D} - {V}_{\text {Gs}}$ characteristic reproduces better the subthreshold slope data obtained from the experiment in comparison to the continuous model simulation. Finally, performance predictions for the JL transistor with shorter gate lengths and thinner oxide regions are carried out. Among the simulated JL transistors, the configuration with 25-nm gate length and 2-nm oxide thickness shows the most promising characteristics offering scalable designs. [ABSTRACT FROM AUTHOR]

There have been a lot of ambiguities related to physics of quasi-saturation (QS) in laterally diffused MOS (LDMOS) devices in the published literature. For example, models that explain QS in input characteristics do not explain the same in output characteristics and vice versa. In addition to this, none of the earlier models explain early onset of QS at higher temperatures nor the models were validated using counter arguments. Attributed to this, a need for unified theory explaining physics of QS is justified in this paper. Furthermore, this paper for the first time, while addressing missing links between the observations reported in the past, develops a unified theory to explain physics of QS behavior. The theory presented here is independent of device architecture and covers all voltage-current–temperature trends. While considering velocity saturation and space charge modulation, we have discovered key role of high field mobility degradation of majority carriers and electric field screening, which is found to be the root cause of QS in LDMOS devices. The theory presented is further validated with numerous counter arguments. Finally, based on the new physical insight developed, we have proposed different approaches to mitigate QS effect. A detailed device design guideline to mitigate QS and its correlation with analog/RF performance, electo static discharge, hot-carrier reliability, self-heating, and safe operating area concern is presented in Part II of this paper. [ABSTRACT FROM PUBLISHER]

Transconductance efficiency ( gm/{I}D ) is an essential design synthesis tool for low-power analog and RF applications. In this paper, the invariance of gm/{I}D versus normalized drain current curve is analyzed in an asymmetric double-gate (DG) fully depleted MOSFET. This paper studies the breakdown of this invariance versus back-gate voltage, transistor length, temperature, drain-to-source voltage, and process variations. The unforeseeable invariance is emphasized by measurements of a commercial 28-nm ultrathin body and box fully depleted Silicon-on-Insulator (SOI) (FDSOI) CMOS technology, thus supporting the gm/{I}D -based design methodologies usage in DG FDSOI transistors sizing. [ABSTRACT FROM AUTHOR]

In this paper, we present an experimental analysis of the degradation induced by positive bias temperature instability stress in GaN-based power high electron mobility transistors with p-type gate, controlled by a Schottky metal/p-GaN junction. In particular, the role of the aluminum content (Al%) in the AlGaN barrier layer on the threshold voltage degradation is investigated by means of constant voltage stress measurements. This has been performed for different process conditions with varying Al content. Main results in this paper demonstrate that when a relatively large positive bias is applied on the gate, two competing trapping mechanisms take place in the AlGaN barrier layer or at the p-GaN/AlGaN interface causing V\text {TH} instability. First, an aluminum independent hole trapping mechanism, caused by elastic tunneling from p-GaN valence band (2-D hole gas), leads to a relatively short-time and recoverable negative V\text {TH} shift. In the second step, defect creation occurs. These additional defects are filled with electrons and cause a permanent or slowly recoverable positive V\text {TH} degradation. The amount of defect creation was dependent on the Al% in the barrier. [ABSTRACT FROM PUBLISHER]

With the development of novel device applications, e.g., in the field of Internet of Things or point-of-care personalized diagnostic systems, came an increased demand for MESFETs for fast and low-power consumption integrated circuits and active-matrix displays. In this paper, we present fabrication and characterization of transparent Ru–Si–O/In–Ga–Zn–O MESFETs on flexible substrates. The use of transparent conducting oxide, namely, Ru–Si–O, as Schottky gate electrode, allows for processing the devices at room temperature, enabling the utilization of such low-temperature substrates as polyethylene terephthalate foil and paper. It was shown that tuning the device geometry allows realization of transistors providing on-current up to 2 mA, while the highest on-to-off current ratio equals 2\times 10^\mathrm 5 , with off-current below 1 nA, carrier mobility in the channel exceeds 9 cm ^\mathrm 2\cdot \textV^\mathrm -1\cdot \texts^\mathrm -1 , and subthreshold swing is below 250 mV $\cdot $ decade ^{\mathrm { {-1}}} . [ABSTRACT FROM PUBLISHER]

In this paper, a physics-based compact model for calculating the semiconductor charges and gate capacitance of III-V nanowire (NW) MOS transistors is presented. The model calculates the subband energies and the semiconductor charges by considering the wave function penetration into the gate insulator, effective mass discontinuity at the semiconductor-oxide interface, 2-D confinement in the NW, and Fermi-Dirac statistics. The semiconductor charge expression proposed in this paper is completely explicit in terms of applied gate voltage, therefore, making it highly suitable for large circuit simulations. The model is also compared with the results from self-consistent Schrödinger-Poisson solver for different NW sizes and materials and found to be accurate over a wide range of gate voltages. [ABSTRACT FROM AUTHOR]

Parasitic capacitance in nanoscale FETs is becoming a dominant component of the total device capacitance which degrades device and circuit performance. This problem is exacerbated with the introduction of multigate FETs such as FinFET and gate-all-around FETs. In this paper, we introduce the corner spacer design for gate-all-around nanowire FET to significantly decrease parasitic capacitance with negligible degradation in ON-current. We show that the parasitic capacitance of a well-engineered corner spacer in a nanowire FET can be reduced by over 80% compared to the device with full nitride spacers. Ring oscillator stage delay and energy consumption of the corner spacer design are lower than the full spacer by over 50% each. This paper shows the possibility of engineering the spacers as a performance booster to continue scaling. [ABSTRACT FROM AUTHOR]

With lots of interest in negative capacitance field-effect transistors for ultralow-power complementary metal-oxide-semiconductor technology, negative capacitance thin-film transistors (NCTFTs) have also received much attention. Although previous studies on NCTFTs were done, the NC effect in organic-based TFTs was not studied yet. In this paper, P(VDF-TrFE) ferroelectric-gated P3HT semiconductor channel TFTs are experimentally demonstrated with solution-based fabrication process. Especially, this paper shed light on the NC effect in the organic based TFTs. The step-up current-voltage characteristics are repeatedly and reliably observed in diverse TFTs, and then, with the results, transconductance (gm) amplification implemented by the negative capacitance was delved. Moreover, with the aid of ferroelectric polarization switching, super steep-switching characteristic of the organic-based TFT was experimentally confirmed. These experimental results and discussion would be helpful in understanding NC effects in TFTs. [ABSTRACT FROM AUTHOR]

In contrast to the conventional planar p-i-n photodiode and a metal-semiconductor-metal photodetector, the 3-D dual-gate photosensitive thin-film transistor (TFT) architectures presented here attain excellent photoresponse characteristics. Operating the device in the subthreshold regime further boosts the photoconductive gain as a result of light-induced decrease in the threshold voltage. This paper presents design considerations along with a performance comparison between 3-D photosensitive TFTs that have π- and FIN-shaped channels and conventional TFT with a planar channel. Our paper shows that the π-shaped structure tends to have a higher sensitivity while the FIN-shaped counterpart is more responsive with wider dynamic range. For both structures, a measured photoconductive gain of 104~106% is obtained with spectral responsivity ranging from near UV to near IR, and the photoresponse time in the range of tens of milliseconds. The 3-D dual-gate photosensitive TFT architecture appears to be very promising for large-area, low-level UV, visible, and IR detection applications. [ABSTRACT FROM AUTHOR]

The physical mechanisms involved in the trapping and de-trapping processes associated with surface donor traps in gallium nitride (GaN) transistors are discussed in this paper. The paper challenges the conventional transient techniques adopted for extrapolating the trap energy level via experiments and TCAD simulations. Transient TCAD simulations were employed to reproduce the time-dependent electrical behavior of a metal-on-insulator field-effect transistor and explain the influence of the electric field and energy barrier on the transient time associated with the trapping and de-trapping mechanisms of surface traps. The comparison between three test structures and the relative variation of the trapping and de-trapping times with the bias and trap parameters leads to the suggestion of a proposed test structure and bias configuration to accurately extrapolate the energy level of surface traps in GaN transistors. [ABSTRACT FROM AUTHOR]

The main purpose of this paper is to introduce an ultracompact device for electrostatic discharge (ESD) protection based on a bipolar metal oxide silicon (BIMOS) transistor merged with a dual back-to-back silicon-controlled rectifier (SCR) for bulk and for ultrathin body box fully depleted (FD)-silicon on insulator (SOI) advanced CMOS technologies in the hybrid bulk thanks to process co-integration. It is well known that ESD protection is a challenge for IC in advanced CMOS technology. In this paper, an optimized solution is described through the concept, design, 3-D technology computer aided design (TCAD) simulation, and silicon characterization in 28-nm FD-SOI in hybrid bulk. Measurements are done thanks to transmission line pulsed (TLP), very fast TLP and dc behavior. Moreover, the overvoltage is investigated through very fast transient characterization system measurements. It demonstrates a promising candidate to protect against ESD event and to develop new ESD network dedicated to system on chip. [ABSTRACT FROM PUBLISHER]

In this paper, a p-channel vertical 4H-silicon carbide (SiC) MOSFET (SiC p-MOSFET) has been fabricated successfully for the first time as a potential candidate for the complementary inverter application. The static characteristics and the robustness, including short circuit and avalanche capabilities of the p-MOSFET, are experimentally tested. Moreover, the comparison between the p-MOSFET and similar rating n-MOSFET is carried out. The short-circuit capability is 15% higher than that of the n-channel MOSFET. Furthermore, this paper also provides the physical insights into the failure mechanism during the short-circuit transient of the p- and n-MOSFET. Meanwhile, an electro-thermal analytical model is proposed to explain the thermal distribution during this transient. Last, the avalanche withstand time of the fabricated SiC p-MOSFET is experimentally demonstrated to be 27% higher than that of the n-channel one. It is concluded that the SiC p-MOSFET could be a competitive power switch applicable for high-frequency complementary inverters. [ABSTRACT FROM PUBLISHER]

Conventionally, integrated drain-extended MOS (DeMOS) like high-voltage devices are designed while keeping only performance targets for a given application in mind. In this paper, for the first time, performance and reliability codesign approach using 3-D TCAD has been presented for various superjunction (SJ) type DeMOS devices. In this context, how to effectively utilize the SJ concept in a DeMOS device for System on Chip applications, which often has stringent switching and RF performance targets, is explored in detail in this paper. Moreover, design and reliability tradeoffs for switching and RF applications are discussed, while considering two unique sets, one with fixed breakdown voltage and other with fixed ON-resistance. Finally, hot carrier generation, safe operating area concerns, and electrostatic discharge physics are explored and compared using 3-D TCAD simulations. [ABSTRACT FROM PUBLISHER]

A low-leakage electrostatic discharge power clamp with adjustable triggering voltage ( Vt1) is proposed in this paper. By enabling the static detection path using the transient one, the proposed clamp achieves a wide range of adjustable Vt1 while maintaining low standby leakage current ( I\text {leak}) , which overcomes the flaw of traditional static clamps. Besides, the adjustable Vt1 with low I\text {leak} is attractive for nanoscale applications. Moreover, the proposed clamp achieves enhanced false-triggering immunity over traditional transient clamps. The proposed clamp is successfully verified in a 65-nm CMOS process. Aside from silicon verifications, detailed comparisons with prior arts and practical application concerns are also addressed in this paper. [ABSTRACT FROM PUBLISHER]

Wafer-scale, CMOS compatible graphene transfer has been established for device fabrication and can be integrated into a conventional CMOS process flow back end of the line. In Part I of this paper, statistical analysis of graphene FET (GFET) devices fabricated on wafer scale is presented. Device yield is approximately 75% (for 4500 devices) measured in terms of the quality of the top gate, oxide layer, and graphene channel. Statistical evaluation of the device yield reveals that device failure occurs primarily during the graphene transfer step. In Part II of this paper, device statistics are further examined to reveal the primary mechanism behind device failure. The analysis from Part II suggests that significant improvements to device yield, variability, and performance can be achieved through mitigation of compressive strain introduced in the graphene layer during the graphene transfer process. The combined analyses from Parts I and II present an overview of mechanisms influencing GFET behavior as well as device yield. These mechanisms include residues on the graphene surface, tears, cracks, contact resistance at the graphene/metal interface, gate leakage as well as the effects of postprocessing. [ABSTRACT FROM PUBLISHER]

Negative capacitance FETs (NCFETs) have attracted significant interest due to their steep-switching capability at a low voltage and the associated benefits for implementing energy-efficient Boolean logic. While most existing works aim to avoid the ID – VG hysteresis in NCFETs, this paper exploits this hysteresis feature for logic-memory synergy and presents a custom-designed nonvolatile NCFET D flip-flop (DFF) that maintains its state during power outages. This paper also presents an NCFET fabricated for this purpose, showing <10 mV/decade steep hysteresisedges and high, up to seven orders inmagnitude, R\text {DS} ratio between the two polarization states. With a device-circuit codesign that takes advantage of the embedded nonvolatility and the high R\text {DS} ratio, the proposed DFF consumes negligible static current in backup and restore operations, and remains robust even with significant global and local ferroelectric material variations across a wide 0.3–0.8 V supply voltage range. Therefore, the proposed DFF achieves energy-efficient and low-latency backup and restore operations. Furthermore, it has an ultralow energy-delay overhead, below 2.1% in normal operations, and operates using the same voltage supply as the Boolean logic elements with which it connects. This promises energy-efficient nonvolatile computing in energy-harvesting and power-gating applications. [ABSTRACT FROM PUBLISHER]