Search

In this paper, we present a comprehensive reviewand discussion of the state-of-the-art device technology and application development of GaN-on-Si power electronics. Several device technologies for realizing normally off operation that is highly desirable for power switching applications are presented. In addition, the examples of circuit applications that can greatly benefit from the superior performance of GaN power devices are demonstrated. Comparisonwith other competingpower device technology, such as Si superjunction-MOSFET and SiC MOSFET, is also presented and analyzed. Critical issues for commercialization of GaN-on-Si power devices are discussed with regard to cost, reliability, and ease of use. [ABSTRACT FROM AUTHOR]

Improvement of the AlGaN/GaN high-electron mobility transistor's (HEMT's) off -state breakdown voltage is achieved by implanting ^19\F^+ ions at an energy of 50 keV and dose of \1 \times \10^12\ \cm^-2 under the gate region using \BF3 as the source. The charge state of the implanted fluorine ions changes from positive to negative in the AlGaN/GaN structure because of fluorine's strong electronegativity. The negative-charged fluorine ions at the back side of the two-dimensional electron gas can raise the energy barrier of the GaN buffer layer under the channel, effectively blocking the current injected from the source to the high-field region of the GaN channel when the HEMT is biased at off-state. The source-injected electrons, if not blocked, could flow to the high-field region and initiate a premature three-terminal off-state breakdown in a conventional AlGaN/GaN HEMT. A 38% improvement of the three-terminal off-state breakdown voltage and 40% improvement of the power figure-of-merit VBD-off^2/Ron are achieved in the enhanced back barrier HEMT. [ABSTRACT FROM AUTHOR]

AlGaN/GaN high-electron mobility transistor's (HEMT's) off-state breakdown is investigated using drain-current injection techniques with different injection current levels. Competitions between the source leakage and gate leakage, pure leakage and impact ionization, and source- and gate-injection-induced impact ionization during the drain-injection measurement are discussed in detail. It was found that the breakdown originates from the source/gate leakage at low drain injection levels but is dominated by source/gate-induced impact ionization process at high drain injection currents. The source-induced impact ionization usually precedes the gate-induced impact ionization in low-gate leakage devices, resulting in a premature three-terminal off-state breakdown. We also found that the gate-bias value affects the breakdown voltage in the conventional three-terminal off-state breakdown I-V measurement and should be carefully considered. [ABSTRACT FROM AUTHOR]

A cost-effective engineered bulk silicon (EBUS) substrate technology is presented, featuring p-n junction implemented on bulk Si substrates using mainstream ion implantation and thermal annealing processes. Standard p-GaN/AlGaN/GaN heterostructures are successfully grown on the EBUS substrate and used to fabricate 200-V enhancement-mode p-GaN gate HEMTs. By creating deep trenches in the EBUS substrate to isolate the local P+ silicon regions underneath the high-side (HS) and low-side (LS) power switches, adverse effects (e.g., back-gating and dynamic ON-resistance degradation) in the use of conventional bulk Si substrate are all eliminated. The mechanism of crosstalk suppression in the GaN-on-EBUS platform is revealed in comparison with conventional GaN-on-Si platform and verified by a series of designed tests. [ABSTRACT FROM AUTHOR]

Recently, a GaN reverse-conducting high-electron-mobility transistor (RC-HEMT) has been demonstrated. The RC-HEMT features built-in distributive Schottky contacts, which provide a low-loss freewheeling path. The RC-HEMT offers the same functionality as an HEMT/Schottky barrier diode (SBD) pair, but consumes much less chip area, thus its ${R}_{ \mathrm{\scriptscriptstyle ON}}$ (ON-resistance $\times $ total device width) is significantly reduced. Theoretically, ${R}_{ \mathrm{\scriptscriptstyle ON}}$ of the RC-HEMT can approach that of an HEMT. In practice, due to certain geometry limitations, ${R}_{ \mathrm{\scriptscriptstyle ON}}$ of an RC-HEMT lies between an HEMT/SBD pair and a single HEMT. This work investigates the factors that influence ${R}_{ \mathrm{\scriptscriptstyle ON}}$ of the RC-HEMT using both experimental measurements and numerical simulations. It is found that ${R}_{ \mathrm{\scriptscriptstyle ON}}$ of the RC-HEMT is strongly affected by the geometry of the source and channel regions, where HEMT sections and SBD sections are interdigitally distributed. With coarse patterning of these regions, ${R}_{ \mathrm{\scriptscriptstyle ON}}$ of the RC-HEMT is close to the HEMT/SBD pair. Through proper geometry scaling, ${R}_{ \mathrm{\scriptscriptstyle ON}}$ of RC-HEMT is reduced and approaches that of HEMT. [ABSTRACT FROM AUTHOR]

Low-loss reverse-conducting normally- OFF double-channel AlGaN/GaN power transistor with the built-in Schottky barrier diode (SBD) has been systematically studied. This device features the MOS-gate section and SBD-anode section paralleled to an interdigital layout along the gate width direction. A common access region that conducts current at both forward and reverse ON-states is employed, which is beneficial to reduce the conduction loss. With a MOS-HEMT/SBD finger width of ${4}~\mu \text{m}/2~\mu \text{m}$ and a total width ratio of 2:1, the device exhibits a threshold voltage of +0.8 V at a drain current of ${10}~\mu \text{A}$ /mm and a low forward ON-resistance of $12.1~\Omega \cdot \text {mm}$. The Schottky metal contacts 2-DEG directly, which results in a low reverse turn-on voltage of −0.6 V (at −1 mA/mm) and low reverse ON-state voltage of −1.7 V (at −50 mA/mm). A leakage suppression MOS field plate (FP) is applied to shield the Schottky contact from the strong electric field, leading to a low OFF-state leakage current of 14 nA/mm at +100-V drain bias and a high breakdown voltage (BV) of +698 V. The finger width and the number of fingers should be optimized. A narrow finger width benefits the current sharing at the access region, while the increasing number of fingers introduces more Schottky depletion regions along the gate width direction that degrade ${R}_{ \mathrm{\scriptscriptstyle ON}}$. [ABSTRACT FROM AUTHOR]

In this paper, we carried out a systematic comparison between the enhancement-mode GaN-based fully recessed metal-insulator-semiconductor field-effect transistors (MIS-FETs) and partially recessed MIS-high-electron-mobility transistors (MIS-HEMTs) with the same gate dielectric stack (LPCVD-SiNx/PECVD-SiNx) that has delivered promising long-term reliability and stability. Despite a moderately larger on-resistance (${R}_{ \mathrm{ON}}$), the MIS-FETs deliver superior ${V}_{\text {TH}}$ uniformity and thermal stability. Under long-term gate bias stress, both the MIS-HEMT and MIS-FET deliver similar small positive-bias temperature instability, while the negative-bias temperature instability of the MIS-HEMT is much larger than that of MIS-FET. The MIS-FET also delivers a higher ${V}_{\text {TH}}$ stability than the MIS-HEMT under dynamic gate bias stress. It is suggested that the differences in ${V}_{\text {TH}}$ stability mainly originate from the different spatial separation between the trap states and the conducting channel, with it being larger in MIS-HEMT than in MIS-FET. [ABSTRACT FROM AUTHOR]

A systematic analytical investigation of the charge distribution and gate control of the normally-off GaN double-channel MOS-HEMT (DC-MOS-HEMT) is presented in this paper. Compared to conventional GaN MOS-HEMT, the DC-MOS-HEMT features a thin AlN insertion layer (AlN-ISL) below the original two dimensional electron gas (2DEG) channel, thus forming a second channel at the interface between AlN-ISL and the underlying GaN. This paper reveals the impact of the AlN-ISL on the 2DEG distribution and the gate control of the channels. The sensitivity of ${V}_{\text {th}}$ against the recess depth is also analytically studied and is found to be nearly independent of the recess depth as long as the recess is terminated in the upper channel layer. The analytical results are well supported by numerical device simulations, and the physical mechanisms behind these findings are explained along with the analytical investigations. [ABSTRACT FROM AUTHOR]

(Al)GaN recess-free normally OFF technology is developed for fabrication of high-yield lateral GaN-based power devices. The recess-free process is achieved by an ultrathin-barrier (UTB) AlGaN/GaN heterostructure that features a natural pinched-off 2-D electron gas channel. The top–down manufacturing technique overcomes the challenges in etching of AlGaN barrier with well-controlled depth and uniformity, which is especially attractive for fabrication of normally OFF GaN-based high-electron-mobility transistors (HEMTs) and metal–insulator–semiconductor HEMTs (MIS-HEMTs) on large-size Si substrate. With SiNx passivation grown by low-pressure chemical-vapor deposition, on-resistance of the UTB-AlGaN/GaN-based power devices can be significantly reduced. High-uniformity low-hysteresis normally OFF HEMTs and Al2O3/AlGaN/GaN MIS-HEMTs are successfully demonstrated on the UTB AlGaN/GaN-on-Si platform. It is also a compelling technology platform for manufacturing high-performance GaN-based lateral power diodes, and normally OFF p-(Al)GaN heterojunction field-effect transistors. [ABSTRACT FROM PUBLISHER]

Bulk traps in the high-resistivity buffer stack underneath the 2-dimensional electron gas (2DEG), which can interact with the high vertical electric field at OFF state, impose a critical challenge to the dynamic ON-resistance (RON) of AlGaN/GaN-on-Si power devices. In this paper, the impact of substrate bias polarity on carrier injection/transport and buffer-induced current collapse has been investigated by using ramped and transient back-gating characterizations as well as TCAD simulations. High voltage applied to the conductive Si substrate can modulate 2DEG conductivity through the back-gate effect, whereby the dynamics of both acceptor and donor buffer traps are identified. Distinct buffer trapping and asymmetric vertical leakage under opposite top-to-substratebias polarities have been observed, which are attributed to the fundamentally different carrier injection/transport mechanisms. It is suggested that the energy barrier at the nucleation-layer/Si interface can limit the electron injection from Si substrate into the buffer stack and consequently influence the bufferrelated current collapse. [ABSTRACT FROM AUTHOR]

In this paper, we report a systematic study of the nitridation effects on GaN surface by first-principles calculations and X-ray/ultraviolet photoemission spectroscopy (XPS/UPS). According to the calculated electronic structures, two surface bands (i.e., the upper band and the lower band) can be seen within the bandgap for the typical surface configurations that may occur in the experimental condition as a result of surface reconstruction. By the deployment of sufficient nitridation, the energy positions of the lower band are modified toward the valence band by ~1 eV, resulting in the overlapping of the lower surface band with the valence band. Meanwhile, the upper surface band is also modified toward the valence band, but by a smaller amount. The modification to the positions of the surface bands is furthermore manifested by XPS/UPS spectra characterization performed on GaN sample that underwent surface treatment with low-energy remote N2 plasma. The theoretical and experimental results insightfully proclaim the nitridation effects on material properties at atomic level, and support a surface-state ionization model for the GaN band-edge (3.4 eV) emission in metal-AlGaN/GaN Schottky-on-heterojunction diode under forward bias. [ABSTRACT FROM PUBLISHER]

A GaN/SiC hybrid field-effect transistor (HyFET) is proposed as a high-voltage power device that provides a high-mobility lateral AlGaN/GaN channel to reduce the channel resistance and a vertical SiC drift region to sustain the high OFF-state voltage. The performance of the HyFET is evaluated by numerical device simulations. Compared with the conventional SiC MOSFET, the HyFET exhibits a greatly reduced R\mathrm{\scriptscriptstyle ON} together with a low C\mathrm{ GD} and low gate charges. The figures of merit Q\mathrm{ G}\times R\mathrm{\scriptscriptstyle ON} and Q\mathrm{ GD}\times R\mathrm{\scriptscriptstyle ON} of the HyFET are dramatically improved. [ABSTRACT FROM AUTHOR]

In this paper, we systematically investigated the leakage and breakdown mechanisms of the low-pressure chemical vapor deposition (LPCVD) silicon nitride thin film deposited on AlGaN/GaN heterostructures. The LPCVD-SiNx gate dielectric exhibits low leakage and high breakdown electric field. The dominant mechanism of the leakage current through LPCVD-SiNx gate dielectric is identified to be Poole–Frenkel emission at low electric field and Fowler–Nordheim tunneling at high electric field. Both electric-field-accelerated and temperature-accelerated time-dependent dielectric breakdown of the LPCVD-SiNx gate dielectric were also investigated. [ABSTRACT FROM PUBLISHER]

The temperature dependence of current collapse (CC) in AlGaN/GaN high-electron mobility transistors on silicon substrate is studied in this paper. Devices without and with Si3N4 passivation are used to investigate the behavior of surface- and buffer-induced CC, respectively. It is found that the degree of surface-induced CC in unpassivated devices has a weak temperature dependence, which is induced by the cancelling out between enhanced carrier injection based on surface hopping and enhanced emission when the temperature is increased. On the other hand, the degree of buffer-induced CC in the Si3N4 passivated devices is reduced at higher temperature since the energy of hot electrons is reduced due to the phonon scattering and the trapping of hot electrons in the buffer is mitigated. Temperature-dependent transient measurement is also carried out to investigate the recovery process for these two type of CC. Two types of trap levels are identified in the unpassivated and Si3N4 passivated devices, respectively. The trap level $E1$ with an activation energy of 0.08 eV is supposed to be related to the surface trapping, while $E2$ with an activation energy of 0.22 eV is located in the buffer layer. [ABSTRACT FROM AUTHOR]

Effective interface trap characterization approaches are indispensable in the development of gate stack and dielectric surface passivation technologies in III-nitride (III-N) insulated-gate power switching transistors for enhanced stability and dynamic performance. In III-N metal-insulator-semiconductor high-electron-mobility transistors (MIS-HEMTs) that feature a buried channel, the polarized barrier layer separates the critical dielectric/III-N interface from the two-dimensional electron gas (2DEG) channel and consequently complicates interface trap analysis. The barrier layer not only causes underestimation/uncertainty in interface trap extraction using conventional ac-conductance method but also allows the Fermi level dipping deep into the bandgap at the pinch-off of the 2DEG channel. To address these issues, we analyze the frequency/temperature dispersions of the second slope in capacitance-voltage characteristics and develop systematic ac-capacitance techniques to realize interface trap mapping in MIS-HEMTs. The correlation between ac-capacitance and pulse-mode hysteresis measurements show that appropriate gate bias need to be selected in the interface trap characterization of MIS-HEMTs, in order to match the time constant of interface traps at the Fermi level with ac frequency and pulsewidth. [ABSTRACT FROM AUTHOR]

We report the first gallium nitride (GaN)-based pulse width modulation (PWM) integrated circuit (IC) featuring monolithically integrated enhancement- and depletion-mode high electron mobility transistors and lateral field-effect rectifiers on the GaN smart power technology platform. The PWM IC is able to generate 1-MHz PWM signal with its duty cycle modulated effectively by a reference voltage ( Vc) over a wide range with good linearity. It features a 5 V supply voltage and is composed of a sawtooth generator and a comparator, both of which can be operated at 1 MHz and exhibit proper functionality over a wide temperature range (from 25 °C to 250 °C). This circuit demonstration further proves the feasibility of an all-GaN solution that features monolithically integrated peripheral gate control circuits and power switches for GaN power converters. An all-GaN solution would lead to a compact system with improved efficiency and enhanced reliability. [ABSTRACT FROM AUTHOR]

Al2O3–AlGaN/GaN metal–insulator–semiconductor high-electron-mobility transistors (MIS-HEMTs) featuring indium tin oxide transparent gate electrode are fabricated for the purpose of evaluating the gate reliability. The transparent gate electrode allows electroluminescence (EL) observation in the region directly under the gate, which cannot be performed in conventional MIS-HEMTs with opaque gate electrode. Normally OFF transparent-gate MIS-HEMTs were realized by implanting fluorine ions into the AlGaN barrier prior to the deposition of Al2O3. The dependence of EL on bias condition was investigated with the color of EL resolved by filters. Gate dielectric degradation in MIS-HEMTs was induced by OFF state drain-bias stress, as detected by the increased gate leakage current. Location of the gate degradation could be clearly identified by EL imaging through the transparent gate. From the EL image, the passivation layer under the overhang of T-shaped gate is found to be vulnerable to OFF-state stress, which is confirmed by simulation. [ABSTRACT FROM AUTHOR]

On a GaN smart power integrated circuit (IC) platform, a highly linear (i.e., proportional to absolute temperature) temperature sensor IC is demonstrated for building voltage references as well as temperature compensation functional blocks. The circuit is designed based on the temperature-dependent characteristics of GaN-based peripheral devices (e.g., heterojunction Schottky barrier diode, enhancement-/depletion-mode high electron mobility transistors, and lateral field-effect rectifiers) that are monolithically integrated with high-voltage power devices. This monolithic integration scheme facilitates the design efforts in taking full advantages of GaN’s superior capability to operate at high temperatures. Proper circuit operation was demonstrated at 275 °C. [ABSTRACT FROM AUTHOR]

In this paper, we report the device performance of a high-voltage normally off Al2O3/GaN MOSFET on the Si substrate. Normally off operation is obtained by multiple cycles of O2 plasma oxidation and wet oxide-removal gate recess process. The recessed normally off GaN MOSFET with 3 \mum gate-drain distance exhibits a maximum drain current of 585 mA/mm at 9 V gate bias. The threshold voltage of the MOSFET is 2.8 V with a standard derivation of 0.2 V on the sample with an area of 2 \,\times\, 2 {\rm cm}^{2} . The gate leakage current is below 10^{-6}~{\rm mA}/{\rm mm} during the whole gate swing up to 9 V and the I{\scriptstyleON}/I{\scriptstyle OFF} ratio is larger than 10^{9} , indicating the good quality of Al2O3 gate insulator. The MOSFET with 10 \mum gate-drain distance shows a three terminal OFF-state breakdown voltage (BV) of 967 V at zero gate-source bias with a drain leakage current criterion of 1 \muA/mm . The specific ON-resistance $(R_{{{\scriptstyle {\rm ON}}},{\rm SP}}) of the device is 1.6 m\Omega\,\cdot\,cm^2 and the power figure of merit (BV^2/R{{\scriptstyle ON},SP}) is 584 MW/cm^2 . [ABSTRACT FROM AUTHOR]

We experimentally demonstrate a high-voltage low-standby power startup circuit for powering up the off-line switched-mode power supply (SMPS) during the startup period by exploiting monolithically integrated enhancement/depletion-mode metal–insulator–semiconductor high electron mobility transistors (E/D-mode MIS-HEMTs) fabricated on a GaN-on-Si power device platform. The E/D-mode MIS-HEMTs exhibit a threshold voltage of +1.2 and -11~V, respectively. The high-voltage D-mode device used in the demonstration features an OFF-state breakdown voltage of 640 V and a safe operating area with a thermal limitation of 11.6 W/mm, whereas the low-voltage E-mode device features a source-gate breakdown voltage of 98 V, satisfying the requirement of the startup circuit. The functionality of the startup circuit is successfully achieved with an input voltage range 10–200 V and a startup current of 1.08 mA. [ABSTRACT FROM AUTHOR]

In this paper, we investigate the enhancement-mode (E-mode) LaLuO3 (LLO)-AlGaN/GaN metal-insulator-semiconductor high-electron mobility transistors (MIS-HEMTs) fabricated using fluorine (F) plasma ion implantation with a gate-dielectric-first planar process. The E-mode MIS-HEMTs exhibit a threshold voltage (VTH) of 0.6 V, a peak transconductance of \sim193~mS/mm, a small hysteresis of 0.04 V in linear region characterized by a pulse-mode current-voltage measurement, and significantly suppressed current collapse under high-drain-bias switching conditions. X-ray photoelectron spectroscopy and secondary ion mass spectrometry analyses manifest that the negatively charged F ions penetrating into the (Al)GaN barrier layer serve as the primary VTH modulation mechanism, whereas the F ions in the fluorinated LLO film form chemical bonds with La/Lu atoms and become charge-neutral. The suppressed current collapse is verified as an advantageous byproduct of the F plasma ion implantation that also fluorinated the SiNx sidewalls in the vicinity of the gate electrode, and therefore, suppress electron injection to the gate-drain access region. [ABSTRACT FROM AUTHOR]

In this paper, we demonstrate a 253% improvement in the off-state breakdown voltage (BV) of the lattice-matched \In0.17\Al0.83 \N/GaN high-electron-mobility transistors (HEMTs) by using a new Schottky-contact technology. Based on this concept, the Schottky-source/drain and Schottky-source (SS) InAlN/GaN HEMTs are proposed. The proposed InAlN/GaN HEMTs with an LGD of 15 \mu\m showed a three-terminal BV of more than 600 V, while the conventional InAlN/GaN HEMTs of the same geometry showed a maximum BV of 184 V. Without using any field plate, the BV of 650 V was measured in the SS InAlN/GaN HEMTs with LGD = \15\ \mu\m, which is the highest BV ever achieved on InAlN/GaN HEMT. The corresponding specific on-resistance (Rsp, on) is as low as 3.4 \m\Omega \cdot \cm^2. A BV of 118 V was also obtained in SS InAlN/GaN HEMTs with LGD = \1\ \mu\m, which is the highest BV in GaN-based HEMTs featuring such a short LGD with GaN buffer. The improvement of the BV relies on the effective suppression of source carrier injection into the GaN buffer under the SS due to the smooth metal morphology and elimination of metal spikes in the Schottky metallization. [ABSTRACT FROM AUTHOR]

In this paper, a zero-bias mixer using a lateral field-effect diode fabricated on standard GaN-on-Si AlGaN/GaN high electron-mobility-transistor wafers is demonstrated. The diode features strong nonlinearity near zero bias, enabled by a threshold-voltage modulation using a fluorine-plasma-treatment technique. The maximum change in conductance was adjusted to ~0 V, leading to optimal conversion loss (CL) of the mixer at zero bias and eliminating the need for any dc supplies. The mixer is characterized from room temperature (RT) to 250 °C. At 2.5 GHz and at RT, the CL and third-order intermodulation intercept point are 12.9 dB and 17.64 dBm, respectively. The operation of the proposed diode is modeled by a physical equivalent circuit, wit the element values extracted from the measured S-parameters. The voltage-biasing dependence of the CL can be explained by a the model. The high-temperature operation of the mixer shows that the proposed mixer can perform well in high-temperature and ultralow-power applications. [ABSTRACT FROM AUTHOR]

Fabrication and characterization of AlGaN/GaN HEMT inverters and ring oscillators utilizing integrated enhancement/depletion-mode (E/D-mode) AlGaN/GaN HEMTs are presented. The core technique is a CF4 plasma treatment that can effectively convert a D-mode AlGaN/GaN heterostructure to an E-mode heterostructure. A significant advantage of the plasma-treated E-mode HEMTs is that the gate current is reduced in both reverse- and forward-bias regions due to the effectively enhanced barrier height induced by the negatively charged fluorine ions in the AlGaN barrier. As a result, the input voltage swing is expanded by about 1 V for the E-mode HEMT, enabling convenient input/output logic level matching for multistage logic circuits such as ring oscillators. The fabricated 17-stage direct-coupled field-effect transistor logic ring oscillator using the 1-μm-gate technology can operate properly at a larger supply voltage of 3.5 V, and a minimum propagation delay of 130 ps/stage is achieved. [ABSTRACT FROM AUTHOR]

This paper presents a method with an accurate control of threshold voltages (Vth) of AlGaN/GaN high-electron mobility transistors (HEMTs) using a fluoride-based plasma treatment. Using this method, the Vth of AlGaN/GaN HEMTs can be continuously shifted from 4 V in a conventional depletion-mode (D-mode) AlGaN/GaN HEMT to 0.9 V in an enhancement-mode AlGaN/GaN HEMT. It was found that the plasma-induced damages result in a mobility degradation of two-dimensional electron gas. The damages can be repaired and the mobility can be recovered by a post-gate annealing step at 400 °C. At the same time, the shift in Vth shows a good thermal stability and is not affected by the post-gate annealing. The enhancement-mode HEMTs show a performance (transconductance, cutoff frequencies) comparable to the D-mode HEMTs. Experimental results confirm that the threshold-voltage shift originates from the incorporation of F ions in the AlGaN barrier. In addition, the fluoride-based plasma treatment was also found to be effective in lowering the gate-leakage current, in both forward and reverse bias regions. A physical model of the threshold voltage is proposed to explain the effects of the fluoride-based plasma treatment on AlGaN/GaN HEMTs. [ABSTRACT FROM AUTHOR]